Search Documents

By R. C. Anderberg, F. J. Caervenyak, F. J. Frattali, H. J. Kandiner, R. A. Brown

"INTRODUCTION Considerable interest was shown .prior to and during World War II in the winning of metallurgical-grade alumina from anorthosite, kaolin, siliceous bauxites, diasporic clays, and other aluminum-bearing ores. Laboratory and pilot-plant investigations were made on many of these ores by the Bureau of Mines, and a series of reports on them is being prepared. This report covers the tests made on the application of the lime-soda-sinter process to anorthosite, which is a mixture of albite, NaAlS1308, and anorthite, CaAl2Si208. Extensive deposits of anorthosite occur in the Laramie Range in Wyoming and extend into Colorado; other deposits are found in New York, with outcroppings appearing in Vermont, Maine, and Labrador.Anorthosito can not be treated by the Bayer process for the production of metallurgical-grade alumina, because excessive losses of soda and alumina occur from the formation of sodium-aluminum silicate due to the large amount (50 percent) of silica in the ore.RESULTS OF INVESTIGATIONSSmall-scale laboratory tests supplemented by pilot-plant runs have demonstrated that the alunina and soda occurring in the Wyoming anorthosite from the Laramie Range can be extracted and recovered satisfactorily by the lime-soda process. It has been shown that liquors containing approximately 95 gram of A1203 per liter can be consistently produced at Na20:A1203 ratios from 1.75 to 2.27, and that these liquors can readily be desilicated and carbonated to yield high-grade alumina trihydrate of quality comparable to that essential for cell-grade alumina. The optimum results were obtained with Na20:A1203 mol ratio of 1.03 and Ca0:Si02 ratio of 2.14 in the sinter when calcined at an average temperature of 2,444ºF. for 25 minutes."

Nov 1, 1947

By Gary W. Krantz

Fibered, portland-cement-based gunite products were applied in the Bureau of Mines Lake Lynn Laboratory Experimental Mine using a variety of pneumatic guns and gunning crews, The demonstrated wet-mix (with silica fume), dry-mix, and surface bonding products were sampled by the Bureau and subjected to a suite of engineering analyses. Gunite flexural and compressive strength, rebound, permeability, porosity, dust loading, shooting rate, crew requirements, and cost factors were evaluated. Steel, fiberglass, or polypropylene fibers were contained in all but two of the gunires tested. Both Bureau and private testing laboratory analyses are provided for some products. Electron probe micro-analysis and X-ray diffraction analysis were performed on the silica fume fraction of the wet-mix gunite to characterize the dust. Aggregate size fraction distribution analyses were performed to provide strength relationships. Results indicate that all of the commercially available fibered-gunite materials tested can provide beneficial sealant, spall prevention, or roof stability control attributes for underground mining environments when applied by an experienced crew using a well-maintained gun, in accordance with product manufacturers' recommendations and when used for the designated purpose.

Jan 1, 1984

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking in the past few years have focused the attention of the Bureau of Mines on the need for safety standards for such operations. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1957

By D. J. Parker

The oft-repeated expression that the taproot of safety lies in the attitude of the management toward accident-prevention work is indisputable and has become almost an axiom. Trite and somewhat timeworn though the statement may be, it is nevertheless true that the supervisory force must earnestly support a policy of safety and maintain at all times a con¬ siderate regard for the welfare of the employee if that high degree of cooperation of the employee, so vital to the successful prosecution of any safety program, is to be expected. The responsibility for preventing accidents rests upon the management, and in the case of the Spring Canyon Coal Co. such responsibility is recognized and accepted with little or no reservation. This company, aside from the humanitarian aspects involved, believes that safety is good business and not a matter to be treated passively or in a perfunctory manner. The problems with respect to safety that have been met and wholly or partly solved can best be appreciated when some of the natural conditions, adverse and otherwise, existing at this operation are taken into consideration. Mine 1 is about 1 mile north of the town of Spring Canyon, Carbon County, Utah, and is served by both the Denver & Rio Grande Western and Utah Coal Route railways. During the year 1931 the mine produced 312,397 tons, approximately 10 per cent being derived from pillar workings. The normal daily output during the summer months is about 2,000 tons, and during the peak of production in the winter season the daily production varies from 2,500 to 3,000 tons. The number of miners varies from 87 in summer to 220 in winter, and the day men vary in number from 66 in the winter to 45 in the summer; 12 company men are employed the year around. The officers of the company are J. B. Smith, president, San Francisco, California; T. R. Stockett, general manager, Salt Lake City; and G. A. Murphy, superintendent, David Brown, assistant superintendent, and John Sullivan, mine foreman, all of Spring Canyon, Utah.

