Search Documents

By D. W. Fuerstenau

Understanding how cationic surfactants affect the interfacial behavior of quartz is important in mineral processing and environmental engineering. This paper presents the results of a study of the effect of the molecular structure of cationic surfactants on the interfacial behavior of finely ground natural quartz. Most of the experimental work involved the determination of zeta potentials and the stability of quartz suspensions. Some measurements of induction times and the flotation response of coarser particles are also included. How these surfactants affect interfacial behavior is discussed in terms of adsorption mechanisms. The molecular structure (number of hydrocarbon chains, type of ionic head group, number of ionic head groups on the molecule) of these reagents was found to significantly affect their surface activity.

Jan 1, 2014

By N. D. Dementieva

Based on lab and pilot-plant tests to recover gold, silver and lead of a Russian deposit, a collective and flotation concentration flow sheet with lead and sulfide concentrates was proposed. The type of the deposit is gold-sulfide-quartz-bearing. The recovery of gold, silver, and lead to a lead concentrate was 47.4%, 68.1% and 70.7%, respectively. The grade of gold and silver grade was 170 g/t and 372 g/t, respectively. The mass percent of lead, zinc and arsenic mass percent was 41.7%, 0.34% and 0.63%, respectively. The recovery of gold and silver recovery to a sulfide concentrate was 50.1% and 28.8% at the grade of gold 20.5 g/t and silver 66.2 g/t. Sulfide concentrate with arsenic mass percent ~3% was biooxidised followed by CIL and obtaining metal at the site as well as zinc concentrate from bioleaching solutions with zinc mass percent 45% at its 64% recovery. The total gold and silver recovery using a developed technology with the account of their treatment at a polymetallic plant was 92.2% and 93.7%, respectively.

Sep 1, 2012

By Häkkinen Antti, Salmimies Riina, Matveinen Maria

"Tailings generated during the upgrading of ore present a major challenge for the mineral processing industry. On one hand, the processing of tailings requires added capital input. On the other hand, increased difficulties in obtaining permits for dams and landfilling and increased costs associated with storage and tailings management also result in increased costs. To promote sustainability and make tailings management economical, added value must be generated from the waste material. This might be possible through the recovery of the metal values in the waste. This work discusses the possibilities of recovering metals from multimetal tailings through leaching in a stirred tank. The characteristics of the tailings are crucial and the distribution of the metals within the different size fractions is used to identify the most attractive route for the hydrometallurgical step. Leaching of nickel and copper is further investigated using acids at different concentrations. The leaching of base metals is possible at acidic conditions. Increased temperature and concentration of the leaching agent promote the dissolution of the metals, as could be expected. With simultaneous dissolution of several metals the dissolution mechanisms are difficult to identify. Furthermore, as several metals, not all of them being target elements, are leached another challenge arises from the selective recovery of those metals from the liquid phase."

Jan 1, 2014

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By David Deglon, Martin Harris, Mehdi Safari

This paper investigates the effect of energy input on the flotation of galena in a novel oscillating grid flotation cell (OGC). Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Previous work was limited to quartz (-100 µm). Galena (-150 µm) was floated in the OGC at power intensities from 0.5 to 3 W/kg using 0.13, 0.58 and 0.82 mm mean bubble sizes (d10) and at three collector dosages. Results show that the effect of power intensity on flotation kinetics is strongly dependent on both particle and bubble size. For fine particles (-19 µm), increasing energy input increases the flotation rate at a low collector dosage but leads to an optimum at both the moderate and high collector dosages. For intermediate particles (+19-38 µm), increasing energy input has no effect on the flotation rate at the low collector dosage but leads to an optimum at both moderate and high collector dosages. For coarse particles (+38-150 µm), increasing energy input has no effect on the flotation rate at the low collector dosage and leads to a general decrease at both moderate and high collector dosages. Optimum conditions for fine particles are using small bubbles at a moderate collector dosage and an energy input of around 2 W/kg. Optimum conditions for moderate particles are using small bubbles at a high collector dosage and energy inputs of around 1.0 W/kg. Coarse particles do not benefit from agitation.

