Search Documents

By W. C. McBee

A family of modified-sulfur cements has been developed by the Bureau of Mines for the preparation of construction materials with improved properties. Various types of sulfur cements were prepared by reacting sulfur with mixtures of dicyclopentadiene (DCPD) and oligomers of cyclopentadiene (CPD). Durable cements were prepared with structural characteristics ranging from rigid to flexible. These cements were used to prepare corrosion-resistant materials for use in a wide variety of industrial applications where resistance to acidic and salt conditions is needed. These materials were prepared as rigid concretes, flexible pavings, spray coatings, and grouts. Production of modified-sulfur cements in a commercial-size plant was demonstrated.

Jan 1, 1981

By David C. Oyler

Methane-drainage holes must be completely filled by grout before mining to prevent the emission of large quantities of gas during mine-through, which would constitute an explosion hazard. In November 1980, seven horizontal holes at the multipurpose borehole, a small-diameter shaft drilled as a Bureau of Mines coalbed methane-drainage installation on the property of the Federal No. 2 Mine, Monongalia County, WV, were plugged using a sodium silicate gel grout. This report de- scribes the grout mix and the use of the grout at the multipurpose borehole, and discusses the results observed upon mine-through of the holes in early 1981. Cost data for the sodium silicate grout are also presented.

Jan 1, 1984

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By E. H. Crabtree

This paper, describing the milling practices at the White Bird concentrator, Picher, Okla., is one of a series on milling practices being published by the Bureau of Mines. The concentrator of the White Bird mine, Canam Metals Corporation, is located in almost the geographical center of the present Picher mining cam' in the Tri-State district, one-half mile east of the town of Picher, 1 mile south of the Kansas State line, and about 18 miles west of the Missouri State line.

Jan 1, 1930

By Cloyd M. Smith

Progressive mine management is placing increased emphasis on improved ventilation as a contribution to better safety , health , and productivity of miners . Management is on the alert for means of bettering the working environment by increasing the flow of air and distributing it more effectively to the working places , having in mind the necessity of avoiding exorbitant ventilation costs . A basic need in planning betterments of this kind is knowledge of existing rates of flow and air pressures , infCoorrmmaattiicon that is supplied through ventilation surveys . Some companies make partial surveys from time to time , but few make complete surveys on a routine basis . This report describes the practice of a large British anthracite -mining company , which operates 24 collieries in South Wales , in carrying out a routine program of ventilation surveying . Ventilation characteristics and climatic conditions in the working places of its collieries are determined at frequent intervals with a view to increasing the effectiveness of ventilation and protecting the health of workers . It is thought that many of the points of the procedure used in making the surveys and in compiling and reporting the results will be applicable to American practice and that a discussion of the program may be helpful to colliery managers who are planning similar work .

Oct 1, 1949

By E. G. King

This publication presents original thermal data for a typical variety of perlite and supplies basic information for use in computing energy requirements in processes for expanding perlite. Perlite has been defined by Raiston 4/ as any silicious lava containing dissolved water in sufficient amount to errand into bubbles when the material is quickly heated to a suitable point in the softening range." The uses of expanded perlite in) the construction and ceramic industries have been discussed by Ralston 4/ and King. 5/ The work described here had a dual purpose: (1) It was desired to ascertain quantitatively, using a typical variety of perlite, just how firmly the contained water is held, and (2) it was desired to obtain basic thermal data sufficient for energy-requirement calculations in processes for expanding perlite.

Jan 1, 1948

By J. R. Hauger, P. A. Romans, W. J. Niebuhr

With suitable instrumentation and techniques it is possible to determine the presence of tantalum in columbium to 20 ppm . This paper discusses the selection of X- ray spectrographic instrumentation and describes a technique for accomplishing the low level determination of tantalum . An ion- exchange method of separating tantalum from columbium is also described .

Jan 1, 1964

By H. W. Kilau

The Bureau of Mines used a high-temperature rotational viscometer to test basic oxygen furnace slags to determine fluorspar requirements and to evaluate colemanite and fused boric acid as substitute fluidizers. A continuous technique of viscosity measurement was adapted to better determine the viscosity-temperature profiles of volatile fluorspar slags. Criteria used for estimating slag fluidizer effectiveness were (1) the apparent solidification temperature, and (2) the temperature range of slag crystallization. Colemanite and fused boric acid in high-basicity slag were superior fluidizers to fluorspar when compared on the basis of boron versus fluorine concentration. Fused boric acid was nearly equivalent to ceramic-grade fluorspar when compared on a simple weight basis, while colemanite was inferior to fluorspar. Fluorspar slags volatilized fluorine during viscosity testing. Colemanite and fused boric acid slags were stable, no boron losses being detected. A fluidizing limit was found for fluorspar at 2.9 percent fluorine concentration; higher concentrations impaired viscosity and caused foaming and crusting of slag. Concentrations of boron up to 4.4 percent resulted in very fluid slags with no fluidizing limit.

