Search Documents

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018

By Osvaldo A. Bascur

One of the most vigorous of the continuous improvement methodologies is Six Sigma. While usually associated with improving manufacturing and product quality, leading manufacturers are using it to improve their extended supply chain and logistics capabilities. At the same time they are improving reliability, some companies have cut hundreds of millions of dollars of fat out of their supply chain. Mine to Mill optimization is a transformation of culture from processing tons to processing a quality feed size distribution which reduces the overall operational costs and add the highest value to the mine. This is not a constant endeavor. As such, a dynamic performance monitoring and diagnosis is necessary. We will review a systemic way to performance improvements and avoiding metal losses from the blast to the metals. We show the requirements of using raw data to analysis the data to define operational maps which provide assistance to run the mine and mill. A case study is provided with the mine and mill data was integrated combining process control and quality information resulting in reduction of water and energy consumption while improving the overall value of the mine. The results of reengineering the current system with this SIX SIGMA Strategy had the following results: an increase of ore milling: 4.6% decrease of mil power: 3.9%, decrease of fresh water consumption: 6.8%, with a total of net profits: US$ 31.8 million, the PI System infrastructure contribution: US$ 7.95 million. These estimates were for the period 2009/04/04 to 2009/12/31.

Sep 1, 2012

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Grinding is one of the most energy consuming unit operations and is also a very inefficient and costly process. Therefore, it is of great importance to run the grinding process as efficiently as possible. The most common way today to control grinding processes is by measuring the power draw of the mill and try to keep it at a maximum level. However, some studies (Kawatra, 1989, Koivistoinen, 1989, Moys, 1989) have shown that this measurement doesn.t reflect everything that takes place inside a mill. Among other parameters like slurry rheology, temperature and charge behaviour, the volumetric filling of a grinding mill seems to have a large influence on the grinding efficiency (Herbst, 1988, Koivistoinen, 1992, Vermeulen, 1988). A problem in attempting to measure those parameters has been to get a sensor that is both robust and sensitive enough for continuous on-line measurement.This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a DEM modelling technique is used.The results indicate that the system is capable of following the normal variation that occurs in the mill. The signal also very well reflect changes in operating variables such as ball charge level, pulp density and rotational speed. By studying the nature and different features of the signal one can get a better understanding of milling circuit dynamics. Another feature of the technique is the possibility for an operator to continuously follow the grinding process and thereby run the process under optimal conditions."

Jan 1, 2003

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

By Cuim R., M. L. Li

Fankou Lead-Zinc Mine produced pyrite concentrate (P.C.) from the zinc tailings by rougher and scavenger flotation before 2010, with the averaged S grade of 40.54% at recovery of 79.34% ( to the feed of S circuit). On the one hand, the economic value of P.C. increases with its purity, on the other hand, when the S grade of P.C. feed to sulfuric acid manufacturer is over 47%, the pyrite cinder can reach a high Fe grade of 62% which can be directly sold as iron concentrate. On this background, engineers in Fankou Mine set the P.C. with S grade of 47% as target. The direct way to reach that goal was to clean the rougher P.C.. Lots of cleaning flotation tests were conducted and the compromised strategy was to produce two ranks P.C. with the S grade of 47% and 38% at the recovery of 44.20% and 36.17%, respectively. The dual-product flowsheet was successfully industrialized in 2010. In order to further improve the quality of P.C., gravity separation was introduced into the flowsheet. The numerical simulation and separation tests were performed to evaluate the beneficiation and classification performance of hydrocyclone as it treated the rougher P.C.. It was shown that the underflow of hydrocyclone could addressed the S grade of 47%, and the finer size overflow could also be enriched to P.C. with S grade of 47% by flotation, due to the contained pyrite with well liberation. That is to say, with the ingenious addition of hydrocyclone to treat the rough P.C., single P.C. with S grade of 47% could be achieved. The new flotation-gravity separation flowsheet was commissioned to produce the high quality P.C. at the end of 2013. The averaged S grade is 47.20% at recovery of 82.26% in 2014. The two steps flowsheet improvement maximizes the enterprise benefits and leads to simple utilization of Fe in pyrite in downstream industry.

