Search Documents

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at, the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-clement method for the evaluation of shaft pillar mining plans and shaft stability. This report, one of three in a series describing the Ross shaft pillar case study, focuses on the premining stability analysis. The two-dimensional computer program UTAH2 was used in advance of pillar mining; results suggested that the shaft would remain stable. Subsequent reports describe parts 2 and 3 of the study. In part 2, borehole extensometers and other instruments were installed to provide data for model verification and shaft monitoring. Results of the recalibrated two-dimensional model confirmed the premining stability evaluation. However, after mining began, great concern developed because of the appearance of cracks and other signs of ground movement over considerable distances from the area of active pillar miping. In part 3, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By Martin J. Gavin

The oil- shale studies of the Bureau of Mines , conducted in cooperation with the State of Colorado and the University of Utah , have for their primary purpose the determination of retorting and refining conditions most favorable for obtaining the highest yields of most satisfactory products . Oil shales , typical of the deposits in several States , are retorted in carefully controlled retorts of differe types , the conditions being varied in successive runs as the results indicate that improvement in the yield and quality of the products most desired may be expected . Each shale presents a somewhat different problem , for it has been found that different shales treated under similar conditions yield products of different natures , and also that the same shale will yield products of different natures when retorted under different conditions . Some shales apparently can not be made to yield , under any set of conditions , products of so high an order as are yielded by other shales . This indicates that the oil -yielding materials of certain shales differ in constitution and in their manner of breaking down when undergoing destructive distillation . Other shales appear to contain oil - yielding materials that resemble each other closely as regards chemical constitution , yet they require some. what different conditions of treatment , if products of similar nature are to be produced from each . In such cases the controlling factors seem to be the richness of the shale that is , its content of oil -yielding material and the physical and chemical nature of its mineral parts .

Mar 1, 1922

By Stephen Utter

Stresses induced by block-caving mining were estimated from in-place measurements of strain or deformation in rock and concrete around mine openings. The four types of gages used for measurements in the Climax Molybdenum mine during 1959-61 were Whittemore gage, Carlson strain meter,2 Valore strain cell, and Climax extensometer. Gage performance in the laboratory was evaluated by stressing instrumented rock and concrete specimens in a universal testing machine and by comparing measurements taken by the gages and a standard gage. Gage performance in the mine was evaluated by comparing measurements taken during an 18-month test. The Whittemore gage, Carlson strain meter, and the Climax extensometer proved suitable for the investigation; the Valore strain cell, effective in the laboratory tests, gave erratic measurements in the mine.

Jan 1, 1965

By C. C. Popoff

The Dunkleberg district is in the Flint Creek Range of the northern Rocky Mountains, about 45 miles northwest of Butte, Mont. Silver - lead and zinc mineralization occurs over an area 4 miles long from north to south and 1 to 2 miles wide from west to east. Ore in appreciable quantity has been produced, mostly from the Forest Rose group of mines in the southern part of the district. The Forest Rose mine was the largest producer of lead and the Wasa mine, a mile farther south, the main producer of zinc. The total output of ore from these properties during World War II was 113,000 tons, or 98.2 percent of the total recorded production of the district. The Wasa mine was examined by a Bureau of Mines engineer2/ in 1944. Subsequent investigations during 1946, 1947, and 1948 included trenching and drilling Fn the Wasa area and examination of the Forest Rose and other mines.

Jan 1, 1953

By R. G. Sandberg

The Bureau of Mines investigated a hydrometallurgical procedure to recover gold, silver, and byproduct lead from a complex lead-zinc sulfide ore. A ferric chloride (FeCI3) preleach, at 40° C in 6 h, extracted about 50 pct of the zinc and formed insoluble silver and lead chlorides. Subsequent acid thiourea leaching, for 1 to 3 h at 40° C, extracted about 85 pct of the gold and silver. Lead chloride was solubilized from the remaining residue with NaCI brine solution at 55° C in 1 h. Lead metal was recovered from the brine solution in an electrolytic cell with an anion perms elective membrane at a current efficiency of 95 pct and current density of 100 A/m2. Spent FeCl3 leach solution was reoxidized in the anode compartment at a current efficiency between 75 and 95 pct.

