Search Documents

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Industrial minerals may contain the same elements in approximately the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques.• quantitative measurements by ebsdCommon automatic techniques describing the mineral contents and the occurrence of minerals in free and locked particles, are based on optical-, backscattered electron (BSE)- or X-ray-signals. There are various commercial software systems on feature analysis by backscattered and X-ray signals in combination with image analysis (e.g. Oxford Inca Feature, CSIRO QemScan).Especially in silicates, the occurrence of similar elements in the different minerals is common. Sometimes the various minerals not only contain the same elements, but also approximately the same amount of each element. In these cases BSE imaging and chemical analysis are not always sufficient for identification."

Jan 1, 2003

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By Dominic Howarth, Diana Drinkwater, Don McKee

At a time when the mining and minerals industry across the world is undergoing unprecedented change, the very fabric of the tertiary education system which is the principal source of trained professionals to the industry is in decline in many countries. The change sweeping the industry is globalisation as evidenced by the emergence of a relatively small number of increasingly dominant corporations with operations in most of the major mining countries. The education sector is struggling to provide sufficient graduates as the viability of small mining schools declines. That is only part of the problem as the global operating industry is increasingly seeking graduates who are comfortable working in different countries and cultures. One obvious response to the industry needs and developments is for the education sector to consider how it can best respond to the global opportunities. This paper presents the case for a global education network which is based on a network of international thinking Universities and which makes use of the latest in educational thinking and technologies to provide a quality education and in the process produce graduates fitted for international careers.

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003

By Elena L. Chanturiya, Vladimir A. Bocharov, Roman A. Amosov

"In many volcanogenic base metal deposits of Russia the gold is closely associated with copper sulphides and pyrite. The recovery of gold associated with pyrite is especially difficult problem.Investigations of gold chemical state and mineral forms in copper-zinc sulphide ores of Gay and Barsuchiy Log deposits in the Urals have been made using EPMA, optic image-analysis, XRA, SEM, thermo-electrical force measurements and selective gold leaching experiments.Two gold varieties are determined: 1) free native gold particles (from 5 µm up to 0,25-1,0 mm), which can be liberated after grinding of ore up to 0,074 µm and named “free gold”; 2)”invisible” gold, including finely disseminated native gold and chemically bound gold. The second variety can’t be disclosed during grinding. Free gold can be recovered by gravitation and flotation while the processing behaviour of “invisible” gold is determined by properties of gold-bearing sulphides: pyrite and chalcopyrite. According to results of diagnostic leaching experiments in ores of deposits mentioned above the part by weight of free gold reaches 70%, the part by weight of the ”invisible” gold is up to 20%. About 10% of gold is enclosed in quartz and acid-soluble minerals.Theoretically (taking into account gold distribution data) it’s may anticipate gold recovery by gravitation up to 60%. However after grinding up to 50-60% of class –0,074 mm only about 40% of gold passes into oversize product including 30% of free gold and 8% of ”invisible” one. It can be recovered by gravitation. Remaining free gold and ”invisible” gold can be extracted by flotation – 25% in total. Inevitable gold losses in tailings may reach 8-10%."