Dec 1, 1932

By John Dixon

This paper is one of a series on milling methods and costs being published by the Bureau of Mines. Acknowledgment is made to J. B. Tyrrell, managing director, and Wm. Sixt, manager of the Kirkland Lake Gold Mines, for permission to publish this article. The Kirkland Lake Geld Mining Co.'s mill is located on Government Road at the west end of the productive part of the Kirkland Lake mining area, 1 mile west of the village of Kirkland Lake. The crushing plant is connected to the shaft house of No. 2 shaft, which is now the only operating shaft.

Jan 1, 1931

By Brian G. White

Two examples of en echelon mining-induced fractures seen in hard-rock mines provided a basis for inferring that fracture zones and bedding plane separations immediately surrounding mine openings are promoted by oblique shear into the openings. It is hypothesized that initial fractures or separations form at the corners of openings as a result of high stress and physical constraint on the rock's ability to deform elastically toward the opening. These conditions result in a locally preferred direction of shearing. The shearing, in turn, generates tensile stress that initiates a progression of systematically offset fractures approximately parallel to the direction of greatest compressive stress. The fractures or bedding separations create tabular rock layers that amplify shearing displacement through bending and dilation. Such shearing effectively reduces and redistributes the compressive stress, but significant dilation is an inevitable consequence. The combination of dilation and shearing and the progressive development of fracture zones have important implications with respect to ground support. The concept of mining-induced fractures forming as a result of shear is illustrated by two examples from coal mines. First, fractures seen at longwall faces probably result from shear associated with subsidence. The fracture zone that develops approximates or possibly defines the draw angle of subsidence. As the face advances, fractures extend downward along the lower edge of the fracture zone, while upper extensions of the fractures are pressed closed. Fracture zones in entry roofs provide a second practical example. Here, mining-induced fractures typically follow bedding planes. The shear zone model suggests that the first bedding separations develop near the edges of the roof and successive separations progress upward and toward the center. However, if the direction of greatest stress is inclined with respect to the roof, a fracture or bedding separation zone may propagate from one side only and also extend higher. Because coal ahead of the face provides some support against lateral shear deformation, bedding separation is inhibited near the face. Rock bolts installed close to the face ultimately become more strained and bent than bolts installed a few meters from the face, and bolts installed through the more remote part of a separation zone may ultimately experience the greatest tensile and bending strains. This model is supported by field data documenting progressive bolt failures that rapidly propagated downward across the roof during face advance.

By H. B. Brunot

The United States Bureau of Mines under provisions of Schedule 2C4 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equipment and make up permissible units by assembling them. Before the assembler purchases electrical accessories for use in such contemplated units he may require certain information from the accessory manufacturer as to whether the particular accessories are suitable for assembly in his proposed permissible outfit. To aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies.

Jan 1, 1935

By L. J. Kane

Chemical processes using coal often require economical removal of dust from high-temperature gases. Laboratory-scale investigations by the Federal Bureau of Mines have shown that an aluminum silicate fiber is suitable for filtering dust from gases at 1,800° F. The effects of the bulk density of the filter, rate of gas-flow, concentration of dust in the filter, fiber diameter, depth of filter, and concentration of dust in the feed gas on removal efficiency, pressure drop, and capacity of the filter to hold dust were studied. The laboratory filters were difficult to construct because the fibers were longer than the tube diameter. This caused irregular distribution of fiber that permitted dust-laden gases to leak through channels developed in the filter. Leaks also formed between the filter and the tube wall, but this was minimized by improved filter design. However, edge leaks and leaks through channels in the filter probably would be insignificant in properly constructed filters of industrial size. As the concentration of dust in the filter increased, the efficiency of the low-density filters decreased, contrary to expectations, probably because a higher percentage of the dust passed through channels that developed in the filter. The efficiency of high-density filters, however, increased with the concentration of dust in the filter. Results indicate that loosely packed filters would have a longer life than tightly packed filters at the expense of efficiency. As regeneration or replacement of stationary filters is difficult and expensive, loose filters would be best for filtering gases containing much dust. Gases containing little dust may be cleaned with tightly packed filters to obtain higher efficiency. For either type of filter, precleaning with cyclone separators or other means is advisable.

