Search Documents

By G. A. Crowder

Far infrared spectra, most of them in the region 15-200 microns and for both the liquid or solution state and for the vapor state, were obtained for twenty-seven compounds.

Jan 1, 1965

By D. A. Reynolds

The Bureau of Mines-American Gas Association survey of the carbonizing properties of American coals was begun in 1929, and has been continued almost without interruption since that time. Upwards of 100 coals have been carbonized at low, medium, and high temperatures in this survey, and about 200 additional coals have been carbonized at high temperatures only. All survey coals were blended with coal of different rank for carbonization at one high temperature (900° C,). During the past few years, 12-high-volatile A coals were blended with Pocahontas No 3 coal from Kimball, McDowell County, W. Va., and in this report the physical properties of the cokes from these high-volatile coals and their blends are compared.

Jan 1, 1949

By C. W. Owings, L. D. Tracy

"IntroductionMany bituminous coal-mining companies have inaugurated extensive safety Programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania.Story of the ExplosionAt about 10 o'clock on the night of the explosion an examination was made in No 2 butt left and parallel off 7o. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of Po. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 18 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air an explosion occurred.The helper dropped to the floor and was burned about the face and wrists. The machine operator ran down the entry and was more severely burned about the face, neck, and arms. He later developed pneumonia and died. Both men reached the door in the chute between No. 14 and No. 15 north. A pumper, who had felt the rush of air, found the men and helped them to walk outside."

May 1, 1927

Apply state-of-the-art monitoring and computer systems technology to remotely monitor geostructural data and evaluate ground conditions in near real-time. Background Recently, the coal mining industry has progressed dramatically from a labor-intensive industry to highly mechanized and automated systems achieving significantly higher production rates. In underground longwall coal mines, production and face advance rates have increased by almost tenfold in the last 15 to 20 years. With increasingly high advance rates, geologic anomalies which affect rock mass quality are encountered more frequently, far exceeding the current rate at which ground control information can be processed and analyzed. As a result, mine operators find themselves with insufficient time or resources to cope with the rapidly changing ground conditions. To keep up with the technological advancement in mining and the associated ground control problems, the Bureau of Mines is conducting a multi-phase research pro¬gram to implement a computer-assisted Ground Control Management System (GCMS). Research is ongoing at present, but when completed the system will be designed to 1) monitor and evaluate data on rock properties, geologic conditions, and rock mechanics data from underground sensors in near real-time; 2) interpret the analyses to evaluate the interaction between various critical ground control parameters; 3) assess the structural integrity of the mine; and 4) determine failure modes and provide recommendations for control measures, design modifica¬tions, and alternative support procedures. The system will be expanded into its full capability during various phases of this research program.

Jan 1, 1991

By Bruce I. Thomas

The occurrence of tin-bearing gravels along Tozimoran Creek in central Alaska has been known for a number of years. In September 1944 the Bureau of Mines investigated an area approximately 1,000 feet long and 200 feet wide along Tozimoran Creek to deter-mine the cassiterite content of the stream gravels, which are about 4 feet deep and covered by 3 feet of overburden. Nine trenches and two shafts were excavated, from which samples of the underlying gravels were taken. This report contains a discussion of sampling methods and tables giving the results of analyses.

Jan 1, 1948

By Robert L. Rough, William E. Eckard

Laboratory data obtained from a Bureau of Mines rotary air core of a well near Sugar Grove , Warren County , Pa . , were instrumental in initiating hydraulic fracturing in the area to stimulate oil recovery from Glade sand oil reservoirs . This report outlines the general geology , lease development , reservoir- rock characteristics , and oil - production history of Glade and Clarendon sand reservoirs in Warren County . The methods of well completion for single- stage and multiple- stage hydraulic fracturing of old and new wells are discussed , and a range of hydraulic fracture treatment data from 29 Glade sand and 10 Clarendon sand wells is presented . A composite decline curve representing oil - production data from six wells shows probable results of hydraulic fracturing . Average cumulative oil production during the first 100 days after hydraulic fracturing with a sand - carrying liquid is compared with production after conventional shooting with liquid nitroglycerin .

