Search Documents

By Robert P. Bruno

This report covers the study of the feasibility of using a hand-held infrared viewer as a methane indicator to observe methane gas at the face of an underground coal mine. The objective of this program was the development of a hand-held device to remotely detect the presence of concentrations of methane gas in underground coal mines. Convenient "mapping" of methane from a remote location would allow rapid and safe corrective procedures for working personnel. Modified commercially available equipment was evaluated both in the laboratory and in a working mine. Although readings were obtained and the general principle of operation demonstrated, the power levels necessary, and protective enclosures required, would raise the weight of the instrument beyond practical limits of portability. Based on currently available technology, it is the conclusion of the investigations that a practical, portable, hand-held visual methane indicator is beyond the state-of-the-art. The recommendation was, therefore, made that work be suspended, and the results and data compiled and presented in a final program report.

Jan 1, 1979

This report summarizes the results of the Narragansett Win Projec't's activities during the U.S. Bureau of Mines (BOM) Phase 1, which was transitional from and which followed the National Science Foundation (NSF) Phase which initiated the investigation of New England's potential roil resource. The 960 sq. mile basin is structural and topographic lowland containing 12,000 to 20,000 ft. of terrigenous clastic sediments of late Pennsylvanian age, and which rests on an upper Precambrian and Cambrian basement. The Rhode Island Formation, which is the coal-bearing unit, comprising the bulk of the Pennsylvanian rocks consists, in order of decreasing abundance, of sandstone, conglomerate, silts tone, shale, and coal. In the NSF Phase, 24 drill-holes yielded 17,900 ft, of core; in the BOM Phase I study, 4 drillholes yielded 2,100 ft. of core. Anthracite and semi-anthracite was encountered in beds Up to 30 ft. thick in widely spaced parts of the Basin. The coal, typically very low in sulfur, and a high ash anthracite, won mined in substantial volumes from 1808 to 1959 from shaft and open lit in Portsmouth and Cranston, R.I., and in lesser volumes in Mansfield, Mass. Currently coal is now being mined in Plainville, Mass. as a fuel in the manufacturing of light-weight aggregate from the same quarry that serves as the source of the rock being processed. The structurally complex Narragansett Basin is now known to have a greater extent than earlier since recent drilling by others (Chapter 2) has confirmed our interpretation that the Basin extended offshore south A Boston. The, Basin also extends into Rhode Island Sound to the south. The geological structure is more complex in the southern part of the Basin than in the northern part. Three episodes of folding have been documented on Aquidneck Island and four episodes of faulting have been demonstrated for the Basin as a whole. Relatively less well exposed rock in the northern part of the Basin, increases the difficulty of recognizing and correlating structural episodes in the northern part of the Basin. The Basin his hewn subdivided into six structural domains which appear to have distinctive structural, metamorphic, paleontological and sedimentological differences that mw assist in isolating important events in the evolution of the Basin and its component parts. The tentative structural model recently developed in POP Phase I has important implications for exploration and mining. In the first and second folding stages the coal is mobilized and thickened in the crests and troughs of folds whose axes are horizontal to subhorizontal. While conventional coal exploration and mining methods are not applicable, great thickening in the crests and troughs of large scale structures, which can he defined by geology, geophysics and drilling, may provide compensating advantages. Bedrock over most of the Basin is 0-50 ft., but thicknesses of glacial deposits up to 150 ft. are present locally. Pro-Pleistocene topographic trends are controlled by structure and rock hardness; Pleistocene deposits aligned to the S. F. are superimposed on earlier trends. The southern part of the Basin is mainly dominated by high grade Barrovian metamorphism and plutonism of Permian age, related to the Alleghanian Orogeny. About 300 sq. miles of the 960 sq. mile Basin has been affected. The remaining 660 sq. miles, in the chlorite and subchlorite zones of metamorphism are compatible with the presence of high quality anthracite and semi-anthracite. Illite crystallinity studies begun in the NSF Phase, have been carried out in the BOM Phase l with important results. About ME of the northern Basin is now known to be in the diagenetic (unmetamorphosed) or subchlorite zone and the remainder in the chlorite zone of metamorphism. Mite studies, probably best recording temperature effects, show a generally progressive increase from the NW corner of the Basin near Plainville, Mass. toward the south and southeast. Reflectivity and coal petrography studies, probably best recording pressure and effects related to shearing, indicate a generally opposite pattern. Thus these methods provide powerful tools for the ultimate solution of problems important to coal exploration for coals of higher combustible volatile content and exploitation of these. Due to the complex nature of the coal, chemical data may not he easily used to determine rank. The coals have been tectonically deformed and mineralized. This deformation plus thermal metamorphism have altered the coals, in some cases by producing natural coke. Brecciated coal is often coated with a secondary depositional carbon. The coals' hydroscopic nature and high ash contents are due to the deformed nature of the coal and the presence of this secondary carbon. The stratigraphy and sedimentology of the coal-bearing Rhode Island Formation is similar to described alluvial fan deposits. The non-geological studies al-low three conclusions to be made: 1. A substantial number of areas have been identified in the Narragansett Basin in which mining could be carried out without undue difficulty from a land use point of view. 2. Substantially more than two hundred instances of past or current- mining activities have been identified in the Basin. Many of those are in areas defined as geologically interesting, and may be advantageous From the point of view of future exploration. 3. The map synthesis technique developed for this contract is successful and may easily be adapted to future exploration in its current form and also in its expandable form dealing with unit measurements of one-tenth mile. We recommend that BOM Phase 2 exploration should accomplish the intent of the Congressional language in House Report No. 95-1251, to continue a substantial drilling and geophysics program: "The Committee expects the Bureau to continue studies involved in ascertaining the extent and quality of low sulfur coal reserves in the Narragansett Basin in New England including necessary drilling and geophysical studies. The knowledge of the extent of such deposits is of great importance to this 'energy pour' area".