Jan 1, 2014

Spent automobile catalyst is an important secondary resource of PGMs (platinum group metals) and the recovery is significant. Various methods of recovery technology have been reported and applied in practical production, including pyro- and hydrometallurgical processes. Since the grade of PGMs in the catalysts is so low, approximately 0.5 wt. %, the present recycling technologies require high energy-consumption, it is of great significance to enrich the PGMs with some energy saving physical separation methods as a pretreatment. Automobile catalyst is usually composed of cordierite phase as a substrate and alumina phase, with PGMs, which covers the cordierite phase. We adopted the quenching pretreatment, one method of thermal shock, to generate micro-cracks between the two phases and separate the alumina phase from cordierite. Quenching was carried out by heating the catalysts in an electric furnace of different temperatures followed by rapid soaking into cold water. It was found that the phase boundary between alumina and cordierite was broken in the quenching and selective separation (detachment) of alumina from the cordierite could be achieved in the following surface grinding. The effect of quenching was checked by microscopic observation, hardness measurement, and chemical analysis. This paper figures out the stress formula of the quenching process, which is largely connected with layer thickness and temperature gradient by using an FEM (Finite Element Method) simulation and clarifies the mechanism of crack generation in the quenching process. Keywords: automobile catalyst, PGM, quenching process, FEM

Sep 1, 2012

By A. Morrison, P. Brito-Parada

"The separation of valuable and gangue minerals according to their surface hydrophobicity in a froth flotation tank occurs in both its pulp and froth phases. In the pulp phase, hydrophobic particles must be brought into contact with rising bubbles introduced at or near the bottom of the tank. In a mechanical froth flotation tank, this is primarily achieved through the agitation of the pulp by an impeller or by a rotor-stator system. However, the turbulent and mixing effects of such an impeller or rotor-stator system, necessary to promote bubble-particle interactions in the pulp, are not confined to the pulp zone, but are transmitted into the froth zone at the pulp-froth interface. This impeller-induced turbulence at the pulp-froth interface is compounded by the impulse of buoyant bubbles entering the base of the froth phase, reducing the stability, and thus separation performance, of the resulting froth. Hence, turbulence improves separation performance if it occurs deep in the pulp phase, but diminishes it if it occurs close to the pulp-froth interface. For this work, a performance-enhancing pulp phase insert was designed to isolate the impeller-induced turbulence from the pulp-froth interface in a laboratory-scale, continuously-operated froth flotation tank. The result was a shifted grade-recovery curve that allows the insert to be designed to maximize the recovery from the system without sacrificing the grade of the concentrate, or vice versa, along a spectrum of improved performance. This paper will present the insert design and development process that resulted in this improved grade-recovery curve, as well as a set of heuristics that could be used to design a similar insert for pilotand industrial-scale validation and deployment.INTRODUCTIONAn almost ubiquitous design feature of commercial flotation tanks is the enclosure of the impeller to create a concentrated turbulent zone (Mavros, 1992). These turbulent zone enclosures are varied-- from the rotor-stator design of, for instance, Outotec cells, to the air disperser design of Wemco cells-- but all share the same rationale: that turbulence is desirable to promote bubble-particle interactions (Ralston, 1999), and to produce smaller bubbles (Wills, 2006), but also undesirable because it promotes the detachment of valuable mineral particles from bubbles, and exacerbates entrainment-inducing mixing at the pulp-froth interface (Jameson, 2010)."

Jan 1, 2018

By Fu Ping-Hao, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton’s Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

By Yi-jun Cao, Jin-cai Ran, Guo-sheng Li, Jiong-tian Liu, Li-jun Deng, Shu-lei Li

A fly ash sample from a power station in Guangdong province has been characterized by size separation, X-ray diffraction, contact angle measurements and X-ray Fluorescence. The ash sample had a loss-on-ignition (LOI) (%) of 15.54% and a large proportion of the unburned carbon was distributed in the +74 µm and -20 µm fractions. Contact angle measurements suggested that the removal of unburned carbon from the fly ash using flotation would present some challenges. The effects of various operating variables on the removal rate of unburned carbon (RUC) (%) and (LOI) (%) were determined using a cyclonic-static micro bubble flotation column (FCSMC). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil (frother) dosage was 600 g/t, pulp density was 20%, superficial gas velocity was 1.4 cm/s and circulating pressure was 0.20Mpa. Column flotation tests indicated that the FCSMC method a viable and effective separation process for removing the unburned carbon from the fly ash. Under the optimized conditions, a clean ash with 2.13% LOI and 94.21% RUC was obtained.