Jan 1, 2003

By Eberhard Gock

The worldwide implementation of corrosion protection of low alloyed automotive metal sheets by zinc coating has led to supply shortages of zinc free non-alloyed steel scrap in the foundry industry. In a collaboration project, partly financed by the German government, with partners from the automotive industry, zinc metallurgy, scrap trading, foundry industry, and plant construction, a new acid-based pre-dezincification process has been developed, and a pilot plant with throughput of about 100 t/d has been put into operation at the Clausthal Umwelt-Institut GmbH (CUTEC) together with the Clausthal University of Technology in Germany. During the treatment process, acid from a zinc metallurgical plant will be supplied, which can be recycled to the primary zinc extraction process after raising the zinc concentration to more than 130 g/L zinc. This way, the separation of small amounts of iron by precipitation and the electrolytic zinc winning are outsourced and, as a result, the pre-dezincification process runs waste-free. In Germany, the amount of zinc coated ?new scrap? is approx. 3 million t per year with a zinc content of approximately 60,000 t per year. The possible additional incomes for the dezincified steel scrap are in the order of ?40 to ?50 per ton of scrap, the gained zinc content during the acid dezincification defrays the costs of the process, if the throughput is more than 700 t/d. In comparison to conventional dezincification during the electro arc furnace process followed by upgrading in a rotary kiln (Waelz process), the acid dezincification process running at a maximum of 50°C will cut the energy costs by up to 74% and the CO2 emission by up to 88%. In fact, a demonstration plant is being designed right now and will be installed for processing a part of the zinc coated metal scrap from the Volkswagen AG in Wolfsburg, Germany. Keywords: steel scrap, zinc-coated steel, dezincification methods, acid

Sep 1, 2012

By K. H. Luo, J. Y. Liu

An experimental study on interparticle breakage of three iron ores was carried out by compressive stressing of particle-bed in a piston-die device. The feeds to the particle-bed stressing were five narrow size fractions in the size range of 0.2~3.2 mm respectively and a wide size fraction of 0/4.0 mm. The pressures applied were in the range between 30 and 360 MPa. The results show that the energy absorption of the particle bed increases linearly with the pressure; the increase of the product fineness with the pressure declines as the pressure goes up; and the product size distributions resulting from interparticle breakage of different narrow size fractions have no self-similarity. Using data obtained from the piston-die compressive stressing test, the suitability of a previously-developed material-characterization model for interparticle breakage was verified for these ores. It is shown that the particle-bed compression test conducted with piston-die device in lab-scale may provide a cost-effective way of studying and modelling size-reduction of ore materials by interparticle breakage.

Jan 1, 2014

By A. De1

Because of the extremely low utilization of strain energy in the breakage of solid particles, the energy efficiency prevalent in comminution technology is extremely poor. Schoenert considered that single-particle comminution under slow compression is the most energy-efficient mode of comminution and that energy efficiency should be compared to that. The usual method for grinding minerals and cement has been the ball mill, in which the hit-and-miss aspect of loose-bed comminution severely reduces energy efficiency. The fine grinding of minerals is a particularly energy-intensive process. Schoenert showed that the energy consumed in the comminution of particles in confined beds is second only to that of single-particle comminution under slow compression and developed the method of conducting particle-bed comminution continuously in a high-pressure roll mill. Since its first industrial installation in 1985, the high-pressure roll mill has established itself as the comminution device of choice for significantly improving the productivity and energy efficiency of size reduction from coarse size feeds down to products finer than 20 microns. The first of several hundred installations were in cement plants. The preliminary design and optimization of the industrial operation of high-pressure grinding roll (HPGR) systems, owing to the continuous nature of the device, cannot be efficiently done through laboratory experiments and needs to be achieved through proper system modeling. While the energetics of size reduction in high-pressure grinding rolls has been modeled very well, no model exists for the macroscopic variables in HPGR comminution. In high-pressure roll mill grinding, size reduction results from confined particle-bed comminution under compressive stresses such that the daughter particles produced are highly fractured, stressed, or otherwise weakened. This paper attempts to relate the comminution / compaction behavior for confined particle-bed under compression in a piston-die press with the macroscopic variables in HPGR comminution. A model describing the pressure-densification relationship is presented and used to accurately simulate the macroscopic variables in high-pressure grinding rolls, utilizing experimental data for particle-bed comminution with the piston-die press. The accuracy of the predictive simulations strongly suggests that, starting with a few batch-mode laboratory-scale experiments, it should be possible not only to identify the optimal operating conditions for existing operations but also to successfully design new industrial high- pressure grinding roll systems.

