Search Documents

By Z. G. Song, C. Y. Sun, X. R. Zhang, Y. Yu

In skarn type scheelite deposit, there are calcium minerals with floatability similar to scheelite, such as calcite, fluorite, etc., which are difficult to separate. Heating cleaning method developed by Petrov has been widely applied in processing rough concentrate of scheelite for nearly half a century, but there exists a general lack of full understanding of the interaction between floatation reagent and mineral particles surfaces. The mechanism on separation of scheelite and calcium minerals in heating cleaning process was investigated by mineral flotation experiments, XPS analysis, as well as solution chemistry and crystal chemistry calculations. The results showed that the sequence of minerals floatability using sodium oleate as collector and a large amount of sodium silicate as modifier in heating flotation test was scheelite > calcite > fluorite, which was the same as solution chemistry calculations based on Gibbs free energy vs. pH and also the same as Ca-X intensity order by crystal chemistry analysis. There are two sides about the mechanism of heating cleaning method: one is that the adsorbed collector on calcium minerals surface is desorbed more easily than scheelite, and the other is selective dissolution of calcium ions from the mineral surface because of Ca-X intensity difference in heating and stirring process.

Jan 1, 2014

By S. V. Bogdanov, S. I. Grishaev

"The article presents the materials about the appropriateness of the use of rental indices to assess the effectiveness of the use of deposits of rare earth elements (REE). The authors suggest from the standpoint of rent payments to rate for the owner the possibility of using the anticipated rental income as the indicator for the analysis of preferences and economic significance of enrichment of extracted raw materials in the emerging field of rare earth metals (REE). Usually from ore mined at the fields, for flotation technology to produce concentrates with collective REE, then they are subjected to chemical-metallurgical processing of the received products are divided into pure oxides, chemical compounds or isolated from them pure metals and alloys. This commercial product is shipped to the buyer. REE were a non-renewable natural resources, so the calculations for determining differential and specific rent showed that during the development of the technologies of mineral processing of a specific field it is necessary to consider what the expected rental income depends on the magnitude of differential rent is related to the volume of production of REE for the whole planned period of exploitation of natural resources. This income is determined by the amount of stock field. For long-term exploitation of the deposit is observed in almost direct proportional dependence between the annual differential rent and the rental income. The decrease in rents in the long run is determined by the change in the composition of ores included in the extracted raw materials and the balance between light and heavy REE. The largest 70% reduction of the rent projected for ""cerium"" fields, while for ""yttrium"" these losses are considerably smaller. Tomtor, Chuktukon and Katuginskoye Russian deposits are characterized by a level of rent that is comparable to the mastered foreign sources of REE. Thus, the enrichment of minerals with REM in the domestic deposits is quite competitive at the world level. INTRODUCTION Deposits of rare earth metals (REE) are non-renewable resources that should be developed and used so that it would be possible to provide a reduction due to payment of appropriate resources for future generations. This compensation, due to the reduction of natural resources, can be carried out both in natural and in economic terms (1). When analyzing economic compensation options, particular attention should be paid to rental income in assessing the attractiveness of using different REE deposits. It is known that absolute and differential rents are summands when calculating the value of natural rents. The value of the absolute natural rent is proportional to the unit price of the product obtained from mineral raw materials and sold on the commodity market. Limitations, as well as the use in production processes and business, contribute to the gradual reduction of natural resources, which increases their consumer value and affects the price of commodity products from primary raw materials."

Jan 1, 2018

By Gabriela Pino, Maurício Torem, Diego Veneu

Because of its simplicity, economy and biocompatibility, research regarding the use of microorganism for decontaminating heavy metals produced by many industries is an area of growing interest. Also, there is a stringent need for the control of toxic metals produced during various production processes and released into the aqueous environment in order to avoid damage relevant to soil or groundwater contamination. Among the available treatment technologies, sorptive flotation has been considered as a promising alternative for the wastewater treatment. In the present study Streptomyces lunalinharesii strain was applied as bioreagent for the removal of copper, cadmium and zinc. The removal of those metal ions depends mainly on the respective pH value, influencing the aquatic speciation during the process, as well as the zeta potential of the system and biomass concentration. Langmuir and Freundlich isotherms have been depicted. Dispersed air flotation was applied as the subsequent separation method for harvesting the suspended metal laden microorganisms, following the biosorption of copper, zinc and cadmium. The investigated parameters (in batch mode, laboratory scale) were in this case the saturator pressure, the coagulant concentration and the recycled flow. Applying the optimum defined conditions, over 60% removal of metal ions have been achieved in one stage and simultaneously, quantitative separation of the used (metal-loaded) biomass has been obtained.

