Search Documents

By Marcia Harris, Richard Mainiero

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Jan 1, 2004

By Jason Rock, Rob Thompson, Lee Julian

Reactive ground is ground that undergoes a spontaneous exothermic reaction after it comes into contact with nitrates. This is commonly caused by inert rock hosting sulphide minerals, such as pyrites that act as the reagent. The presence and subsequent rate of reaction with nitrate based bulk explosives can be difficult to predict. Once identified, only explosives that are tested and proven to be compatible with the reactive ground may only be used. These typically take the form of inhibited ammonium nitrate emulsion blended with a limited volume of ANFO or porous prilled ammonium nitrate (PPAN) to ensure that all AN prills in the blend are wholly encapsulated and thus protected from the reactive ground. The requirement for high emulsion content bulk products limits the suite of products available for use to high energy, and high expense products. Further, if chemically sensitised products are used, charged holes must be left unstemmed to allow for gassing to occur, adding delay and exposing the blast crew to an unconfined charge in reactive ground. A range of inhibited products has been developed that are solid sensitised and can be bulked to as low as 0.9 g/cc (56.2 lb/ft3). The use of a solid sensitiser enables stemming to occur immediately after each hole is charged, confining any unplanned detonation more safely within the rock mass. The effective and precise manufacture of bulked inhibited products required a new and innovative Mobile Processing Unit (MPU) design. This MPU required the ability to blend two solid raw materials (AN prill & sensitiser) along with two liquid ingredients (AN emulsion and process fuel). This MPU has been designed, manufactured and has used successfully to manufacture low density inhibited explosives. This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

By Ann Barron, Paul Downing

Those employed in the explosives industry must have a keen familiarity of the explosives products they handle, the safety pro c e d u res they must follow, and the increasing number of laws and regulations governing blasting operations in order to perform their duties satisfactorily. For this reason, companies must make certain that their employees have the necessary knowledge and full understanding of their blasting and non-blasting responsibilities. Consequently, training is one of the most important elements in any company’s safety program.

Jan 1, 2004

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Remi Proulx, Ruilin Yang

The effectiveness of presplit in soft or fractured ground is hard to visualize or quantify. There have been many attempts by the blasting community to measure and quantify the effectiveness of presplit blasts. Various methods have been adapted by different researchers, and the results are debatable.

Jan 1, 2019

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By Tie-jun Tao, Ming-sheng Zhao, En-an Chi

"Karst landform is a special kind of geomorphic unit which is often accompanied by a large number of geological defects: caves. In blasting engineering, if there are karst caves around the blast-holes, it may result in higher boulder yield and the generation of flying rocks due to the change of burden which is very hazardous for the safety of surroundings. The models of rocks with karst caves from blasting holewere built by the software of ANSYS/LS-DYNA. The results of computation simulation show that thecave can increase more free surface for blasting and leads to a broken zone around itself. Thus rockmass around the cave will fly toward inside and it will result in undesirable result of whole rock mass to be blasted. In addition, the models of rocks with karst caves in different shapes were simulated and thecomputation results show that the caves in round shape have higher load resistance capability than that the caves in rectangle shape. All the simulation results can offer effective guidance for blasting design. The models of rocks with karst caves were built in different distances and shapes from blasting hole by the software of ANSYS/LS-DYNA. The effect of different karst caves on blasting stress and blastingresult were studied."

Jan 1, 2017

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

According to the Directive 93/15/EEC, given on 5th of April 1993, all the commercial explosives placed on the market and transfered in European Union and EFTA countries have to be certified and contain the CE-marking. Before the products can be awarded by the CE-marking they have to fulfil the Essential Safety Requirements (ESR) of Appendix 1 of the Directive. From the beginning of last year the commercial explosives could not have been be sold in Europian Union countries without the CE-marking. The legitimacy of the Directive 93/15/EEC encompasses High Explosives, Detonating Cords, Safety Fuses, Gun Propellants and Detonators. At the moment in Europe, there are seven Notified Bodies (NB) working in the field of commercial explosives. They are in Spain (LOM), Germany (BAM), France (INERES), England (HSL), Netherlands (TNO-PML), Sweden (SP) and in Finland (PvTT). The Swedish SP has qualifications only for the detonators and the Finnish PvTT for High explosives, Detonating cords, Safety Fuses and Gun Propellants, but not for the detonators. The role of the NB is to work as a third independent body between the client and the manufacturer testing, studying and certifying explosives by the commission of the manufacturer. The Notified Bodies are operating independently competing the clients, the explosives manufactures.

