Search Documents

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by using electronic detonators. The Julius Kruttschnitt Mineral Research Centre (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast fragmentation measured with the SPLIT image analysis system to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed, and the powder factor increased, to maximize fines. However, a growing number of studies have shown that the use of electronic detonators can lead to increased fragmentation and greater muckpile uniformity, providing an alternate means of increasing primary breakage by blasting. Unfortunately results in the literature rarely quantified the changes to the fragmentation distribution. The measured gyratory crusher fragmentation of 2,750,000t of ore was used to compare stockpiles constructed from shots using pyrotechnic detonators to those using Orica i-kon electronic detonators. In the first stage of the study, stockpiles shot using 25 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using the same inter-hole timing with electronic detonators. In the second stage of the study, stockpiles shot using 17 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using 8 ms inter-hole timing with electronic detonators. When electronic detonators were used with the inter-hole timing kept constant, fragmentation uniformity was slightly increased, but mean fragment size increased by 20%. When electronic detonators were used with faster inter-hole timing, fragmentation uniformity was slightly reduced, but mean fragment size decreased by 30%. Modeling was used to determine the SAG mill throughput which could be expected from this change in fragmentation to determine the pairs of pyrotechnic and electronic blast pattern geometries that would provide similar throughput. The economic benefit from the electronic detonator shots was calculated to assist in determining the optimum blast designs for their use.

Jan 1, 2010

By Unknown

[Executive Director’s note: According to 17th edition of the ISEE Blasters Handbook in its section on trench blasting, “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underground and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or NOx may travel through the strata and find their way into basements of nearby homes or businesses. The IME has recommendations on how to minimize this potential problem. Some of the points include removing the overburden and digging the rock immediately after the shot, and drilling vent holes periodically between the ditch and adjacent homes.” The Board of Directors of the International Society of Explosives Engineers has expressed its concern that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. What follows are excerpts from “Carbon Monoxide - The Silent Hazard”, an article that was recently included in the Safety Update, Vol. 20, No. 1, 2001, published by Nobel Insurance Services.]

Jan 1, 2002

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

By Ian Bell

This paper investigates fragmentation in an aggregate quarry using the fragmentation-energy fan concept. Six blasts were monitored, located one behind the other in the same quarry area. The rock structure was blocky, the water level and the usage of explosives were variable within and between the blasts. The powder factor above grade was between 0.28 and 0.44 kg/m3 (0.47 and 0.74 lb/yd3). Fragmentation of the plant feed was measured using an online digital image analysis system and three belt scales. The oversize material that was not directly fed to the plant after the blast corresponds to 3‒9.3 % of the total. Data from image analysis was used to build the size distribution in the coarse range (fragments above 120 mm), and the passing fractions at 120 and 25 mm (4.72 and 0.98 in) obtained from belt scales data were used in the range 120‒25 mm (4.72 ‒ 0.98 in) . The non-dimensional percentile sizes between 10 and 90 % for each blast are described through power functions of the powder factor above grade; the model coefficients are statistically significant. From them, using the principles of the fragmentation-energy fan and the Swebrec distribution properties, the fragmentation can be expressed in terms of the powder factor by means of five parameters: the fan focus coordinates and the three parameters of a function of the exponents vs. the percentage passing. The model shows a good capability to describe fragmentation.

Jan 1, 2019

By Nikolaos Petropoulos, Ulf Nyberg, Daniel Johansson

A series of signature boreholes were blasted to observe any difference between confined and free face blasts. Four geophones were used to capture the compressive wave. The conventional approach, i.e. the calculation of vectorized peak particle velocity (vPPV) did not show any difference. Also a wavelet transform was tested.

Feb 1, 2020

By Eric Reale

The New York City Department of Environmental Protection (DEP) is currently building City Water Tunnel #3 beneath the city. The purpose of this tunnel is to improve water distribution to the city and to allow the DEP to inspect the older tunnels and make the necessary repairs. These older tunnels have been in continuous operation since the early 1900's. Construction on the Third Tunnel is planned in four stages. The Nelson Street Shaft, which is the focus of this paper, is part of the second stage.

Jan 1, 1989

By Marilena Cardu, Mauricio Dompiri, Jacopo Seccatore

Blasting in geological bodies is an industrial process acting in an environment characterized by high uncertainties (natural joints, faults, voids, abrupt structural changes), which are transposed into the process parameters (e.g. energetic transfer to rock mass, hole deviations, misfires, vibrations, fly-rock...). The approach to this problem searching for the “optimum” result can be ineffective. The geological environment is marked out by too many uncertainties, to have an “optimum” suitable to different applications. Researching for “Robustness” in a blast design gives rise to much more efficiency. Robustness is the capability of the system to behave constantly under varying conditions, without leading to unexpected results. Since the geology varies from site to site, and often from bench to bench on each site, setting a robust method can grant better results in varying environments, lowering the costs and increasing benefits and safety.

