Search Documents

By Markus Dammers, Christopher Robben, Hermann Wotruba, Christian Schropp

"In most underground mining processes the entire extracted ore is transported from underground workings to surface processing plants for separation of valuable minerals and gangue material. Most of the transported material consists of barren rock with negligible metal content, especially for low grade deposits, such as in the copper or gold metal ore mining. Increasing mining depths result in higher costs for transportation and hoisting. Therefore, rejecting waste rock as soon as possible from the material stream gains importance. The concept of resource to product integration in the form of earliest waste rejection in combination with subsequent backfilling follows the philosophy of ‚leaving waste underground?. Implementing mineral processing underground can lead to less required mass movement to surface, hence reducing transportation and hoisting costs. At the same time, rejected waste can be used as backfill to increase extraction rates by reducing pillar volumes. In the mill, a stable high grade feed leads to decreased specific operating and investment costs as well as increased productivity and recovery. These effects as a whole have a large potential to reduce cut-off grades so that resources can be turned into reserves. Within the I²Mine (Innovative Technologies and Concepts for the Intelligent Deep Mine of the Future) project of the European FP7, investigations are carried out by the Unit of Mineral Processing of RWTH Aachen University, the Institute of Mining Engineering I and TOMRA Sorting Solutions | Mining. One aim of the cooperation is to develop new concepts for a comprehensive integration of near-to-face processing in combination with backfill into the overall underground mining process. Effects on up-, down- and side-streams are investigated to prove the potential of resource to product integration in comparison to common underground mining systems and processing methods."

Jan 1, 2014

By Andrzej Luszczkiewicz, Magdalena Duchnowska, Jan Drzymala

A selected flotation system of beneficiation of the copper ore at KGHM Polska Miedz S.A. has been analyzed in the article. It was found that a proper assessment of upgrading must be based on two elements, that is the upgrading process selectivity and working point of the considered flotation unit, both determined, preferentially by means of the Fuerstenau recovery-recovery upgrading curve. The Cu recovery - non-Cu components recovery upgrading curve was selected for calculations because its background lines (no separation and ideal separation) are insensitive to changes in the grade of feed of the processed material. This approach allows a comparison of upgrading results for feeds having different grade, being upgraded in various flotation machines and under different physicochemical conditions. It was shown in the paper that the main criterion for comparison of two working in parallel systems is selectivity of upgrading. However, when two flotation machines, despite of the same selectivity, produce concentrate and tailing of different grades, it is necessary to analyze their working points using upgrading curves. The proper position of the working point depends on the criterion imposed on the process and is a result of not only basic parameters of the upgrading process such as feed, concentrate and tailing grades but also on economic parameters such as costs associated with the production of concentrates and the time needed for their production.

Jan 1, 2014

By Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"The process of grinding in drum mills is directly dependent on the dynamic forces occuring in the free movement of the grinding bodies in the volume. The subject of discussion are the potential impacts between grinding bodies having different shape and equal weight in a drum mill that has a diameter of 1200 mm. The study utilised ball grinding bodies having a diameter of 120 mm and tetraballpebs having a conditional diameter of 120 mm. The study was carried out using the Solid Works Simulation software. The following cases were examined: • Impact between two identical grinding bodies; • Impact between a grinding body and the shell surface. The study provided numerical values for impact force, kinetic energy of impact, linear speed of impact, linear displacment of the center of gravity and duration of impact deformation. The impact force of the balls is approximately 179000 N. The impact force of the tetraballpebs with typical vertices, edges and spherical surfaces depending on the area of impact is 177000 to 185000 N. Upon impact between two spherical surfaces of tetraballpebs, the contact area is 263.55 mm2, which is more than twice the contact area upon impact between two balls, which is 114.39 mm2. This determines better conditions for the transmission of kinetic energy by reducing opportunities for overgrinding."