Jan 1, 1979

By Michael J. Beus

This Bureau of Mines report describes the development of load cells for measuring compressive loads in timber and lock-bolt support systems commonly used in. coal; metal, and nonmetal mines Design and evaluation is covered in detail to insure a reliable, accurate, and practical instrumentation scheme. The load cells are relatively inexpensive and adaptable to various size support systems. User-oriented procedures are emphasized, and design equations were reduced to a series of nomographs. Laboratory evaluation, destructive testing, environmental testing, and tests to determine the effect of extraneous loads were conducted. Field performance was evaluated in conjunction with ongoing Bureau projects at a metal mine in North Idaho and a coal mine in Utah. Load cells utilizing a titanium alloy as the cell body and weldable strain gages as the strain-sensing components satisfied the basic design and performance criteria, and with minor design modifications, the load cells can be adapted to many mining applications.

Jan 1, 1974

By Michael M. Hamilton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine mineral resources and resource potential in and adjacent to the North fork Smith RARE II study area. Most mineral resources identified in this area are in laterites, highly-weathered residual soil zones. In the RARE II area, resources of nickel, cobalt, chromium, and magnesium were identified at 15 laterite properties and chromium resources at one chromite mine. Other commodities include copper, gold, silver, and mercury (fig. 1). Approximately 1,100 lode and 1,200 placer claims have been located in or adjacent to the area. Most placer claims are for literites. There are no patented claims or mineral leases. Forty laterite deposits on 15 ,properties within the RARE II area (fig. 2) contain about 16 million tons of identified marginal reserves and subeconomic resources containing nickel, cobalt, chromium, an magnesium (table 1). Most deposits have keen explored and are currently claimed. California Nickel Corporation is developing laterites on Gasguet Mountain, within and adjacent to the southeastern and western parts of the study area. If this project proceeds to production, a laterite processing plant on Gasquet Mountain would enhance the minability of other deposits in the study area. The Climax, PFM, DF, and Stone Corral properties (fig. 1, nos. 1, 6, 9, and 23) have deposits of sufficient tonnage and grade to attract mining interest; resources at these properties are in and adjacent to the RARE II area.