Jan 1, 1986

By J. J. Sammarco

Light emitting diodes (LEDs) are emerging as viable replacements for incandescent-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. The present paper describes the performance of LED and incandescent sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and airflow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Secondly, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and incandescent sources can be magnified toward the end of a 10­hour battery discharge cycle. Empirically, we have determined that after 8 hours at an ambient temperature of 25 °C, the average light output of an incandescent cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and airflow on the light output of an LED and incandescent cap lamp were conducted in the NIOSH Safety Research Coal Mine (SRCM). The LED cap lamp yielded a vertical average illuminance improvement of approximately 9.5% and the INC cap lamp yielded a vertical average illuminance degradation o f approximately 4%. The differences between LED and incandescent cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38 % more efficient than the incandescent cap lamp with a lead-acid battery at the end of the 10-hour driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the incandescent light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, especially given that the light output will decrease an additional 30% to 45% over the period of a 10-hour shift. The implications of the differences between LED and incandescent sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and incandescent cap lamp visual performance research.

Jan 1, 2008

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Butler County, Pa. It is one of a series planned to determine which coals are suitable for producing metallurgical coke, either as mined or after beneficiation. More than 2 million tons of coal was produced in Butler County in 1958, of which about 25 percent was cleaned mechanically in four cleaning plants. Updating the 1942 coal-reserve estimates made by Ashley to December 31, 1958, more than 1,266 million tons of recoverable coal reserves remain in the county in beds that arc 24 inches or more thick. The Upper and Lower Freeport, Upper, Middle, and Lower Kittanning, Clarion, and Brookville beds were selected on the basis of production and estimated minable reserves. Sample locations were chosen after a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Four samples each were collected from the Upper Freeport and Middle Kittanning beds, three samples from the Brookville bed, two, samples from the Upper Kittanning bed, and one sample each from the Lower Freeport, Lower Kittanning, and Clarion beds.

Jan 1, 1960

By Frederick K. Allgaier

This is the first in a series of progress reports on the longwall subsidence research program at the Bureau of Mines Denver Research Center. As part of this program, the Bureau and the Utah Power and Light Co. are cooperating on a study conducted at the Deer Creek Mine, which is directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. A monitoring network has been established at the Deer Creek Mine to measure subsidence over four adjacent longwall panels. To date, two panels have been mined. Subsidence began as the first panel was mined and continued for 1 year following completion of the panel, during which time the adjacent panel was mined" A maximum of 2.7 feet of subsidence occurred over the two longwall panels mined at a depth of 1,500 feet. Because of the length of time that subsidence continued after mining, the final subsidence profiles and angle of draw have not yet been determined.

Jan 1, 1982

By R. V. Lundquist

Aeration in water slurries and controlled drying of manganous hydroxide produced from dithionate leaching of Artillery Peak manganese ores from Arizona were investigated by the Bureau of Mines at its Electrometallurgical Experiment Station, Boulder City, Nev., to determine whether a simple process could be developed for converting this product into a battery-grade manganese dioxide. The properties of manganese dioxide prepared by the thermal decomposition of manganous nitrate were investigated also. Manganese dioxide suitable for use in batteries was not obtained from the dithionate leach product, but some of the factors controlling its oxidation were isolated. Aging of manganous hydroxide was of major importance in retarding its oxidation by aeration. Sodium hydroxide and sodium silicate promoted oxidation by drying. Optimum quantities were about 0.85 mol of sodium hydroxide and 0.2 mol of sodium silicate per mol of manganese, and drying temperatures of 200° C. produced yields of manganese dioxide up to 90 percent of the manganese present. Higher temperatures and concentrations of reagents carried oxidation of manganese beyond its tetravalent state.

Jan 1, 1957

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. The 15 countries that constitute the region accounted for 28% of world crude petroleum output, 17.2% of world natural gas plant liquid production, and 5.3% of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. About 66% of total world crude petroleum reserves and 31 % of total world natural gas reserves are in the Middle East. Transportation and port facilities in the region are geared to expediting efficient and rapid shipment of these materials. Export sales of these fuels provide funding for further diversification of the mineral industry. Additional development of downstream facilities for producing energy-intensive metals such as aluminum and byproducts of the fuels such as petrochemicals and fertilizers can be expected. Earnings from the industry are also channeled by several Governments in the region to mineral industry projects in Africa and elsewhere. Several countries in the region own major petroleum refineries and distribution facilities worldwide. Petroleum prices rose overall during the year owing to the invasion by Iraq of Kuwait in August 1990. Output from both countries, the fourth and fifth largest producers, respectively, in the Middle East, was negatively affected by the war. Kuwaiti crude oil wells and pipeline facilities suffered extensive war damage while exports of petroleum and petroleum refinery products by Iraq ceased owing to a U.N. embargo. The embargo also impacted Jordan, an exporter of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was more than made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion of the increase.