Jan 1, 1960

By Donna D. Harbuck

The Bureau of Mines has investigated a process to produce titanium powder directly from titanium salts. If successful, such a process could lower the cost and increase the use of titanium. In this study, K2TiF6, K2TiF3, and TiF3 were reduced with potassium in the temperature range of 650° to 750° C. Under certain conditions, titanium powder 1.6 to 3.3 microns in size was produced. After leaching the product with a 0.1M HCl solution, powder impurities as low as 0.04 pct potassium and 0.28 pct fluorine were obtained. However, oxygen levels of over 1 pct and the frequent formation of insoluble byproducts demonstrate the need for further research to make the powder suitable for powder metallurgy applications.

Jan 1, 2011

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part 1 of the report contains the results of the field tests. The studies were made on an oil lease in a so-called "sour district," near Borger, Tex., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field test proved that aluminum lease tanks will withstand corrosion by hydrosulphide, but it as found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By William A. Beck

"The Old Cline mine, also known as the Old Cruse mine, was first worked for gold in1895. The property was opened by several shafts and trenches; and some stoping has been done, producing several cars of copper-gold ore in the early nineteen hundreds. Chalcopyrite is visible in selected samples; and, with the aid of a mineralite, several samples showing a considerable amount of scheelite were found on the old waste dumps.The mine is in Township 6, Cabarrus County, N. C., 5 miles north of the village of Mount Pleasant, 10 miles northeast of Concord, and about one-half mile south of Watts Crossroads. It is one-fourth mile east of the county road.When examined, the property was owned by H. F. Tompkinson, Concord, N. C., and was leased, with option to buy, by L. Nash. Titles of record were not investigated.As stated above, the Cline mine was first worked in 1895. The property was Purchased in 1902 by J. A. Clark and A. A. Smith of Atlanta, Ga., and worked for gold and copper. No record is available of the quantity of ore removed during these operations.A Bureau of Mines mining engineer3/ examined the mine as, a copper prospect on October 13, 1944.The Cline mine is in an area characterized by flat to rolling topography, dissected by many streams and rivers. It lies in the Piedmont Plateau and Varies in elevation from 700 feet to 800 feet. The surrounding country is partly wooded and partly cleared farm land.A quartz vein occurs in country rock of quartzite and greenstone.4./ The ore occurs in a series of quartz lenses, having a width of 1 to 3 feet and dipping about 750 NE, and striking N. 300 W. All these lenses have fairly sharp boundaries and in some cases are entirely separated from each other, while at other times they are connected by thin stringers of quartz. They can be traced for 1,000 to 1,200 feet by a series of shafts and test pits."

Apr 1, 1946

By G. E. MeGlelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores. This technology has been adopted on a broad scale by the precious-metal-processing industry. This report presents information on the application of agglomeration technology to finely ground precious-metal-bearing tailings. Two commercial operations that have benefited from agglomeration technology are discussed. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1985

The performance of two large-capacity ventilation systems was compared through tests conducted in a large dead-end heading at a pilot oil shale mine in Colorado. Sulfur hexafluoride (SF6) tracer gas was used to measure the performance of the two systems: a free-standing jet fan and a reversible fan with rigid duct. The tracer gas was used to simulate the production of mine air pollut-ants, including blasting pollutants, hot diesel emissions, free methane from surrounding strata, and methane desorbing from muck piles. The test room was 55 ft wide, 30 ft high, and 320 ft long. The performance of the two fans was similar, but the jet fan used less power. The tests showed that either system could provide effective ventilation during oil shale mining.