Jan 1, 1978

By E. M. SEELEY, F. S. LOTT

The total capacity of the natural-gasoline industry to produce light hydrocarbon products increased to 21,322,000 gallons ( 507,670 barrels ) daily on January 1 , 1948 , from 17,928,000 gallons ( 426,860 barrels ) daily on January 1 , 1946. Expansion of the industry in the first two post -war years , 1946 end 1947 , thus averaged 9 percent annually , compared with 6 percent annually in the last two war years , 1944 and 1945 . The number of cycle plants increased only from 37 to 39 in the years 1946 and 1947 , and total capacity of these plants gained 21 percent to 5,857,000 gallons de ily on January 1 , 1948 , represent ing 27.5 percent of the total capacity of the industry , compared with 27.0 percent on January 1 , 1946. All other plants decreased in number in the two-year period from 589 to 510 on January 1 , 1948 , but their total daily capacity increased 18 percent to 15,465,000 gallons . The daily capacity of the average plant in the industry was enlarged from 28,600 gallons on January 1 , 1946 , to 38,800 gallons on January 1 , 1948 , continuing the long -established trend to producing units of greater size and efficiency . The average cycle plant capacity increased from 131,000 gallons daily to 150,200 gallons daily on the same dates as the average capacity of all other natural -gasoline plants increased from 22,200 gallons to 30,300 gallons . Owing to the elimination of small , obsolescent plants in Illinois , Oklahoma , and Pennsylvania , these States experienced the greatest reductions in numbers of plants in 1946 and 1947. In Oklahoma and Texas , several consolidations of two or more plants into a single operating unit were reported . Louisiana and Mississippi were the only States in which the number of plants increased , but daily capacity to produce light products was larger in eleven States on January 1 , 1948, than two years earlier . Added facilities in California and Texas accounted for 41 and 36 percent , respectively, of the national gain in capacity .

Sep 1, 1948

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By G. A. Morrison

Iron ores associated with the Oriskany formation extend from the West Virginia border to the southwestern corner of Virginia. The deposits have been mined at many places, and the district is credited with the production of approximately 13,000,000 tons of ore to 1925, when mining operations ceased (fig. 1). The Oriskany iron-ore deposits occur in the Alleghany Mountains throughout their extent in the State. The name Oriskany was originally given to the limonite ore that was supposed to occur in the Oriskany sand-stone. At present, the name applies to all iron-ore deposits occurring in the lower part of the Devonian shale, Oriskany sandstone, and Helderberg limestone. The principal ore-bearing minerals are goethite and limonite. This report deals principally with the occurrences in Allegheny, Bath, Botetourt, and Craig Counties, Va. The Bureau of Mines, as part of the strategic-minerals program, began a project to develop the reserves of the area in November 1943; and continued until December 1944. Work started near Oriskany and extended northeast for nearly three-fourths of the area of the more important deposits. During the program 163 holes were drilled, totaling 11,651 feet; 256 feet of prospect tunnels were driven; 1,346 samples were collected; beneficiation tests were performed; and bulldozer trails and trenches wore excavated. The work served to delimit and appreciably extend the reserves of several areas. Analyses of channel samples are -given in appendix A, and diamond-drill and churn-drill hole logs and sample analyses are given in appendixes B and C, respectively.

Jan 1, 1950

By E. C. Lane

[The motor gasoline that s being marketed in the United States this summer slightly more volatile then that sold a year ago. This increase in volatility is shown by a general lowering ref the average distillation rang, of about 2°F. During the post 10 years the Bureau of Mines has made semiannual surveys of the gasoline marketed in the United States, the survey just completed being the twentieth in the series. The 12 cities in which samples were collected have beer chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.]

Jan 1, 1929

By A. C. Fieldner, G. W. Jones

Tests were made at the Government Fuel Yard , operated at Washington , D. C. by the Bureau of Mines , Department of the Interior , in order to determine and improve the adjustment of the carburetors on the trucks used for transporting coal from the Fuel Yard to the different Government buildings in Washington . The tests were made possible through the hearty cooperation of G , S. Pope , engineer in charge of the Fuel Yard . Joseph Burrows and A. E. Foote of the garage department assisted during all the tests and supplied information on the mileage obtained by the trucks for the months preceding and succeding the time the tests were made . The Mack trucks used range in capacity from 2-1/2 to 7-1/2 ttoonnss .. The majority of the carburetors were Stromberg G- 3 type , as shown in Table 2. During the winter months , when the demand for coal is heavy , from 30 to 35 trucks are used . At the time the tests were made , only about ten of the trucks were in daily use , owing to the small demand for coal during the summer months , and scarcity due to labor conditions . Samples of the exhaust gas were taken on the trucks kept in service for summer hauling in order to determine the carburetor adjustment as used . Changes were then made to a more economical adjustment wherever possible , without sacrificing flexibility of operation and power . In every case the adjustments were maintained for maximum power , but were adjusted to the leanest position to give that power . In all but one case the carburetors were found to be adjusted too rich for maximum power and economy . These results are considered in detail in a later part of this report .

