Search Documents

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

By A. N. Baldwin

This report documents the work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plans developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By A. J. Kauffman

This study compiles data on the zircon resources of the Pacific Northwest States, Alaska, and California, to determine the productive capability of industrial concerns to make ductile zirconium and hafnium, and to investigate markets for the nonmetallic products of zircon. West coast zircon resources are large but mostly marginal to submarginal. Development of a stable and profitable zircon mining industry on the west coast will depend upon recovery and utilization of the other associated heavy minerals needed by regional and national markets. The west coast has the only completely integrated facility for processing zircon sand to reactor-grade zirconium and hafnium and for making fabricated products from these metals. The future of the zirconium metal industry appears to be good because of increased use of the metal for nuclear propulsion and power-generating plants.

Jan 1, 1965

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By W. E. Wallace, S. -G. Xing, M. J. Keane, J. C. Harrison

"SummaryDiesel-exhaust particles from two sources were dispersed in aqueous mixtures of dipalmitoyl phosphatidyl choline, a major component of pulmonary surfactant, and were tested for genotoxicity. Diesel samples from the same sources were extracted with dichloromethane and transferred into dimethyl sulfoxide and subjected to the same assays. Both types of extractions yielded similar results in both the Salmonella mutagenicity assay and the sister-chromatid exchange assay using V79 cells. After separation of the samples into supernatant and sediment fractions, the activity of both diesel samples was shown to reside exclusively in the supernatant fraction for the solvent-extracted samples, and exclusively in the sedimented fraction for surfactant dispersed samples. These findings indicate that genotoxic activity associated with diesel particles inhaled into the lung may be made bioavailable by virtue of the solubilization / dispersion properties of pulmonary surfactant components.While diesel engine emissions are associated primarily with transportation, they are also very common in the workplace. Estimates for the U.S. are that as many as 1.35 million workers in as many as 80 000 workplaces are exposed to the combustion products of diesel engines (NIOSH, 1988). These occupations include, but are not limited to mining, agriculture, motor vehicle maintenance, fork lift truck driving, truck driving, and tunnel and bridge operation."

Mar 1, 1992

By P. H. Francis

In This report, factors which currently enter into the design, manufacture, and quality assurance of explosion-proof enclosures are reviewed, with special emphasis given to the sealing concepts and sealants/cements, per se, for lenses. The physical and mechanical properties of a number of representative sealants and adhesives are measured, and found to exhibit great variance, with few discernible trends which might afford a firm base on which to establish minimum property standards. Accordingly, acceptance criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure rather than upon the minimum mat real properties of its constituents. Procedures or surface preparation of adherends, and for quality assurance, also are proposed.

Jan 1, 1980

By C. H. Riggs

THIS REPORT give's the results of a study of the central and south parts of the Cushing oilfield, including a description of the geology, a review of the production history, and estimates of oil reserves available by secondary-recovery methods. Each of the major producing zones of the field is treated separately. The report, which is one of a long series of field studies the Bureau of Mines has conducted over the past 40 years, was prepared to aid operators to increase oil recovery and to help prevent underground waste in the Cushing field, in the State of Oklahoma, and in the United States. The geology and production history are presented not as a review of past behavior of the Cushing field but rather to interpret the possibilities for increased oil recovery by future development of this and similar areas. The field, which is in the northwest corner of Creek County, Okla., was discovered in 1912 and developed during 1913 and 1914. For several years it, was one of the most important areas producing high-grade crude oil in Oklahoma. Although some oil has been recovered from each of 10 separate reservoirs, nearly 98 percent of the total recovery of oil in the area studied was from 4 major producing formations (table 1). Of these, only the Bartlesville [ ]

