Search Documents

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By Thomas J. Peters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 17,320-acre portion of the 52,143-acre Little High Rock Canyon Wilderness Study Area (CA-020-913/NV-020-008) in order to evaluate its identified mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 42 miles north from Gerlach. Three areas of epithermal alteration, similar to alteration associated with disseminated gold deposits, were found in the study area. One of the areas occurs along a northeast-trending structural lineament. Southwest of the study area two gold prospects undergoing active exploration, as well JS a gold deposit being prepared for production, occur along the same lineament. The Bureau of Mines examination, however, did not find evidence for gold resources in the study area.

Jan 1, 1987

By L. D. Patts, J. D. Noll, S. E. Mischler, G. H. Schnakenberg

In this study, we evaluated the ambient diesel particulate matter (DPM) concentrations (at the intakes and exhausts of the mine) as the entire vehicle fleet of a stone mine switched from using 35% biodiesel to using a water emulsified fuel (PuriNOx). Elemental carbon (EC) was reduced by 45% when a PuriNOx blend containing 10% water replaced 35% biodiesel and by 57% when a PuriNOx blend containing 20% water was used. Other factors such as engine duty cycle and production changes could potentially cause some day-to-day EC fluctuations, and no direct comparison to commonly used dieselfuels (No. 1 or No. 2) was achieved. Therefore, a second study was performed in a controlled “isolatedzone” environment to fametal mine, comparing PuriNOxto No.1 diesel fuel in a load haul dump vehicle. The EC fraction of the DPM was reduced by about 71% when the PuriNOx blend containing 10% water was used and by about 85% when the PuriNOx blend containing 20% water was employed. This study did not determine how the water emulsified fuel would affect the engine or power.

By Mark S. Sanders

The present study was designed to explore the contribution of organizational climate and management practices to the injury experience in underground coal mines. A cross-lagged panel design was used in which miners from 22 mines completed questionnaires assessing 27 organizational climate, structure, and function dimensions on two occasions, The results strongly support the hypothesis that climate and management practice have casual effect on the incidence of disabling injuries.

Jan 1, 1976

Research 83 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary, General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1983

Consumption and intensity of use trends for twelve metals, by industrial end use, were estimated for 1972 through 198Z. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following four of the twelve metal increased from 1972-82 as follows: aluminum, 1.00 percent; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83 percent; titanium, 7.82 percent; and tungsten, 6.09 percent. Consumption. for the remaining eight metals decreased at average annual rates ranging from 0.58 percent (copper) to 5.37 percent (manganese).

Jan 1, 1986

By James E. Cairelli

The NASA Lewis Research Center, under U.S. Bureau of Mines program direction, performed an assessment of alternative mobile power sources for mining applications. A wide variety of heat engines and energy systems was initially examined to ascertain which could be considered as potential alternatives to presently used power systems. The present mobile power systems are electrical trailing cable, electrical battery, and diesel - with diesel being largely limited in the United States to noncoal mines. Each candidate power source was evaluated in terms, of the following requirements: (1) Ability to achieve the duty cycle (2) Ability to meet Government regulations (MSHA certification) (3) Availability (production readiness) (4) Market availability (5) Packaging capability An initial screening reduced the list of candidates to the following: (1) Diesel (2) Stirling (3) Gas turbine (4) Rankine (steam) (5) Advanced electric (batteries) (6) Mechanical energy storage (flywheel) (7) Use of hydrogen evolved from metal hydrides This list of candidates was divided into two classes of alternative power sources for mining applications - heat engines and energy storage systems. A summary of each class follows.

Jan 1, 1981

By Douglas W. Fuerstenau

A detailed experimental study of breakage kinetics in a batch rod mill indicates that while the system is inherently nonlinear, the feed disappearance kinetics for the finer sizes and the coarser sizes at high holdups is well represented by first-order behavior. The set of breakage distribution functions was found to be normalizable and independent of particle holdup in the mill. The size discretized initial breakage rate functions were found to be inversely proportional to particle holdup and almost directly proportional to particle size. A linearized grinding model that results from the first-order Taylor's series expansion of the breakage rate expression was found to give good simulations of the mill product size distributions without recourse to any parameter improvement routines. Material transport through rod mills was evaluated by investigating the effect of operating variables on the holdup and residence time distribution of particulate solids flowing through the mill. Identical experiments performed in a continuous ball mill helped delineate the fundamental differences in particulate transport through these two types of mills. Mechanistic interpretations of the observed transport phenomena are presented, and their implications in the context of tumbling mill analysis and design pointed out.

