Search Documents

By H. Hamza, M. R. MacIver, M. Pawlik, L. Malin

"Size and shape are important properties of aggregates formed in engineering processes and natural systems. Measurement of aggregate size or shape is a challenge when the solids concentration is beyond the gel point, ?? > ??g, when the aggregates are in contact and it is difficult to distinguish or segment individual particles in the network. This paper describes the use of a micro-computed tomography (micro-CT) method for the calculation of the aggregate volume fraction, ??, and a characteristic aggregate length, ??a, based on a 3D chord length measurement algorithm. These parameters can be used to quantify changes in aggregate and pore size during a compressive yield stress test to help understand the impact of flocculation and network structure on dewatering. INTRODUCTION In a thickener, flocculation is often used as a pre-treatment step and the final solids content of the underflow depends on the network strength and permeability of the bed formed by settled aggregates (Usher, Spehar, and Scales 2009). This paper describes the measurement and analysis of micro-computed tomography (micro-CT) of flocculated mineral sediments to obtain a characteristic length, ??a, of the aggregate and pore phases during a staged compressive yield stress experiment. This parameter may be used as an indicator of changes in aggregate and pore size to quantify material behaviour in solid-liquid separation processes that depend on self-weight compression or applied pressure. This analysis was carried out to help understand the effect of flocculation on aggregate structure and the thickening process as part of a broader research on the improved solid liquid separation of tailings produced in the oil sands industry.Aggregate properties The solids phase of an aggregated or flocculated suspension will eventually settle – if left undisturbed – under the influence of gravity. As settling of a flocculated suspension continues, the solids volume concentration, ??, may increase to the gel point or gelation threshold (Landman and White 1994), ??g, above which the aggregates form a network of touching particles, or space-filling structure (Kranenburg 1994). In the sediment bed, the aggregates are surrounded by fluid and occupy a partial volume fraction, ??, according to"

Jan 1, 2018

By Kilian Neubert, Wotruba. Hermann, Lars Weitkämper

Metallurgical slags are produced in large quantities all around the world as a result of smelting, refining or alloying processes applied to metals, ores and recycling material. The slag phase serves different purposes in metallurgical processes. It prevents heat losses and protects the metal phases from contaminations and absorbs gangue and extracted impurities. Due to achievable metallurgical efficiencies certain amounts of valuable metal contents always remain in the residual slag. Recycling of these metallurgical slags has several positive effects, such as optimized ecological and economical compliance of the producing industry. If recycled metal contents can be reintroduced into existing processes, required inputs of raw material can be lowered. High metal prices enable the economic recovery of metal contents in metallurgical slags by applying different non-metallurgical processing methods. Conventional processing of metallurgical slags utilizes processes such as hand picking, selective comminution, screening and magnetic separation. Those state of the art processing techniques have limitations in terms of achievable metal recoveries and required energy demand. The approach for an optimized processing of metallurgical slags targets enhanced metal recoveries in combination with lower specific treatment costs. Processes such as coarse and ultrafine density separation, as well as sensor-based sorting as a pre-concentration stage are used to enable an efficient recovery of metal contents in slags. By applying these methods a completely dry working process is possible. This paper reviews the commonly used methods and describes approaches for innovative processing of metallurgical slags to enhance metal recoveries. Focus of this paper is laid on sensor-based sorting as well as on processes for dry density separation.

Jan 1, 2014

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

Almost all of the flotation reagents used today were discovered by continued application of empirical methods and/or trial and error experimentation. Moreover, with the metal-ion specific approach used so far, it is difficult to separate the minerals containing the same constituent metal ion. A critical assessment of molecular recognition processes involved in biomineralization suggested the possibility of using reagents which are surface specific. The concept that the molecules consisting of two or more functional groups having appropriate spacing between those so as to achieve structural/stereochemical compatibility during interaction with the mineral surface exhibit structure-specificity is thought to be extended to the design of specific collectors in flotation processes. In the present study, for the first time, a rational design of surface active molecules, and thereby the recognition of crystal faces (of minerals) by these molecules through structural and stereochemical matching is being utilized successfully to selectively float various minerals. For this purpose, carboxylate-based collectors (for mineral specific flotation of calcium minerals) as well as xanthate-based collectors (for mineral specific flotation of sulphide minerals) with a fixed alkyl chain length but having two functional groups with varying geometrical distances (separated by a spacer of one, two and three carbon atoms) between them have been synthesized. In this article, we have discussed the design, synthesis, purification of these novel mineral specific collectors as well as their important solution parameters in relation to flotation processes.

