Search Documents

By S. R. Borrowman

Physical beneficiation, leaching, and solvent extraction investigations were made to recover a high-grade thorium oxide product from Bald Mountain, Wyo., conglomerate. The monazite in the Bald Mountain deposit contains 8.8 percent Th02 and, therefore, is higher in thorium content than the usual domestic or foreign monazite. A sample of composited drill cuttings for the study contained 4.3 pounds of monazite per ton of are. The work showed that the monazite, although unusually fine grained and friable, could be concentrated by tabling and magnetic treatment to yield a product assaying 5.65 percent Th02 with a recovery of 61 percent of the thorium. Subsequent decomposition of the concentrate by treatment with sulfuric acid and solvent extraction of the resultant solution with a primary aliphatic amine yielded a thorium oxide product of 99-percent grade.

Jan 1, 1962

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By Edward Cogan

Equilibrium phase diagram studies of zirconium- rare earth metal alloys by the Bureau of Mines at its Albany Metallurgy Research Center prompted the development of a rapid gravimetric method for determining rare earths in zirconium in which the rare earths are absorbed from sulfuric acid solution of the alloy on a cation exchange resin . The sample in 10 percent H2SO4 is introduced into the column , the zirconium is eluted with 10 percent H2SO4 , and the rare earths are eluted with (NH4 )2SO4 solution and precipitated with NH4OH . A tracer technique was employed to determine the efficiency of the procedure . Y203 and europium 154 - 152 (Oak Ridge ) were added to 10 g of zirconium and taken through the entire procedure . Recovery averaged 97.6 percent on 0.002 μg europium in the rare earth fraction . Rare earths were determined in the range 0.10 to 90 percent .

Jan 1, 1964

By J. R. Ruark

This report presents results of mining operations and of research and development work done during stage I of the gas combustion retorting research program conducted by the Colorado School of Mines Research Foundation and six major oil companies at the Bureau of Mines Anvil Points Oil Shale Facilities. A brief description of the gas combustion process is given and the experimental program is discussed. Included in this discussion are (1) air-gas distributor development, (2) results of gas and shale distribution studies, and (3) effects of other process variable studies. The report concludes with a statistical evaluation of experimental results. Two appendixes present a chronological account of the experimental work and tabulations of data for all retorting runs conducted during stage I.

Jan 1, 1969

By H. D. Jacobs

The Bureau of Mines developed a concentration method to upgrade and utilize marginal natural or direct-shipping iron ores and fine-grained lean iron ores. Presently these ores receive little beneficiation and accordingly have low iron-silica (Fe-Si02) ratios. Ore samples were roasted with equal weights of solid reductant at 1,100° C for 1 hour to metallize the iron and for an additional hour at 1,200° C to promote grain growth. Concentration was effected by crushing and screening techniques and/or wet magnetic separation. Sized concentrates (minus 4 plus 35 mesh) derived from crushing-screening processes contained from 80 to 85 percent iron that was 90 percent metallized. Iron-silica ratios as high as 12:1 and iron recoveries from 75 to 94 percent were obtained. The sized concentrates were judged suitable for use as blast furnace feed. Minus 200-mesh metallized concentrates derived from roasted minus I-inch plus 8-mesh ore fractions and magnetically concentrated contained 90 percent Fe and 4 percent or less Si02, chemically qualifying them as feed for electric furnaces. Roasting minus 8-mesh ore with hydrogen, then magnetically concentrating it, produced iron concentrates containing 57 percent to 67 percent Fe and 3.6 percent to 8.4 percent Si02. The concentrates having Fe-Si02 ratios ranging from 8:1 to 12:1 were considered adequate for use as blast furnace feed. Overall iron recoveries for the 12 ores tested ranged from 56 percent to 94 percent with an average iron recovery of 86 percent.