Jan 1, 2018

By G. Sedelnikova

This paper is aimed to elucidate the problem of copper losses in pyrometallurgical slag. Currently, flotation is used to recover copper from the slag and return the metal into the pyrometallurgical process, but the percentage of recovery frequently remains unacceptable. The process of copper leaching from the slag flotation tailings using biologically regenerated ferric sulfate is considered here as an approach to the issue. A sample of the slag flotation tailings containing 0.67% Cu and 4.99% Zn was supplied by the Urals Mining and Metallurgical Company (UGMK, Russia). The Cu and Zn speciation analysis of the sample demonstrated that Cu occurred as 58.1% oxide, 15.4% native Cu, and 18.1% secondary sulfides whereas chalcopyrite proportion was as low as 8.4%. Prevailing Zn species were refractory (58.9% Zn ferrite), and zinc oxide and silicate species made just 37.2% of the total metal content. The silicate generated silica gel that strongly hampered filtration. As demonstrated, Cu recovery is a possibility, which is apparently not the case with Zn. In this work, the stirred tank bioreactor acid leaching employing bacterial Fe3+ sulfate solutions was studied, with ferric sulfate being a product of Fe2+ biological oxidation and not the chemical reactant adding of Fe3+ sulfate. Acidithiobacillus, Sulfobacillus, and Leptospirillum bacilli were employed in Fe2+ biooxidation. Temperature, pH, Eh, S:L ratio, leaching time, and Fe3+ concentration in the source leachate as the process controls were considered. As demonstrated, the process employing biologically regenerated ferric sulfate proved to be more efficient than conventional chemical leaching. Under the optimum conditions, the proportion of Cu extracted into leachate during 2 hours was 79.1%, and that of Zn 27.2%. Precipitation of high-grade Cu sulfide served to extract the metals from the leachate, and Cu extraction was 99.7%. All in all, 23.2% Cu, 0.03% Zn, and 0.02% Fe was returned into the pyrometallurgical process. Keywords: slag flotation tailings, copper leaching

Sep 1, 2012

By Andrew Logan

Newcrest has a strong history of growth over the past 20 years, yielding value from previously marginal ore bodies. We have grown regionally in Asia Pacific through our operations in Australia, Indonesia and Papua New Guinea, and also established a beachhead in West Africa. The company has a reputation of realizing value from large, low-grade deposits adopting step change approaches. Newcrest is focused on an overall strategy of gold, low cost, long life and moderate growth. Capability step changes play a large delivery role. They transition from a business offline-to-online approach as opportunities mature. Newcrest believes in a) Knowing what ?good? looks like, b) An open innovation approach to actively working with others, c) The leap frogging leverage of making the ?old new again?, d)An adopt-adapt-develop methodology enabled by rapid prototyping/piloting, e) Getting our handsdirty with test work and plant analysis, and f) Staying focused on a few high business leverage areas. This paper describes Newcrest?s approach and our experiences in establishing renewed metallurgical processes, specifically aimed at increasing innovation adoption. Some of our step changes discussed include: 1) Early waste rejection to avoid high energy processing downstream, 2) Broader gold product channels to reduce site based processing needs, 3) Lower energy processing, and 4) Geo-Metallurgy approaches. Keywords: Newcrest, gold, step change, open innovation, adopt, adapt, develop, offline, online, prototyping, old new again, waste rejection, low energy, geo-metallurgy

