Search Documents

By Dan Brown

This paper provides an overview of the advantages and limitations of continuous flight auger (CFA) and drilled displacement (DD) systems compared to other deep foundation systems, along with a summary of important considerations for selection and design. Geotechnical and project considerations are described which favor the use of CFA and DD piling, and also which may be problematic for this type of construction or which may limit the practicality and competitive advantages. A brief summary of design methods for axial and lateral loading is included.

Jan 1, 2005

By George J. Tamaro

In 1967 the Port Authority of New York and New Jersey undertook the construction of the World Trade Center (WTC) diaphragm walls, installation of the lateral support system and the excavation of the site, commonly referred to as the "Bathtub". The work took two years to complete. In 2001 the City of New York undertook the re-excavation of the site after the terrorist attacks. The recovery work will take eight months to complete. This paper describes the initial work on the WTC "bathtub" in the late 1960s and the recent work during the recovery.

Jan 1, 2002

By Frederick C. Rhyner

The United States government sponsored the construction of a new vehicular bridge over the Diyala River in Bubriz, Iraq. This paper describes the geotechnical engineering for design and construction of drilled shaft foundations for this bridge. An Iraqi geotechnical engineering firm made borings and laboratory tests while analysis and design recommendations were provided in the United States. Despite the severe challenges of engineering in a war zone, excellent cooperation was the key to a successful effort. Three drilled shafts designs were necessary to accommodate the different subsurface conditions: a) medium-compact to compact sands, b) stiff to hard clays and c) mixed soil profile. The alpha and beta methods were used to estimate capacities for a conservative design, recognizing that quality control during construction might be less than what is normally provided in the United States. Iraq has a high seismic risk and LPILE was used to estimate the drilled shaft response during earthquake loading conditions. Settlement estimates were made using FHWA methods. Construction was carried out entirely by local Iraqi firms, despite the challenges of working in an active conflict area.

Jan 1, 2009

By Ernest Naesgaard

Post-grouted micro-piles were used for the seismic upgrading of the Vancouver International Airport Domestic Terminal Building (DTB). The micro-piles provided vertical resistance to both uplift and compression loads to supplement the existing timber pile foundations ability to resist the earthquake induced forces, and to provide foundation support at locations where the installation of traditional driven piles was difficult. This paper describes the site conditions, design rationale, installation method and quality control testing procedures. Site and Subsurface Conditions Vancouver International Airport is located within the central portion of Sea Island, Richmond, British Columbia (Fig. 1). Sea Island is bordered by branches of the Fraser River on the northeast and south sides and the Strait of Georgia along the west side. The natural grade of the island is part of a large delta that has been built up over several thousand years. The general pattern of sediment deposition has followed the direction of the Fraser River flow from east to west, and has built up soft sediments of about 200 m thickness at Sea Island (Luternauer, et al. 1993, Mathews and Shepard 1962). The original grade in 1962 prior to the existing Airport Terminal Building development was at about geodetic elevation 1.1 m with a grass and topsoil cover.

Jan 1, 2004

By Julie Hampden, Tim Dardis, Per Reinhall

"Noise from impact pile driving can harm fish, marine mammals and other sensitive wildlife over large areas. Marine pile driving is highly regulated, and regulators require sound levels to be below certain thresholds to avoid harassment and injury to sensitive marine life. In many locations, timing restrictions, use of noise attenuation technologies and extensive monitoring for impacts to wildlife are also required. As a result, permitting can be laborious and time consuming, and project implementation and scheduling can be complicated. Underwater noise levels are measured with an underwater microphone (hydrophone), which converts noise pressure to voltage and is calibrated to express the noise pressure in Pascals (Pa). The pressure is often expressed using a logarithmic scale, in decibels (dB). Several specific metrics can be used to describe underwater noise. Three common metrics are the instantaneous peak sound pressure level (dBpeak), the root mean square pressure level (dBRMS) and the sound exposure level (dBSEL) referred to as the peak, RMS and SEL levels, respectively.During impact pile driving, the peak pressure represents the instantaneous maximum pressure, either overpressure or underpressure, observed during each pile strike. The RMS level is the square root of the mean of the square of the pressure during the duration of the impulse; it is the average pressure level of the pile strike from beginning to end. The cumulative SEL (SELcum) is calculated by summing the cumulative pressure squared and integrating over time of duration of the pile strike. SEL is used as an indication of the cumulative energy of a pile driving event, which may consist of one or many pile strikes.Regulatory agencies use these metrics to help characterize the noise pressure levels that can affect sensitive species. Some of the most frequently encountered biological thresholds in the Northwestern United States that are used by regulators to describe potential impacts to sensitive species are summarized in the following table. Agencies have defined thresholds for different types of injury, either hearing or bodily harm, and for temporary injury or disturbance."