Jan 1, 1980

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By Frank M. Vodoklys

This is the final report on Contract H0220049 covering the period from 27 April 1972 to 30 April 1974. The objective of the contract was to develop and evaluate materials and methods to achieve post explosion identification of explosives reliably and economically through the use of phosphor coded grains incorporated into the explosive during its manufacture. A coding system of two spotting phosphors and seven coding phosphors was successfully developed during the execution of the contract. The ability of the coded grains to survive detonation in many different types of explosives was demonstrated and the complete code was extracted from a single 100 micron post-explosion fragment. A method was established for testing grain strength to correlate with field test results and an optical system was designed for extracting the code from the grains. Also in fulfillment of the contract requirements a laboratory method for manufacturing the coded grains was established and ten one-pound samples, each with a different code, were fabricated. Finally, a method was developed for applying a coating of polyethylene to the grains to prevent sensitization of the tagged explosives and the ten one-pound samples were coated and delivered to the Bureau of Mines.

Jan 1, 1974

By S. P. Kinney, P. H. Royster, T. L. Joseph

An investigation of the production of iron in the blast furnace is obviously not an easy subject for research . Enough is known of the mechanical , thermal and chemical conditions existing inside the furnace to say certainly that they are complicated. Furnace operators have found that the process is sensitive to a number of known and to many unknown operating conditions . In order to form any conclusions of value , it seems necessary to collect a large amount of data taken with considerable care and accuracy. These facts make a blast furnace research difficult but not impossible . The most serious obstacle in attacking the problem comes from the fact that it is useless in the design and operation of the blast furnace to use the method of " trial and error , which has proved valuable in so many other industrial problems . The variables are so interrelated and are so dependent one on the other that the number of experimental combinations to be tried is enormous . There are certainly not less than twenty factors in furnace operation and design that are known to influence the results . This is apparent if it is remembered that a phrase like " size and shape of the furnace" includes height of the furnace , height , diameter and angle of the bosh , inwall batter , stockline diameter , and furnace volume ; and that a phrase like " chemical and physical properties of the fuels charged " includes size and shape of the lumps , density, porosity and strength of the coke , in addition to its chemical analysis . Let us suppose that we need choose for each of twenty factors one of two values , for example , suppose we must say only that the furnace shall be " tall " or " short , " that the bosh angle shall be " flat " OF "steep , that the ore shall be " coarse " or " fine , " or that the blast has to be "hot" or " cold , " the number of resulting combinations is more than one million . In putting twenty pennies on the table , either heads up or tails up, the number of permutations possible is the twentieth power of two , slightly more than one million. It is obvious , therefore , that some sort of mathematical relationship , a set of rules of thumb , laws , curves or the like , are needed . Whether the relationships , curves or formulas are derived from experiment , from theory, or from mere guess -work, makes no difference provided they agree with the known facts . If they do not agree with known facts , they are worthless no matter what their origin or how weighty the " authority" vouching for them. Few such relationships have appeared in blast- furnace literature , and it may be doubted whether such formulas can be discovered .

Sep 1, 1923

By F. Matanzo

[Nine wire rope terminations were pull tested and fatigue tested to destruction to measure the termination efficiency and relative fatigue life. The terminations were selected on the basis off mine site visits and the specimen were assembled in a manner similar to industrial slings. To measure a termination&apos;s sensitivity to poor workmanship, both standard and modified assembly specimen were tested. Lang and Regular construction of the 6x19 and 6x37 class wire ropes were used in diameters of 13 mm (1/2 in.), 19 mm (3/4 in.), 25 mm (1 in.), 38 mm (1 1/2 in.), and 51 mm (2 in.). In static pull tests rope class, construction, and diameter interacted with the termination to influence the efficiency of the termination. In axial fatigue tests using only the 6x19 class rope, the effect of rope construction was negligible since failure was primarily dependent on the termination type. The Swaged Socket, a termination requiring a high capacity hydraulic press, gave the best overall performance in terms of efficiency and fatigue life. The short body length of the Zinc Poured Socket (RR-S-550) was attributed with the short fatigue life of this termination. The use of thermosetting resins as a replacement for zinc was demonstrated successfully for some socket designs. The fatigue life of the termination, expressed as a percentage of the fatigue life of the wire rope, was shown to be a guide for the retirement of the wire in these applications where the wiry&apos; rope is primarily in axial loading.]