Jan 1, 1992

By Fremont F. Clarke

"INTRODUCTION Clay beds of southwestern North Dakota were investigated to determine (1) the average alumina content of the clays in four principal areas of occurrence, (2.) which, if any, would be the most feasible method of extracting alumina from the clays, and (3) whether the clays had any other commercial uses.During the investigation exposed sedimentary beds were examined for clay and the thickness and areal extent of outcropping clay beds in the more promising areas were measured. Four-principal areas of bentonitic clays, comprising 6,967 acres in Stark, Slope; and Billings Counties, N. Dak., were mapped and sampled.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our natural resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chiefs analyzes samples and makes beneficiation tests.Acknowledgment is duo John P. Gries, professor of geology, South Dakota School of Mines and Technology, for his studies of and advice on geological phases of the work. His data were drawn on freely in preparing this report; also E. D. Gardner, regional engineer, Rolla, Mo., and E. Y. Dougherty, district engineer, Rapid City, S. Dak., for assistance and advice in supervising the program."

Mar 1, 1948

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By S. M. Runke

The pegmatite investigations at the Rapid City, S. Dak., Experiment Station during; the pact 3 years have been primarily a study of recovering beryl from nonlithium-bearing pegmatite rock by continuous-testing methods. Beryl concentrates containing 25 to 88 percent beryl were produced from rock that ranged in beryl content from 0.1 to 2.5 percent. The beryl recovery ranged upward from 70 percent but averaged better than 80 percent. Although promising results have been obtained with flotation methods for upgrading these concentrates to standard specifications, additional work is needed to improve and simplify the procedure. In addition, it was demonstrated that several potentially useful coproducts could also be recovered from pegmatite rock. The principal coproducts were mica, feldspar, and quartz. A heavy-mineral product also was made from pegmatites containing tin, tantalum, and columbium. The recovery if these minerals in products meeting the specifications of the commercial users has been reserved for future study. The investigations also included studies on extraction of beryllium from both high-grade beryl and flotation concentrates of medium beryllium content. The procedure investigated consisted of sintering beryl or beryl flotation concentrates with limestone, acid curing the resulting sinter with sulfuric acid to dissolve the beryllium, and water leaching to extract the beryllium. Over 90 percent of the beryllium was extracted by this procedure. Most of the optimum conditions and quantities of reagents were determined for dissolving the beryllium. As aluminum and iron also were taken into solution by the acid, further research is needed on methods of recovering high-grade beryllium salts from the solutions containing these elements.

Jan 1, 1957

By Robert E. Dye

This paper describing the mining methods employed and setting forth prevailing, costs at the property, is one of a series being prepared by the United States Bureau of Mines dealing with properties in various mining districts of the United States and Canada. The Vipond mine is a gold property located at Timmins, Ontario, Canada, and operated by the Vipond Consolidated Mines (Ltd.). For the past fiscal year (ended July 31. 1930) ore was mined and milled at the rate of 310 tons per day, and the value of the bullion produced was $896,397.61.

Jan 1, 1931

By R. R. Sayers

The terms "sanitation and }\Vgienen are often used interchangeably, but it is more "' usual to apply ttsani tat ion'' to th environment or surroundings, and nr.ygieneto the iiiividual, The subject,. h9wever, is so broad that only a few of the phases of sanitation will be di.acusae in ·this paper, vmile the various Fsea of hyg:tene will be deferred for later consideration. One of the bes.t .iaf ini tions of sanitation that I have hearci was given by ur. L. L • Lumsden, of the U, S. Public Heal th Service, who state.d that "'sanitation is t-he c.oir .. 'Don-sens$ application of the principles of cleanliness,

