Search Documents

By R. C. Hickman

"INTRODUCTION The largest known deposits of ilmenite and rutile in Virginia are in Amherst and Nelson Counties. Other deposits occur in the State, but their extent is not known. One of the most promising of the latter is the deposit in Roanoke County on the T. M. Bush and the H. L. Hutchins property near Roanoke. A geophysical survey was made of the deposit, followed by core drilling. In April and May 1946, four holes were drilled, totaling 822 linear feet.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch,. Bureau of Mines."

Aug 1, 1947

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station of the Bureau of Mines have shown that satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but also upon the kind

Jan 1, 1945

By E. R. Maize, R. D. Currie

"Good ventilation is one of the first requisites in the safe and efficient operation of a coal mine. If a mine is gassy, the uninterrupted circulation of an adequate supply of fresh air is imperative if that mine is to operate with a relative degree of safety. That ventilation is not •only a safety consideration, but is an extremely important economic factor is shown by the fact that in many mines 50 per cent of the total power cost is for ventilation.The system used in the Graceton Coal & Coke Co. mine, Graceton, Pa., is believed to be unusual in many ways. Its application in this mine has re¬sulted in good ventilation of the working faces, no interruption to the venti¬lating current through the use of doors. a large- portion of the air circulated by the fan reaching the working places, low velocity air currents on traveling and haulage ways, low water gage and power consumption of the fan, and well-ventilated gob areas.This investigation was made possible through the courtesy of W. H. Robertson, mine superintendent. Fred Roberts, mining engineer, and Floyd Phillippi, mine foreman, assisted in the collection of information.The Graceton mine is a slope, opening the Upper Freeport or E bed, on the Pennsylvania Railroad about midway between Blairsville and Indiana at Graceton, Indiana County, Pa. The production is approximately 1,000 tons of coal per day and about 170 men are employed underground. The mine is considered gassy and was found to be liberating approximately 300,000 cubic feet of methane in 24 hours. The return airways terminate at a circular, concrete lined shaft 12 feet in diameter and about 115 feet deep at which is the exhaust fan.Mining is done by a block system with flat or level entries turned off the main slope at intervals of 1,350 feet, off which the butt headings are turned up the grade parallel to the slope. Rooms, which are about 225 feet long and 12 feet wide, are turned off the butt headings on 80-foot centers, leaving a block about 68 feet thick between rooms.Haulage on the main slope is by rope, with the hoist on the surface. This hoist is electrically driven through a 500-h.p., 2,300-volt motor. The rope used in this haulage is 1-1/8 inches in diameter. There are five electric trolley locomotives - one 10-ton and four 6-ton - which do all of the hauling in the flat and butt entries.Before it is blasted all of the solid coal and as much of the pillar coal as can be cut with safety is undercut by permissible mining machines. Shooting is done by shot firers who use permissible explosives, electric detonators, and dry-cell, nonpermissible batteries.In rooms where conditions are normal, timbering consists of two rows of posts on 4-foot centers. Posts are required to be within 6 feet of the face in machine-cut places and within 3 feet of the face in hand-mined places. Timbering on entries, where required, is of two types: a bar hitched into the ribs and supported by the coal, or 3-piece sets. The legs of the 3- piece sets used on the slope are set well back into the rib to prevent their being. knocked out by a wreck."

May 1, 1932

By J. Drew Potts

The U.S. Bureau of Mines identified respirable dust sources and controls on four continuous auger mining sections, two with relatively low dust levels and two with high levels. Factors adversely affecting dust levels included auger equipment design, continuous haulage, and low seam height. Dust controls included ventilation practices and spray systems. Maximizing airflow seemed to reduce dust levels most. Air leakage and shock loss can be reduced by constructing stoppings with brushed-on mortar containing fiberglass and by keeping areas between curtains and ribs free from obstructions and storing equipment not essential for face activities in outby crosscuts. Curtain configuration, setback distance, and installation can also affect dust levels. Use of both blowing and exhausting curtains is the most effective configuration. Setbacks from the face should not exceed 15 ft. Installing brattice curtains at least 5.5 ft from ribs, when entries are 26 ft wide, minimizes velocity head. Installing curtains tightly against the mine roof and floor helps maintain a forward airflow movement in the center of the mine heading; curtain overlap can create a tighter seal. The wet-auger spray system also effectively controls dust, provided the mine is already exercising good ventilation practices.