Jan 1, 2014

Calcium sulfate whiskers are considered to be a prosperous reinforced material in application due to their high mechanical properties. But the hydration occurs easily at moist atmosphere or in aqueous solution. The surface topographies of the calcium sulfate hemihydrate whiskers and the hydrates were analyzed by on-line observation and using XRD. The results indicated the transformation of the crystal type and shape of calcium sulfate hemihydrate whiskers and the reduction of whiskers? aspect ratio. The hydration process of the calcium sulfate hemihydrate whiskers and the effective parameters were further discussed based on FT-IR measurements. The conclusions were obtained that the hydration of calcium sulfate hemihydrate whiskers can be divided into the three phases, namely, initial hemihydration phase, dehydration phase, and coarsening, dissolving and the re-formation of calcium sulfate dehydrate crystal phase. In addition, it was found that in the hydration process of calcium sulfate hemihydrate whiskers the calcium sulfate dihydrate whiskers are formed at first and then converted into the calcium sulfate dihydrate with different crystal shapes, but in the hydration of gypsum hemihydrate the gypsum dihydrate is formed without transition products. The surface active site-calcium ion which has strong trend to react with H2O, the surface ?OH and the inner channels are considered to play important roles in the hydration process of calcium sulfate hemihydrate whiskers.

Jan 1, 2014

By Dilip Kumar Mohanty

In today?s world, Sustainability is the key issue before the mankind. With the ever-increasing population & unimaginable boost in industrial growth to cope up with a steady increase in demand and fast change in life style of a human being, the natural resources are exploited to such an extent that the very existence of living beings in this earth planet is threatened. In such devastating situation, the concept of Sustainability emerges out as a great savior. This concept focuses on minimum/ judicious use of natural resources, thereby preserving the resources for future generation while meeting the bare minimum requirement of the present generation. For an emerging economy like India, Mining and Mineral based industries form the back bone of our economic development. Thus, sustainability of mining and mineral processing industry has a far reaching impact on sustainable economic development of our nation. While at a macro-economic level, we have to strike a balance between economic development vis-à-vis socio-economic & environmental impacts, Industries have to ensure judicious and frugal use of natural resources by making use of energy efficient plants & machineries and adopting befitting technology for reduction & recycling of waste. In the context of the above, it would be interesting to look into the sustainability measures taken up by National Aluminium company (Nalco) at its Crushing & conveying plant at Panchpatmali Bauxite Mine, which is incidentally Asia?s largest Bauxite Mine. In the backdrop of the above stated facts, in this paper the authors make an attempt to bring out the sustainability issues in areas of energy conservation, environmental impact/pollution vis-a-vis mitigation measures adopted in crusher & conveyor plant of Panchpatmali Bauxite Mine & CSR / peripheral developmental activities undertaken by Nalco to mitigate the socio- economic impacts. Keywords: sustainability, energy efficiency, recycle, csr, peripheral development

Sep 1, 2012

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By Kilian Neubert, Hermann Wotruba, Henning Knapp

