Search Documents

By Xue Yongpeng, Zhu Zhenhai, Zhu Ming

The purpose of the Solid Medium Controlled Blasting Technique and Its Applications is to have the inside of the vessel-shaped framework (e.g: oil tank , water pool, gas chamber, chimney, water tower, grain warehouse and etc.) or the one side of the thin wall-shaped structure(e.g: steel bar concrete wall and etc.), both of which are intended to be demolished, inserted with the required solid medium (e.g: soil , sand , coal, salt and etc.) ,in which there is a certain mass density, and then through which the blasting energy is transferred to fulfill the blasting task. For such a technique, it is necessary to bury the explosives into the inserted solid medium and then to start the explosion to blast the intended target into pieces. The filling of the solid medium may be done mechanically or by man. Compared with the water pressure blasting technique, this one has the characteristics of good effect. wide application, simplified construction procedure , safe and reliable operation and small vibration (less vibration than water pressure blasting by 80% to 90%)in particular without any flying stones, thus resulting in better and comprehensive social and economickfficiency.

Jan 1, 2000

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By Benedict C. Di Duca

In the underground construction industry. when bidding work, not only is the contractor faced with determining if rock: is in existence within the parameters of his work. he must also estimate the quantity and the most efficient method of removal.

Jan 1, 1990

By Jack Eloranta

Proper selection of stemming has a profound effect on blast performance. This paper describes several methods of evaluating stemming performance in 16-inch blastholes. Tests are done on stemming ranging in size from nominal 1/4" crushed rock up to railroad ballast size rock (2 1/2" > diameter < 3/4"). Concrete plugs (both pre-cast and poured) are evaluated as well as air decking.

Jan 1, 1994

By John W. Kopp

The U. S. Bureau of Mines investigated flyrock and burden movement from blasting at several limestone and basalt quarries in the upper midwest. Blasts have been studied at 14 different sites using high-speed cinematography. Blasting was accomplished in 75- and 150-mmdiameter holes using a variety of explosives. Films from each blast were analyzed to show burden velocities, observed flyrock distance, and direction of throw in relation to the shot layout. This technique, in some cases, allowed determining point of origin and cause of the flyrock as well as the flyrock range.

Jan 1, 1994

By Conny Postnpaok, Mark E. Hammele

"A major problem that has continued to plague the surface oil industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through several years of field research in full-scale production environments. Many operations across the United States havebeen evaluated ."

Jan 1, 1989

By G Alan Foster

This paper discusses the cause of air blast and modern techniques to reduce this at the source. In addition it raises the problem of their marked variability due to prevailing weather conditions and how weather data can be obtained and used in the control of air blast.

Jan 1, 1975

By Othmar Mueller

Building demolition techniques using blasting are different depending on the structure of the building, on surroundings, traffic, debris-transport systems, and re-usability of salvaged building materials, etc. This paper outlines some of the trends and problems in demolition blasting technique in Europe and especially in Hungary.

Jan 1, 1975

By Michael Milstein

Northwest Research Station said as more and more older dams are removed to benefit fish, it’s become clearer that rivers rework themselves quickly.“Where the dam is relatively small, it’s a quick response,” he said. “The river quickly forgets.”

Jan 1, 2010

By Gordon Matheson, Bill Yancey, David K. Miller

"Current regulatory limits for blast vibration and airblast control in Virginia do not specifically addressunderwater explosive testing. Underwater detonation of explosives generates an initial shock wave and a gas bubble. The gas bubble expands and collapses several times before reaching the water surface. This expansion and collapse of the gas bubble as it rises to the surface is called a “bubble pulse”. The bubble pulse generates low frequency vibrations that have the most potential for damaging structures and causing blasting complaints even below damage levels."

Jan 1, 1999

By George Pittman, Dan McCutchen

When an explosive manufacturer in the USA wants to put a new explosive formula or detonator design in the toughest proving ground in North American, it is Florida. Florida conditions have baffled many creditable blasting experts. This paper deals with some of the methods used to overcome these problems.

Jan 1, 1995

By A. Spathis, I. Yacob, A. Labriola, G. Smith

Wall control is a significant issue for many mines. Improvements to the design process for blasts adjacent to temporary or final walls will require better measurement tools and predictive models. Orica Explosives has developed capability in both these areas and uses them to guide better wall control blasting practices. Vibration and gas pressure were monitored behind a series of production blasts and single hole blasts at the Freeport Grasberg Operations Opencut Mine. The blasts used ANFO in both 3 11 mm and 35 1 mm blastholes in a blast design which reduced the charge weight by between 30 to 50% in the final row of the production blasts. Single hole blast data were obtained by delaying the last hole in the production blast. Vibration levels were within the range often associated with vibration induced damage: 178 to 1080 mm/s at distances between 14-75 metres from the blast.