Jan 1, 2014

By Andrzej Luszczkiewicz, Tomasz Chmielewski, Jan Drzymala, Andrzej Konieczny, Rafal Kaleta

Properties of the sedimentary Polish copper ore mined from the Legnica-Glogow Copper Basin (SW Poland) by KGHM Polish Copper S.A. were presented and currently used beneficiation technologies were described. Due to a unique lithological layered structure of the polymetallic deposit and existing mining system, the ore currently processed in the three KGHM concentrators is very complex with variable content of the carbonate, sandstone and shale fractions. The mined copper ore contains from 0.8 to 1.8 % Cu and Ag, Pb, Zn, Ni, Co, V and Mo as accompanying metals. The paper presents difficulties in upgrading the LGOM ore and selected possible solutions and development concepts of its processing. The first one is a chemical treatment with controlled amount of sulfuric acid of special product of flotation such as for instance middlings. The acid treatment leads to increased liberation of copper minerals and better further processing. Another concept is atmospheric leaching in oxygenated sulfuric acid and ferric ions solution as the major unit operation applied to selected low grade final flotation concentrates or flotation by-products. The third approach, based on copper ore pre-flotation with a frother to partially remove Corg, is also considered.

Jan 1, 2014

By Muammer Kaya, Sait Kursunoglu

"Energy is the major concern for society. It is expected that developing country economies and populations will grow and consume more energy. Interest in nuclear power is rising, while the world looks for non-depletable energy source that will not contribute to global warming. However, it still has concerns of nuclear proliferation, radioactive waste and safety. It is necessary to overcome these concerns if nuclear energy is expanded to developing countries. Thorium (Th) utilization as nuclear fuel will be an opening key of these difficulties because Th produces less Plutonium (Pu) and less radioactive waste with enhanced safety. Research into the use of Th as a nuclear fuel has been taking place over forty years, through with much less intensity than that for uranium (U) or U-Pu fuels. Nuclear industry is currently using only 0.7% of the available energy from mined U. With huge resources of Th and relatively little U, Turkey has made utilization of Th for large-scale energy production a major goal in its nuclear power programme. Thorium fuel is plentiful and inexpensive. Energy is major concern for developing Turkish society. Turkey, today exports more than 70% of its energy as fossil fuels. In the last 50 years, Turks are skeptical, anxious and indecisive about having nuclear energy for electricity production. In the last 10 years, Thorium is brought into Turkish government’s attention and national discussion as a new, safe, clean, affordable, CO2-free, alternative, strategic and domestic nuclear energy fuel. Turkey recently contacted four VVER-1200 type Russian Nuclear Power Reactors using U as a fuel in Akkuyu (Rosatom) and another four units will be established in Sinop in the next decade by Japan (Mitsubishi-Westinghouse). Turkish nuclear programme must envisage use of domestic Th as a fertile material. This paper briefly reviews the developments of Th-fuel cycle for nuclear energy from global and Turkish perspectives. Previous Th reserve development and recovery studies from Turkish bastnasite ore are summarized in this paper."

Jan 1, 2014

By Wu Tao, Lu Shijie, Xia Xiaoou, Zhang Ming

The impeller and stator are the most important components that can significantly influence the performance of flotation cells directly. The performance of the impeller and stator of KYF flotation cell is revealed by CFD (Computational Fluid Dynamic) simulation in this paper. A method of obtaining the circulation volume is proposed. The circulation volume is proportional to third power of impeller diameter. And the circulation volume increases linearly with the increasing of the speed. CFD simulation can draw the conclusions that there is a proportional relationship between power consumption, third power of speed and fifth power of impeller diameter. CFD prediction results agree with the theoretical formula. The difference between the forward and backward impeller is analysed in the paper. The circulation volume of the backward impeller is obviously larger than that of the forward impeller under the same condition, but power consumption of the backward impeller is lower. It is demonstrated that the impeller and stator system of KYF flotation cell is an efficient and reasonable stirring mechanism. CFD simulation could be reliably used in flotation cell design and optimization.