Jan 1, 1958

By Z. T. Bieniawski, Benjamín Celada

After emphasizing the importance of quantitative rock mass classifications in mining, originally directed to selection of rock support measures, but subsequently to estimates of rock mass properties such as rock mass strength and rock mass modulus of deformation, current attention calls for a classification specifically for rock mass excavability by tunnel boring machines (TBMs), which are used extensively in tunneling as well as in the mining industry. This paper introduces the Rock Mass Excavability (RME) index for predicting excavability of rock masses by TBMs using a quantification of machine performance and rock mass conditions. The RME index is based on five input parameters aimed at relating rock mass behavior and machine characteristics: (1) uniaxial compressive strength of the rock material, (2) drillability/abrasivity, (3) rock mass jointing at mine drift face, (4) standup time of the excavation, and (5) groundwater inflow. Development of the RME index entailed the collection of extensive data from more than 28 km of tunnels and some 400 case records from projects in Spain involving double-shield TBMs. In the process, a number of statistical correlations have been established between RME and such output parameters as degree of machine utilization, advance and penetration rates, thrust and torque of the cutterhead, and the specific energy of excavation. It was found that the RME index provides a particularly significant correlation for predicting the average rate of advance (m/day). In essence, the RME index is a classification system that features interaction of rock mass conditions with boring machine characteristics for use in the early stages of a project. It should be noted that the RME index does not replace the Rock Mass Rating (RMR) or Q-systems as used in mining and tunneling; indeed, one of the RME input parameters, standup time, is determined from the RMR. However, the approach presented introduces a specialized tool relevant to excavating tunnels and drifts. Possible applications to hard-rock mining are explored.

Jan 5, 2007

By Terry J. Close

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, U.S. Bureau of Mines personnel studied 7,040 acres of the 7,240-acre Sheep Mountain Wilderness Study Area (OR-006-003) in order to evaluate its identified mineral resources. The area studied is along the divide between the Snake River and Pine Creek about 1.5 mi south of the village of Oxbow in Baker County, OR. No mineral resources or mineral-related activities were identified in the Sheep Mountain study area. The basalt covering most of the study area has no known mineralized sites. However, it contains common agate and opal that is of limited interest to mineral collectors. This basalt (stone) could be used locally as construction material (crushed stone or fill); however, suitable material is wide spread in the region and more accessible to possible markets.

Jan 1, 1987

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1995

By Staff

This U.S. Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles.

Jan 1, 1989

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By J. J. Forbes

Since 1910 the Bureau of Mines has given training in the care and use of oxygen breathing apparatus under conditions that may exist during mine fires and after mine explosions. In 1929 the Bureau supplemented this instruction by initiating a course in advanced mine rescue training to prepare mine officials and others to organize men for mine rescue and recovery operations. The course of instruction has been developed and expanded since its inception to keep abreast with new ideas, methods, and equipment. Four miners' circulars were issued to be used in the training course. The first of this series (Miners' Circular 33) deals with mine gases and the various methods of detecting them; the second (Miners' Circular 34) gives instructions for sampling and analyzing mine atmospheres; the third (this circular) describes methods and equipment for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures in sealing and unsealing mine fires and in conducting recovery operations, These circulars have been revised from time to time to keep them up to date.

Jan 1, 1954

By J. A. Kost

The objectives of this contract were to determine the amount, size, and deposition of float coal dust (74 x 10 microns) generated during the mining and transporting of coal in underground U.S. mining operations. Rock dust distributed by trickle dusters was also sampled. In addition to four belt-transfer points, two continuous and two conventional mining sections were sampled at five mines located in Pennsylvania, West Virginia, Kentucky, and Illinois. Float-dust samples were collected on deposition pans; total airborne dust was collected with MSA Model C personal samplers equipped with Unico filter casettes; Andersen cascade impactors provided relative size distributions of the samples. Production, airflow, and water flow were monitored to examine their effect on dust levels.

