Search Documents

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By Roy Peratrovich

An innovative cost-saving design for a 1,100 ft bulkhead on the Tanana River at Nenana in central Alaska won Alaska Construction & Oil magazine's Construction Achievement Award. The designers utilized materials available nearby at low cost. They planned sheet pile enclosures, self-anchored back into shore without cell closures. They made it practical for inexperienced local workers to do the building. And they completed the project on time and below a reduced budget.

Jan 1, 1985

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By Austin Metz, Kevin Stanton, Ramin Motamed

"A recent study calibrated Load and Resistance Factor Design (LRFD) resistance factors for local soil conditions in the Las Vegas Valley. As a part of this calibration, an extensive database of drilled shaft load tests and associated subsurface soil information were collected and compiled. This database, deemed the Nevada Department of Transportation Deep Foundation Load Test Database or NDFLTD, was designed with the presentation of load test data, the subsurface soil conditions, and the spatial distribution of the data in mind. In addition, the NDFLTD was developed in a way that allows additional data to be added as it becomes available. As such, the rules of database normalization were followed to allow for additional and different types of data to be added to the database and reports. Microsoft Access was chosen to present the data because it is easily accessible to anyone with Microsoft office software, it has a quick learning curve, and it has the ability to present a relational database. The largest obstacle faced when creating the NDFLTD was normalizing the data used in the LRFD calibration, with the goal of reaching the 5th normal form.INTRODUCTIONLRFD is based on statistical performance of engineering components, as opposed to the more traditional Allowable Strength Design (ASD), which divides the strength of a component by a safety factor. Calibration of resistance factors for LRFD requires a robust statistical analysis of past performance. For drilled shafts this requires a database of full scale load tests (Abu-Hejleh et al. 2014). The FHWA developed the largest US based deep foundation load test database, deemed the DFLTD, collecting data from 1985 to 2003 when funds ran out (Abu-Hejleh et al. 2014). Recently, the DFLTD has been updated to modern standards (Petek et al. 2016). In October of 2007, the FHWA mandated state department of transportations (DOTs) to follow AAHSTO LRFD guidelines for their highway foundation designs (Abu-Hejleh et al. 2014). Since then multiple state DOTs have developed their own, region specific deep foundation load test databases. Florida has a long history of developing databases for deep foundation LRFD resistance factor calibration, with the two main databases being the FL database, and The Deep Foundations Database (Abu-Hejleh et al. 2014). Iowa developed a Microsoft Access based database in 2014 (Garder et al. 2014). Oregon developed a database compiling pertinent data from the DFLTD, Florida DOT’s Deep Foundation Database, as well as from other databases (Smith et al. 2011). Illinois developed the “International Database” for static and dynamic reliability based calibration (Long et al. 2009). Louisiana developed a database for LRFD Calibration of driven piles in 2009 (Abu-Farsakh et al. 2009). The California Department of Transportation has its own internal foundation database, which is housed within the Foundation Testing Branch archive (Smith et al. 2011). In 2016, the Nevada Department of Transportation (NDOT) presented its own LRFD calibration for the Las Vegas Valley (Stanton et al. 2017), and the NDFLTD was developed as a part of that project (Motamed et al. 2016)."

Jan 1, 2017

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

By Patrick E. Durnal

The Richmond-San Rafael Bridge was built in the early 50s' and was first opened to traffic on August 31, 1956. Among California's longest steel bridges, it spans more than 21,000 feet across the northern portion of San Francisco Bay. It is one of six toll bridges currently undergoing seismic retrofit in the Bay area. Current retrofit criteria require the structure not to collapse in a Magnitude 8.3 earthquake lasting 45 seconds on the San Andreas Fault. The earthquake epicenter is 10 miles to the west of the Bridge, near the mouth of San Francisco Bay. Another major fault is the Hayward Fault, with a potential of a 7.5 magnitude earthquake. It is only 4 miles east of the eastern end of the bridge. The retrofit criterion is that the structure survives these earthquakes without collapse or loss of life, and that they are capable of repair within a period of one year. Therefore an energy absorbing, ductility and nominal resistance based approach to the retrofit design have been adopted for the retrofit of this bridge. Foundation Retrofit The foundation retrofits were designed to satisfy of drift criteria of 6 inches at the base of the footings, and to keep the existing H-piles from experiencing unacceptable levels of permanent soil displacement and /or structural rupture. Full-scale structural lateral load testing of BP14x89 piling, to rupture, has helped to determine the drift criteria. However recent non-linear analytical results, have led to a redesign, which may allow for 12 inches of drift. The as-built analysis of the Micropile piers determined that those piers would not exceed the 6-inch drift criteria so lateral resisting shear piles were not needed at those piers.