Sep 1, 2012

By V. V. Lvov, L. S. Chitalov

"The purpose of the research is intensification of physico-mechanical ore properties determination for ball grinding processes in comminution circuits. The research presents comparative studies aimed at intensification of Bond Ball Mill Work Index (BWi) determination, such as testing technique of Ahmadi and Shahsavari, Berry and Bruse, Gharehgheshlagh, Horst and Bassarear, Kapur, Magdalinovich. The subject of the research is a test procedure of apatite-nepheline, copper-nickel, gold-sulfide and iron ores for the Bond ball mill index. The Bond Ball Mill Work Index for the material firstly was determined by standard Bond test methodology. Two the most promising testing techniques - Ahmadi and Kapur testing techniques - were modified. For the Ahmadi technique it was proposed to pay attention to the circulating load, which should be stabilized on the value of 250% as fast as possible. Two methods were put forward to quicker stabilize the circulating load. For the Kapur technique it was proposed to use empirical coefficients, which is determined especially for the apatite-nepheline, copper-nickel, gold-sulfide and ores. The modified Ahmadi and Kapur techniques require no more than two cycles of ball grinding to determine BWi (while normally 6-8 cycles are required) and less than 5 kg of initial feed. The suggested modified Ahmadi and Kapur techniques allow to intensify the physico-mechanical ore properties determination for ball grinding processes and BWi test costs considerably, which makes them useful for mass sampling and monitoring strength properties of ores entering a concentrating mill. INTRODUCTION When designing concentrating mills, the choice of the technological scheme for ore pretreatment, particularly the type, quantity and size of the main process environment, the determination of optimal grinding conditions and the calculation of equipment load are carried out by preliminary studies of grinding in semi-industrial or laboratory-scale plants. Semi-industrial tests on full-scale plants provide the most reliable information for calculating specific loads for equipment. However, this requires a significant amount of ore samples, a high labor costs and the pilot plants. Thence the most researchers performed grinding tests with small laboratory equipment using small ore samples."

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, M. Zare

High Pressure Grinding Roll (HPGR) plays a major role in increasing specific surface area of iron ore concentrate for producing pellet feed. HPGR grinding mechanism implies that material be compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study for determining a simple relationship between material pressure resistance ability and HPGR main design parameters, piston press tests were performed on different iron ore concentrate samples along with HPGR Blaine increasing tests. Piston press tests results showed that by decreasing moisture content, material pressure resistance increased and in constant moisture content this parameter will change based on material specifications. HPGR Blaine increasing tests results showed that by decreasing moisture content, HPGR specific throughput and working gap increased and in constant moisture content this parameter will change based on material specifications. For all of the studied samples at worst condition, we got the results including: HPGR delta gap equal to zero, specific throughput lower than 200 ts/hm3.According to the tests results, HPGR Applicability Index (HAI) can be introduced at four different class types from 1 (weak) to 4 (excellent). This index determines achievable specific throughput and possibility of using HPGR according to material specifications, i.e. for HAI 1-4 the pressure resistance is <90, 90 to<125, 125 to <150 and = 150 bar, respectively. Similarly for HAI 1-4 specific throughput is <200, =200, =220 and =250, respectively. So based on design moisture content, if concentrate HAI is 3 or 4, HPGR is a correct choice. For HAI 2, HPGR can also be used. But for a material with HAI equal to 1, HPGR is not a good solution. As a result in order to apply HPGR for HAI 1, material condition such as moisture or slime content should be decreased.

Jan 1, 2018

By Shailin Lalloo, Allan B. Nesbitt

A fluidised bed was exposed to high gravities by placing it in a centrifuge. The bed expansions were measured and compared with the bed expansions predicted by the Richardson-Zaki model (1954). The Richardson-Zaki model was found to predict effectively the fluidisation behaviour of defined particles in this increased gravity environment.