Jan 1, 1989

By Robert W. Smith

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy, facilitating the theoretical study of flame and combustion phenomena. This report is the fourth of a series4/ presenting results of the study for particular fuel-oxidant systems. These calculations have as their objective the evaluation of the constant pressure flame temperatures of methane-air, propane-air, and ethylene-air mixtures for a range of pressures.

Jan 1, 1953

By A. L. Pierce

This paper describing the mining practice at the Spring Hill mine of the Montana Mines Corporation, Helena, Mont., is one of a series issued by the Bureau of Mines on mining methods and costs in various districts. Its purpose is to summarize improved methods whereby lower costs have recently been obtained. These improvements are principally the adoption of a modified sublevel stoping method of mining the use of grizzlies underground improvements in haulage, and rage bonuses. The Sprint Hill, Trine is situated in Grizzly Gulch, 3 miles southwest of the city of Helena. Helena is on the links of the Northern Pacific and the Great Northern Railways; and the East Helena smelter of the American Smelting and Refining Co. to which the concentrates from the mine are shipped, is but 6 miles east of Helena. The mine is probing 150 to 200 tons of gold ore per day, with an underground crew of about 40 men.

Jan 1, 1931

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By Frank E. Cash, Max S. Petersen

"INTRODUCTION Explosives have been used in ever—increasing amounts since gunpowder was invented. For hundreds of years only low explosives of the deflagrating type were used, and they were fired by means of a flame or hot object. Ben¬jamin Franklin first ignited gunpowder from a distance in 1751 by means of an electrostatic spark. Further efforts to develop a satisfactory electrical method to ignite explosives from greater distances were overshadowed by the invention of safety fuse in 1831, as this offered a relatively simple and inexpensive means of firing explosives.The discovery and introduction of high explosives of the detonating type and the invention of the fulmitate of mercury blasting cap about the middle of the nineteenth century provided the needed impetus for inventors to develop means of firing the cap by electricity. The original high-tension igniter, following Benjamin Franklin's experiment in which the detonating compound was ignited by a spark, was discarded in favor of a low-tension igniter, in which the detonating compound was ignited by a heated wire. The past 2 decades have seen considerable improvement in the design and construction of electric detonators to make them safer and more efficient, yet in spite of the improvement it is estimated that less than 50 percent of the explosives used in industry today are ignited or detonated electrically. The trend, however, is toward the use of electric methods. In recent years numerous-mining companies have introduced electric blasting exclusively at their mines as a means of improving safety and efficiency."

Sep 1, 1946

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By M. Hayashi

The Bureau of Mines conducted laboratory studies on low-grade vanadiferous silicates from the Pumpkin Buttes and Nine Mile Lake deposits of Wyoming to examine techniques for extracting vanadium and uranium. Recovery from low-grade sources such as these could contribute to future vanadium production and reduce reliance on vanadium imports. The Pumpkin Buttes samples contained 0.03 to 0.04 pct V205 and 0.06 to 0.12 pct U308; the Nine Mile Lake samples contained 0.02 to 1.0 pct V205 and 0.06 to 0.19 pct U308" Leaching the Pumpkin Buttes samples for 18 h at 800 C with addition of 200 lb/ton H2S04 resulted in recoverey of 80 pct of the vanadium contained in the samples. The Nine Mile Lake samples were readily leached, yielding 78 to 94 pct of the vanadium after 3 h at 800 C with addition of 100 lb/ton H2S04, A solvent extraction procedure was used to selectively recover urani-um from Pumpkin Buttes and Nine Mile Lake leach solutions and to recover vanadium from the raffinates. In batch shakeout tests, Alamine 336 recovered over 95 pct of the uranium from leach solution adjusted to pH 1. Di-2-ethylhexyl phosphoric acid and Cyanex 272 recovered vanadium from the uranium raffinate after reduction and adjustment to pH 2; vanadium extractions of up to 96 pet and 92 pct, respectively, were achieved.

Jan 1, 1985

By T. A. Henrie, D. C. Fleck, D. G. Kesterke

Uranium metal was electrowon from uranium dioxide dissolved in fluoride melts . The UO₂ was fed directly to the cell in a continuous manner . Electrolysis was performed at 1 , 200 ° to 1,300 ° C in electrolytes composed of UF4 , LiF , and BaFa . A single regulus of metal was collected in a confined area of the crucible . Product purity of 99.8 percent was attained . Carbon was the major contaminant . Compartmented cells were studied as a means of confining the oxide feed to the vicinity of the anodes .