Jan 1, 2014

By Jorge Misle, Daniel Silva

"This paper addresses the need for advanced control technologies and strategies in the mining industry, its potential and actual impact on mining processes and the best practices for their implementation, operation, and long term sustainability. It is well known that advanced process control (APC) can be a very good source for incremental process improvement for the mining industry, yielding to higher production rates or helping maintain consistent production rates despite ore changes. The application and integration of new technology, process knowledge and innovation are key elements in building such a supporting structure. More specifically, and this cannot be emphasized enough, the correct application and assembly of control tools, the in-time presentation of key data to decision makers and the development of relevant statistics and KPI’s (key performance indicators) can and will make a difference not only in terms of production, but also in plant stability, availability and production costs. In deploying such ideas and aiming at the long-term goal of "Operational Excellence", Minera Los Pelambres (MLP) has developed a number of successful control strategies, best practices and technologies, which are not only the application of state-of-the-art automation and computing tools, but rather the assembly of the above presented structuring factors. This work discusses some of the key tools and ideas implemented for SAG & Ball milling and Flotation areas, their performance results and the roadmap taken for the integration of process knowledge and control tools. Also, cases studies are presented and discussed further to not only show the main areas of improvement, but also to highlight the benefits of such strategy that for the most part, deviate from the traditional mining industry control approach. Also, a word is given on the need for innovating in the design of control strategies and leveraging best practices and process knowledge that ultimately, will contribute to long-term reliable operations, improved mineral processing and, although unmeasured, lead to a superior overall performance and productivity of all mining personnel involved."

Jan 1, 2014

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018

By M. Alvarez-Silva

The control of the amount of chromite reporting to the concentrate during the flotation of UG2 ore is of critical importance since its presence affects the downstream smelting process. It is generally reported that the main mechanism responsible for chromite recovery is through entrainment. This is reflected in analyzing the solids and water recoveries. These in turn are strongly dependent on the froth phase. In the present investigation a laboratory scale column flotation cell was used to investigate the role of the froth phase in the flotation of UG2 ore. Such a device is superior to a standard batch cell since it operates at steady state in open circuit and also allows for a greater degree of flexibility in terms of froth heights. The mass of solids and water recovered in the concentrate as well as chromite (Cr2O3) recovery by size class was determined as a function of froth height, superficial gas velocity and depressant dosage. The results showed that depressants had little effect on chromite recovery but increased the grade due to the depression of gangue minerals. A 60cm froth height always resulted in slightly lower solids, water and chromite recovery than for 30cm. Typically only 20-25 % of solids reaching the pulp-froth interface reached the launder. The relationship between solids and water recovery for a wide range of conditions indicated that chromite is mostly recovered by entrainment. Keywords: UG2 ore, column flotation cell

Sep 1, 2012

By Komar Kawatra, Joseph Halt

"Bentonite clay has been the traditional binder for iron ore pellets. However, bentonite increases pellets’ silica contents and is expensive. Researchers have proposed lowering bentonite doses by mixing it with other common binders. These mixtures may only be successful if the fundamental bonding mechanisms are understood. For example, what happens when bentonite (physical bonding) is mixed with fly-ash (chemical bonding)? What happens when bentonite is mixed with cornstarch (physical bonding)? In this paper, experiments are described where bentonite was mixed with various ratios of cornstarch and fly-ash, and pellets were agglomerated using 0.66 % w/w binder. Ca(OH)2 and CaCl2 were added as activator and accelerator, respectively, to the bentonite-fly ash mixture. Curves of pellet dry strength vs. bentonite-starch ratio were linear, suggesting the physical-physical bonding mechanisms were compatible - acceptable strengths (> 22 N) were produced at all bentonite-to-starch ratios. This was contrary to bentonite-fly ash mixtures, which displayed dry strength curves with a noticeable minimum due to competing binding mechanisms. Bentonite alone and fly ash alone produced acceptable strengths (> 22 N), but their mixtures resulted in weak pellets. Due to the positive results using cornstarch (CS) binders, the effects of CS solubility in water were investigated using two CS with high and low solubility (60 and 7.5 %). CS was premixed with bentonite at various ratios (0, 20, 40, 60, 80, 100 %). Pellets were agglomerated using 0.66 % w/w binder. The dry strength of pellets ranged from 50-300 N using the high solubility CS mixtures, and from 50-85 N using the low solubility CS mixtures. Fired strengths exceeded 2200 N/pellet at all bentonite-cornstarch ratios. This research showed that cornstarch solubility is an important factor in determining its effectiveness as a binder for iron ore concentrates, but significant work is still necessary before it can be used as a bentonite replacement."