Jan 1, 2014

By Tuan V. Nguyen, Kosta Simic, Louis Mittoni, Murray Rudman, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D .Improving Thickener Technology. project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By Xiaodong Jia, Williams. Richard A.

This paper describes the recent developments, arising from research at Leeds, in the computer modelling of packing of complex shaped particles and prediction of physical properties of the structures represented by the packing. The computer model DigiPac, is capable of packing particles of any shapes and sizes in a container of arbitrary geometry. The ability to predict packing structure of real particle shapes and to compute directly some structure-dependent physical properties (such as liquid permeability, mechanical strength/ stability, compaction and sintering, dissolution and leaching, etc.) is obviously highly desirable and has significant potential in industrial applications. Examples are presented relating to the packing of granular materials.

Jan 1, 2003

By André Mans, Frans B. Waanders

"Ferrosilicon (Fe-Si) is an important commercial material and it forms the basis of the powder used in dense medium separation (DMS) of various minerals in a minerals beneficiation process. Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof.A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. The SEM analyses of the Fe-Si yielded a composition of 15 wt.% Si and 85 wt.% Fe with minor impurities of Mn and Cr (<1 wt. %), resulting in an ordered phase with a calculated composition of Fe2Si. The average density of the Fe-Si was found to be 7.177 g.cm-3 whilst the size distribution was determined with the d50 of the particles being approximately 30 µm. A slurry, containing 10% solids was prepared, which had a density of about 1.1 g.cm-3 and this slurry was used to conduct the various experiments under laboratory conditions at the university. Samples were taken at regular intervals from a storage container containing a lime solution as well as from a closed circulation circuit system, kept at a constant temperature of about 60°C. Mössbauer Spectroscopy yielded, for the new fresh Fe-Si-samples, a two-sextet spectrum with hyperfine magnetic field strengths of 19.9T and 30.7T respectively, and the yellow-brown froth was found to be akaganeite or ß-FeOOH.It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought."

Jan 1, 2003

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By Ibrahim Alp, Duygu Dinç, Ersin Yazici, Adularya Energy and Electricity Generation and Mining Inc., Oktay Celep, Haci Deveci

Thiosulfate leaching as an environmentally benign alternative to cyanide leaching has received particular attention in recent years. Most studies have focused on thiosulfate leaching of free milling ores and, to some extent, pregrobbing ores. In this study, leaching of gold from the refractory Kaletas ore (in which gold/silver alloy is the only mode of occurrence detected) in ammoniacal thiosulfate solutions was studied. A two-level full factorial design (23) was adopted to investigate the effects of concentration of thiosulfate (0.2-1 M Na2S2O3), ammonia (0.5-1 M NH3) and copper (0.05-0.1 M CuSO4) on the extraction of gold from a ground ore (-38 µm) over a period of 24 h. Statistical analysis confirmed the leaching of gold improved with increasing concentrations of thiosulfate and ammonia. In contrast, increasing the concentration of copper in the range tested adversely affected the extraction of gold. The magnitude of effects of parameters on the gold extraction was in the order of Na2S2O3 > NH3 > CuSO4. The maximum extraction of gold (69.6%) was obtained in the presence of 1 M Na2S2O3, 1 M NH3 and 0.05 M CuSO4. The negative influence of copper on gold extraction is most likely attributed to the decomposition of thiosulfate catalyzed by copper. Concentration of thiosulfate was also identified to be statistically the most important parameter for its consumption.

Jan 1, 2014

By Y. F. Guo

Among the different valences of vanadium, V (?) is insoluble in acid, V (?) and V (?) is in-soluble in water but soluble in acid. Vanadium mainly exists as V (?) in vanadium titanium-rich material obtained by reduction -milling-separation from vanadiferous titanomagnetite. Therefore, the vanadium titanium-rich material can not be used to extract vanadium by acid directly. In this paper, the vanadium leaching was studied by oxidation roasting and acid leaching. Through oxidation roasting, vanadium is transformed from the insoluble V (?) into V (?) or V (?) in order to improve the leaching of vanadium. The results show that vanadium leaching increases significantly by oxidation roasting-acid leaching. Leaching of vanadium is up to 70.18% under the optimized conditions of roasting temperature of 950 ?, roasting time of 40 min, sulfuric acid concentration of 40%, leaching time of 4h, leaching temperature of 95 ? and liquid to solid ratio of 4 : 1.