Jan 1, 1983

By Anthony Iannacchione, Christopher Mark

Residents of Maxwell Hill, a suburb of Beckley, West Virginia, reported from January until March of 1988 a series of earth tremors. The tremors rattled dishes, and the noises associated with tremors were sometimes loud enough to wake people at night. These events were puzzling because Beckley is in an area of low seismic activity. Maxwell Hill is located above abandoned coal mines, though no direct subsidence damage to surface structures has been documented. A research program was initiated to determine whether subsurface ground movements associated with the abandoned mines could be responsible for the seismic activity experienced at the surface. A hypothesis is proposed which states that seismic disturbances can be caused by abandoned mine failure when two conditions are met. First, some instability must exist at the mine level. The most likely cause of instability is the failure of pillars of coal that were left for support at the time of mining. Second, subsurface movements can result in significant seismic activity only when the rock above the mine contains at least one very strong and brittle layer that is prone to fail violently through rupture or fault slip movement. Analysis of the data indicates that both hypothesized conditions for mine-related seismicity appear to have been satisfied in the case of Maxwell Hill. It has therefore been concluded that the earth tremors experienced by Maxwell Hill residents probably are related to the abandoned mines. Analysis of the potential magnitude of these events indicates that they are unlikely to cause significant surface danlage. The probability that future events will disturb the residence of Maxwell Hill should be quite low based on the identified mechanism.

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

1.1 DEVELOPMENT OF INDUCTANCE MATRICES The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available either from handbooks or from the manufacturer's published data. Thus, it is useful to summarize the derivation of the origin of the inductance matrix from basic principles. 1.1.1 Flux Around a Cylindrical Conductor The flux pattern around a cylindrical current carrying conductor can be found by using symmetry in conjunction with Ampere's Law. From symmetry it is clear that the flux lines which always close on themselves must be concentric circles. Thus, from symmetry alone one can get a qualitative picture of the magnetic field. This is shown in Fig. 1.1 where the inner circle represents the solid round conductor and the outer circle represents a flux line. The quantitative picture will now be developed using Ampere's Law.

Jan 1, 1973

By H. S. Auvil, L. D. Schmidt, H. G. Graham

"Several studies on the bulk density of coals prepared for byproduct-oven use were undertaken during the war by the Bureau of lanes in cooperation with the Office of the Solid Fuels Administrator and with the advice of the Coke Production Committee. The primary purpose of these studies was either to produce more uniform coke or to increase the throughput of existing facilities or both; the goal was increased Production of steel for war. As these studies were made, detailed reports were sent to the individual companies with whom the Bureau cooperated; also two reports,5/6/on the general subject of bulk-density control were published. In the course of the work, data were gathered that now prove of value in judging the merit of carious methods of testing bulk density and the limits of application of each method in byproduct-oven operations.Since the cessation of hostilities, the .Bureau section (Coke Production Survey Section) that conducted this work has been liquidated, but it was felt advisable to prepare a report on the accumulated experience so that it would be in a form available for the use of the industry and also as a base for any further research on the control of fluctuating bulk densities in coke ovens.It is hoped that the data and experiences recorded herein will be of material assistance to the many who have had difficulty in obtaining reproducible results in bulk-density testing. Since the data were gathered in the course of extending aid to individual plants in minimizing the deleterious effects of fluctuations in bulk density of oven charges on the quality and quantity of coke produced, certain desirable phases of an over-all investigation were not covered. However, on certain of these phases qualitative indications are available and the policy followed herein is that suggested by the American Society for Testing Materials Manual on Presentation of Data7/ that lacking quantitative information, relevant material should be included even though it ""may be qualitative in character, some may even be vague."""

May 1, 1946

By Anthony E. Szczuka

Two facets of surface mining were studied: feasibility of using training simulators to increase productivity of haulage trucks, front-end loaders, and shovels; and improving the efficiency of dragline operations with a computer-aided analysis of dragline usage and the addition of an on-board operator display. Training costs per student were estimated based on current training practices. Training objectives were derived from task: analyses of haulage trucks, front-end loaders, and shovels. The cost effectiveness of training simulators was determined. A computer-aided analysis defined the critical performance parameters. An on-board operator's display is recommended to improve operator efficiency.