Jan 1, 2014

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By C. Tokoro

Co-precipitation of dilute toxic anions with ferrihydrite is an important removal mechanism in wastewater treatment system. Although, numerous qualitative studies have been published on removal characteristic from wastewater of dilute anions by co-precipitation treatment, detail mechanism or quantitative characteristic is not well understood. This paper discussed the co-precipitation mechanism of As(V) and Cr(VI) with ferrihydrite by comparative experiments between co-precipitation and simple adsorption. In this study, co-precipitation experiments and simple adsorption ones were distinguished closely. In the former, precipitation of hydroxides and adsorption of anions develop simultaneously, but in the latter, anions adsorb onto prepared hydroxides. Although high affinity anions for hydroxides (e.g. As(V) for ferrihydrite) showed quantitative difference of removal ratio between co-precipitation experiments and simple adsorption ones, low affinity anions (e.g. Cr(VI) for ferrihydrite) showed quantitative agreement in spite of deferent forms of ferrihydrites between them, that is, amorphous ferrihydrite was formed in co-precipitation experiments, but goethite was formed in simple adsorption ones. In order to discuss the mechanism of co-precipitation phenomena, three experimental studies have been carried out: (i) adsorption isotherm measurement in the co-precipitation experiments of As(V) or Cr(VI) with ferrihydrite, (ii) zeta potential measurement of co-precipitated or simple ad-sorbed ferrihydrite with As(V) or Cr(VI), and (iii) XRD analysis of co-precipitated As(V) for ferrihydrite. All experimental results suggested the main mechanism in co-precipitation phenomena of As(V) was not only a surface complexation (simple adsorption) but also a surface precipitation.

Jan 1, 2014

By B. Rath

An effective process plan is an important part of maintaining consistent recoveries in mineral processing operations. Traditionally, Mineralogical studies are completed using chemical and metallurgical methods to monitor recovery and elemental distribution. The development of mineralogy and more efficient processes in mineral analysis techniques means that mineralogy is now more accessible as an efficient and comprehensive study tool. As operating costs increase and feed grades decrease it is important to maintain tight control of process and ensured maximum recovery is maintained at all times. Just a few days of losses in recovery caused by changes in ore type or processing conditions can have a large effect on total metal recovery and profit. Mineralogical audits can be used to minimize these losses by monitoring the fundamental behavior of feed ore on a regular basis. Smart use of mineralogical studies can develop mineralogical and ore type benchmarks in a detailed, which can be used in process control and monitoring. Geological ore types can be used to identify key mineralogical parameters that may be used in routine and cost effective analysis. Mineralogical systems ideally suited to this because of the depth of information on everything from modal mineralogy to locking/liberation characteristics and mineral associations. Mineralogical studies can equally be applied to specific unit operations within the process, which can allow more detailed information to be gathered on areas of the process that have been identified as critical. This will be especially effective for flotation or oxidation processes where process parameters can be very sensitive to small changes in mineralogy. This paper deals with the Ore Morphology, Ore Mineralogy, Gangue mineralogy, Photo micrographs under reflected, transmitted light and XRD studies Ore, Mineral studies of Sub grade Iron ore of Bacheli Complex, Bailadila Sector, India. Keywords: mineralogy, liberation, liberation studies, ore mineral, gangue mineral, morphology, jasper, ferruginous clay

Sep 1, 2012

By Jaime Sepúlveda

"A broad diversity of critical operating conditions may influence, in very convoluted ways, the actual performance of any given mineral processing system, to the extent that it becomes nearly impossible to empirically determine the independent, decoupled impact of each condition. An effective approach to better understand the behaviour of such complex systems is via the extensive use of sufficiently detailed and reliable mathematical models, allowing the process analyst to explore and learn about the independent effect of all relevant operational conditions. Certainly, these tasks are greatly facilitated if the appropriate software tools - such as the Moly-Cop Tools software package - are readily available. Moly-Cop Tools 3.0 is a set of 63 easy-to-use EXCEL spreadsheets designed to help process engineers characterize and evaluate the operating efficiency of any given grinding circuit, following standardized methodologies and widely accepted evaluation criteria. Moly-Cop Tools 3.0 covers conventional and semiautogenous mills, crushers, HPGR’s, rod mills and vertimills, with the corresponding mass balance and parameter estimation routines; plus complementary spreadsheets regarding Bond’s Law calculations, grinding media selection and performance evaluations and other useful utility functions. As a relevant example of application, specifically focusing on semiautogenous grinding operations, the current publication describes how the models can help us learn and rationalise critical empirical observations such as the relationship between feed particle size and optimal ball filling, the role of the rocks as autogenous grinding media as well as the impact of feed size and discharge grate opening on the mill grinding capacity. Over the last 20 years, Moly-Cop Tools has gained wide acceptance around the mineral processing community in recognition to the quality of the mathematical models contained, their simplicity of application and ease of sharing of the calculations amongst all interested parties, since it is available free-of-charge with no restrictions to make as many copies as needed."