Jan 1, 1978

By William C. Cooley

This study Identifies and evaluates deposits of noncoal minerals in the U.S. which are most amenable to be mined underground hydraulically and transported hydraulically. A method was developed to screen and compare mineral deposits including economic comparisons. The most applicable minerals for hydraulic mining by borehole monitor jets from underground entries are soft uranium sandstones In Wyoming in locations where water is available. This method with hydrotransport could improve the safety, health and economy of underground uranium mining. Soft oil-bearing sandstones in California and Texas could be mined and transported by this method more safely than by other underground mining methods. Other weak sandstones may be hydraulically mined economically. Man, minerals are too hard to be mined by monitor jet but are amenable to hydraulic transport and hoisting. Uranium sandstone in New Mexico is of interest because of potentially improved health and safety in transport and lower transport cost, Increases in mine output for potash, in New Mexico and trona in Wyoming can be achieved most economically by adding hydraulic hoisting when existing skip capacity is at its limit. Research is recommended to obtain site-specific data on the feasibility of mining uranium ores by monitor jets.

Jan 1, 1981

By K. K. Kelley

Thermodynamics data for silicates have applications in the fields of extractive metallurgy, ceramics, and geochemistry. To facilitate these applications, up-to-date tables of heats and free energies of formation are needed. It is the purpose of this report to supply such tables for anhydrous silicates. During the last 15 years the heats of formation of a substantial number of anhydrous silicates have been reliably determined at or near room temperature. This resulted from the development (first by the Bureau of Mines and later by the Geophysical Laboratory of the Carnegie Institution of Washington, by the Institute of Geology of the University of Helsinki, Finland, and by the Department of Geology of the University of Chicago) of accurate solution calorimeters, employing hydrofluoric acid as the reaction medium. Specific references to work of these laboratories will be made in the next section of this report. Also, entropy data at 298.150 K. and high-temperature heat-content values are available for many of these silicates, mainly owing to work of the Bureau of Mines. Most of these entropy and heat-content data have been compiled in Bureau of Mines Bulletins (13, 15).3

Jan 1, 1962

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By D. P. Schlick

The German experience in dealing with the health hazard of respirable dust in underground mines is reported from first-hand observation in this Bureau of Mines paper. The report covers-- 1. The control of dust by water infusion, water spraying, and ventilation. 2. The sampling devices (tyndalloscope , konimeter , and BAT-I) and methods used to determine the dust concentrations in mines. 3. The systems of classifying hazardous and safe dust levels in mines. 4. The research facilities devoted to theoretical and applied work on mine dust and pneumoconiotic disease. Tile major research projects on dust and disease now underway in West Germany are outlined in an appendix.

Jan 1, 1970

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By P. T. Brooks

Mineral nodules from the ocean floor represent a vast potential source of manganese, nickel, cobalt, and copper. Process development studies to devise methods for recovering these metals were conducted by the Bureau of Mines using two types of nodules--relatively low-grade calcareous nodules from the Atlantic Ocean and higher grade siliceous nodules from the Pacific Ocean. Ammoniacal carbonate leaching of reduced nodules appeared to have the best potential for processing the calcareous nodules, but the method proved to be impractical for recovering manganese. Extraction of 90 percent or better of the nickel, cobalt, and copper showed the technique to be attractive for recovery of these metals. The siliceous nodules appeared amenable to a process that starts with either a sulfur dioxide leach or a sulfation roast followed by a water leach to dissolve the soluble sulfates.

Jan 1, 1971

By William R. Archibald

This report presents the results of a program demonstrating the technical and economic feasibility of hydraulic borehole mining of uraniferous sandstone. This mining technique involves the drilling of a borehole from the surface down into the ore body. A borehole mining tool consisting of a high-pressure cutting jet and a slurry jet pump is lowered down the borehole. Water from the high-pressure cutting jet cuts into the sandstone formation generating a water-sand slurry which flows to the slurry jet pump and is pumped to the surface. The cutting jet is rotated and moved up and down from the surface, thereby generating a cavity in the formation. When the cavity size reaches a point beyond the effective radius of the cutting jet, the mining tool is moved to an adjacent borehole and the process is started again. This program was carried out in four phases. Phase I included modifications to the borehole mining system (built and tested under a previous contract, No. H0252007, for the mining of coal) and factory tests of the jetting system. Phase II covered the field tests and a public demonstration. Phase III involved nozzle and equipment modifications and factory tests. Field testing continued under Phase IV along with an evaluation of this method. The field tests were conducted successfully on Rocky Mountain Energy Company&apos;s Nine Mile Lake property near Casper, Wyoming. Results indicate that; hydraulic borehole mining of uranium is technically feasible (300 tons of uraniferous sandstone were mined from a depth of 90 ft) and the hydraulic borehole method is economically attractive. However, additional testing is required to clearly define the economic feasibility.

Jan 1, 1978