Jan 1, 1969

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981

By John F. Papp

The Bureau of Mines has sampled microstructure of low-pressure flat flames by mass spectrometer for normal methane-oxygen-argon and for methane-oxygen-argon-bromotrifluoromethane flames. The physical and chemical phenomena, and the method of analysis of mole fraction data to evaluate net reaction rates are here considered in detail. Included is a computer program listing with output on one flame. Chemical species considered are CH4 , CO, CO2, H, H20, OH, Ar, H2, O2 , O, H2CO, CH3 , CF3Br, HF, HBr, Br, CH3Br, HCO, F2CO, CH2 CF2 , H02.

Jan 1, 1975

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 5,640-acre Soda Mountain Wilderness Study Area (OR-011-017), in order to evaluate its identified mineral resources. The study area is located in Jackson County, OR, about 30 miles south-east of Medford. The study area covers most of the south-facing slope of 6,071-ft Soda Mountain. Geologically, the area is underlain by Oligocene to Pliocene basaltic andesite flows and less extensive intrusive rocks of the western Cascade Mountains. In addition, there is a 3/4-mile-diameter area of kaolinized and silicified rhyolite tuff, which appears to have intruded the andesite, and is host to epithermal gold mineralization.

Jan 1, 1989

By Paul Biggs

This Bureau of Mines report provides information on 138 waterflood projects in Wyoming. Injection was in 25 producing zones and 65 fields. Specific data presented include field location, discovery and development, water supply and injection, oil and water production, estimates of oil in place, and oil recoveries by primary and secondary methods. The 138 projects studied will, if successful, recover about 800 million barrels of secondary oil. Almost all of the injection water is from deep water wells.

Jan 1, 1970

By K. O. Bennington

[Thermodynamic properties of two amphibole asbestos minerals were determined by the Bureau of Mines. The enthalpies of formation were determined by the hydrofluoric acid solution calorimetry method. Heat capacity measurements were made with an adiabatic calorimeter over the range of 5 to 315 K. High-temperature enthalpies above 298 K were determined with a copper-block drop calorimeter to 852 K for amosite and to 902 K for crocidolite. Thermodynamic data determined for amosite of the composition Fe5+2.2766Mg1.5209 Fe+03.12Mn0.0825) Si7.9163Al0.0837022.0363)(OH)1.9637 are: S°298 = 168.8 ± 5 cal/deg-mole; ?Hf°298-15 (elements) = -2419.24 ± 2.95 kcal/mole; ?Hf298.15 (oxides) = -30.92 ± 2.47 kcal/mole; and ?Gf° -2260.1 kcal. Corresponding data found for s3 ,1s = crocidolite of the composition (Na1.9Ca0.1)(Fe2+.024Fe2.5 01Mg0.475) (Si7.9713024Fe+2 2.501Mg0.475) (Si7.971 Al0.029022.095) (OH)1.905 are: S2.98-15 - 161.1 ± 4 cal/deg-mole; ?Rf° 2 298.15 (elements) = -2433.56 ± 2.99 kcal/mole, 10298.1s (oxides) = -87.69 1.70 kcal/mole, and ?Gf°298.15 = -2269.8 kcal.] Calorimetric values from this investigation were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and the constituent oxides.

Jan 1, 1978

By E. G. Davis

The flash reduction of fine iron ore in a dilute-phase system was investigated at 500° to 900° C within a heated stainless steel tubular coil. Alabama brown iron ore and Mesabi semitaconite ore were fed into the coil concurrently with reducing gases of hydrogen and reformed natural gas, so that the velocity of the gas at the reaction temperature was sufficient to entrain and pneumatically transport the solids through the coil. Reduction is very rapid with retention time of the ore in the coil varying from 4 to 15 seconds. Variables affecting reduction are temperature, ore feed rate, and gas flow or velocity. Results of the studies show that a partially reduced product (10-to 25-percent reduction) can be made which, on subsequent magnetic concentration, yields a concentrate containing 64 to 70 percent iron with a 90-to 94-percent iron recovery. Maximum reduction of 77 percent was obtained when hydrogen was used in a four-stage reduction test to yield a product containing 61 percent metallic iron.