Jan 1, 2014

By G. Merazchiev

In the selection of copper ? molybdenum concentrates with the use of reagents containing sulfide ion ? sodium sulfide, sodium hydrosulfide etc for depression of copper minerals and pyrites, big part of depressor is oxidized by oxygen, which is dissolving in pulp during aeration with air in flotation machines and it is expended unproductively. This is the main reason for the big expenditures of depressor, reaching up 15~20 kg/t collective concentrate and the high exploitation expenditures for the copper ? molybdenum selection. Effective direction for lowering expenditure of depressor and increasing of the technical ? economical effectiveness of moly production is the conducting of the selection in nitrogen medium. In the paper are shown the results, obtained by applying of this direction in selection of collective copper ? molybdenum concentrate from the porphyry copper deposit ?Ellatzite? ? Bulgaria, in which the ratio Mo:Cu is over 1:120. In laboratory conditions, through comparative experiments in medium of air and nitrogen are defined: expenditure and initial concentration of NaHS in pulp for effective depression of copper minerals and pyrites; kinetics of flotation process of molybdenite; influence of pulp density; emf (negative milivolts) of pulp and the expenditure of nitrogen on tech-nological indexes of molybdenum flotation. When working in nitrogen medium decrease of NaHS in rougher molybdenum flotation from 40% to 45% is settled. When nitrogen is also fed in cleaner stages, the total expenditure of depressor is lowered by 64%. The quality of end molybdenum con-centrate is raised with over 5%. On the ground of the results of laboratory studies and of world practice data, an industrial installation for selection of copper ? molybdenum concentrate in nitrogen medium in Wemco inert ? gas machines.

Jan 1, 2014

By Christopher Greet, Alfred Van den Bosch

"A range of media alloys with different chromium content has been developed for different milling applications. When selecting the grinding media alloy for a specific application, consideration must be given to the mineralogy of the ore as well as the water chemistry and mill operating conditions. The paper describes the influence of the microstructure of the alloy on the wear resistance and the influence of the chrome content on the pulp chemistry and downstream processing. It also provides information about the in-house tools which Magotteaux have developed to predict the media wear rate with different chromium content alloys and predict their flotation efficiencies that can be expected when the right alloy is selected for a particular application."

Jan 1, 2014

By Bert Huls

Already starting, new drivers will dictate how future mineral processing plants will be designed and operated. These drivers include requirements in water and energy conservation because of rising costs, larger demand for mineral and metal products as the result of a rising population, and the increasing demand from the population in general to have influence over what type of operations will be developed where. Mineral operating facilities will require processing of lower grades. To do this economically, design engineers will be influenced to introduce newer concepts, or return to older processing concepts once deemed not desirable. Our understanding of the fundamentals must be improved, and this may come from better measurement techniques and more process piloting, and will go in hand with a reduction of waste generated during the process, improved separation of minerals or product size. Process engineers will also be required to not just design according to the established 3D methodology for efficient plant installation. Already in other industries the design concept encompasses the entire range from source to product. Not only that, the design will be affected by public influence that must be illustrated prior to project execution. On the one hand, the added dimension in design may slow a project; on the other hand it may result in a blessing, and in a higher responsibility for engineering.

Jan 1, 2014

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By Joseph Kelly, Christopher Kelsey

This revolutionary super-fine crusher has the unique capacity to generate fine and ultra-fine products from single stage reductions of coarse or fine mineral feeds. The crusher consists of a rotating compression chamber and an internal gyrating mandrel. The axis of rotation of the shell is displaced relative to the axis of the vertically mounted mandrel. The inner surface of the compression chamber is machined as double cone frustums at an angle equal to the displacement angle. Crusher feed is accelerated into a compacted particle bed, which lines the inside of the compression chamber. The depth of the compacted bed progressively increases until the mandrel is engaged. The mandrel is then free to rotate with the compression chamber. Continued feeding increases power draw and triggers the counter rotating mandrel gyration drive. The gyrating mandrel delivers multiple compressions at high pressure to the rotating particle bed. High concentrations of energy are harnessed within a small active volume over short retention times. The combination of extraordinarily high power intensity and extreme compressive force results in primary compressive fracture and induced secondary tensile failure. The axially displaced rotation of the compression chamber effectively distributes the breakage forces throughout the particle bed. This paper covers open circuit, pilot trials on magnetite, perlite, garnet, marble and a copper/pyrite concentrate. Particular emphasis is placed on the extraordinary results achieved with trials on zircon and highly refractory fly ash. The extreme duties were deliberately chosen to demonstrate the crusher’s application scope and potential to impact capital operating and maintenance costs as the technology matures. Super-fine crushing, once considered impracticable has the potential to offer compelling options for the generation of ultra-fine products.