Jan 1, 2001

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By R C. Sittig

The manufacture of commerical detonating cord by the "wet process" technique is discussed. Raw material variability as a potential source of production problems is examined. Comparison to the "dry process" method is made. Inert samples, illustrating the cord's construction at various points in the production process, were distributed.

Jan 1, 1976

By Tuan Nguyen, Dirk Hummel, Ruilin Yang

In a tunnelling site in Japan, it was found that detonators failed to initiate with their shells and primary explosive intact. Their capacitors, however, were discharged due to some damage on the application-specific integrated circuits (ASICs). These detonators are distinctly different from other commonly observed failures, where the shells are rather crashed due to excessive dynamic pressure received from neighbouring blastholes which fired earlier. Such incident has not been reported elsewhere. Detonator failures during a blast are deemed not safe and can cause disruption on the project productivity. It is therefore desirable to understand the origin of such event. Various measurements were conducted to diagnose the problem, but the root cause had yet to be identified. This paper applies a discovery from a 60-year-prior-laboratory experiment and formulates a theory that could explain the observed detonator failure and predicts the measurements and observations.

Feb 6, 2023

By Carl R. Peterson, Robert G. Lundquist

The development of a remotely-controlled drill and blast excavation system is desirable both because it is potentially more economical than mechanical tunneling in hard rock and for safety. A serious impediment to such development is the problem of relocating and reentering previously drilled blast holes to place the explosives.

Jan 1, 1983

Lightning Strikes on Vehicles Transporting Explosives The police in one of the countries in which we operate has asked about the consequences of a lightning strike on a vehicle (box van) carrying detonators and explosives. We have assured them that there is not a problem but they require proof of this.

Jan 1, 2011

By Ruilin Yang

Techniques for the study of blast vibrations, such as monitoring, analysis, and modeling are often misused between near field and far field blast vibrations. This paper discusses the differences between near-field and far-field blast vibrations in terms of these techniques. A typical example of a near-field blast vibration problem is a blast vibration in the crest of a new highwall behind a cast blast. In such a case, the blast can be a couple of hundred feet long and the distance from the blast holes to a monitoring station may only be 100 feet or less. In this situation, the size or spatial geometry of the blast is not negligible compared to the distance from the blast to the vibration monitoring point. On the other hand, a typical example of a far-field blast vibration problem can be a quarry blast with a nearby residence house. In this case, the distance from the blast to the house may be several thousand feet. The size of the blast is less than a couple hundred feet long and negligible compared to the distance from the blast to the vibration monitoring point.

Jan 1, 2007

By Sarah Guzzelli, Enrigue Munaretti, Anneliese Botelho, Jair Koppe

Drill and Blast (D & B) is one of the main operations in the mining production cycle, which aims to fragment rock according to a pre-defined plan for proper loading, haulage and processing specifications. In this sense, data from a Brazilian iron ore mine was analyzed, given emphasis on blasthole length, subdrilling and stemming. The D & B report, including mining data such as number of blastholes, length, and diameter and stemming aspects, was analyzed in order to be able to compare these results with the blast design. The study showed significant differences between the designed blasting pattern and that one obtained by the operation. As a consequence, problems such as inadequate fragmentation, incorrect size distribution and loss of energy, were identified. For example, when stemming has a different length than it should have, noise and flyrock can occur, including inadequate fragmentation and vibration in both situations. Therefore, a comparison between the usual D & B procedures and recommended D & B design based on literature reveals the most important deviations and their consequences. The study intends to identify solutions for simple problems, improving D & B operations and safety practices.

Jan 1, 2014

By Martin L. Smith, Robert L. Hautala

The objective of blast optimization can be approached either in a qualitative sense of designing a blast which will be "trouble free", or quantitatively in the sense of minimizing overall mining costs. Blast design simulators and fragmentation models have become an accepted tool in blasting over the last decade. Numeric simulators are very useful for solving quantitative problems, but are limited in their ability to address more qualitative problems such as post-blast bench condition. Also, current blasting models are limited by the complexity of site-specific blasting and are not functionally suited to mathematical optimization. As a result a great deal of expertise is still needed in optimizing a blast. The following describes the application of an expert system approach to integrating both a symbolic model of the expertise of the blasting engineer for attaining a trouble free blast, and a numeric optimization model relating fragmentation to unit operations from drilling to grinding. Research into this application of a coupled modeling approach to blast design is being carried out to develop a modeling methodology which will provide a suboptimal design for qualitative design goals as well as minimizing blast related costs.

Jan 1, 1991