Sensor-based sorting has been integrated into more and more applications in mineral processing over the past decades. Various sensor types, such as line scan cameras, near infrared sensors and X-ray transmission sensors, allow the separation of a vast variety of raw materials. Sensor-based sorting has several economic benefits which can make the difference between an uneconomic operation and a profitable mine. Sensor-based sorters can be applied to fulfill various sorting tasks, such as waste rejection, product quality improvement and ore type diversion, and have a significant impact on the layout of the processing plant. Therefore, it is important to include sensor-based sorting into the planning of a processing plant at an early stage. To evaluate the applicability of sensor-based sorting for any specific ore type, it is currently necessary to provide several hundred kilograms of material for subsequent bulk tests. In exploration, ore samples are usually rare and only available in form of drill cores. The acquisition of drill cores is time-consuming and expensive especially for deposits in great depth. Hence, it is unfavorable to spoil valuable drill cores for bulk tests. This paper describes a methodology to evaluate the applicability of sensor-based sorting based on drill core analysis. That methodology offers the possibility to calculate the achievable performances of different sensor types for various grain sizes without comminution of drill cores. The general methodology is shown on basis of an exemplary test work on drill cores from a currently conducted exploration.

Jan 1, 2014

By Jan Cilliers

The demand for minerals has never been higher. Moreover, the rate at which this demand is growing is unprecedented, and expansions and new mines will be required to fulfill these growing needs. This, in turn requires a skilled engineering workforce that can develop and operate minerals extraction processes to utilise effectively more complex ores. The International Mineral Processing Council (IMPC) has established a Commission on Mineral Processing Education to consider the global challenge of ensuring an adequate supply of well-trained mineral processing engineers. The Commission has, for the past four years, been collecting international information of the recent mineral process engineering supply position and with a view into the near future. The data collected by the international Commission members are as follows: ? Undergraduate student numbers in minerals engineering ? A breakdown of their male/female ratio ? The fraction of the students from each course that enter the minerals industry ? Teaching staff numbers and age profile This data has been collated and analysed, and the findings are presented. It is clear from the analysis that the supply situation is very different in different regions of the world, and that great opportunities exist for targeted recruitment into the industry to meet the future talent demand. Further, an attempt at correlate the supply of minerals engineers based on the local mineral production rate is shown, which shows that there are clear outliers.

Sep 1, 2012

By L. G. Schumskaya, ?. S. Yusupov, ?. ?. Kirillova

"It has been shown on the example of cassiterite that grinding in mills of the increased power lead to destruction of the fine crystal structure and consequently to change in physical and chemical properties of the mineral, that is its transition into mechanically activated state. The increase in mineral reactivity is related to both the growth of mineral specific surface and sharp decrease in the sizes of primary crystallites accompanied by essential increase in number of microdefects that is clearly expressed in its increasing solubility during interaction with corrosive mediums, especially with acids. Calorimetric measurements indicate that the thermal effect of SnO2 solubility increases considerably.These observations allow us to propose two techniques of hydrometallurgical treatment of cassiterite: direct dissolution of the mechanically activated mineral in acids, although it is a very power-consuming process, and mechanical activation of cassiterite in presence of metals that are able to release hydrogen from acids. Active hydrogen is released during interaction between the mechanical mixture of SnO2 and metal with acids and reduces tin from the mineral transferring it into solution.In addition to other technological properties, the flotability of cassiterite has been thoroughly studied. It has been found that it steadily decreases as activation proceeds because of increase in the degree of hydratability of particle’s surface. In this case, the mechanical activation is provided through tribotreatment of a surface rather than through fine grinding. On this basis we developed the technique of inverse cassiterite flotation with its subsequent transfer into a chamber product that considerably increase the quality of a tin concentrate.The observed technological effects may be generally explained by occurrence of the valenceundersaturated, strained (deformed) chemical bonds and other active centers on the cassiterite surface while decrease in its flotability - by formation of the hydrolyzed tin species and impurity iron, such as Sn(??)4°, Fe(??)2 +, Fe(??)3° hydroxocomplexes and others."

