Search Documents

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Sastry Putcha, Vamshi Vemula, Aneesh Goly, Kumar Allady

Current dynamic testing practice to obtain pile total capacity will not yield optimum capacity due to the strain incompatibility between the side and tip resistances during driving. Superposition of end of initial drive- static tip capacity and the peak static skin capacity during beginning of restrike and adding them is the preferred method. The FDOT method determines independent pile static tip and skin capacities in real time analyzing appropriate blows from the embedded tip and top data of the Embedded Data Collectors (EDC). This data is collected through a wireless radio transmitter, receiver, and laptop software. The approach utilizes EDC tip and top data and nonlinear single degree of freedom system to satisfy force and energy equilibrium with a global genetic inversion analysis. Top impacted energy equals at pile tip as sum of Static, Damping and Inertial energy providing independent tip resistance. With EDC sensors as boundary conditions, pile is divided into desired segments and using global inversion techniques one dimensional equation is solved for independent skin friction for every blow. EDC data compared close static load test results. The EDC - FDOT method has enabled cost effective 100% testing of driven piles cost effective. INTRODUCTION Historical documentation has shown that not only driven piles have a long history of usage but also continues to advance unceasingly till today. Historians placed the first pile driving using timber piles in the 4th century BC. While modern pile driving systematically started around nineteenth century, the credit for conceiving the idea of the applicability of wave equation to driven piles goes to David Victor Isaccs of Australia. His 1931publication “Concrete Pile Driving Formulae” provides the basis for modern pile driving using stress wave theory. He felt that the dynamic formulae then in use lacked the capability of detecting integrity and hence developed stress wave theory. This work was further developed starting in 1938 by W.H. Glanville and colleagues of British Building Research Board as they developed the first solution to the wave equation. But these early efforts have really taken off only with the advent of computers. E.A.L. Smith (1960) published ‘Pile Driving Analysis with the Wave Equation’ and provided first numerical solution to the wave equation. Within few years, the FHWA funded research and in due course this effort ushered the era of externally instrumented pile driving.

Jan 1, 2018

By D. Goossens

Quality control is a system which should guarantee that quality is achieved. It is the execution and verification of a project in an organised way, in order to obtain the maximum of certainty that the results meet the requirements. This concerns all stages of the project, from the soil investigation, over the design, to the execution. Quality control can and has been successfully realised for important projects by means of a quality plan. A quality plan is based on a number of general considerations, but should certainly be focussed on the particularities of a specific project. Practical examples of quality plans, which have been realised on sites in Belgium, are developed and the advantage of the system is shown by concrete case studies.

Jan 1, 1996

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By Donald A. Bruce

The construction of major structures in karstic limestone terrains poses difficult problems to designer and contractor alike. This reflects the inherent variability of such conditions, and also the significant impacts caused by the construction processes themselves. Three case histories are provided of recent projects in the United States: the sealing of a major inflow into a quarry, the improvement of a highly loaded bridge pier foundation, and the installation of high capacity micropiles. Emphasis is placed on problem assessment and execution verification.

Jan 1, 2002

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By Janne P. Isohaka, Anssi M. Laaksonen

"Abstract In Scandinavia the use of steel pipe piles in bridge foundations started in the mid-1980s and has increased steadily since. As the piles driven in soft soils are slender, they can fail by buckling. Buckling usually requires taking into account the second order effect in structural and geotechnical design.The purpose of this paper is to derive formulas for demonstrating the theory behind the formulas given in literature for the second order effect of initially bent piles.IntroductionIn Scandinavian countries solid bedrock usually lies at moderate depth. If the bridge site is in an area where the soil above the bedrock is soft, the bridge is usually founded on end-bearing piles resting on the bedrock.The main purpose of the piles is to transfer axial forces into bearing soil. Like columns, piles can lose their stability by buckling when surrounded by soft soil. When axial compression on a slender, initially straight, pile reaches a particular value called the critical load, the pile is subjected to lateral deflection and loses stability. The soil around the pile suffers a corresponding deformation. This soilstructure interaction increases the critical load compared to a pile without surrounding soil.It is very unlikely that piles are ideally straight. Initial curvature along with curvature and deviation caused by the installation of piles causes bending moments to the pile when normal force is applied. These lateral displacements increase when normal force increases. This increase of moment is called asecond order effect.Eurocode and literatureEurocode 7 includes guidelines for the design of piles (Eurocode 3, section 5 includes design of steel piles). However, there are no clear guidelines for considering the second order effects related to piles surrounded by soil. Eurocodes advise doing structural design of piles the same way as in the case of columns. With columns, the second order effect is taken into consideration by multiplying the first order moment with the factor shown below (SFS EN-1992-1-1, 2005):"

Jan 1, 2014

By Christian Besson

This article describes the implementation of a new jointing process for use between diaphragm wall panels. This process was initially introduced on the SOCATOP work site in uburban Paris (which involved the closing of the western section of the A86 bypass road), on a tunnel ventilation shaft. This brand new system upgrades the potential offered by other types of joints available and enables both ensuring the continuity of panels for structures over 40 m in depth under the strictest safety conditions and constructing shafts with diameters of less than 15 m. A patent for this process has recently been filed.