Aug 1, 1922

By S. M. Shelton, M. M. Fine, T. L. Johnston

"INTRODUCTION The Bynum property is about 15 miles west of Gadsden and 1 mile north of Walnut Grove, Etowah County, Ala. The ore lies in layers and as irregular masses and pockets in the clay residue from decomposed quartzite and limestone formations to the district.The property has been developed by means of numerous shallow shafts sunk to water level - about 25 foot. Operations are confined to small-scale, selective mining of pockets of high-grade ore. The ore is marketed directly, without beneficiation. The property does not yield a large amount of manganese ores. No estimates of reserve ore tonnages are available.A 206-pound sample was furnished for test. It was taken at random from a stock rile estimated to contain 130 tons of ore. The sample con¬sisted of a mixture of manganese oxides, iron oxides, and siliceous fragments in clay. The manganese occurred largely as soft, unconsolidated pyrolusite and wad. Some hard, crystalline pieces of psilomelane were distributed through the soft material. Small amounts of iron oxides were associated with the manganese oxides. Chert, quartzite, and clay comprised the gangue minerals.Dry analysis of the sample was as follows: 36.0 percent manganese, 6.1 percent iron, 2: .0 percent silica, 1.5 percent calcium carbonate, 0.36 percent phosphorus, 3.0 percent alumina, 2.2 percent barium, and 0.31 percent zinc."

May 1, 1942

By L. E. Schultze

Experiments were conducted by the U.S. Bureau of Mines to verify enhancements due to chloride and surfactant additions in the leaching system of chalcopyrite with ferric sulfate and sulfuric acid. A statistical experimental design was used and equipment was designed to eliminate contributions from changes in solution electrochemical potential during the course of the measurements. Results confirmed that chloride additions increased chalcopyrite leaching by as much as 94 pct over the electrochemical potential versus hydrogen electrode range of 630 to 750 mV at pH 1.7 and 50°C. Total iron concentration had no effect over the range of 1 to 5 g/L. The effect of surfactant addition was less well defined. While additions of LA 790 (a polyoxyethylene lauryl ether) resulted in increased copper leaching in several of the tests, the differences were too small to be statistically significant. No interaction effect could be verified.

Jan 1, 2010

By A. T. Iannacchione

Roof-rock instability in advancing sections of underground coal mines is a major contributing factor to accidents resulting in fatalities and injuries. Such roof-rock conditions can also result in loss of production due to additional cleanup time and increased amounts of reject material. The Bureau of Mines is investigating fundamental geologic factors affecting coal mine roof-rock instability in order to develop techniques to predict zones of potential unstable roof-rock. Two distinct directional trends of unstable shale roof-rock in a mine working the Upper Kittanning Coalbed are delineated: one trend is associated with the sandstone-shale transition zone, the other with a fault system. The unstable shale roof-rock associated with the transition zone, a consequence of differential compaction, is comprised of slickensided roof-rock. Whereas, the unstable shale roof-rock associated with the fault system, a consequence of structural deformation of the strata, is comprised of fault planes. These faults, small in comparison to the sandstone-shale transition zone, are difficult to delineate with a standard drilling program. Trends of the transition zone associated with the sedimentary facies change are projected into unmined portions of the coalbed with the aid of exploration core data.

Jan 1, 1981

By Pete G. Kovalchik, Lynn A. Alcorn, Rudy J. Matetic, Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage is comprised of seven different types of machines. The continuous mining machine is first among all the equipment with 35% of the noise overexposures. The ational Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce excessive exposure for operators of continuous mining machines and preventing additional cases of oise Induced Hearing Loss (NIHL) by developing low-cost retrofit noise controls for mining equipment. This paper describes a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 26.4% and 27.4% noise exposure reduction for the continuous mining machine operator. This research is providing the mining community with an additional noise control to be utilized on continuous mining machines, therefore reducing operator noise overexposure. Utilizing this newly developed noise control, along with previously proven controls for the continuous mining machine chain conveyor, will provide operators of these machines an opportunity to be within the MS HA-Permissible Exposure Limit (MSHA-PEL).

By John R. Troxell

"INTRODUCTION The Ahles iron mine, also known as the Pequest mine, in Warren County, N. J., was operated continuously for 15 years and was still in ore when it closed in 1916.Tie property was examined by an engineer of the Bureau of Mines in March 1943. 3/ This examination led to an investigation of the deposits by the Bureau by diamond drilling two holes under the old workings to determine whether the extends downward.This report describes the work done at the Ahles mine by the Bureau and presents the data obtained.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report.The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation was under the general supervision of J. B. Zadra, acting regional engineer, and under the immediate supervision of G. D. Jermain, district engineer for the States of Pennsylvania, New Jersey, Maryland, and Delaware. The author was in direct charge of the project.The chemical analyses for the project were performed at the College, Park, Md., laboratories of the Bureau of Mines under the direction of M. S. Sheftel. The ore-dressing tests were conducted at College Park under the direction of Frank Lamb. Preston E. Hotz, of the Federal Geological Survey, logged and interpreted the drill cores."

Apr 1, 1948