Jan 1, 2003

By A. Güney, G. Önal

"The tailings of the Bigadiç Colemanite Concentrator at the West of Turkey which contain 18 % B2O3 and 1.57 % SO3 are collected at the tailing dams near the Concentrator. In this research, it was aimed to obtain colemanite concentrates with a minimum content of 40 % B2O3 and a maximum 0.5 % SO3 from the tailings. At the experimental studies, decrepitation methods were systematically applied following attrition scrubbing and sizing. At the end of the tests, the best decrepitation result were described, at 500oC temperature for 15 min. duration, the final concentrate having 57.84 % B2O3, 0.44 % SO3 with 73 % recovery was obtained.Boron ores reserves of Turkey are about 2.5 billion tons and Turkey has the 63% share of the World’s boron reserves. The boron reserves are located at Eskisehir (Kirka), Kutahya (Emet), Balikesir (Bigadic) and Bursa (Kestelek) districts in Western Turkey. In 2002, the total amount of boron production of Turkey was about 1.4 million tons, which is 40 % of the World boron production.Bigadiç colemanite (Ca2B6O11. 5 H2O) ore with a content of 30-31 %B2O3 are concentrated by attrition tumbling and classification process. So the final concentrates with contents of 40 and 42 % B2O3 are obtained at the size fractions of –125+25mm and –25+ 3 mm respectively. The tailings materials with an 18 % B2O3 content are collected at the tailing dams near the Concentrator. In this research, it was aimed to obtain colemanite concentrates with a minimum content of 40 % B2O3 and a maximum 0.5 % SO3 from Bigadic tailings having 18 % B2O3 and 1.57 % SO3.In experimental tests, attrition scrubbing, wet sieving, gravity separation, electrostatic separation, flotation and decrepitation were adopted to the colemanite tailings, and optimum beneficiation conditions were obtained."

Jan 1, 2003

By Megha Patel

"The objective of this project was to investigate the application of Prompt Gamma Neutron Activation Analysis (PGNAA) technology to provide real-time on-belt elemental analysis of feed ore in base metal sulphide processing, in this case at the Mount Isa Mines Zinc-Lead Concentrator Heavy Medium Plant (HMP). After initial exploratory testwork proved successful, a Geoscan On-Belt Elemental Analyser was retrofitted onto the existing HMP feed conveyor. Dynamic calibration of the Geoscan was conducted based on laboratory XRF analysis results of the HMP feed conveyor hammer autosampler samples from May to November 2013. Comparison of the Geoscan results to the laboratory XRF analysis results during and after dynamic calibration indicated the technology had acceptable accuracy to be incorporated into HMP process control. The variation between the two sets of data includes all primary sampling, sample preparation and XRF analysis errors as well as the Geoscan errors themselves. The Geoscan instrument precision must be calculated separately through a duplicate sampling campaign and independent laboratory analysis before extending the scope of its range of application beyond HMP process control. The expected benefits of integrating the Geoscan real-time data into HMP process control are optimised HMP metal recovery, improved cost efficiency and improved stability of the downstream processes (milling and flotation). Utilisation of the Geoscan will also enable improved feedback to mines on grade control and dilution, and provide additional information on individual ore types when fed as campaigns to HMP."

Jan 1, 2014

By C. L. Lin

Previous research on particle damage during high pressure grinding roll (HPGR) crushing was limited by the resolution of point-projection micro CT systems and the extent of damage was described by the percent of particles cracked for different crushing methods as determined at a voxel resolution of 40 microns. With recent advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. With the use of X-ray lens imaging the resolution is determined by the lens rather than by the spot size of the micro-focus X-ray source. The high resolution X-ray micro CT (HRXMT) system made by Xradia with a voxel resolution of less than 1 micron is now being used for the characterization of particle damage during HPGR crushing. In this way, the direct 3-D determination of the internal damage of crushed ore particles which vary from 40 mm down to 100 microns in size is being studied at a voxel resolution of a few microns. The number, size, and shape of cracks can now be measured at this improved resolution and for the first time the specific crack surface area distributions of the crushed product can be calculated from HRXMT images using specially designed software tools for 3D analysis. Results from selected crushing operations are presented. Copper ore particles from HPGR crushing at high pressure (6 N/mm2) are severely damaged having crack specific surface areas as great as 10 mm2/mm3. Keywords: HPGR, particle damage, X-ray micro tomography, crack surface area