Jan 1, 1976

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962

By Özgen C. Karacan

It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines. The spatiotemporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (C02) pore pressure were increased to keep a constant positive effective stress on the sample. The changes intemal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macro porosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlitho types and microstructures. The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the litho types present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the intemal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression. Keywords: Coal; Carbon dioxide; Sorption; Swelling; Sequestration; X-ray computed tomography; Volumetric strain; Gas outbursts

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By R. D. Saltsman

This report is in fulfillment of Contract No. H023001.5 awarded to Bituminous Coal Research, Inc., on November 15, 1972. The scope of the work under this contract was to perform a two-phase survey for the purpose of determining the status of work in the following specific areas of industry needs under the Technology Transfer Program and to increase industry's awareness of research efforts under the Federal Coal Mine Health and Safety Act of 1969 6f (P.L. 91-173): 1. Research and development of respirable dust sampling instruments which will more accurately collect the respirable Cuss as defined by the Federal Coal Mine Health and Safety Act of 1969. 2. Development of a better means of control of respirable dust and float dust.

Jan 1, 1973

By G. M. Martinez

The Bureau of Mines has investigated methods for the recovery of byproduct heavy minerals from sand and gravel operations in Oregon and Washington. These heavy minerals are not currently recovered except for gold in a few areas. The recovery of byproduct heavy minerals would provide a domestic source of minerals presently imported, and a more efficient use of domestic resources would be accomplished. Samples from more than 40 locations were treated by gravity separation to yield heavy mineral concentrates (black sands). Magnetite, ilmenite, zircon, rutile, chromite, platinum-group minerals, radioactive minerals and gold were identified in the concentrates. Individual zircon, ilmenite, chromite; magnetite, and gold products were recovered from selected concentrates by low-and high-intensity magnetic, high-tension, and heavy-medium separation techniques. The recovery for the individual mineral products ranged from 67 to 95 pct.

Jan 1, 1981

By A. Landsberg

Kaolinitic clays are potentially a vast domestic resource for aluminum. Utilization of this resource could decrease or eliminate the nearly complete dependence of the United States on foreign raw materials for this important metal. Furthermore, processing of clay to aluminum through anhydrous chloride metallurgy could reduce the high electrical energy requirements of the conventional Hall-Heroult aluminum reduction process. Several anhydrous chloride processes have been proposed; however, unresolved technical problems have prevented their commercialization. In particular, an acceptable chemical means has not been found to extract aluminum from clay as a highly pure anhydrous aluminum chloride. This Bureau of Mines report identifies and discusses the important chemical problems involved in achieving an acceptably rapid, self-heating, selective chlorination reaction and the subsequent separation of iron chloride byproduct from the anhydrous aluminum chloride.

Jan 1, 1983

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979

By N. A. Eilertsen

This paper presents the results of intermittent study begun in 1956 by the Federal Bureau of Mines of yieldable steel arches and yieldable steel ring sets installed for support of development openings in metal mines. Observations were made of this type of support in several iron mines in the northeast and north-central states. The sets, both arches and rings fabricated in the United States, are made from a hot-rolled, cold bent, structural U-shaped steel section in two weights, 15 pounds and 21 pounds per foot. The lighter section is generally used, It is 4.41 square inches in cross section area, and the calculation is that a 6-foot length of this structural shape installed as a supporting column, will safely carry the same load as a Douglas fir post of the same length but of 22 times the cross-sectional area of the steel.

Jan 1, 1962

By Mohan K. Wali

This report, the first in a series of 13 reports, provides a summary of 11 major topics on which individual reports have been prepared. These major topics are: (a) Nature of coal mine spoils, topsoils, and unmined soils; (b) influence of macro- and microclimate on (c) plant production on spoils and topsoils; (d) prediction of aboveground biomass from plant cover; (c) mineral composition of plants; (f) controlled environment studies on plant growth response; (g) microbial communities (h) water chemistry and organism diversity of catchbasins; (i) vegetation and soil development on abandoned, and (j) topsoiled sites; and (k) viability and diversity of seed bank. Based on these investigations, general conclusions and some recommendations are presented.

Jan 1, 1982

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984