Sep 1, 2012

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U.S., burning approximately 860 million tons of coal annually. This results in the production of 58 million tons of fly-ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludge.s annually. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and by-products as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which makes them unsuitable for existing markets.Mineral processing techniques are useful for upgrading and utilizing combustion by-products. Fly-ash can be processed to remove unburned carbon, or utilized as a binder component in ore pelletization and agglomeration processes; bottom ash can be processed to produce certain aggregate grades; CO2 emissions can be sequestered using modified leaching techniques; and many scrubber sludge’s require processing before they can be used for producing gypsum products.The experiments described in this paper were carried out to study the application of mineral processing techniques to upgrading combustion by-products, particularly flue-gas scrubber sludge. A process was developed for upgrading unoxidized Flue-Gas Desulfurization (FGD) sludge’s by removing the primary impurity (unreacted limestone). A combination of hydrocycloning followed by froth flotation reduced the limestone concentration to as little as 1.7%, while recovering 66% of the sludge weight as a clean product. The recovered limestone was sufficiently concentrated that it could be recycled to the scrubber for more complete utilization."

Jan 1, 2003

By A. Ghadyani

This investigation was undertaken to assess the possibility of ash and sulfur removal by microbial action of high sulfur-content coal. Thiobacillus ferrooxidans and Thiobacillus thiooxidans have been used for biodesulfurization of coal. Feed samples were provided from Tabas coal mine located in Yazd province, Iran. The sample contained 28.80% ash and 2.30% sulfur. Flotation tests were implemented to optimize the effective parameters in these cells which were constant during bio-flotation tests. According to the results, obtained from various tests using Taguchi orthogonal array design (L27), the values of optimized parameters were pH at 7, 1000 g/t gas oil as a collector, 10% solid content, 15 min conditioning time, 100 g/t MIBC as a frother and 800 rev/min rotor speed. Bio-flotation tests are carried out by means of laboratory double discharge cell and mesophilic bacteria as depressant reagent using above mentioned optimized parameters. The bio-flotation experiments were conducted based on a Taguchi orthogonal array design (L9) with four variables (bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time). The collected data was analyzed by using DX7.0, Minitab14.0 and WinRobust1.02 softwares for evaluation the effect of each parameter on the optimization criteria. Considering the highest combustible recovery and the lowest ash and sulfur content, the value of optimized bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time were Thiobacillus ferrooxidans, 5×107 cells/g(coal), 100 rev/min and 20 min respectively. Under this condition, ash and sulfur content and combustible recovery were predicted 12.39%, 2.08% and 82.03% respectively.

Sep 1, 2012

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

"To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.INTRODUCTIONCopper is one of the first metals extracted and the main material of choice for different high-technology applications today. Currently 80% of the world's copper comes from copper sulfide ores. However, due to the depletion of high-grade copper ores in the world and constantly growing demand for copper, the need to develop processes and technologies to treat copper resources from additional sources such as mine tailings, low grade deposits, industrial wastes and deposits with high impurity levels such as As and Sb will continue to increase (Miller and Craig, 1983). The beneficiation processes of copper-pyrite ores consisting of tennantite-tetrahedrite series minerals are generally complex. Tetrahedrite-tennantite minerals occur as fine anhedral grains intermixed with grains of galena, sphalerite, chalcopyrite, pyrite and other sulfides (Saharova, 1966). The mineralized zones of Southern Urals, Russia deposits correspond with these ore types but tennantite-tetrahedrite series are more abundant in ores at the Uzelginskoye deposit, some samples of which contain 70% of copper in tennantite form (Seravkin et al., 1994). This deposit differs from other similar copper-pyrite ores by thin mutual ""germinating"" minerals and higher content of arsenic (up to 0.8-1 %) which create additional considerable problems in enrichment (Solozhenkin et al., 2016)."

Jan 1, 2018

By P. Romm

The German Kupferschiefer (copper shale) mining history reaches back over 800 years with its last active mines being shut down in 1990. Increasing metal demands and potential thread of future supply shortages led to the initiation of new exploration programs including feasibility studies for the Spremberg deposit as well as Federal Ministry of Education and Research (BMBF) funded research investigations of Kupferschiefer Waste Dump treatment in the Mansfelder region. This article describes the sensor based sorting results of coarse Kupferschiefer via Near Infrared (NIR) Sorting, being conducted by the department of mineral processing (AMR) in Aachen, Germany. It provides information about the necessity of presorting of the different ore types prior to flotation and puts the NIR Sorting results into context with conventional Kupferschiefer processing. Keywords: NIR sorting, kupferschiefer, sensor based sorting, preconcentration

