Search Documents

By W. P. Yant, G. W. Jones

"Introduction.During the past two years the Bureau of Mines has conducted a study of natural-gas heaters*** to determine (1) what types of heaters literate carbon monoxide; (2) why carton monocide is liberated; and (3) how, by change of design or construction, the liberation of this gas can be largely eliminated, In addition to the above study the bureau has investigated cases in the Pittsburgh dis¬trict where fatalities have resulted from carbon monoxide given off by natural-gas heaters.Since these fatalities were first brought to the attention of this bureau through the press, it is likely that some cases were missed and thus not listed. On the other hand, some cases reported as being due to carbon monoxide poisoning, on investigation were found to be due to causes other than carbon monoride.The cases listed herein were shown in all probability to be due to carbon monoxide. Those in which there is any doubt have been omitted; so have those in which there was part asphyxiation, where the victims later recovered."

Feb 1, 1924

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976

By Sidney Katell

This report, covering the period January 1968 through December 1968, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the tenth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost of engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Lines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress s 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing. 9. Cost Engineering. 10. European Chemical News. 3 11. Hydrocarbon Processing. 12. Industrial and Engineering Chemistry 13. Oil and Gas Journal. 14. Petroleum Engineer. 15. World Oil.

Jan 1, 1969

By D. Harrington

For many years the Federal Bureau of Mines-in cooperation with other agencies-has been making investigations and compiling and publishing reports and statistics on accidents in the various branches of the mineral industry.4 Its assistance has been enlisted also in health, safety, and ventilation problems' incident to the driving of many large tunnels in the United States in recent years. As part of this work the Bureau has compiled considerable statistical and other information on accident experience in the tunneling branch of the heavy-construction industry. It has always been difficult to obtain up-to-date information on tunneling methods and tunnel accidents. Published accounts of tun¬nel construction furnish much interesting material of engineering, historical, or fiscal value, but usually little or no attempt is made to discuss and critically analyze the means taken to preserve the health and life of employees.

Jan 1, 1941

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By J. R. Thoenen

Up to 1914 almost all of the world's supply of potash came from Germany and Alsace. With the cessation of shipments from Germany during the World War the importance of a domestic supply was evident, During the past 15 years the United States has been working toward the establishment of a domestic potash industry which would end foreign dominance in this commodity. The Federal government has taken an active part in this program. As its share in the work, the Bureau of Mines has ascertained the potash resources in certain districts through core drilling and has engaged in a comprehensive program of research on the extraction of potash from its various minerals. Until the passage of the Winter bill (H. R. 496) by Congress in 1928 the Bureau of Mines had not been able to give any consideration to the western ores, wyomingite (leucite) and alunite. With the Passage of this bill, however, the ray was opened for the extension of the potash studies to cover these materials.

Jan 1, 1932

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

"M bed, Matanuska valley, Alaska, coal carbonizingproperties B 510M spectral lines, low-energy, study RI 5538Mab shaft, Leadvile district, Colo., investigation RI .1518Maberry process, for aluminum chloride TP 321"

Jan 1, 1960

By V. L. SKITSKY

Geophysical Abstracts are published by the Division of Geophysical Explo- ration of the U. S. Bureau of Mines as an aid to those engaged in geophysical research and exploration. Inasmuch as geophysicists in the field may have little opportunity to consult libraries, the policy of the Division is to provide abstracts suffi- ciently informative in themselves to keep readers abreast of literature and patents published in the United States and abroad. - DISTRIBUTION. Abstracts 1-86 were issued as Information Circulars by the Burca of Mines; Abstracts 87-111 appeared as Bulletins of the Geological Survey; Abstracts 112-127 have been published as Information Circulars by the Bureau of Mines; succeeding issues will be resumed by the Geological Survey.

Jun 1, 1947

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

The 1969 Lignite Symposium was held at Grand Forks, N. Dak., on May 1-2, 1969. Cosponsored by the University of North Dakota and the Department of the Interior, Bureau of Mines, the meeting was the fifth in this series. Registrants from many States and Canadian Provinces attended the meeting representing many segments of energy-oriented companies, State and Federal Government, and universities. At 2-year intervals, these symposia provide a common meeting place where recent research and developments in technology and utilization of energy resources with emphasis on solid fuels (lignite) are presented. Proceedings3 of the previous symposia including a Forum held in 1958 have been published.4

Jan 1, 1970

By G. L. Bartlett

"INTRODUCTION The major objective of our research is to help reduce the incidence and severity of coal worker's pneumoconiosis (CWP). To that end, this project is designed to improve our understanding of the processes that lead to pulmonary dysfunction following mine dust exposure, and how those processes might be interrupted or attenuated. The response of the lung ' to inhaled particles is complex, and the course of development of disabling CWP is slow and unpredictable. From among the numerous cellular and molecular interactions involved in the pulmonary response to inhaled particles, this project is focussed on the role that the pulmonary alveolar macrophage (PAM) may play in regulating the activity of fibroblasts.The PAM is the lung cell that has the most immediate and the most obvious interaction with inhaled particles. Within a short period after particles are arrested in the alveolus of the lung, they are phagocytized (engulfed) by these specialized cells. The PAM then has a diverse potential repertoire of subsequent activities. Which reaction actually ensues is determined, in large part, by the nature of the phagocytized _particles. Activated PAMs produce a variety of products that may affect adjacent lung tissue, including superoxide free radical, elastase, collagenase, prostaglandins, platelet activating factor, etc. Those may well be important in the pathogenesis of CWP, but they are beyond the scope of this project. Background information that is cogent to this project has come primarily from investigations using animal models of silicosis and asbestosis. PAMs that have ingested silica particles synthesize and release molecules that control the behavior of surrounding cells. One such mediator is interleukin-1 (IL-1), a molecule that plays a central role in many aspects of the response to injury. It can stimulate fibroblasts (the cells that help to hold tissues together) to release the enzyme collagenase, resulting in breakdown of the structural collagen fibers that support the lung tissue. IL-1 also stimulates fibroblasts to undergo mitosis and to proliferate, which is an initial stage of fibrosis. Certain stimulants cause PAMs to release fibroblast growth factors (FGFs) that are distinct- from IL-1. Under other circumstances activated PAMs synthesize and release molecules that stimulate fibroblasts to accelerate synthesis of collagen fibers, thus contributing to fibrosis. Although these observations provide a valuable precedent for analysis of the mechanisms involved in CWP, their relevance to CWP cannot be assumed since most of those studies involved macrophages or fibroblasts obtained from tissues other than the lung, and because almost none of them have used CMD as the stimulating particles. Therefore, the goal of this project is to learn how exposure to CMD affects the behavior of PAMs, and in turn how products of dust-exposed PAMs affect fibroblasts and the process of fibrosis in the lung."