Jan 1, 1964

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and2-year time periods during 1990–1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 9, 2004

By Robert A. Jankowski

The U.S. Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the mining industry, has identified and demonstrated the effectiveness of several improved face ventilation techniques for longwall mining systems. These include the following: identifying improved techniques for measuring face ventilation parameters on longwall sections, installing curtains at the intake end of the longwall face to maximize usage of the primary airflow, identifying optimum face airflow rates for maximizing dilution effects, and coursing the primary face intake from tailgate to headgate to minimize outby airflow contamination. Application of these techniques throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1993

By J. F. Shaw

MINE fires are usually extinguished by constructing seals in the approaches to the areas to exclude air from the fire areas, which smothers the fires in an oxygen-depleted atmosphere. Seals should be substantially constructed and made as nearly airtight as possible and should be provided with a sampling pipe so that samples of the atmospheres behind the seals may be collected at regular intervals. Methods of constructing seals and of sampling and analysing mine atmospheres are fully described in Bureau of Mines publications. (1, 2). Information obtained on the composition of atmospheres behind fire seals is helpful in determining if a fire has been extinguished or if there is any danger of an explosion when a fire area is being sealed or unsealed. The progress of a mine fire can best be determined by studying percentages of carbon dioxide, carbon monoxide, and hydrogen in the atmosphere behind the seals. Hydrogen will be formed in a bituminous- or subbituminous-coal mine when the temperature exceeds 480° F. and in an anthracite mine when the temperature exceeds 660° F. (3). Carbon monoxide and carbon dioxide are both products of combustion of coal, wood, or other organic compounds. The presence of carbon monoxide has long been accepted as an indication of a mine fire. A sealed fire area should not be reopened until the carbon monoxide has disappeared. Trends in the percentage of carbon dioxide are also useful in determining the status of a mine fire. Carbon dioxide is sometimes liberated by rock strata. In this case, carbon dioxide in the atmosphere behind a seal will be from two sources-the rock strata and the fire. When the, fire is extinguished, carbon dioxide will be liberated from only I source, the rock strata, and when the percentages of carbon dioxide are plotted, the slope of the curve will not be as steep as when this gas was being liberated from 2 sources. If the only source is the fire, the percentages of carbon dioxide will gradually decrease after the fire has been extinguished. By studying analyses of a mine-fire atmosphere, it is possible to determine if the atmosphere is explosive; if the mixture is capable of becoming explosive when mixed with air; and if the mixture can be made nonexplosive or be prevented from becoming explosive by being mixed with an inert gas. These factors can be computed mathematically or determined graphically. The mathematical calculations advanced by Ash and Felegy (7) are discussed, and graphical solutions of their equations are presented. It is believed that the graphical solution will be extremely helpful in determining the characteristics of a mine-fire atmosphere when fighting a fire, because the results can be obtained in a matter of minutes, and there is less likelihood of an error being made under the stress incident to control efforts. The experimental and theoretical work upon which the formulas are based have been adequately described and are not discussed at this time (5) (6).

Jan 1, 1955

By W. W. Graff

This paper describing the mining practice at Mine No. 5 of the Marquette range, Michigan, is one of a series being prepared by the Bureau of Mines on mining practices, methods, tend costs in the various mining districts of the United States. The top-slicing system of mining, has been used ever since the present operating company took control of the property in 1903, the main level and sublevel layout being chanced only as local conditions required and the use of mechanical equipment increased.

Jan 1, 1930

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By T. M. Garland

A nomographical approach is proposed as a fast, easy-to-use, and reason- ably accurate method for estimating expected discounted cash flow (DCF) rate of return and payout time for onshore development drilling and oil production. All costs pertaining to drilling, completing, and equipping development wells, annual expenses of operation, maintenance, and taxes incurred in producing properties, and crude oil prices were considered in developing the nomographs. This report briefly outlines the origin, derivation, and use of the nomographs.

Jan 1, 1973

By H. D. Hess

This report describes in detail a unique occurrence of fersmite, (Ca, Ce, Na) (Cb, Ti, Fe, Al)2 (0, OH, F)6, which occurs as small anhedral inclusions and intergrowths with a tantalum-free columbite found in the metamorphic complexes of Ravalli County, Mont. Chemical and crystallographic data along with the physical and optical properties agree in general with those given in the original description of fersmite from the Ural Mountains of Russia. X-ray diffraction data not given in the original description and more specific optical data have been determined. The Montana fersmite, now established as the second occurrence of this rare calcium-columbate mineral, was discovered during a routine Bureau of Mines mineralogical examination of a prospector's sample.

Jan 1, 1960

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008