Sep 1, 2012

Cyanide is reactive to copper minerals and is not suitable to extract the gold from the copper bearing ores. Ammoniacal thiosulfate is considered an excellent alternative lixiviant for leaching copper bearing gold ores. Unfortunately the results of high reagent consumption and poor gold ex-traction were found by thiosulfate leaching of synthetic gold ores containing chalcopyrite, chalcocite or bornite and a mild refractory copper-bearing sulfidic gold ore. In this investigation, several processes have been applied to reduce the impacts of these minerals on gold leaching. The process included: the pre-oxidation of copper sulphide minerals in water or ammonia solution, the reduction of dissolved oxygen in the lixiviant (0.3 ppm DO or 0.7% oxygen), adding phosphate anion in the leach or pre-leach stage, and the addition of a strong copper ligand (e.g., EDA and DETA). The results indicated that the gold extraction could be improved to 93% with the thiosulfate consumption being reduced to less than 8 kg/t. The dissolution of copper minerals was found to be the major reason for increased consumption of thiosulfate and the highly reductive leached surfaces are responsible for the reduced gold extractions.

Jan 1, 2014

By D. Saramak

The proposal of the nip zone angle determination in HPGR crushing process is presented in the paper. Knowledge of the nip zone angle value, in turn, makes it possible to determine the real maximum pressing force in the high-pressure comminution. Two methods of determination of this maximum pressure were proposed and verified. The first method is based on the roll?s geometry, and the change of the HPGR chamber?s volume together with the roll rotation, while the second one considers the outlet gap width impact. Results of the nip zone angle calculations according to both methods are similar and show convergence with the real operating conditions. The verification was carried out in a piston-die press, and experimental results show that methodology of the nip zone angle determination presented in the paper has its practical confirmation. A proper determination of the nip zone border makes it possible to calculate the comminution probability of given type of material and is a basis for the HPGR crushing process modeling and optimization. Keywords: HPGR, comminution, nip zone, ore processing

Sep 1, 2012

By S. Liu

With the development of global economy, the demand of mineral?s quantity and quality are in-creased, valuable minerals are more and more finer and poorer, and the capacity of concentration plant are more and more high. Using large-scale flotation cells can obviously enhance the capacity of treating the mineral, reduce the cost, and increase the economic benefit and competitive ability for the enterprise. BGRIMM advanced advisable technical scheme with optimally parameter and route for the feature of dynamic in large scale flotation machine, and developed the KYF Large Scale Flotation Cells, which have used more than 400. The paper advanced the history, the design principle, the operating principle, the structure feature and the application of KYF flotation ma-chine.

Jan 1, 2014

By A. M. Ozbayoglu

Gross calorific value (GCV) of coals was estimated using artificial neural networks, linear and non-linear regression techniques. Proximate and ultimate analysis results were collected for 187 different coal samples. Different input data sets were compared, such as both proximate and ultimate analysis data, and only proximate analysis data and only ultimate analysis data. It was observed that the best results were obtained when both proximate analysis and ultimate analysis results were used for estimating the gross calorific value. When the performance of artificial neural networks and regression analysis techniques were compared, it was observed that both artificial neural networks and regression techniques were promisingly accurate in estimating gross calorific values. In general, most of the models estimated the gross calorific value within ±3% of the expected value.