Jan 1, 2014

By I. V. Makarskii, D. N. Nikitin, L. G. Tarasova

"The extent and nature of the damage to diamonds at processing plant is largely determined by the design features of the equipment, the characteristics of the feed ore and the parameters of the ore disintegration process (change in the rotational speed of the autogenous mills, variations of the water supply to comminution process, choice of the optimum charge, etc.). To monitor the intactness of diamonds, an instrumental method using the X-ray tomography system and colored synthetic indicator diamonds was developed for identifying the process-related damage. The X-ray tomography system consists of a CT-Portable X-ray tomographic scanner, a crystal positioning device and customized software (developed by the Fraunhofer Institute and Aliud GmbH, Germany). The developed method enables improvement of the accuracy of the results, exclusion of the subjectivity of the mineralogical assessment, acceleration of data processing and promptly planning of the activities aimed at reducing the process-related damage to diamonds. KEYWORDS Diamonds, colored indicator diamonds, process-related damage, loss of mass, instrumental method, X-ray tomography system. INTRODUCTION Industrial tests of ore processing technology at the enterprises of ALROSA PJSC are accompanied by assessment of the process-related damage to diamonds. The assessment of the process-related damage to crystals is carried out for prompt elimination of factors contributing to the increase of impact forces in the process flow sheet of ore treatment plant. For this purpose a specially selected parcel of -4.0 + 2.0 mm sized natural indicator diamonds is used. The diamonds are exposed to ionizing radiation in order to turn them green and thus to create a distinctive feature. Colored natural indicator diamonds are described, photographed in several views and introduced into the process flow sheet of the processing plant, then extracted from the process flow, described and photographed again. The comparison of diamonds before and after their passing through the process flow sheet of the plant allows to find evidence of process-related impact on the crystal and to calculate the factor of process-related damage (the number of crystals damaged during liberation and recovery), the loss of crystal weight and the degree of damage to the crystals. The method of colored indicator diamonds is used to select processing methods, equipment or regime which would be the safest for diamonds based on the analysis of the factors of process-related damage. There are limitations of the method, such as:"

Jan 1, 2018

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By Tsuyoshi Hirajima, Hideyuki Okamoto, Himawan .. T. B. M. Petrus, Keiko Sasaki

"Flotation of arseno bearing minerals from their copper ore has been an interest due to the increasing awareness on protecting the environment by minimizing the possibility of exposed arsenic compound. Some approaches have been proposed, but the mechanisms of separations have not yet fully understood. In this study, oxidation using oxygen was applied. Instead of the complex copper ore flotation results, pure single mineral of tennantite and chalcopyrite foatability was conducted using Hallimond tube. Resembled with the flotation results of copper concentrate containing tennantite, the separation possessed the best result at alkaline condition (pH 11) at where the arsenic content was reduced from 3300 ppm to 1800 ppm. In order to be able to understand the mechanism of the separation atomic force microscope (AFM) was utilized. AFM images showed changes in morphology and behavior when minerals were treated in both acid and alkaline condition. It was found that the morphological change showed the reaction products representing the rate of reactivity of tennantite and chalcopyrite. From the measured force of adhesion, it can be observed that in alkaline condition the surface of both minerals is more hydrophilic than that in acidic condition possessing higher value. This is in accordance with the X-ray photoelectron spectroscopy (XPS) spectra in which hydroxide moieties occupied the mineral surface in alkaline condition while elemental sulfur is in acidic condition."

Jan 1, 2014

By Wenying Liu, Marek Pawlik

Long-chain ionic surfactants, with fatty acids and amines as the most important representatives, are widely used as collectors in froth flotation. These surfactants, generally referred to as weak electrolyte collectors, frequently form solid insoluble precipitates within a certain pH range. However, the action and behavior of these colloidal precipitates in froth flotation systems are not well understood and has not been well decoupled from those of dissolved forms. The objective of this study was to understand and compare the role of colloidal precipitates with that of the dissolved forms at gas-liquid and gas-liquid-solid interfaces. Using primary amine as the model surfactant, experiments were carried out to measure: the maximum volume of bubbles generated in the presence of dissolved and precipitated forms of the surfactant; surface tension for both forms of the surfactant using the drop shape and maximum bubble pressure methods; and contact angle using the sessile drop method. The experimental results showed that: in the presence of the precipitate, bubble volume was smaller, which was correlated with the lower surface tension and higher contact angle measured; the surface tension of solutions containing surfactant precipitate was affected by the surface age of liquid droplets. This study enhances understanding of the interfacial behavior of long-chain ionic surfactants under different conditions, which would help improve the efficiency of reagent utilization in froth flotation.