Jan 1, 2004

By Matias Suarez, Diego Zenteno

This paper is aimed to display the new advancements of blasting engineering done in different mining sites throughout the country, associated to electronic sequencing, energy of the explosive and its impact on the fragmented rock. This document explains how to define and implement selective sequencing in the blasting in order to promote the propagation of cracks, therefore impacting positively the productivity through the use of the LaGrange diagram. The LaGrange diagram is a very convenient and illustrative method to present the dynamic behavior associated with wave and crack propagation (Rossmanith. H, 2002).

Feb 1, 2020

By Matias Suarez, Diego Zenteno

It is known that the introduction of electronic timing in the sequencing of blasting has changed the vision and way in which mining is developed. It is possible to deal with more complex and sophisticated drilling designs, without compromising productivity or safety. It has been shown in various studies, that a correct timing of the blasting provides an improvement in the improvement of the processes downstream, due to a decrease in the resistance of the resulting fragments coming from the interaction of the waves generated in the detonation of explosive loads. On the other hand, it has also been shown that variations in the composition of a same type of explosive, has a significant influence over the resistance of the blasted material, also the energy associated to break it, affecting directly its degree of fragmentation. This paper is aimed to display the new advancements of blasting engineering done in different mining sites throughout the country, associated to electronic sequencing, energy of the explosive and its impact on the fragmented rock. This document explains how to define and implement selective sequencing in the blasting in order to promote the propagation of cracks, therefore impacting positively the productivity through the use of the LaGrange diagram. The LaGrange diagram is a very convenient and illustrative method to present the dynamic behavior associated with wave and crack propagation (Rossmanith. H, 2002). This study focused on the methodology of the formation and measurement of seismic pulses, through the rock massif. For this purpose, seismic pulses were acquired in the field and then, the different dynamic phases of the wave were molded mathematically, with the purpose of favoring the coupling between them.

By Peter Duniam, Vivian Patz

History of the ExEx 1000 CAB system. l What we’ve learned using electronic timing. l Requirements for a second generation. EDD system. l The ExEx 2000 system - simple, versatile and cost effective

Jan 1, 1997

By Paul Sairato, Cathrine E. Johnson

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. This paper provides the data from a second, restructured, online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2015

By Kirk Yeager

All explosive formulations display some sensitivity to heat. A common technique utilized to measure an explosive’s response to thermal stimulation is differential scanning calorimetry (DSC). As DSC analysis is run on quantities of material easily handled in a laboratory setting, and is relatively inexpensive, it tends to be one of the more predominant tools utilized to determine potential thermal hazards of energetic materials. The analysis of energetic materials via DSC provides unique challenges, as both large energy outputs and significant production of gaseous products result from their decompositions. In addition, the unique thermal decomposition characteristics of ammonium nitrate (AN) based materials have also created difficulties in DSC analyses. A wide variety of techniques have been developed to study the decomposition of explosives. Traditionally, sealed glass capillaries were utilized to house samples. Recently, the introduction of specialty cells designed to withstand high pressures has enabled new sampling techniques to be developed. Analyses of explosives with both traditional and “high-pressure” cells will be compared and contrasted. Lessons learned about the application of both techniques towards analyzing thermal hazards such as incompatibilities will be presented. Inconsistencies in the results displayed during analyses of AN-based explosives will be highlighted. Recommendations on the best approach for analyzing the more problematic AN formulations will be given.