Jan 1, 1981

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By M. J. Kirwan

[There have been large increases in the oil production and casing-head gas production of certain wells on the Quinn dome (northern part of the Lyons-Quinn field of Oklahoma) caused by large volumes of gas under high pressure entering Vie productive oil sand, The oil production of sore of the leases in this part of the field temporarily increased over 100 per cent within a few days after gas entered the oil sand among the leases that had the greatest increases in oil production wore those on which no gas wells were drilled but which were located up-elope on the structure in reference to gas wells on adjoining properties. It is conservatively estimated that 1,444,000,000, cubic feet of gas entered the productive oil sand and, up to January 1, 1924, caused an increase of about 950,000 barrels of oil from this sand. The casing-held gas volumes of a number of wells producing between 25,000 and 75,000 cubic feet of gas per day increased to several hundred thousand cubic feet and a few walls increased to nearly two million cubic feet per day after extraneous gas entered the oil sand from which the wells were producing.]

Jan 1, 1924

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in more intensified efforts in inspections of coal refuse sites. Inspections, however, are mainly qualitative and time consuming. In August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photointerpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Bibliographies of literature reviews in the area of past coal refuse embankment failures, monitoring instruments and methods, and photogrammetry are included.

Jan 1, 1977

By Kenneth L. Rubow, Virgil A. Marple, Zhigun Zhang

"A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important parameter for determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three-dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an scanning electron microscope (SEM). The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three-dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 µm size range. The three-dimensional shape, as is determined from SEM analysis, was used in the theoretical computer program and the results compared. It was found that in most cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%. INTRODCJCTIONThe equivalent aerodynamic diameter (EAD) of a particle, defined as the diameter of a unit density sphere with the same falling speed as the particle in question, is an important size measurement of the particle. This is especially true when attempting to predict where particles may deposit in the respirator tract. Therefore, EAD is an important parameter when considering respiratory diseases caused by particles, such as coal workers pneumoconiosis (CWP).Many instruments will measure the EAD size distribution of the aerosol particles, but few analyze the particles individually. Impactors, cyclones and virtual impactors normally collect particles upon substrates or filters which are · then analyzed gravimetrically to determine the mass concentration of the particles in that size classification. The EAD of particles can be measured on an individual basis with centrifuges, inertial spectrometers and the TSI Aerodynamic Particle Sizer (APS). Centrifuges are most ideally applicable for studying individual particles as the particles are deposited, on long removable foils, at locations dependent upon their EAD."

Jan 1, 1990

By D. S. Kingery

The data obtained from this study cover test areas that are gassy to ultragassy and pillared areas of different sizes and degrees of tightness. The methods of controlling ventilation, applying bleeders, and supporting bleeder entries varied in the different test areas. It was not possible to study all conditions likely to be encountered in coal mines. Undoubtedly, there are areas where bleeder entries, even though properly planned and maintained, might prove unsatisfactory. However, on the basis of this study, the following observations were made: 1. Tests showed that each bleeder system studied provided some movement of air through the pillared area; the quantities of air delivered to the pillar line, ranged from 23 to 82 percent, depending mainly on the extent to which bleeder re-turns were used as main returns from the section. 2. Pressure measurements taken across pillared areas showed maximum pressure drops ranging from 0.05 inch of water for a shallow gob to 2.69 inches for a very deep gob. The pressure differentials varied with the size and tightness of the gob but proved adequate to induce airflow across worked-out areas or through fringes of the gob to the bleeder return system.

Jan 1, 1957

By D. B. Dow

The presence of sulphur compounds in petroleum and its products is, generally speaking, undesirable, and the problems involved in removing such compounds are of great importance to the petroleum refiner and to the manufacturer of gasoline. There are several types of these compounds which are dissimilar in physical and chemical characteristics, as evidenced by different objectionable features which they exhibit, and special treatments have been developed to meet conditions existing in various products. This paper deals with the treatment of natural-gas gasoline for the removal of certain sulphur compounds which, if not removed, impart on objectionable odor and in addition badly discolor the product. The presence of this particular type of sulphur compounds is detected by the "doctor" test.* In some instances natural-gas gasoline is purchased on "doctor" test specifications, and the ordinary purchaser, while not buying on "doctor" specifications, is insistent in his demand for a water white product. Gasoline which fails to meet the "doctor" test, if not received by the buyer within a few weeks after time Of manufacture, may be "off color" enough to warrant a deduction from the market price.

Jan 1, 1923