Jan 1, 2014

By P. M. Solozhenkin, V. P. Nebera, V. D. Skorohodov

"Aqueous dispersions of air specifically prepared on the basis of flotation reagent solution acquire active properties in relation to the solid surface and may be imply as a medium for flotation ores. Such aerated solutions were defined as Activated Aqueous Dispersions of Air (AADA) with 5-6:1 ratio and the procedure of mineral separation was defined as a flotation process under non-equilibrium conditions. These procedures differ from conventional flotation mainly in reagent interaction with minerals through their adsorption films on gas bubbles simultaneously forming flotation complexes. Gas-liquid mixture is kept till an adsorption layer of reagents close to the limit value is formed on the surface of bubbles. The theoretical basis of AADA is considered.The results of two-phase gas- liquid mixture (AADA) were studied. Two versions of AADA were considered. Electrical surface potential of the air bubbles with the surfactant film, untreated minerals particles in Coulomb attraction and flotation complex formation were analyzed. Special flotation machines were constructed for separation of mineral suspension in air dispersion, whose effectiveness was confirmed in flotation of apatite waste of Kovdor ore. FK-9 machine introduced on Kovdor iron ore combine for the recovery of apatite from current departures of factory. The froth product contained 7.2 % P2O5, with recovery of 44 % apatite, which was processed for getting melted phosphoric-magnesium fertilizers."

Jan 1, 2003

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure for the predictive simulation of flotation circuits far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, circuit survey and laboratory batch flotation data collected from an industrial flotation circuit are analysed. The data demonstrate that streams in an industrial flotation circuit exhibit varying particle floatability – concentrate streams typically float faster than tailing streams (Figure 1(a)). This floatability, however, is generally conserved around the various units within the flotation process (i.e. the effective floatability of the combined feed and product streams of a unit is equivalent (Figure 1(b)))."

Jan 1, 2003

By G. H. Li

Preparation strontium carbonate with celestite concentrate by flotation is studied by agglomeration-reduction roasting process. It is shown that, the drop strength of green pellet is greater than 4 times?(0.5m) -1 under the balling conditions of moisture of 9% and time of 18~20min. Lignin xanthate obviously improves the ballability of the celestite concentrate due to the increase of surface hydrophilicity, therefore, the balling rate is increased, as well as green ball strength. The drop strength of 7 times?(0.5m) -1 can be obtained when the lignin xanthate dosage is 0.5%~1%. Reduction roasting with anthracite shows that the SrSO4 conversion is 82%~83% for celestite concentrate pellet, under the optimal conditions of roasting temperature of 1100~1150? and time of 30min, and it is 10% higher than conversion of celestite lump under the same conditions. The strontium carbonate are prepared after roasted pellets are leached, purified and carbonated, and the SrCO3 content is higher than 97% , while the content of CaCO3 is less than 0.3%.

Jan 1, 2014

By Martin Rudolph

"Flotation is without a doubt one of the major processes for the separation of fine minerals and it has been applied for more than a century. A key task of a successful flotation separation is to find the proper chemical treatment to selectively hydrophobize and thus float a certain mineral phase using molecules or ions referred to as collectors, depressants, regulators and frothers. Commonly floatability is determined by microflotation tests using the Hallimond tube with pure mineral phases. This method however requires the pure mineral phase which is very often not even taken from the same deposit which is going to be processed. In this paper we present a new approach to in-situ determine and even map the floatability of finely disseminated mineral phases within cross-sections of an ore. It is based on measuring hydrophobic effects using colloidal probe atomic force microscopy with a hydrophobic polystyrene probe based on force spectroscopy with a lateral resolution of only a few nanometers. Coupled confocal Raman spectroscopy on the same locality enables the identification of the mineral phase. We present the working principles of the method and show which signals in the force spectra characteristic for hydrophobic interactions can be used to define floatability and which can then be mapped as single quantities, e.g. jump-into-contact events due to nanobubble occurrence or parameters of the long range interaction curves most probably due to capillary effects. A finely grained silicate ore containing the valuable rare earth mineral eudialyte from southern Sweden as well as pure samples of magnetite are presented as substrates to demonstrate the capability of this new approach. This method will not only help to find the proper flotation chemistry but it can furthermore help in researching and unravelling problems of floatability within similar mineral phases."