Sep 1, 2012

By V. A. Chanturiya

There is an obvious disproportion in Russia gold-mining industry between the structure of gold reserves and the gold-mining techniques. The bulk of gold (over 70%) is extracted from alluvial deposit, 20%~25% from bedrock occurrences and 5%~7% from complex copper-zinc and polymetallic ores. The proved gold-bearing reserves are distributed as follows: alluvial ?19%, bedrock ?80%, the latter being sufficient to supply gold at the current production level for 100 years to come. In Russia, like elsewhere in the world, development of primary gold deposits is considered a first-priority line of development for gold-mining industry. Most of the gold-containing ores characteristic of Russian gold deposits are resistant ores with gold content varying between 3 ppm and 5 ppm usually showing quite low gold and silver recovery by cyanidation. Processing resistance of gold-containing mineral complexes is related to the presence of gold particles of submicrometric (<1.0 µm) and nanometric (10~100 nm) size, mostly asso-ciated with pyrite and arsenopyrite. Therefore switching over to processing bedrock entails a num-ber of technological problems that stem from chemical and physical resistivity of ores. The chemical resistivity can be overcome through flotation, oxidation roasting, autoclave leaching (biohydro-metallurgical oxidation), etc. The physical resistivity can be dealt with by resorting to traditional power-intensive methods,e.g. grinding to a ?40µm size, thermal treatments of sulphide concentrates and non-traditional high-energy methods of liberating the sulphides by means of power attack, e.g. electro-chemical oxidation, exposure to electron beam radiation and other methods. The modern non-traditional processes for treatment of rebellious noble metal-bearing ore, aimed at improving disintegration efficiency for finely dispersed mineral complexes are analysed. Advantages and perspectives of a new high-efficient, energy-saving and ecologically safe process of the nanosecond high-power electromagnetic pulses (HPEMP) effect are proved. The said process provides a stable increase in the valuable component recovery at lower energy consumption and production costs of the finite product at the stage of dressing rebellious gold-bearing ores and concentrated products. The experimental data prove high efficiency of the preliminary impulse treatment, thus, the increase in the gold recovery at the cyanidation stage amounted to 4%~12% from rebel-lious ores, 10%~30% from gravity concentrates, 5%~45% from flotation concentrates, 30%~80% from oil flotation tailings.

Jan 1, 2014

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By Z. S. Abisheva

Rare and rare earth metals use quite often is an indicator of national economy development. The world structure of the rare-earth metals manufacturing countries in 2015 was presented as follows: China – 94.2%, India – 2.0%, Russia – 1.8%, the USA – 1.2%, Brazil – 0.5%, Malaysia – 0.3%. In Russia, large reserves of rare-earth metals, which reach nearly 28 million tons, are revealed. Kazakhstan, possessing a raw materials source of rare-earth metals, has all prerequisites for development of branch. Rare metals are manufactured in Kazakhstan incidentally by non-ferrous metals production. The production of indium, thallium, cadmium, selenium, tellurium, bismuth is made at the Ust-Kamenogorsk lead plant; tantalum, beryllium, niobium and molybdenum – at the enterprises of “National Atomic Company Kazatomprom” JSC. Production of a titanium, magnesium and vanadium is adjusted on “Ust-Kamenogorsk Titanium-magnesium Plant” JSC. Capacities for beryllic production yield are available on “Ulba Metallurgical Plant” JSC. The main producer of perrhenic production and osmium-187 is "Zhezkazganredmet" RSE. The single producer of gallium in Kazakhstan is “Aluminium of Kazakhstan” JSC; the capacity of enterprise is 25 t a year. In Kazakhstan innovative technologies for rare and rare earths mineral raw materials processing are created. The technology has been developed and a vacuum distillation apparatus has been created to purify crude selenium, which makes it possible to obtain a metal with a main component content of 99.9-99.99%. Technologies for processing of technogenic wastes and byproducts of the copper industry are developed. Implementation of technologies allow to obtain ammonium perrhenate, perrhenic acid, osmium isotope -187, tribasic lead sulphate, silver-concentrate. The technology of complex processing of black shales of Balasauskandyk deposit with the production of gold, vanadium, rare earth elements, uranium and ferrosilicon has been proposed. The processing was carried out using methods of autoclave leaching, sorption, extraction, precipitation. A highly profitable sorption technology for recovery of rhenium from solutions of underground leaching of uranium ores containing 0.2-0.4 mg/L of Re has been created. The organization of ammonium perrhenate production from solutions of uranium ore will significantly increase the volume of its production in Kazakhstan.

Jan 1, 2018