Jan 1, 1988

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

By Scott W. Hazen

COMPREHENSIVE summary is presented of results of several years of research at the Bureau of Mines Mining Research Center at Denver on adapting and applying techniques of statistical analysis in mine and mineral-deposit sampling and in computing grade and tonnage of ore for a mineral deposit. In addition to elementary statistical theory the material presented in the bulletin includes: (1) Certain special statistical techniques that have been found useful in mining applications; (2) problems, implications, and limitations that may be encountered in applying these techniques in mine sampling and evaluation; and (3) numerous examples to demonstrate application of the theory and techniques.

Jan 1, 1967

By H. H. Heady

This Bureau of Mines report provides specific information regarding the analysis of ores, concentrates, and bullion. It describes analytical services provided by some Federal agencies, and discusses analytical techniques applicable to the precious metals. The appendixes list Bureau of Mines State Liaison Offices and commercial assay laboratories.

Jan 1, 1976

By G. St. J. Perrott, G. W. Jones

"In the course of its investigations pertaining to the promotion of safety the Bureau of Mines is actively engaged in investigating all promising materials that may be of value in rendering methane or other combustible gases, vapors, or solids less inflammable.Added substances are of value if such additions narrow the limits of inflammability, raise the ignition temperature, lower the speed of propagation of flame, or reduce the maximum pressure developed. Of major importance is the effect of added materials on the limits of inflammability, because methane is the chief combustible s liberated in mines, considerable work has been done with extinguishing agents on methane flames. For obvious reasons, a substance to be of value for the extinction flames should be a gas, or a liquid having a sufficient vapor pressure to give concentrations of the vapor in sufficient amounts to extinguish the flames or markedly narrow the limits of inflammability. The substance should be nontoxic, cheap, and noncorrosive and must be incombustible. Solids, such as rock dust, are undesirable and of little value for combustible gases because they soon settle out of the atmosphere, and their flame- extinguishing value is thereby lost. There are at present only a few gases and vapors-for example, nitrogen, carbon dioxide, and carbon tetrachloride-which meet these requirements.The extinction of methane flames by nitrogen, carbon dioxide, and argon has been reported by Coward and Hartwell 4; the extinction by water vapor by Coward and Gleadell 5, and the extinction by helium and carbon tetrachloride by Coward and Jones 6."

Oct 1, 1930

By Sean Gallagher

This report was written in an effort to provide better control measures for low back pain (LBP) and low back disability in the mining industry. There are numerous factors associated with development of LBP, many of which can be effectively controlled while some cannot. Better job design is promoted as the best method of reducing cases of LBP and can also reduce the disability (i.e., lost time from work) associated with LBP when it happens. The report draws attention to what is currently known about LBP, what the causes are thought to be, and discusses recent back injury trends in the mining industry. Research describing unique physical demands in mining, such as the capabilities and limitations of working in awkward postures, is also presented. Methods that can be used to prevent initial LBP episodes are provided, including facilities design and layout for materials and supplies, use of mechanical-assist devices, improved design of lifting tasks, and better seat design. Methods of reducing the disability associated with LBP (including workplace design, proactive return-to-work efforts, communication, and management commitment) are also discussed. The report concludes that control of LBP and disability in mining requires a comprehensive approach to limit the repetitive loading that can occur on the low back due to manual materials-handling tasks and exposure to whole-body vibration (WBV). Specific recommendations include the following: ? Successful LBP prevention efforts require a proactive program that has strong management commitment and incorporates employee involvement. ? More efficient supply handling systems and use of mechanical-assist devices can greatly reduce exposure to hazardous lifting tasks. ? Lifting tasks should be designed to minimize low back stress. Tools to evaluate and redesign lifting tasks are presented. ? Improved seat design can reduce exposure to WBV and improve posture, leading to reduced LBP risk. ? The disability associated with LBP can be reduced. Getting the worker back on the job as quickly as possible is in the interest of everyone involved.

Sep 1, 2008

By David A. Monaghan

On January 14, 1974 a fire occurred in the 3 East mains of the Joanne Mine of Eastern Associated Coal Corp. in Rachel, West Virginia. The mine was evacuated without injury and sealed completely at the surface within 24 hours. It was decided by the coal company along with the U, S, Bureau of Mines, the West Virginia Bureau of Mints and MESA that remote sealing of the fire zone would be attempted. This report summarizes the remote sealing effort and those activities directly related to the remote sealing effort. This chapter provides a brief history of previous remote sealing attempts, a description of the recently developed remote sealing system and a description of the Joanne Mine operation as it related to and affected the remote sealing effort.

Jan 1, 1975