Jan 1, 1964

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics of positive corona are presented for air in a 2 - in - diam electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig . Results show that current - voltage relationships depend solely on air density . Comparison of data on positive corona with previously published data on negative corona demonstrates a higher sparkover voltage and a wider range of operability for positive corona at temperatures above 375 ° F. The possibility of achieving higher voltages with positive polarity as indicated by these experiments implies several advantages for the use of positive corona in precipitators to allow better removal of suspended material from hot gases . Based on the physics of an ion in an electrical field , a theoretical equation is derived to define current - voltage characteristics of positive corona in terms of air density . Constants for the equation are evaluated from Calculated current - voltage values at different air densities agree reasonably well with experimental data .

Jan 1, 1964

By W. T. Benson

In May l942, the Bureau of Mines started exploring for manganese on the Black Poch manganese property, Esmeralda County, Nev., to determine possible reserves of manganese in the deposits. The work was done by the Bureau in cooperation with the Federal Geological Survey and comprised a study of the geology, mapping the area, and exploring by trenching, test pitting, and sampling. All ore bodies were examined and sampled, and the three most important areas were explored by trenching and test pitting. This report notes the location, ownership, and history of the deposits; explains the physical features of the district; mentions briefly mine workings and metallurgy; and describes the geology and ore bodies. The Bureau erected a temporary camp, repaired 5 miles of temporary road, constructed 1,000 feet of new road, dug 3,173 foot of trenches with a vertical crone section of 4 x 10 feet and 91 test pits with a cross section 3 x 6 feet, averaging about 6 feet deep, and cut 134 samples.

Jan 1, 1950

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the 'indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By A. L. Engel

A representative sample of gold-silver ore from the Keystone Mine, Manhattan, Nye County, Nev., was submitted for these tests. The ore was an altered diorite rock with very small amounts of sulfide minerals of copper, lead, zinc, antimony, and arsenic disseminated in fine grains throughout. As indicated by test results, much of the silver content of the ore apparently was associated with these sulfide minerals. The gold probably occurred with iron oxides in the ore. Assays showed 0.16 ounce of gold and 2.8 ounces of silver per ton of ore. This investigation was made to study application of activated carbon in the cyanidation treatment of the ore. The treatment proposed for u.se at the mill is as follows: The ore is crushed to minus-10-mesh size and separated into plus -and minus-65-mesh portions. The minus-10, plus 65-mesh sands are cyanided by leaching and the minus -65-mesh slimes by agitating. After 48 hours of agitation the slime pulp is thickened to about 1:1 water:solid ratio, and part of the pregnant solution is recovered. The pulp is then diluted to a 2:1 ratio, and the remaining dissolved values are extracted with the activated carbon. The barren pulp then can be discarded. This procedure eliminates the necessity for further washing the slime pulp and also recovers most of the excess sodium cyanide required for extracting the optimum amount of silver from this portion of the ore.

Jan 1, 1951

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or y blasting device enumerated in the permissible Lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1941

[In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or a blasting device enumerated in the permissible lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.]

Jan 1, 1941

By D. E. Fogelson

In a factorial experiment, blasting caps were detonated in three sizes of shotholes in mortar with three types of stemming--dry sand, wet sand, and hydrostone. Free-surface displacement pulses were recorded with a capacitive-displacement gage at a distance of 15 inches. The effects of decoupling and the type of stemming on the amplitude and the duration of the displacement pulse were determined. Both the amplitude and the duration of the displacement pulse were significantly decreased by increasing the decoupling, but they were little affected by the type of stemming.