Jan 1, 2003

By Gerke Gilian, Pretz Thomas, Pehlken Alexandra

"The evaluation of health hazards within the treatment of mineral and waste materials is gaining more and more importance in industrial countries. The need to control occupational health and safety has been recognised, and regulations which describe general protective measurements for personnel provide a tool to protect their health. It is the aim of the paper to give an outlook for practical approaches to risk assessment and to present measures for exposure reduction in accordance with the state of the art in Germany.Both the treatment of minerals and of waste materials are described in relation to the risk assessment. The method of evaluating health hazards in the two industries is similar and therefore both examples are presented next to each other.The example presented in the paper is the German “Biostoffverordnung” (the regulation for biological materials) which is important for the waste treatment industry. All kinds of waste treatment facilities (like composting facilities, waste dumps, sorting facilities for packaging materials) are obliged to carry out an assessment of health hazards for a variety of working areas and working places. The possible safety requirements deriving from this regulation are presented and discussed under the aspect of biological hazards."

Jan 1, 2003

By R. Shiva Kumar, G. E. Sreedhar, Rajan Kumar, K. Suresh, A. K. Aketi Veera, M. Narasimha, P. S. Jodan

"In most of the coal washeries, Dense Medium Cyclone’s (DMC) are deployed to treat coarse coal fraction in the range of 50-0.5 mm. DMC’s are very popular due to its ability of high tonnage, ease of operation and effective separation at high near-gravity material (NGM) in feed coal. The ease or difficulty of washing is merely depending on the NGM fraction present in run of mine coal. However, the quantitative effect of NGM on DMC performance was not explored in the literature. Hence, in this investigation, the influence of NGM on DMC performance is focused. With the help of synthetically prepared coal mixture, the effect of NGM mass fraction on separation efficiency is studied in three different approaches. Firstly, by increasing the NGM coal fraction systematically from low to as high as possible; second by varying the distribution of NGM coal; and third by varying distribution of particles lying just above and below the near-gravity zone. Washability studies are also carried out to establish the theoretical yield for the prepared synthetic mixtures. Pilot-plant experiments are carried out in a 4-inch DMC with 1.4 operating separation density treating coal in the size range of 4 - 0.5 mm. From results, the partition curves are constructed by both density and size wise distributions. It is observed that at higher NGM coal fraction i.e above 60%, the performance of DMC is very poor with significant coal particles misplacement. In second approach with increased distribution at higher density fractions, the separation efficiency reduces. In third series the distribution of fraction in near-gravity zone doesn’t much effect the separation except the shift in separation density. It is observed that smaller size (-0.5 mm) coal particle having high NGM content seems have a profound effect on DMC performance leading to significant fines misplacement to wrong products."

Jan 1, 2018

By A. A. Lavrinenko, N. I. Gluhova, L. M. Sarkisova, D. V. Makarov

"The purpose of the study is to study the feasibility of using sodium diisobutyl dithiophosphinate (DDP) to enhance the recovery of platinum group elements from low-grade refractory copper-nickel ores characterized by a portion of nickel and platinum group elements (PGEs) locked in the dominant sulfide mineral — pyrrhotite. These ore characteristics dictate the need to produce a bulk PGE-containing sulfide concentrate due to the difficulties of producing selective concentrates without a significant loss of the metals.New data on the adsorption and flotation performance of DDP-containing collectors were obtained by measuring the electrode potential, hydrophobicity of the sulfide mineral surfaces and by means of extraction spectrophotometry and flotation studies. The interaction between DDP, pyrrhotite, and pentlandite leads to the formation of surface hydrophobic layers consisting mainly of disulfide and a small amount of metal compounds. These adsorption layers are formed by the reaction with butyl xanthate. In the case of cooperite, DDP reacts with the surface, forming not only disulfide, as in the case of butyl xanthate, but also a complex platinum compound. DDP-containing agents demonstrate stronger collecting properties with respect to sulfide minerals of copper-nickel ores compared to butyl xanthate, which is explained by a stronger hydrophobizing effect and foaming properties.The addition of a combination of DDP-containing agents and butyl xanthate at a ratio of 3:1 for the recovery of sulfides and PGEs in the bulk flotation of copper-nickel ore made it possible to improve the recovery of Ni, Pt, and Pd by 13.6, 9.2, and 9.4%, respectively, relative to the recovery achieved in flotation with butyl xanthate.Bulk flotation with the addition of a composition of DDP-containing agents and butyl xanthate allows the most complete recovery of all valuable elements and is the only technologically feasible method for processing of lowgrade ores, when it is impossible to produce without loss high-grade selective concentrates suitable for smelting."