Jan 1, 2014

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By M. Ranjbar, M. Khosravi Rad, A. Tohry

"The filling degree is defined as the volume ratio of the load inside the mill, which determines the power drawn from the motor, as long as the filling degree is not more than the optimum level. As the filling degree increases beyond the optimum level, the impact energy inside the mill will decrease and as a consequent, the mill power output will also decrease. Therefore, the mill filling degree is a key parameter in evaluating the grinding circuit performance, as it determines the mill reaction to the input feed. Since this parameter has an impact on the mill capacity, measuring the mill load is vital for control and optimization of grinding process. As in Choghart Processing Plant no instrument is available to measure the AG mill filling degree, an empirical model based on the bearing-oil pressure is proposed. The AG mill filling degree was related to the differences between the average pressure of input and output bearings, the circulating load and power drawn. It was shown that a quadratic model could relate the mill filling to the above mentioned measurements. This model showed that when the power drawn and circulating load decreases the bearing-oil pressure needs to be checked. If the bearing-oil pressure increases the feed rate needs to be decreased and steel ball be charged to the mill to increase the grinding and prevent mill overloading. INTRODUCTION The feed quality (size and hardness) affects the grinding process in AG mills. Reducing the top feed size and increasing the ore hardness reduce the mill efficiency and increase the particles with critical dimensions inside the mill. These will result in increasing the mill filling degree and reducing the mill throughput and efficiency (Wills and Finch, 2015). The volume ratio of the load inside the mill is called filling degree, which determines the mill power drawn. It is believed that if more energy is mainly spent on grinding (Wills and Finch, 2015). Therefore the mill power draw is used as a mean to control the mill efficiency."

Jan 1, 2018

By Michael Young, Rodrigo Araya, Cesar Gomez, Le Huynh, James Finch

The performance of flotation machines is closely related to the gas dispersion characteristics achieved in their operation. It is known that frothers play a major role not only in the size distribution of the generated bubble population, but also on the swarm rise velocity. A program to characterize frother effects on two-phase hydrodynamics (air-water) of Jameson cells was undertaken in a fully instrumented pilot unit installed at McGill University. Gas dispersion parameters (gas velocity, gas holdup and bubble size distributions) of the gas-liquid mixture generated in the downcomer were measured after its release into the separation chamber. The unit was operated under different conditions including gas velocity, liquid jet velocity and frother concentration (MIBC). Bubble size distributions for concentrations above the critical coalescence concentration (CCC) were narrow with Sauter mean diameter between 0.6 to 1.3 mm. The bubble size followed the general trend as encountered in other types of flotation machines, i.e., rapid decrease with increasing frother concentrations below 10 µL/L, and almost no change in size for concentrations above 30 µL/L. The CCC was between 10 and 15 µL/L. Strong correlations were found between bubble size and air-to-liquid flow ratio (APR), and between the bulk density of the aerated solution in the separation tank and the vacuum inside the downcomer. An equation is proposed to estimate gas holdup in the separation tank from vacuum and bulk density readings.

Jan 1, 2014

By Seungwoo Park, Gaurav Soni, Roe-Hoan Yoon, Hyunsun Do, Kaiwu Huang

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing bubble size to increase, bubble surface area to decrease, and hence casing less hydrophobic particles to drop off to the pulp phase below. Thus, bubble coarsening provides an important mechanism by which product grades are increased. On the other hand, excessive bubble coarsening results in low recoveries. In the present work, a model describing the process of bubbles becoming coarser in a foam as they rise to the top by deriving a mathematical relation between the Plateau border area, which controls film drainage rate, and the lamella film thickness, which controls bubble-coalescence rate. The model has been derived by assuming that liquid drainage rate increases due to slip at the air/water interface, and that the critical rupture thickness is determined by the capillary waves created by thermal motion. The model developed in the present work can predict the bubble size ratio between the top and bottom of a foam as functions of aeration rate, foam height, and surface tension (frother dosage). The model predictions are in good agreement with the changes in bubble sizes measured using a high-speed camera.