Jan 1, 2014

By H. Gallardo, J. Yianatos

Flotation is a separation process in which mineral recovery depends on the particle surface properties. The selective collection of particles by air bubbles requires hydrophobic mineral surfaces. Hydrophobicity can be selectively induced on a valuable mineral surface by means of reagents. For this purpose, it is required that mineral grains in the ore become physically liberated or exposed in the particle surface after grinding. The grinding process generates three types of particles according their exposed surface in the floatable mineral: locked particles (0-10%), associated particles (10-90%) and liberated particles (90-100%). Locked particles have low floatability, and they typically show low recovery (<20%), while liberated particles have a high floatability and can be easily recovered (98-100%) at different particle sizes (10-150 µm). The main challenge in the flotation process is the recovery of associated particles. These particles typically have recoveries of 20-80%, but strongly depend on the particle size, particle surface liberation and collector dosage. Recent studies on particle floatability by size-liberation have significantly contributed to improving the characterization of flotation processes. In this work, a study of flotation recovery of associated particles of 10-90% liberation is presented for particle sizes (10-150 µm) and collector dosages (5-40 g/ton). In this work historical data on galena recovery based on particle cross-section composition of galena was used, assuming they represent an acceptable estimate of particle surface composition, as shown by some previous researchers. The results showed that galena recovery can be well represented by a model consisting of the interaction of a linear function and a Gamma distribution function to account for the liberation and the particle size effects. Consequently, an alternative approach for modelling the recovery of associated mineral (10-90% liberation), with a reduced number of parameters, was developed and validated.

Jan 1, 2018

By Vladimir S. Zharov, Vyacheslav A. Tsukerman

"Conceptual imitative dynamic model of developing enterprises for medium and long-term period permitting to ensure coordination of interests of the enterprise and territorial environmental authorities has been developed to enable the process of the prognostication and management of a concentrating mill development, in which a symbol language and terminology familiar to the manager of the company are applied. An algorithm of practical application of this model of company development was elaborated as well as a general methodological approach to the prognostication of the development and procedures of its implementation. The general methodological approach to the implementation of the model has been defined. Within the framework of system approach, a concentrating mill is considered as a subsystem of an ore mining and processing company or a mining and smelting one. A concentrating technology is considered in dynamics, its change is determined by the task of making the company operation profitable. Technological indicators are secondary relative to financial and economical indexes. At the same time, technological and economical indexes are determined in their interrelation with ecological parameters. The elaborated model allows us to estimate all necessary economic, financial and technological indexes in their interrelation both for the company as a whole and as separately redistributed estimating the basic prognostication documents - accounting balance-sheet, profit and loss report, as well as the funds flow statement. When varying the managing parameters, all necessary result-producing financial and economical indexes are estimated and a need in and a possibility of an external funding by various sources are considered.The implementation of the model enables one to determine the required scale of production capacity, as well as the amount of raw-material resources needed. In case of shortages of the latter, there should be considered various scenarios of the production capacity enhancement or the possibility of commissioning of new sites or deposits and introduction of improved technologies."

Jan 1, 2003

By Peter J. Scales

The recovery of water for re-use in minerals processing is an important issue in the reduction of water use in mining, as is the dewatering of tailings to reduce the propensity of ?wet? tailings dams. It is common in these dewatering operations to use thickeners whereby polymeric flocculants are combined with the dilute feed to the thickener to aid sedimentation and the subsequent consolidation of particulate materials. Thickeners are the workhorses of water recovery and tailings dewatering and although the basics are well understood, there is still no ability to reliably predict the throughput and underflow density from a thickener based on traditional sedimentation tests and flux analysis. The reasons for the discrepancy between full-scale operations and predictions based on laboratory tests are numerous, including difficulties in mimicking the flocculation conditions experienced in the field and the shear conditions in the thickener. The latter effects are little understood and hard to quantify and include effects due to flocculated aggregate densification, complimentary shear and compressional effects and aggregate break-up. Developing a set of test protocols to quantify the effects of densification, shear in compression effects and aggregate breakup and the subsequent contributions of each to compressional dewatering in a thickening environment has been completed for a simple model polymer flocculated particulate suspension. The data and analysis shows that aggregate densification is a dominant contributor to the difference between observed and predicted behavior based on laboratory tests. A major consideration in the analysis is the fact that common thickener operations are permeability limited and although the various effects are all important, the one that results in the fastest water release is dominant. Of interest also are the shear rate, concentration, and time dependence of the aggregate densification process. A basic model of the process has been developed along with network yielding tests conducted using rheometry. Keywords: compressional dewatering, gravity thickening, rheometry, aggregate densification, raked batch settling

Sep 1, 2012