Jan 1, 2018

Certainly, one of the core processes for the recovery of fine magnetic susceptible iron ore particles, mainly hematite iron ores, is the wet high intensity magnetic separation or WHIMS. This paper outlines a variety of recent developments and innovative process designs in the JONES® type WHIMS. It highlights the latest examples of flow sheets in terms of the diversity of combined rougher, scavenger, cleaner stages and adds to this the new more advanced JONES® type WHIMS equipment technologies like the HIGH FLOW ? HF, the QUATTRO ? Q and the SPLITT OPERATION ? SP. As a result of the increase of the capacity and magnetic intensity, the specific production cost could be decreased. The high worldwide acceptance for this continuous development testifies for the success and state of the art technology.

Sep 1, 2012

By F. C. Yi

Discontinuous and consecutive process was applied to probe into the Kinetics and adsorption theory for Cs+ adsorbed by Zeolites under the conditions of temperature, time and fixed-bed dynamic adsorption. It indicated that the sorption kinetics behavior of zeolite?s sorption on Cs+ is ac-cord with pseudo-secondary velocity equation, velocity constant k2=0.0005213 g?mg min-1, and equilibrium adsorptive capacity is 147.0588 mg?g-1; The equation can be expressed as: Y=0.0068X+0.0887; From the analyzing of diffusion coefficients on different temperatures and times, the coefficient of diffusion is not only related with the fabric of mineral and the character of ions but also the temperature and time; When the ambient temperature hoisted, the diffusion velocity augmented rapidly; Cs+ would get over a certain energy barrier when it enters into structure of zeo-lite; This energy is expressed by activation energy, and its value is E=131.668818 kJ?mol-1; There are two dominating adsorption mechanisms in the system of zeolite absorb Cs+: ionic interchange and surface coordinate adsorption.

Jan 1, 2014

By Avishan Atrafi, Marek Pawlik

"Gas dispersion properties of sodium salts of 6, 12 and 18-carbon fatty acids (hexanoic, lauric and oleic acid) were investigated as a function of pH. A strong effect of pH was observed on gas dispersion properties of fatty acids. At high pH for 12 and 18 carbon fatty acids, at which these surfactants formed a true solution, the gas dispersion properties were similar to those of MIBC. In the case of sodium hexanoate, which has a much higher solubility than the longer chain fatty acids and therefore does not form precipitates, the gas dispersion properties of this surfactant were strongly enhanced in the acidic pH range, where hexanoic acid was fully associated. This result is an indication that undissociated hexanoic acid is much more surface-active than anionic hexanoate. Only a small effect of the surfactant chain length on gas dispersion properties of the tested reagents was observed. The measured critical coalescence concentration (CCC95) values increase slightly by decreasing chain length and range from 5.8 x 10-5 mol/L (17.7 mg/L) for sodium oleate to 7.2 x 10-5 mol/L (16 mg/L) for sodium laurate at pH 10 and 1.9 x 10-4 mol/L (26 mg/L) for sodium hexanoate at pH 3.7. These are compared to CCC95 of MIBC, which is measured to be 8 x 10-5 mol/L (8 mg/L). The soluble molecular species were recognized as the most effective species in preventing bubble coalescence."