Jan 1, 1998

By Tobias Hansson

The quality of Lime Cement (L/C) columns is to a great extent dependent on the installation procedure. At a site in the south of Sweden, the client reported problems with the installed columns. To evaluate the operator and equipment dependent part of the installation, Hercules Grundläggning AB was appointed as a competitor to the site contractor. The purpose was to install a number of L/C columns with equal installation parameters for both contractors. A total of 65 test columns were installed in June 1999. The geology is a typical Swedish organic soil profile with a top layer of peat overlying gyttja and clay. Two different binders were used in the comparison; blast furnace slag with cement and lime with cement. After installation, the quality of the columns was monitored by penetration tests and a column sampler for extracting whole columns. The column penetration test were performed 28 and 134 days after installation and extraction 134 days after installation. Inspection and tests of the extracted columns showed that by using a fully computer controlled procedure, the contractor produces columns of superior quality and homogeneity.

Jan 1, 2000

By Tianfei Liao

Extensive site investigations revealed that abandoned shallow mine workings exist under a site planned for construction of a major new facility. Since the mine voids were susceptible to collapse, they were stabilized by grouting. After completion of the mine remediation, three types of deep foundations (micro-piles, auger-cast piles, and drilled piers) were considered for this site. Micro-piles spread the load via the bond between the pile and the bedrock. Without significant length socketed in rock, the axial load of auger-cast piles and drilled piers has to be concentrated on end bearing. Although spreading the load is preferable in this environment, economic consideration dictated the choice of drilled piers for construction.

Jan 1, 2009

By Magnus Ruin

The dry deep mixing method for stabilization of soft soil has been used in the Scandinavian countries for 25 years. The typical application has been stabilization of soft inorganic clay. Today the method is used more frequently in organic soil with good results. The Limix System, introduced in the USA by Hercules Grundläggning AB and TREVIICOS Corporation, is a cost-effective dry deep mixing method used to stabilize most types of soft soil. This paper presents the general principles of stabilizing organic soil with the dry mix method and two case histories of soil stabilization projects in organic soil. Between October 2000 and June 2001 the Limix System was used in England to stabilize soft organic alluvium at the Channel Tunnel Rail Link, Contract 440. During year 2000 the Limix System was used in soft organic soil in Holland near the Groene Hart Tunnel entrance to support trench excavations for slurry walls and concrete barrettes.

Jan 1, 2001

By Mark R. Svinkin

Construction vibrations may adversely affect surrounding buildings and their effects range from human discomfort and disturbance of sensitive devices to visible structural damage. There is no unique conclusion regarding the effect of construction vibrations at every site. Measurement is usually made to monitor vibrations and control them with the vibration thresholds for disturbance of sensitive objects as well as damage to structures. To prevent potential litigation and mitigate the vibration effects on sensitive devices, people and structures, it is necessary to manage and minimize vibration problems before the beginning of construction activities or installation of vibrating machine foundations, and during construction. Pre-construction damage survey and engineering vibration investigations, including the prediction of anticipating vibrations, have to be made at most construction sites in advance of construction activities. Vibration monitoring and control have to be provided during construction. The instrumentation feedback of vibration prediction, monitoring and control provide the basis for choice of measures to prevent or mitigate vibration problems and settlement damage hazards.

Jan 1, 2002

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

By John S. McCartney, Ismaail Ghaaowd

This study presents the results from centrifuge modeling experiments performed to understand the effects of temperature changes on the pullout capacity of scale-model energy piles embedded in normally- consolidated clay layers. The energy pile under investigation is an aluminum cylinder instrumented with internal strain gages and thermocouples, and its temperature is controlled using an internal electrical resistance heater. The energy pile was first heated until the temperature, pore water pressure, and volume change of the surrounding clay layer stabilized, after which the energy pile was cooled. Pullout tests were then performed on the energy piles heated to different temperatures to understand the effects of the preceding heating-cooling cycle on the pullout capacity. In addition, the clay undrained shear strength profiles were measured using push-pull T-bar penetration tests before and after heating. INTRODUCTION When a heat source such as an energy pile is embedded in a saturated clay layer, temperature changes will result in changes in pore water pressure as the rate of heating is typically faster than the rate of pore water drainage (Campanella & Mitchell 1968, Abuel-Naga et al. 2007, and Ghaaowd et al. 2016). Although all soils will initially expand during undrained heating, normally consolidated soils typically exhibit permanent contraction while overconsolidated soils exhibit expansion after sustained heating when drainage is allowed (Vega & McCartney 2015). Subsequent drained cooling typically leads to elastic contraction. Thermally- induced changes in pore water pressure and volume during transient heating and cooling may affect the soil- structure interaction of energy piles, as well as the ultimate capacity of the energy pile. This study is relevant as relatively few studies have been performed on the behavior of energy piles in soft clay (e.g., Ng et al. 2014), with most focused on the behavior of drilled shaft energy piles in stiff rock or overconsolidated clays (e.g., Laloui et al. 2006; Murphy et al. 2015; Wang et al. 2015; McCartney and Murphy 2017).