Jan 1, 2000

By Claude Cunningham

AEL has been developing electronic detonators continuously since 1986. It launched its first system for opencast mining in 1993, and now has two distinct product lines. The path has not been without great difficulty, but the determination to persevere was always buoyed by the strong encouragement of customers who experienced the transformed blasting results, as well as a clear vision of the enormous intrinsic value of the concept. The path of growth to dominant global supplier is traced through the separate application channels of coal stripping, quarrying, massive mining, opencast mining and narrow reef mining, to the first allelectronic detonator demolition blast in June 2001. Reasons for the slow coming to market of this highly desirable concept, which often coincide with reasons for the demise of various other systems, include the difficulty of safely mating electronics and explosives in a low cost environment; the extreme difficulties of achieving proper connection under mining conditions; the rapid rate of evolution of the technology, and the safety concerns raised by various accidents and incidents along the way. ED.s are now established as the way forward and are set to displace other systems in all serious applications. There is place for both programmable and pre-set delay systems.

Jan 1, 2002

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"The United States (U.S.) Department of Homeland Security (DHS) Directorate of Science and Technology (S&T), utilizes a probabilistic risk assessment (PRA) approach to explore the risks (anduncertainty) from chemical, biological, radiological and nuclear (CBRN) threat agents to the Homeland.This end-to-end risk methodology considers a broad range of hazards incorporating emergingtechnologies, available countermeasures and input from the Intelligence and Law Enforcementcommunities (IC/LE) to evaluate the acute risk to human health due to an attack on the U.S. homeland. The PRA generated output provides a mechanism to examine risk mitigation strategies, critical vulnerabilities, critical data and knowledge gaps and relative risk rankings of materials, targets, classes of compounds and scenarios."

Jan 1, 2017

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By R. Narendrula, S. P. Singh

The productivity of a loading machine is affected by several factors. One of the most significant is the characteristic of the muck being loaded. A study was conducted to examine the effects of the looseness, angle of repose, size distribution and moisture content of the blasted material on the efficiency of the loading machine. The study was conducted in the following stages: (a) controlled experiments in the lab, (b) tests with loader simulator and (c) field work in an operating mine. It was found that looseness (%void) in the muck increases with the increase in the value of the mean particle size and index of uniformity of the fragmented rock. Looseness and angle of repose affect the fill factor and the digging cycle time of a loader and in turn the productivity of the equipment. Moisture content affects the angle of repose as well as the stickiness of the material to the loader’s bucket. It was observed that the angle of repose increased with the increase in the mean particle size and the moisture content of the muck. It was also found that the bucket full factor and rate of scooping decrease with the increase in the values of mean particle size and index of uniformity. This was also conformed during fieldwork that bucket fill factor decreases with the increase in the mean particle size as well as the index of uniformity.

Jan 1, 2005

By Neal Lee

Reduced relief horizontally means an increase in energy expended vertically into the rock surrounding the stemming column, and potentially through the stemming column. The vast majority of holes in any surface blasting operation are afforded two horizontal relief faces at the moment of firing, whether by existing relief faces in front of and to one side, or previously blasted hole(s) in front of and to one side of the holes in question. When the energy expended in any hole on the blast pattern has less than two Horizontal Relief Planes or faces (referred to moving forward here as “HRPs”) available to it at the moment of firing, a higher percentage of the available energy is directed vertically. In the analysis of recorded videos by the author, one will note the fact that stemming ejection/flyrock is observed to a much greater degree from the center of almost all patterns when they are timed to “pull out of the middle” (“box cut" timed patterns). This is because the first hole to fire in each row has only one Horizontal Relief Plane, which significantly decreases horizontal avenue for energy release for these holes. This of course results in an increase in the amount of energy expended vertically. This paper proposes a novel methodology to modify the stemming to better use the explosives energy of each hole, while controlling side effects such as flyrock and airblast.

Feb 6, 2023

By Max Pena Woolcott, Winfried Rosenstock, Maria Chappuis, Walther Hennig

"In a Peruvian-German Technical Cooperation project for the Mining Sector the ""Milpo-cut"" along with the electric initiation system has been successfully implemented in a Peruvian metal-ore mine.Specific savings in drill work and explosives consumption up to 50 % have been achieved in headings and slopes. The positive results have motivated further Peruvian mining companies to introduce the new technique."

Jan 1, 1994