Jan 1, 2011

By Evan Jannoulakis, Wilfrid Comeau

Using the Scaled Distance (SD) and the vector sum Peak Particle Velocity (PPVvs) from a single delay, preferably single blasthole, in a shot, a number is derived which has shown itself to be consistently related to blasting efficiency, as experienced by one of the authors of this paper over the last thirty years. The numbers derived by this process range in value over one order of magnitude more or less. This variation, a function of distance, weight of explosive in the delay, blasthole diameter, blast design, powder factor and the geological environment, can be consistently related to two of these factors, powder factor and distance. In actual use the measured "BED" representing good blasting results should not vary by more than + 33 to + 50 percent of the estimated "BED" in non calibrated cases, and + 10 to 20 percent where previous experience is available. Relatively high "BED" values are indicative of poor blasting results while relatively low "BED" values may be precursors of poor blasting results in a shot. There are many variables in the geological environment which can affect the "BED". A case study is presented from a surface coal mining operation in eastern Canada. This case study tries to evaluate the reasons for the variability in "BED" values derived from multi-hole shots. A problem in using "Signature Vibrations" from a single-hole shot to predict blasting vibrations from multiple-hole production shots is identified.

Jan 1, 1998

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By Robert Hopler

209. Nitro-glycerine is produced by the action of nitric and sulphuric acids on glycerine, and is a heavy liquid of oily appearance, of specific gravity about 1•6, varying from colourless when quite pure to a yellow or brownish yellow. It is of a very sweet taste, and without odour, and is an active poison. Mere handling of it will in most persons induce sickness and headache. It explodes when heated to about 360° F. or from shock, but in small quantities it ignites and burns with some difficulty by the mere contact of flame.

Jan 1, 2011

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By J. Sigler

A series of small scale tests have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite were tested. The charge configurations included detonating cord placed in five holes with water as a coupling medium or concentrated charges of equal mass, placed in the same number of holes, fully stemmed or air decked. The powder factor was varied from 0.4 to 1.2 kg/m3. Typically all charges were detonated simultaneously; however, in some experiments, detonation waves collided in the middle of each borehole and in others a small delay was used between charges. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using a standard Bond mill arrangement. The experiments generally showed increased softening of the rock with powder factor, which appeared to be the dominant factor. Charge configuration as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2008

By Javier Illanes, Felipe Moroni

In recent years, implementation of Artificial Intelligence and Machine Learning model technology has gained ground in almost every aspect of human activities. The mining industry has not been foreign to these applications, with advantages including the creation of new optimization methods and the elimination of repetitive tasks. Those applications have been implemented in multiple operative areas, from preventive conveyor belt maintenance to energy optimization for minimizing environmental impact. The blasting process aims to use the energy liberated by the detonation of explosives to break the rock mass according to specifications that facilitate the comminution process. To optimize this process, the energy delivered must correspond to the necessary amount to exceed the tensional and compressional resistance of the rock mass. If the energy applied is insufficient, the rock will not reach the desired fragmentation level and the processing plant may incur additional costs. On the other hand, if the energy level required is exceeded, we incur increased blasting costs that correspond to excess explosive used. Optimization of this aspect of the mining process has major impact in the processing chain reflected in lower costs, efficient resources consumption and environmental impact. The Design for Outcome technology (DfO), developed by Orica, is used to characterize the rock mass in detail to classify, borehole by borehole, the rock mass relative hardness to deliver the adequate energy level to achieve optimal fragmentation. This technology uses information collected by drill sensors, producing data typically referred to as Measure While Drilling (MWD) data to classify the rock mass into domains that can later be used to apply optimal blast designs. In DfO, the data flow is fully automated, starting with the data produced by the drilling system and uploaded to the cloud, which is then domained using Machine Learning (ML) techniques, and then published for consumption using a web interface. Automated explosives loading rules are then generated for each rock mass domain, ensuring that for each borehole, the adequate explosive energy is delivered to achieve the desired fragmentation results with unprecedented accuracy. The application of machine learning techniques allows us to optimize the blasting process results by leveraging a deeper understanding of the rock mass. Applying these optimization techniques, we obtain considerable economic benefits, decrease resources consumption, and achieve a more sustainable mining operation. The application of DfO in a Chilean mining operation allowed the characterization of their rock mass into four domains and established specific explosive loading rules for each one. A 60kUSD reduction in explosives cost was achieved during the test period, while maintaining the desired fragmentation results and expected dig rate. These outcomes were the result of a comparison between the blasting costs used applying the technology mentioned above and a “traditional” classification of the rock mass with the corresponding blasting practices.

Jan 21, 2025

By John W. Brown

During the summer of 1994 the mining industry experienced numerous accidents involving blasting related incidents. The Tri-State Chapter of Explosives Engineers planned a meeting to discuss three of these accidents.