Jan 1, 1965

By David M. Hyman

Outbursts are sudden and violent releases of gas and coal that result from a complex function of geology, stress regime, and gas pressure and content. The Bureau of Mines has reviewed methods for prediction and mitigation of such outbursts in use worldwide, as an aid in selecting the proper techniques for use in specific mine environments. Outburst-prone coal may be distinguished from normal coal by its sorption-desorption velocity. Three types of methods used to characterize the kinetics of sorption-desorption are described; all are based on the ability of outburst-prone coal to release, through desorption, methane or carbon dioxide much more rapidly than normal coals. Other prediction methods, based on borehole samples, are also described. Various mitigation methods described and evaluated include (1) working the least stressed, less disturbed, lowest gas content seam in multiple-seam areas; (2) mine opening geometry; (3) inducer shot firing; (4) water infusion; (5) localized stress relief, using boreholes or by cutting a reliever slot in the longwall face; and (6) other gas drainage methods.

Jan 1, 1987

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX G TABLE IX MINE A 1 General Total Employees 3000 Maximum No, of Men Underground/Shift 800 Shifts/Day 3 Type of Ore Copper Daily Production (TPD) 25,000 Mining Method Room and Pillar Vein Dip/Thickness l0°/l5 ft Number of Levels/Max Depth 1/0 to 1800 ft 2 Haulage, Conveyances and Travelway Main Haulage Rubber Tire/10 miles belts Man-Ways - Typical Route of Travel to most Remote Sites Rubber Tired Vehicles Hoists - Capacity/Speed/Depth Depth under construction 3 Ventilation 2,500,000 cfm - 5 surface fans 4 Compressed Air N/A cfm 10" and 12" lines 5 Incendiary Storage 2 day powder 1000 gal fuel oil 6 Communications 1 complete system - all shops, dinner areas, and feeder/breaker stations 2 partial systems 7 Escapeway- Systems Man Check System Section boss log and punch cards Alarm System Mine phones with paging system Posting of Escape Route Maps No Escape Signs Every intersection, fluorescent paint Evacuation Drills 2/yr/shift Refuge Chambers - 1 cinder block - No longer required

Jan 1, 1976

By E. C. Lane

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of 16 California crude oils. Analyses of other oil from California have been published in Reports of Investigations 25954/, 26085/, 28466/, and 30747/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of the samples vas facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1937

By E. C. Lane

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of 16 California crude oils. Analyses of other oil from California have been published in Reports of Investigations 25954/, 26085/ 28466/, and 30747/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of the samples vas facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1937

By Russell R. Trengove

The Strawberry tungsten mine is in the Jackass Mining District, in an isolated portion of eastern Madera County, near the southeast corner of the Yosemite National Park. The deposit was discovered in 1941, and production started in 1943 when the mill was completed. With the exception of 1946 and 1947, production has been continuous. The area in the vicinity of the mine is granite containing islands of sedimentary beds highly altered by metamorphism that resulted from the intrusion of acid igneous rock. Schoelite occurs in almost vertical lenses of tactite between the limestone and the granite.

Jan 1, 1949

Data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 889 underground (6.0%) and 13,982 surface (94.0%) mining operations.1

Aug 1, 2009

By ALICE V. Petar

Like many gem materials, amber has a colorful history which may be traced through the writings of the ancients and the ornamental relics discovered from time to time. Like few gem materials, however, it is distinctly useful in products whose value has no connection with the gem industry. Long prized for its beauty, amber was fashioned into articles of jewelry and ornaments to please the fancy of ancient rulers and to find a place among treasured pos- sessions in their tombs; it has been used by adherents of various creeds for rosaries and other religious symbols; and although still sold for these pur- poses it also lends itself to such commercial purposes as raw material for varnish. Amber is only on the border-line of the mineral kingdom; actually it is of vegetable origin, having been formed as resin from trees of the conifer family that existed during the Tertiary period. It is the hardest of the fos- sil gums. The United States produces no amber, although a few occurrences are known. Most of the world's supply comes from East Prussia, where it is ob- tained from both land and sea. For many years pieces of amber were gathered from the Baltic by fishermen and deep-sea divers; and although about 10 per- cent of the Prussian amber is still recovered from the sea, most of the out- put is mined from open pits on the Samland Peninsula.

Jun 1, 1934