Jan 1, 2014

By S. Banisi, A. R. Ghasemi, M. Maleki-Moghaddam

Direct observation of the charge shape and its motion in industrial mills are not possible, it is then customary to use transparent end, small-scale mills (i.e., model mills) to determine the charge trajectory directly by visualization methods. Because of a short length of the model mills, the end-wall effects could introduce a significant bias on the observed charge trajectories and shape. The shorter the mill, the stronger the bias. This could be due to some material bridging between the end walls. In this research, the end-wall effects were investigated by gradually increasing the model mill length and analysing the charge trajectory and shape variation at a given operating conditions (i.e., ball filling, mill speed, liner type). The unbiased mill length was assumed to be beyond the mill length where no significant change observed in the charge trajectory and shape. For all tests, the torque of the charge was also measured by a torque sensor. The special design of the model mill with the diameter of 100 cm made possible to increase the mill length in steps of 3.6 cm up to 21.6 cm. Four types of liners, five steel ball fillings (10, 15, 20, 25, 30% v/v) and three mill speeds (55, 70, 85% of critical speed) were tested. The ball sizes ranged from 4 to 12 mm. The results indicated that when the mill length was below 10.8 cm the end walls prevented the charge from free falling. This resulted in lower impact point angles and lower power draws compared with the case of no end-wall effects. When the same experiments were performed using an iron ore instead of balls with the same size range, the impact of end-wall effects was more pronounced. For an increase of 30% in the speed (from 55 to 85%), the torque due the change in the charge shape decreased by 41% (from 3.7 to 2.2 kgf.m) when mill filling was 30%. At the same operating conditions when steel balls used the torque decreased only by 19% (from 9 to 7.2 kgf.m). This was expected due to irregular shapes of the ore particles which facilitated bridging. Three-dimensional DEM simulations also resulted in the similar conclusions.

Jan 1, 2014

By Klaus M. Hahn, Kurt Aasly, Jutta Lennartz, Hermann Wotruba, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Seafloor massive sulphide (SMS) deposits have been identified as important marine metal resources for the future. However, literature on mineral processing of SMS is currently limited, and to date, no research has been published on processing of SMS from either active or inactive hydrothermal vent fields on the Arctic Mid-Ocean Ridge. In this paper, individual SMS rock samples from the Loki’s Castle area were tested. Chalcopyrite, isocubanite and sphalerite represented the main copper and zinc bearing minerals in the SMS samples, whereas the gangue consisted of barite and silica. Based on the X-ray transmission response (XRT), i.e. differences in the atomic number of elements in tested samples, and using portable XRF (PXRF) values of elemental composition, individual particles were classified as a either product (low barium / high to low silicon / high copper and zinc) or waste (high barium / high silicon / low copper and zinc). The classification was based on the elemental composition of the samples with the cut-off grade equal to 0.5% for copper. It was shown that the XRT discrimination analysis correlated well with elemental (PXRF) data classification. The results clearly indicate that X-ray transmission sensor-based sorting can be used a useful technique for preconcentration of SMS rock samples. INTRODUCTION Due to different compositions of investigated samples, sensor-based sorting is a useful technique for preconcentration of different materials. The aim of using sensor-based sorting is to upgrade an ore by reducing the quantity of overall waste material reporting to the next processing stage. This can be achieved by eliminating (reducing) the waste fraction. By applying sensor-based sorting, the energy consumption for particle comminution as well as the required process water and reagents can be decreased. The total volume of the waste rejection leads to a proportional reduction in the total energy costs (Lessard et al., 2014, 2016)."

Jan 1, 2018

By V. Dementiev

Pyrite cinders is a complex raw material, in which the valuable metals are: Au(2.04 g/t), Ag(35.0 g/t), Cu(0.38%), Zn(1.1%) and Fe(56.0%). In this case high costs for mining and ore processing are not required. The hydrometallurgical treatment of pyrite cinders using thiourea, sulfite and cyanide solutions are examined in this paper. It was found that thiourea leaching is ineffective due to high consumption of thiourea and sulfuric acid. The cyanidation on pyrite cinders was conducted. Various options of the preparation of the products for the subsequent cyanidation have been examined. The tests on cyanidation process optimization were conducted. The effectiveness of these cementation methods by metallic iron or extraction for copper recovery from water phase has been shown. Zinc precipitation can be found in the form of carbonate. In order to recover noble metals from cyanide solutions, the cementation onto zinc dust was tested. The developed technology provides for recovery at 49-56%Au, 20-25%Ag, 22.5%Cu and 50%Zn during NaCN (1.4 kg/t) and CaO (6 kg/t) consumption. The results of pilot plant testing are the basis for technical regulations in order to design a pyrite cinders treatment plant. The technology has been examined in pilot-plant conditions. In this case the recovery of 54.5%Au, 45.3%Ag, 30%Cu and 49.9%Zn was achieved to provide saleable products. Keywords: pyrite cinders, thiourea leaching

Sep 1, 2012