Jan 1, 1972

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By Richard A. Thomas, Michael J. Sapko, Gary L. Mowrey, William D. Monaghan, Michael A. Trevits

Over the years, more than 20,000 mine seals have been erected in underground coal mines in the United States. Seals are used extensively in underground mines to isolate worked-out areas, active mine fire zones, and to control water inundations. Seals are most often built directly in the mine and can be fabricated from blocks made of wood or cementitious material. Recently, several explosions occurred within sealed areas of underground U.S. coal mines. These explosions, believed to be initiated by lightning strikes on the surface, destroyed numerous seals and caused considerable damage external to the sealed area. The National Institute for Occupational Safety and Health is conducting research to develop design guidelines, to investigate noninvasive techniques to characterize seal strength properties, and to evaluate seal test methods. As part of this work, a 30-ft wide, 16.1-ft tall and 4-ft thick seal was built in an underground experimental mine using cement and foamed water. Two types of noninvasive techniques are currently being investigated, namely the Schmidt Hammer for measuring compressive strength and ground penetrating radar (GPR) for detecting the presence of anomalies (e.g., voids, discontinuities) within the seal. Once these noninvasive tests were completed, the seal was subjected to destructive explosion testing. This study presents the results of the Schmidt Hammer tests, GPR scans, and the characteristics of seal failure during explosion testing.

By R. O. Dannenberg

Exploratory research was conducted to ascertain the feasibility of recovering beryllium from Spor Mountain, Utah, ore by the sodium fluosilicate (Na2SiF6) method used industrially for processing beryl. Na2SiF6 requirements to form water-soluble salts of beryllium were determined for three different samples--two clayey ores containing 0.6 and 1.3 pct BeO, respectively, and a calcareous ore containing 0.6 pct BeO. The ores were sintered with Na2SiF6 at 750° C for 3 hours. About 80 pct of the beryllium was rendered water soluble by sintering the 0.6-pct BeO ores with 30 and 40 lb Na2SiF6 per lb BeO contained in clayey and calcareous ores, respectively. The higher grade 1.3-pct BeO clayey ore required only 20 lb Na2SiF6 per lb BeO to solubilize over 80 pet of the beryllium. As the 0.6-pct BeO clayey ore was possibly the most representative of the deposit as presently delineated, leach liquor prepared from this sample was treated to recover beryllium salts. About 60 pet of the beryllium contained in the ore was recovered as beryllium hydroxide, which then was calcined to yield a 99-pct BeO final product by means of the following operations: (1) Sintering with Na2SiF2, (2) leaching with water, (3) precipitating crude Be(OH)2 by adding NaOH, (4) filtering to separate the hydroxide from the NaF solution, (5) redissolving the crude Be(OH)2 in excess NaOH, (6) filtering to reject caustic-insoluble impurities, and finally (7) boiling the Na2BeO2 filtrate from (8) to precipitate pure Be(OH)2. Reagent consumption was 49 lb Na2SiF6 per lb BeO recovered and 17 lb NaOH per lb BeO.

Jan 1, 1963

By Leon W. Dupuy

"INTRODUCTION Scheelite occurring in tactite at the Black Rock tungsten mine, near Benton in Mono County, Calif., was investigated by the Bureau of Mines in cooperation with the Geological Survey as part of their search for additional sources of supply of strategic minerals authorized under the Strategic Materials Act. 3/4/The work accomplished by the Bureau, and the assays of samples taken are described in this manuscript. The ore found aided materially in prolonging the operating life of the mine during the recent national emergency, supplying much-needed tungsten for war use. ACKNOWLEDGMENTSIn its program of investigations of mineral deposits, the Bureau of Mines has as its primary objective the more efficient utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual development work, and prepares the final report. The Metallurgical Division, under the direction of C. C. Ralston, chief, analyzes samples and performs beneficiatibn tests."