Sep 1, 2012

By Vishal Shukla, Ashok Kumar, Manas Ranjan, D. Chakraborty, Narayan Sharma

Jigging has a very important role in mineral processing Industry. Upgrading of Iron Ore by jigging has been an emerging trend. A detailed investigation is carried out to understand the influence of Jig feed granulometry and bed height during jigging operation. Noamundi jig plant data shows that variation in jig feed granulometry, feed quality and bed height are major contributors to fluctuation in jigging performance. At Noamundi the feed size (-10.0+0.5mm) fraction is used for fines jigging operation. To understand the effect of granulometrey on jig plant performance such as yield, separation efficiency and Fe recovery. In this context The performance of jigging was evaluated by daily average data from jig operation was used to study the influence of feed distribution on jigging performance .Coarser fraction (+6mm) has a positive influence , whereas fines fraction (-0.5mm) tends to lower performance . During Jigging rearrangements of Particles takes place due to an alternate expansion and compaction of Jig Bed .These particles are arranged by increasing density from top to bottom. During the particle stratification, Jig bed physically cut at desired horizontal particle density plant to separate the desired product. Investigation shows that optimum bed height is required at different Jig feed quality to achieve desired product quality, maximum separation efficiency and Fe recovery. This Paper will illustrate role of granulometry and Bed height control on Jigging plant performance.

Jan 1, 2014

By Christopher M. Rule, Martyn P. Hay

"A methodology was developed in the mid-1980’s to predict plant performance from standard laboratory flotation tests. The methodology incorporates a flotation simulation program “SUPASIM” which translates flotation performance from bench-scale tests to full-scale plant. The technique is based on a simple, empirical kinetics model, and is tailored for use by the practical metallurgist. Kelsall’s unmodified equation incorporating two rate terms describing slow and fast floating components is used as the basis of the method. The flotation behaviour of an ore is described by a set of numbers, which can be compared in the evaluation of ore types, mineralogy and operating conditions. In so doing a precise relationship is developed between metallurgical performance in terms of grade and recovery and flotation kinetics.To date the performance of more than 20 flotation plants has been predicted, encompassing copper, lead, zinc, nickel, phosphate, pyrite, graphite, cassiterite, platinum and various slags. In three cases, plants have treated more than one type of ore. The method has successfully been used to predict and design four flotation plants using data generated from bench-scale laboratory flotation testwork. All have since been commissioned, and have performed as predicted. In the last year alone it has been used to drive flowsheet development for at least seven new plants in South Africa and the Americas. It is also being used to assist in the optimisation of existing operating plants."

Jan 1, 2003

By A. V. Bogdanovich

Until recently, in consideration of fundamentals of gravity concentration theory, all computations have been based on determination of particles? fall velocity in an unrestricted medium (hydraulic size). Meanwhile, gravity separation processes are realized under conditions of particles? restricted fall, when important and sometimes decisive role is played by interacting forces of particles, dependent on their varying size, density and shape, i.e., segregation forces. We have developed devices and methods for measuring segregation velocities of fine particles of various size, density and shape during their loosening in air or aqueous medium. Besides, to exclude influence of medium upward flows, loosening was provided by superposition of vertical harmonic oscillations on measuring cell. It was established, that maximum segregation velocities are observed at certain optimal acceleration values and amplitudes of oscillations; excessive loosening leads to mixing and worsening of segregation. Velocity of some particles segregation through others depends on particles? size, density and shape, as well as nature of medium (air, water). Absolute segregation velocities of particles in air medium may reach 1~2 mm/s, in aqueous medium such velocities are by an order smaller. Analysis of rare-metal sands material gravity concentration results showed, that owing to segregation process during gravity separation, fine-size isometric particles of heavy minerals are recovered into gravity concentrates more actively, than larger ones, but more elongated in shape. It is convenient and simple to estimate mineral grains? shape by extent of their oblongness, described as ratio of particle minimal dimension to maximum. Besides, mineral mixtures gravity separation results are directly related to extent of oblongness of heavy particles, recovered in gravity separation process, and also to root-mean-square coefficient of their shape variation. The performed research showed that particles segregation in gravity concentration process plays not a lesser role, than hydrodynamics parameters, and demands further theoretical inquiry and experimental studies.