Jan 1, 1986

By R. G. Meara, O&apos

[P.F? bmit e-ninirq ir.3.l r;tq: in the Znited State :; was u~irlyortant p~ior to the Torld ;Jar, ?-.lt with the c~r,sxti~rl of imports d11rln.c thr World 'Jar tke Rmericnn mar~factu~er:. of 1itkopone mcl Sayiun c;~oai?als forced tile tl~veloor?.ent of domertic bar,i$e dqosit9. Pr%~~,n-ily bcca-lse of tho increasing dc.n;;nl'i for lit,hupone3 by the pr?i:~t, Tlocr-covcrin~;, ,md rt1tbe.r indl~stries, ~3c.vs1o~:rnc2t of cto~entic de~onits has cr~ntim~ed to c-cpand. 13 1914, the salnr! oC doxegtic c~l~.dt? t,m-it~ ;u~cr-~nteii. to 52,91? tons, in 1237 ???,1!.1 tons nmre so1.d; thc 12:t~r rcyrprcntcd 77 .E;T pmccnt of the tot,:rl, dr??;ectic and imortcd., haritd US~C in the Cnited State? di7rinz t,hat :.vXr. C,f +he total 193,3:& ton? coy.1~-ed in the United 4 Steter ir. 135, 3E.X percent v;as usec? as groi.z.ld ~rai.te? , "0.3 percent arr lithopone, and 17 .:A ].ercc?t in the rnx 11fact,ure of b;~riim chs:nicals . ]

Jan 1, 1938

By R. G. Meara, O&apos

[P.F? bmit e-ninirq ir.3.l r;tq: in the Znited State :; was u~irlyortant p~ior to the Torld ;Jar, ?-.lt with the c~r,sxti~rl of imports d11rln.c thr World 'Jar tke Rmericnn mar~factu~er:. of 1itkopone mcl Sayiun c;~oai?als forced tile tl~veloor?.ent of domertic bar,i$e dqosit9. Pr%~~,n-ily bcca-lse of tho increasing dc.n;;nl'i for lit,hupone3 by the pr?i:~t, Tlocr-covcrin~;, ,md rt1tbe.r indl~stries, ~3c.vs1o~:rnc2t of cto~entic de~onits has cr~ntim~ed to c-cpand. 13 1914, the salnr! oC doxegtic c~l~.dt? t,m-it~ ;u~cr-~nteii. to 52,91? tons, in 1237 ???,1!.1 tons nmre so1.d; thc 12:t~r rcyrprcntcd 77 .E;T pmccnt of the tot,:rl, dr??;ectic and imortcd., haritd US~C in the Cnited State? di7rinz t,hat :.vXr. C,f +he total 193,3:& ton? coy.1~-ed in the United 4 Steter ir. 135, 3E.X percent v;as usec? as groi.z.ld ~rai.te? , "0.3 percent arr lithopone, and 17 .:A ].ercc?t in the rnx 11fact,ure of b;~riim chs:nicals ]

Jan 1, 1938

By E. E. Harton

Bureau of Mines Information Circular 7516, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, was published in October 1949 to aid in estimating investment and operating costs of processes for manufacturing synthetic liquid fuels. Development of such processes by the Bureau of Mines was authorized by Public Law 290, 78th Congress. This bibliography included references to and abstracts of publications appearing from. 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. Bureau of Mines Information Circular 7705, Supplemental Bibliography on Investment and Operating Costs for Chemical and Petroleum Plants, was prepared to cover the area from September 1948 through June 1952.

Jan 1, 1956

By Michael V. Markel

This report summarizes work performed under USBM Contract No. J0100047 revealing the performance characteristics of a composite-type resilient screen deck. The ability of the composite to perform or compete with steel in noise attenuation and longevity was of interest. Tests were conducted at the River King Preparation Plant of Peabody Coal Company. This facility was chosen because it provided parallel process flow and met standard coal cleaning requirements. Comparisons could be made between the adjacent resilient and steel screen decks under similar operating conditions. Noise reductions of 1-6 dBA were realized in the near field. Although the test period did not determine resilient screen life, indications are favorable for their longevity.

Jan 1, 1981

By Joanne L. Johnston

Researchers at the U.S. Bureau of Mines have developed a new technique for bonding strain gauges to rock bolts. These instrumented bolts are used to determine load at intervals along the length of the bolt so that reliable, consistent measurements for the design of support systems can be obtained. In this Information Circular, this technique is described in detail and should result in improved miner safety in underground mines.

Jan 1, 1993

By Robert E. Barieau

General expressions for evaluating various thermodynamic properties applicable to the van der Waals equation of state have been derived. These formulas were subsequently used to evaluate various thermodynamic functions in the two-phase region. The results indicate that, for a van der Waals fluid, there is a finite discontinuity in the second derivative of the vapor pressure curve, in the second derivative of the chemical potential or Gibbs free energy at the critical point, and in the heat capacity at constant volume measured at the critical density. Numerical values are tabulated and graphs are presented for all functions calculated.

Jan 1, 1967