Jun 1, 1923

By R. Hogg, T. F. Dumm

"Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been compared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes.Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in· some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples INTRODUCTIONA primary goal of mine ventilation is the control of airborne dust, especially in the ""respirable"" size range, typically defined as finer than about 5 to 10 µm. It follows that determination of the amount and characteristics of the respirable dust is an important factor in evaluating the performance of ventilation systems. Particle size information on airborne dust in mines is commonly obtained by in- situ measurements using cascade impactors. However, these tend to be inconvenient for routine data collection and the alternative approach of collecting samples in the mine, on filters for example, and returning them to the laboratory for detailed analysis is very attractive. Questions have often been raised, on the other hand, as to the appropriateness of this approach. How well · do such laboratory methods describe the distribution of aerodynamic diameter of the airborne dust particles in the mine environment? The purpose of the work described in this paper was to evaluate some laboratory sizing methods and to compare the results of such measurements with the size data obtained by the direct, in-situ method."

Jan 1, 1989

By T. M. Romslo

The Lake Shore property, located in the early 1880's, contains copper-bearing deposits that have been developed by surface excavations, underground workings, and churn-drill holes. Operation of the property ended in 1929 with a total recorded production of 280,000 pounds of copper. The property is near the foot of the Slate Mountains, which are made up mainly of probably the Pinal formation of pre-Cambrian age. In the mine area there are a few outcrops of granite, which is exposed over a large area east of the property. Other outcropping rocks on the property are limestone, quartzite, and diabase. The limestone and quartzite probably are the Mescal and Troy formations of pre-Cambrian and Cambrian age, respectively. The predominant copper mineral is chrysocolla, a hydrous silicate that occurs mainly as fracture filling in bedded schist. It is also, the principal copper mineral in the shear zone at the schist-granite contact and in limestone southeast of the main workings. Investigation of the Lake Shore property by the Bureau of Mines included both topographic and geologic mapping, exploratory drilling, and metallurgical test work. One diamond-drill, hole and five churn-drill holes were completed for a total of 2,872.5 feet. Drilling started January 19 and was completed May 13, 1949.

Jan 1, 1950

By R. W. Geehan

The Yellow Pine zinc-lead mine, situated about 3-1/2 miles northwest of Goodsprings, Clark County, Nev., was explored by core drilling during the fall of 1942 and the summer and fall of 1944 by the Bureau of Mines in cooperation with the Federal Geological Survey. The Yellow Pine district was located in 1855. The original claims covering the Yellow Pine mine were located in the following years: Rover, 1892; Hilo, 1897; Bybee, 1900; Radio and Como, 1906. The mine was operated by the Yellow Pine Mining Co. from 1906 to 1929. This company was dissolved in 1935. At a later date, S. E. Yount and the Security First National Bank of Los Angeles, Calif., acquired ownership of the mine. Since 1939, the mine has been operated in a small way by leasers. Production has been at least 175,000 tons averaging about 10 percent lead and 25 percent zinc, with a gross yield of $5,785,174. Virtually all ore produced by this mine consisted chiefly of oxidized zinc and lead minerals and came from long, pipelike shoots in the 100-foot thick Yellow Pine limestone. Ore shoots are sharply defined; elsewhere, the limestone is nearly barren. Numerous faults cut the mine into blocks. Ore is now mined in an open stope, but in the past, large tonnages wore mined in stopes by square-set methods. Ore produced recently was shipped direct to smelters unprocessed; in the past, it was milled by gravity and produced separate lead and zinc concentrates.

Jan 1, 1949

In this U.S. Bureau of Mines report, proposed narrow-vein and longwall mining concepts using drill-split technology (described in part 1 of this series) and in situ liner concepts (described in part 2 of the series) are combined and applied conceptually to environmental problems. Proposed applications deal with (1) acid mine drainage (AMD), (2) solid waste disposal, (3) site remediation, and (4) pollution prevention through innovative industrial design. For control of AMD from abandoned hillside mine workings, it is proposed that source veins be re-mined, processed for residual values, then backfilled using an impermeable compound backfill mix. For solid waste disposal, "vertical landfills" are proposed, consisting of trash-backfilled underground rock quarries. Vertical landfill activities take place in in situ lined containments that geohydrologically isolate the mining-backfilling activities. Site remediation through the creation of in situ underliners, for the capture of toxic leachates, and pollution prevention through the underground storage of toxic, flammable, and explosive materials in in situ containments, are proposed.

Jan 1, 1995

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989