Jan 1, 1995

By C. Zuniga, S. Combrinck, C. Peters

Agnico Eagle Gold have partnered with Enaex Australia at their Fosterville gold mine to leverage a combination of drill and blast technologies to optimise underground development mining. The mine is the first site globally to collaboratively develop and trial Enaex SWIFT electronic development detonators, which utilise a novel approach to the user interface, simplifying implementation and enabling the benefits of electronic initiation without the complexity of a conventional system. This has been combined with the use of a Sandvik 422i smart jumbo, and the Enaex underground emulsion charging unit with the capability to tailor the delivery of explosives as required and report on a hole-by-hole basis. The combination of these technologies enables full engineering oversight of the development cycle, in turn enabling optimisation of this process in a historically conservative application. The methodology for leveraging these technologies is to bore a controlled and defined blast pattern through using a smart jumbo, load the blast holes utilising lace loading to deliver a desired quantity of ammonium nitrate emulsion per hole, with the ability to reduce chargeweight for perimeter control, and utilising Enaex SWIFT electronic detonators with flexible template type pre-defined delays to initiate the blast holes. Subsequent to firing and excavation the performance of the blast in fragmentation, advance efficiency, and overbreak and underbreak is measured and reviewed. This is then used to optimise the development cycle and apply to other parts of the mine.

Feb 6, 2023

By Cory Loukides, Cathy Aimone-Martin

Blaster training manuals used by the Office of Surface Mining (OSM) and others are outdated and cumbersome. A new approach has been developed using Microsoft PowerPoint with a Visual Basic overlay to produce modules on CD’s that present state of the art blasting techniques. The education modules contain enhanced information on topics such as explosives and initiation products, blast design, drilling, and vibration control. The content is based on safe practices and illustrated with numerous photographs and movies. Review questions, complete with explanations for incomplete answers, enhance the learning process and keep the blaster involved. The benefits of using an electronic format include the ability to continually change and update the training modules as new products, technology and applications become available. In addition, the blaster can work at home in preparation for class work and may reduce the time away from the job. This poster session presentation will allow potential users to view and take part in the evaluation of these modules.

Jan 1, 2004

By Erica Lorenzo García, Benjamín Cebrian Romo, Antonio Morato Medina

This paper presents the results of a preliminary study on blast-induced vibrations conducted at a Radioactive Waste Storage Facility, located in Spain. The study was undertaken as a preparatory step prior to the blasting operations required for the construction of a new platform located near critical infrastructure housing very-low, low and intermediate-level radioactive waste. The primary goal was to establish a site-specific vibration attenuation curve to safely determine allowable explosive charges based on their distance to sensitive structures. The study followed the criteria defined in the UNE 22.381-93 standard, which regulates permissible vibration levels for different structural typologies. In this case, the existing facilities were classified as Type III structures, given their heightened sensitivity to vibrations. Two experimental campaigns were conducted. Test 1 consisted of a series of 10 individual blasts with increasing charges, monitored by five strategically placed seismographs to record seismic wave propagation and determine the attenuation parameters via regression analysis. Test 2 simulated a production blast using operational charges of 41.7 kg (91.93 lb), applying different delay sequences (42 ms and 25 ms) between holes to assess wave interference, resonance, and constructive effects. Data analysis showed that the longitudinal component dominated vibration transmission, and the predominant frequencies in the most critical zone ranged between 18 and 20 Hz. Based on these values, a conservative peak particle velocity (PPV) limit of 4.75 mm/s (0.19 in/s) was established for blast design. The recorded vibration levels during the tests remained within regulatory limits, with maximum values of 2.35 mm/s (0.09 in/s) and 2.86 mm/s (0.11 in/s) for the sequenced blasts, and peak acceleration of 0.0464g.

Jan 26, 2026

By J. Eloranta

"Previous work indicated that the annual per-capita consumption of raw aggregate material averages about 10 tons; half of which is produced by blasting. Given a population of approximately 320 million in the United States alone, this amounts to 1.6 billion tons of blasted material annually. It was also estimated that up to 20% of the blasted material in aggregate operations is smaller than 6.35 mm (1/4inch) in size. Thus, about 320 million tons (i.e. 1 ton per capita) of byproduct is produced annually and sold at significantly lower prices or potentially discarded in waste dumps."

Jan 1, 2017

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera. The burning process of the aluminized emulsion explosive has been modelled with the ignition and growth (I&G) flow model in the LS-DYNA code. A routine based on the optimization program LS-OPT code was developed to identify the parameters in the burning rate function with the detonation velocities and the front curvature radii from two tests. A Perl code was implemented in the routine and was used to calculate the VoD, fit the detonation front and obtain the detonation front curvature radii. The calibrated parameters were used to predict the VoDs and the detonation front curvature radii for the rest cases. The results indicate that both the VoDs and the detonation front curvature radii from the numerical modelling are in good agreement with the experimental results. The numerical results also indicate that the variety of the burn fraction and the peak pressure with the change of charge diameters is reasonable with the calibrated parameters.

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera

Feb 1, 2020