Jan 1, 2014

By V. A. Ignatkina, V. A. Bocharov, T. I. Yushina, I. M. Petrov, A. A. Kayumov

"The purpose of this research was aimed at increasing recovery of metals from rebellious sulfide polymetallic ores of nonferrous and rare metal deposits. The ores under consideration have common processing features, including textural and structural complex characteristics, irregularity of impregnation and wide range of grain size, up to nanoparticle size, variable complex mineral composition, low content of precious metals etc. This all predetermines the need for advanced processing schemes with deep selective liberation and separation of minerals with intercycle release into rough concentrate and fractional products with the use of multi-stage cycles of individual dressing, based on an optimum combination of various integrated beneficiation and hydrometallurgical processes. The application of existing standard processes does not enable the production of high-grade selective concentrates without reducing the recovery rate due to incomplete separation of fine mineral intergrowths and overgrinding of brittle ore and rock minerals.The combined beneficiation processes for such type of resources, aimed at increasing recovery of nonferrous, rare, and precious metals are based on flotation methods in combination with gravity concentration to produce rich rough collective or selective concentrates, comprising readily floatable mineral fractions. At the same time, hardly recoverable and non-separable mineral associations are released into separate concentrated products for following dressing by individual processes. The proposed combined process provides for successive selective liberation of minerals with release of rich readily recoverable mineral fractions at the preparation and ore beneficiation stages. The hardly recoverable mineral associations shall be released in subsequent operations with the use of dressing, based on a combination of beneficiation and pyro- and hydrometallurgical methods."

Jan 1, 2018

By Dietmar Freyhammer

Grinding is the last stage of the comminution process. In the grinding process the particles size are reduced by impact and attrition stresses. The fine grinding of ores is nowadays finding increased application due to depletion of coarse grained, easily processed ore bodies and the increased need to process distributed fine grained deposits, such fine ground iron ore powder is the basis for the pelletisation process. Depending on the ore type and the project environment different approaches to comminution are requested to provide an adequate ground iron ore for the pelletisation process. Currently the ball mill is the most used equipment in grinding iron ore for pellet feed. Based on the various examination and investigation of minerals on grind ability related to the throughput, to the resulting sieve characteristics and necessary energy consumption, the mill circuit can be: Open dry circuit. Closed dry circuit Open wet circuit Closed wet circuit. CEMTEC GmbH is a renowned name worldwide and offers tailor made solutions to cope these issues.

Sep 1, 2012

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

By Magnus Evertsson, Rebecka Stomvall, Josefine Berntsson

"Understanding the effect of particle shape on dry rheology is considered to be an important aspect in order to replace natural sand used in concrete with manufactured sand. Crushed particles from solid rock are normally less rounded and have less equally shaped dimensions compared to natural sand. Thus, the flowability and workability of the concrete will be different. In previous research, it has been demonstrated how different crushing techniques affects the shape of the particles. In many cases it is believed that Vertical Shaft Impact (VSI) technology is a way forward to replace natural sand. To be able to study the effect of VSI at the smaller fractions (63-2000 µm) sufficient measurements methods to determine particle shape are required. Optical tools to analyze the aggregates would make it possible to study a large amount of particles at small fractions. The determination of particle shape of aggregates is challenging since the shape is highly irregular and the size span of particles are very large. This study aim to evaluate one of the available optical tools, the Camsizer, for digital imaging determination of shape and size distribution. The available default shape parameters of the Camsizer are studied to understand the meaning of the parameters and their suitability for determining the quality of manufactured sand. To evaluate the capacity to determine particle shape, tests are made with 35 different materials. The results are compared with the dry rheology measured with the standardized "flow cone" test. Dependence has been previously proven between particle shape and the mass flow rate in the cone. Three different shape parameters, aspect ratio, sphericity and symmetry, are studied with the Camsizer and the results are compared with the mass flow rates in the cone. The results indicate a strong linear relationship between the optical parameters and the flow cone test."

Jan 1, 2014