Jan 1, 2018

By Loring A. Wyllie

Preparation, understanding and use of soils reports must be a team effort to be fully effective. The soils engineer must know what is to be built and exactly where. The structural engineer and owner must be fully informed on the foundation problems of the site. There must be frequent team review of information obtained from subsurface investigation and of design as details develop. The soils engineer should be available on a continuing team basis as design proceeds and should be directly involved with inspection and interpretation of site conditions as construction continues.

Jan 1, 1986

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

By Andreas Brandner

"At the beginning of 2007 the Austrian contractor PORR was awarded with remediation works for a 48-km long part of the railway line from Campina to Predeal – part of the Trans European main Corridors TEN-T priority line 22 Bucurest – Brasov, connecting the southeast European countries with the heart of Europe.Due to partly new realignment and change of regular sections as well as protection against rockfall and slope slide a huge bunch of slope stabilization works became necessary, which were awarded to the contractor PORR and their designer IB-Brandner.Following the studies of the tender documents for the planned protection measures responsible managers of PORR decided to propose an alternative protection design by IB- Brandner. Changing the original design a more flexible and environmentally compatible solution consisting of high performance net, soil nailing and rockfall protection systems (fences) was elaborated and adapted to local needs. During design process, several critical areas were identified and additionally taken into account.In the paper examples of the design and erection process show how difficulties in implementation starting with the presentation of the idea continuing to the realization on site were managed and a technically more sophisticated and commercially competitive solution could be delivered to the customer Romanian Railway – case study.The European Commission awarded – following an election process in which all citizens of the EU could join - the remediation project Railway line Campina – Predeal in Romania as the environmentally best EU co-financed infrastructure project. GENERAL PROJECT EVALUATIONDue to original design slope stabilization should be done by concrete slabs fixed with prestressed anchors and shotcrete cover.The area to be secured was limited to a 12-meter strip left and right from the railway track without reference to nature and local needs. Discussions with the client and his designer and rising awareness for the hazards to address took several months. Site visits in Austria to provide insight in the problems of dealing with natural hazards helped to convince the client of the needs and our alternative design."

Jan 1, 2017

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By Basem Sh. Hazzan

In the last four decades significant effort has been devoted to designing piles in expansive clay soils. Nevertheless, only a scant effort has been devoted to the elimination of heave forces acting on the upper part of lightly loaded piles. For this purpose, an investigation site was established in Karmiel in Northern Israel. On this site sixteen unloaded cast-in-situ piles, both uncoated and coated, were installed in a moderately expansive clay soil in the end of summer 1996. The piles were executed to different depths ranging between 2m and 7m and were observed over a period of 27 months. Another nine unloaded cast-in-situ bored piles were installed at the end of summer 1998 for carrying out pullout tests. These piles were embedded two meters from the ground surface. Results obtained from observations and from full-scale static pull out tests showed that separating the piles from the surrounding clay in the active zone by a twin walled sleeve eliminated the heave forces significantly. The scope of the work is, determining of the elimination degree of the heave forces due to the provision of the above sleeve.

Jan 1, 1999

By Aly M. Mohammad

The 12th and 14th Street Viaducts, which carry Route 139, are located west of the Holland Tunnel in Jersey City, New Jersey. The two viaducts, provide access to and from the Holland Tunnel (which connects New York City and New Jersey) and carry upwards of 50,0000 vehicles per day from Jersey City and New York City to points west. The New Jersey Department of Transportation (NJDOT) selected AECOM to perform design services including rehabilitation and seismic retrofit for the 12th Street and 14th Street Viaducts while maintaining traffic at all times. Building a new parallel bridge just north of the 14th Street Viaduct was essential in avoiding extremely costly traffic delays. Installation of the new foundation, in close proximity to the existing viaduct, required drilling through some of the existing timber piles supporting the bridge. As a result, the existing bridge was required to be reanalyzed for this new foundation configuration. This proposed structure consisted of 8 piers each supported on a single six (6) foot diameter drilled shaft. Currently this portion of the bridge structure has been constructed. The shafts were constructed with rock sockets that were five feet six inches (5?- 6??) in diameter and were extended 11.2 feet (3.4 meters) into rock. A 2300 ton Osterberg Load Test was performed on one production shaft to confirm the capacity of the shaft. The rock socket for the test shaft was in sandstone. This paper will present a description of the design methodology and construction methods adopted for the foundations. In addition, the paper will illustrate the Osterberg Load Test including: equipment used, number and locations of strain gages, and interpretation of results. Additionally, regarding the close proximity of the new foundation, the paper will present the type of equipment used to drill through the existing timber pile foundation while minimizing the impact on the integrity of the existing foundation. We will also present the method of analysis for analyzing the redistribution of load on the remaining piles. The results presented in this paper will assist the design engineer by providing a comparison between the geotechnical design assumptions and the actual measurements obtained by field measurements for this rock formation.

Jan 1, 2009