Mar 1, 1948

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By J. P. Coughlin

Gypsum plaster is calcium sulfate hemihydrate (CaS04-1/2H2O). There are two varieties, commonly designated as a and ß. The hydration setting) of this plaster involves the chemical reaction: CaS04?1/2H20(c) + 3/2H20(l) = CaSO4?2H20(c); that is, the hemihydrate combines with water to form the dihydrate. Many substances, when present as impurities, either in the hemihydrate or the water have influenced the rate of the hydration reaction. The objective of the Bureau of Mines work described in this report was to investigate the accelerating or retarding effects of small amounts of dissolved substances and to attempt to classify these effects upon a chemical basis. To eliminate competing effects, the work was conducted separately on the two varieties of hemihydrate; both were in highly pure form. (Commercial plasters usually are a mixture of the hemihydrates, with other substances present as impurities.) As the hydration reaction of each variety of hemihydrate evolves heat in amounts known from previous work, 5,6/ the authors decided to use calorimetric methods to follow the extent of the hydration reaction as a function of time. Two calorimetric methods were employed. One was designed to study the hydration reaction with a large water to plaster ratio and the other with a small water to plaster ratio (to simulate commercial practice in utilizing plaster).

Jan 1, 1959

By M. M. Hassan

This report describes the analysis tools developed at West Virginia University which can be implemented to optimally design coal mine electrical systems. The basic analytical tools for all power systems are the load-flow and short-circuit analysis. Well known programs have been developed for analysis of ac transmission and distribution systems, but they are not applicable to a system which has combined ac/dc distribution, such as a coal mine power system. Furthermore, the topology of a coal mine electrcal system changes continuously due to the movement of the locomotives on the track. In the first section of this report, algorithms for carrying out load flow and short-circuit analysis of a coal mine electrical system are described. Results from the study of a typical coal mine system are presented. In the second section a method is described to optimally size power cables for cyclic loads. The method is based on the development of a thermal-electric model for a low-voltage power cable. Results from experimental verification of the model are also presented. These techniques are useful in the safe, efficient, reliable and economical design of the coal mine electrical power systems.

Jan 1, 1979

By C. A. Alien

The increasing activity in oil shale has had a tendency to direct the attention of the industry to any substance from which gasoline or other oils can be secured . Cannel coal for many years has been known, as a source of oil and formerly it was the only substance from which kerosene was obtained . The name of coal oil was given to kerosene because it was derived from cannel coal before any flowing wells were brought in in the United States . In an isolated region in Southern Utah there is an unusually thick and clean bed of cannel coal which laboratory experiments indicate can be made to yield about seventy gallons of oil to the ton . This coal was first described in Bulletin 341 of the United States Geological Survey under the title of Colob coal field . This field lies at the western and southern base of the Colcb plateau and extends from the town of Cedar City southward to Kanarra and then southeastward to the town of Mount Carmel . Cedar City is 35 miles south of east from Lund on the Los Angeles and Salt Lake Railroad which is the nearest railroad point . Mount Carmel is about 90 miles south of Marysvale , on the Denver and Rio Grande Railroad , which is the nearest railroad point from the eastern end of the field . The Colob coal occurs in Lower Cretaceous rocks and a number of wagon mines have been opened on the seam in the vicinity of Cedar City , Kanarra , and Mt. Carmel , but between these places the field has been very little prospected . The cannel coal , so far as known at present , is limited to a small area on the head waters of the north fork of the Virgin River in Township 39 and 40 South , Range 9 East . In this region it occurs as a bed 5-1 /2 feet thick over which lies a layer of bituminous coal 2 feet and 5 inches thick .

Feb 1, 1921

By J. E. Tiffany, Z. C. Gaugler

"In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 20 and 25 outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible.In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 20 and condition 2 on page 25. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.PERMISSIBLE EXPLOSIVES TESTED UNDER SCHEDULE 17CAn active list of permissible explosives was published in October 1938 as part of Bureau of Mines Report of Investigations 3421, under the title ""Active List of Permissible Explosives and. Blasting Devices Approved Prior to June 30, 1938."" This list included 191 brand names.Changes in the list that have been authorized to June 30, 1939, placed 56 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Fifty-seven permissible explosives were transferred from the active to the inactive list. The brand names of four explosives were rescinded curing the year. The present list contains 18G brand names. The brand names of the Permissible explosives placed on the active list are as follows:"

Sep 1, 1939