Jan 1, 2014

By Long Han, Jianyuan Liu, Ping Ying

"Particle-bed compressive stressing is the main work mechanism of comminution by high pressure grinding rolls(HPGR). An experimental study on comminution and mineral liberation of two copper sulfide ores was carried out using a piston-die compressive stressing rig to simulate the situation of comminution with HPGR as the final-grinding device. The tests carried out include compressive comminution tests on particle-bed with narrow-size feed, and the locked-cycle comminution test on particle-bed with broad-size feed, which was then compared to a corresponding locked-cycle test of ball-mill grinding. The narrow-size feed is made up of particles in the size range 2.36~3.35 mm, whereas the broad-size feed of particles in the size range 0~3.35 mm. The liberation analysis for copper-mineral in the comminution products was accomplished using BPMA system – an automatic mineral liberation analyzer developed by BGRIMM. The influences of the stressing intensity and the method of comminution on the copper mineral liberation are discussed in terms of product size distribution, copper-metal deportation among size fractions, distribution of copper mineral among particle-size and particle-grade classes, degree of mineral liberation in size class as well as degree of mineral liberation overall.INTRODUCTION Traditionally, comminution process commonly applied in mineral processing is a flowsheet consisting of crushing of crude ore with conventional crushers, followed by grinding of the crushed ore in tumbling mills. In last decades, the energy-efficient HPGR (high-pressure grinding rolls) has found its application in mineral processing, mostly as tertiary or quaternary crusher to generate a fine-crushed product either as feed to subsequent grinding or as feed to a pre-beneficiation process before further grinding. Compared with the process of conventional crushing followed by grinding in ball mill, this mode of HPGR-application can achieve energy saving to some extent by reducing particle size of the feed to ball milling, and by reducing amount of the feed to ball milling if a significant portion of tailings in relatively coarse particle-size range can be discarded at the pre-beneficiation stage. In recent years, the approaches of letting HPGR take more comminution work from ball mill by applying it in semi-finish grinding mode or even finish grinding mode have been discussed (Burchardt, 2014). Although HPGR finish-grinding has been successfully applied in the cement industry for grinding of cement clinker and raw materials, this mode of HPGR application has yet rarely been implemented in mineral processing, despite the advantage of more energy-saving and other potential benefits such as preferential breakage, internal damage of particles and enhanced mineral liberation which may lead to a better downstream processing performance. The reasons for the retardation of the progress of this kind of HPGR-application in the mineral industry lies not only in that a finish-grinding with HPGR has to be operated in dry condition whereas most of ore-beneficiation processes like flotation are operated in wet condition, but also in that there are large variety of ore materials with various complexity of processing technology, which need to be addressed on a case-by-case basis with a lot of test work, in order to evaluate the potential advantages or disadvantages of this application."

Jan 1, 2018

By E. Lee

With the growing environmental concern, as well as the increasing concern for sustainability of natural resources, the need of improving the performance and efficiency of today?s crushers is be-coming increasingly important. However, the development of existing crushers requires an extended basic knowledge about the crushing process itself. The aim of the present study is therefore to find the theoretically optimal way of crushing compressively under given circumstances. In the present paper, optimizations have been performed with the purposes of maximizing product yield and minimizing energy consumption. Performed on an ideal crushing stage free from physical limitations, the optimization results have been obtained in terms of number of compressions and their corresponding compression ratios. Complementing earlier results on interparticle breakage (Hulthén et al., 2006), presented here are thus the results from corresponding optimizations with single particle breakage and interparticle breakage. It is concluded that modern crushers are not working optimally in any of the studied aspects for gneiss. In fact, optimizations indicate that a lowering of the compression ratio, as well as a shortening of the crushing sequence, are theoretically favourable. The outcome of this study is therefore highly promising as to giving new ideas and suggestions of improvements in existing crushers, and can even result in redesign of compression crushers.

Jan 1, 2014

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018