Jan 1, 2014

By M. Pischtschan, S. Belz, M. Perrucci

In High Pressure Grinding Rolls (HPGR), the material grinding takes place between the fixed and floating rollers. In this regard, the rollers start to wear over a period of time, which is impacted by for e.g.: ore characteristics, operating pressure, feed material size and non-uniform feed presentation across the roller width. HPGR operational experiences have shown that the rollers do not wear at the same rate. This differential wear rate over time leads to differences in the tangential speeds of the rollers, causing an uneven gap between the fixed and floating rollers in relation to the material. This unwanted but extremely common situation results in a less effective grinding process due to the fact that the slip between rollers is not optimal. As the rollers wear profile increases, the roller with smaller diameter starts to wear further, deteriorating the comminution efficiency up to a point where operators have to stop the HPGR to replace the rollers. Since the wear rate of the rollers is not equal, the replacement of the same cannot be properly planned so that their life-time are fully utilized. In this paper, a dynamic load share control with the use of ABB’s variable speed drive system is proposed, which provides the possibility to the HPGR operator to impact the roller wear in such a way that it equalizes the wear rate to a certain extent and extends the roller life time. Called RollXtend™, this solution includes a load share factor which can be parameterized based on the wear measurement performed manually during maintenance procedure. Additionally, this paper describes an automated load sharing concept based on a non-invasive wear measurement method. The partial results of the technology trial in a copper/gold mine are presented, which aimed at detecting stud damage and estimating the real rollers profile throughout their life time. The final objective of the pilot project was reduce the amount of planned and unplanned downtimes of the HPGR by increasing the rollers life time and avoiding catastrophic stud damages.

Jan 1, 2018

By Christopher Davey, Professor Emeritus, Marian Mazurkiewicz, Peter Kanjorski

The concept of a high pressure liquid jet mill with highly unsteady flow, has been developed and recently patented by Cornerstone Technologies LLC (CsT), for the purpose of micron and sub-micron particle production. The mill accepts feed sizes up to 15mm for some materials and is capable of sub-micron production. Successful material range from precious metals such as silver and palladium to dielectric components and substrates such as Barium Titanate slips, zirconia, titania and silica. The process has also succeeded in adequately reducing the size of materials for both composite and coating uses such as anthracite coal, graphite, chrome metal, wollastonite and more than 100 others. A unique design approach has been taken to highly maximize the energy flux in the mill’s chambers to create extremely high turbulence and destructive cavitation. This is assisted by shock waves, which cause particles to undergo ultra high frequency pressure pulsations, high frequency collisions and then abrasion, shattering, hydro-wedging, and cleaving. Due to these extreme properties the processing occurs in just fractions of a second allowing throughputs up to 1000 kg/h on a machine that would fit inside a 60 cm box. The technical solution and technological advance, as well as the environmental and economic benefits indicate rapid and wide spread acceptance of high-pressure liquid jet milling in modern industry.

Jan 1, 2003

By Brian Hart, Stamen Dimov

"In refractory ores, a substantial part of the gold content may be present as a sub-microscopic component within the mineral matrix of the various carriers. This type of gold may be present as finely disseminated colloidal size gold particles (<0.5µm) or as a solid solution within the sulphide mineral matrix. Such ores are not amenable to gold recovery by direct cyanidation. In order to liberate the sub-microscopic gold, the ore has to be oxidized before being subjected to gold cyanidation and extraction. Autoclave pressure oxidation (AC POX) of the sulphide ore and subsequent cyanidation is a common technology used to liberate the gold in such refractory ores. The additional presence of active carbonaceous matter in such ores (double refractory ores) represents another major obstacle for efficient gold recovery during the process of pressure oxidation and cyanidation. This carbonaceous matter (c-matter) can adversely affect the gold recovery due to its ability to adsorb, or pre-grob gold from the cyanide solution. Advanced micro-beam analytical techniques such as Dynamic Secondary Ion Mass Spectrometry (D-SIMS) and Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) have become powerful tools for characterization of different forms and carriers of gold for the needs of the mineral processing industry. Major advantages of these techniques are related to their ability to analyze individual mineral particles and provide quantitative analysis with detection limits in the low ppm/ppb concentration range. This paper describes various micro-beam techniques and procedures implemented at Surface Science Western (SSW) for quantification and characterization of the sub-microscopic gold and the preg-robbed surface gold as part of full gold deportment studies in feeds and process stream products."

Jan 1, 2014

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014