Jan 1, 2002

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By Dan A. Brown

This paper describes a method of conducting rapid lateral loading tests of deep foundations in which the load is applied to the foundation with a time duration of less than one second. For purposes of this paper the loading is applied using a pyrotechnic loading system commonly referred to as Statnamic. However, the method should apply to any lateral loading system which produces a force time history with a loading duration of 20 msec to 1 second. The test provides a measure of the dynamic and static response of the soil/foundation system and must be evaluated as a dynamic loading. Interpretation of the test includes a simple single degree of freedom (SDOF) model which can account for the inertial effects of foundation mass, system damping, and static foundation stiffness. The results of the test measurements are compared with four case histories in which comparative static load test data are available, including pile group foundations and large diameter drilled shaft foundations.

Jan 1, 2007

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By Thomas M. Gurtowski

This paper presents a summary of allowable bearing pressures and skin friction values that have been used to design drilled pier foundations for support of high-rise structures in downtown Seattle, Washington. These design parameters are based upon a review of geotechnical reports and records of more than 20 building projects. The following pages present a description of the soils encountered at these sites including foundation bearings soils, and design bearing and friction values. The accumulated data is summarized in Table 1, and the locations of the buildings are shown in Figure 1. A detailed description of the construction of two belled drilled piers are presented illustrating typical methods and procedures used in downtown Seattle. The two cases are from the Washington State Convention and Trade Center (WSC&TC). SEATTLE AREA SOILS The Puget Sound area was subjected to several major glaciations during the Pleistocene Epoch. Glacial ice originated in the cordilleran and coastal mountains and the Vancouver Range of British Columbia. The maximum southward advance of ice reached the area about halfway between Olympia and Centralia. As a result of these glaciations, the Puget Lowland was filled to significant depths by glacial and non-glacial sediments during the Pleistocene.

Jan 1, 1990

By Juan J. Campo

The Freeport-McMoRan Main Pass Mine development in the Gulf of Mexico is a complex designed to extract up to 67 million long tons of sulphur over a 40 year period. The initial development includes 15 platforms and 13 bridges located in water depths ranging from 208 to 214 feet, approximately 15 miles east of the Mississippi River Delta. Three additional platforms were designed and installed for the oil and gas development in the complex. Over 110, 000 short tons of steel were required to fabricate the structures. As the sulphur is extracted significant subsidence is predicted over a major portion of complex in the shape of a very large bowl. Vertical elevations are predicted to change as much as 65 feet. Horizontal movements and mudline slope changes cause adjacent platform decks to move as much as 30 feet relative to each other. Differential soil movement is predicted between piling of individual platforms causing the piling to spread, resulting in significant lateral loading on the piling. Relative vertical soil movements are predicted along the lengths of the piles which causes "up drag" or "down drag" forces on individual piles. This paper addresses the design of the piling for the structures in the complex. Design criteria will be discussed explaining how the more traditional offshore environmental and gravity loadings were combined with the unique loading caused by subsidence. Design and analysis procedures will be explained and analysis results presented. These results include the incorporation of 100 ksi steel in thicknesses up to 5 inches in some of the tubular piles. Comparisons will be made between conventional offshore structures and these structures designed to accommodate the subsidence.

Jan 1, 1992

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By Sam Yao, Ali Naeem, Sara Barrett

Brooklyn Basin Project is a multi-billion-dollar development of the former Port of Oakland 9th Avenue Terminal located along the Oakland Estuary of California. A centerpiece of the development is the 10-acre shoreline park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. Prior to constructing the wharf, a rock dike was placed to protect the shoreline. The presence of the rock dike increased the hazards from lateral spreading of the underlying bay mud and non-ductile shear failure of piles driven through the dike. To open the park to the public, the wharf required a seismic retrofit in compliance with the California Building Code. The paper presents the results and conclusions of the following topics: • Structural condition assessment and repair strategies for the existing wharf deck, piles and jackets • Application of the California Building Code (CBC Ch31F) for the performance-based seismic evaluation of existing piers and wharves • Nonlinear pushover analysis of the wharf including the combination of inertial and kinematic effects • Impact of rock dike on lateral spreading and kinematic effects and the significance of existing piles in stabilizing the lateral spreading of the rock dike • Retrofit strategies for the wharf to meet the required seismic performance requirements per the California Building Code and reduce the demands on existing piles which were driven through the rock dike INTRODUCTION The 65-acre Brooklyn Basin Development project is located in Oakland, California. The project consists of 3,100 housing units, 200,000 sq. ft of retail and commercial space, along with various parks and public access improvements along the Oakland Estuary. A centerpiece of the development is the 10-acre Shoreline Park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. As shown in Figure 1, the wharf deck and piles support the 9th Avenue Terminal Building.

Jan 1, 2018

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By W. H. Liu

The stability of floors of large drydocks and wagon tipper sheds at coal terminals is an important matter but quite difficult to solve. Anchors can be used to join floors to foundations thus ensuring the stability of floors by the self-weight of floors and the pull of anchors. In this paper, the author describes the structures and types of the anchors used in the floors of the drydock in Beihai Shipyard and the wagon tipper shed at Shijiu Port, both in Shandong Province China, the determination of bearing capacity of anchors in rock bed of highly weathered granite, the comparison between prestressed anchors and non-prestressed anchors, the construction technology of anchors and the analysis of field experimental data.

Jan 1, 2010