Jan 1, 2017

By Andrew Moran, William H. Walton, Matthew D. Emrick, Mary C. Nodine

"A rapidly growing company in the northern US needed a large auditorium built into a dolomite bedrock hillside. The structure required an 80-foot-deep earth retention system independent of the auditorium foundation and superstructure. Allowable wall movements were limited to less than two inches. A 60-foot-tall permanent shotcreted soil and rock nail wall was designed for excavation support. The soil and rock nail wall utilized both active (post-tensioned) and passive nails, with capacities and installation angles optimized to address varying soil and rock conditions and to support heavy surcharges. The wall was configured with three two-foot-wide benches to facilitate controlled blasting and removal of more than two million cubic yards of soil, limestone and dolomite bedrock, and featured a permanent cast-in-place concrete face and a robust waterproofing and drainage system. A 20-foot-high reinforced concrete retaining wall was required at the top of the soil and rock nail wall to raise grades, resulting in a large surcharge.Design of the soil and rock nail wall was initiated less than three months before the start of construction, requiring expedited geotechnical explorations, analyses, design, and construction that would occur simultaneously. Design changes were made to address the discovery of a weak clay residuum seam at depth running along the base of the excavation, as well as significant changes to the building footprint made after the start of construction. Extensive performance monitoring was conducted during construction to measure vibrations and movements.Introduction and Project BackgroundA fast-growing company in the northern United States had a need for 600,000 square foot, 11,000 seat auditorium as part of its campus expansion. The auditorium was built underground, into a hillside to preserve the views of rolling terrain and farmland beyond. It featured a green roof and rockwork facing that mimicked regional geologic formations. The sixstory building required up to 80 feet of earth retention, including 60 feet of excavation beneath existing grades.As concepts for the project evolved, it became apparent that due to the geologic conditions, space limitations on site and the depth of cut required, a standard counterfort wall system would not be feasible. With groundbreaking for the building three months away, Thornton Tomasetti (structural engineer) engaged GEI Consultants, Inc. (wall design engineer) to design a 1,600-foot-long permanent soil and rock nail wall to support the excavation. The wall design engineer implemented a geotechnical exploration program immediately and began the design process, coordinating closely with Nicholson Construction (specialty"

Jan 1, 2017

By Peter de Kort

Tunnels in urban areas generally require deep excavations in soils under the groundwater table. In The Netherlands uplift loads are generally taken by piles installed into dense sand layers, which are hard to penetrate. To avoid nuisance and damage to the environment, piles often need to be installed using vibration free methods, which also have the advantage of low noise levels during installation. Drilling piles and obtaining a high uplift resistance is a contradiction in itself. Franki has adopted several installation methods based on the injection of grout during drilling and/or post grouting to overcome the difficulty of hard layers. This report presents two projects, situated in Rotterdam and Sneek, where vertical tension piles in floors, subject to high uplift loads, have been used. It also explores a project in Zeebrugge (Belgium), where tension piles are installed at an inclination of 1:1 to anchor a diaphragm wall for a quay construction. Test results presented in this report show, that vibration free and soil displacing piles can be installed in very dense sand layers and that a high uplift resistance can be achieved. It is also shown, that a variety of installation methods is available, even in limited space.

Jan 1, 2008

By Edmund J. Cardoza

The Detroit Water and Sewerage Department (DWSD) provides water and wastewater services to the Greater Detroit Metropolitan Area. Sewerage is treated at the DWSD Wastewater Treatment Plant (WWTP) located at 9300 W. Jefferson Street south of the City of Detroit, Figure 1. PARTICIPANTS Engineering and design of the project for the DWSD was performed by Harza Engineering Company, Inc., C.C. Johnson & Malhotra, P.C. and their sub-consultants, including Worley Engineering and Wade Trim. The Prime Contractor is a Joint Venture of Traylor Brothers, Inc. and Jay Dee Construction. The shaft drilling and riser installation was performed by The Millgard Corporation in joint venture with the Prime Contractor (MTJD). The selection of specialized drilling equipment and the supervision and performance of the access shaft and riser installations was primarily the responsibility of The Millgard Corporation (TMC).

Jan 1, 2001

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By John D. Thornley

Alaskan villages typically store a one-year supply of fuel to reduce significant delivery costs. Alaska Village Electric Cooperative (AVEC), an electric utility cooperative providing power to 51 Alaska villages, has made a concerted effort to upgrade and improve their undersized and aging facilities. The Village of Stebbins, located south of Nome on Norton Sound is receiving upgrades to its AVEC bulk fuel facilities. Stebbins offered unique challenges from a foundations perspective due to the nature of the soil. The geotechnical investigation found the soil below roughly a third of the footprint of the bulk fuel facility to be thawed with seasonal freezing and the remainder was found to be warm permafrost with ground temperatures of between 30°F and 32°F. This is a unique and challenging arctic engineering design issue because foundations are designed differently for frozen ground conditions. Driven piles were selected because of site constraints, such as the design flood elevation and the change from thawed to frozen ground conditions. The pile design specified that the pile embedment depths would be selected based on the results of pile driving analyzer (PDA) testing during construction in the thawed ground and maintained within the frozen ground portion of the footprint. Difficulties during pile driving in the frozen ground resulted in several piles becoming severely damaged, requiring subsequent removal. This resulted in a reevaluation of the means and methods for pile installation. Additional fieldwork was performed to further characterize the subsurface soils and their frozen nature. Options for installation of piles in difficult areas were evaluated including ground thawing, predrilling, and reducing embedment depths. Presented within this paper are the findings from the initial and subsequent field explorations, discussion of the design methodology, and the decisions that led to successful installation of piles at this challenging remote village.

Jan 1, 2017

By John D. Thornley

Alaskan villages typically store a one-year supply of fuel to reduce significant delivery costs. Alaska Village Electric Cooperative (AVEC), an electric utility cooperative providing power to 51 Alaska villages, has made a concerted effort to upgrade and improve their undersized and aging facilities. The Village of Stebbins, located south of Nome on Norton Sound is receiving upgrades to its AVEC bulk fuel facilities. Stebbins offered unique challenges from a foundations perspective due to the nature of the soil. The geotechnical investigation found the soil below roughly a third of the footprint of the bulk fuel facility to be thawed with seasonal freezing and the remainder was found to be warm permafrost with ground temperatures of between 30°F and 32°F. This is a unique and challenging arctic engineering design issue because foundations are designed differently for frozen ground conditions. Driven piles were selected because of site constraints, such as the design flood elevation and the change from thawed to frozen ground conditions. The pile design specified that the pile embedment depths would be selected based on the results of pile driving analyzer (PDA) testing during construction in the thawed ground and maintained within the frozen ground portion of the footprint. Difficulties during pile driving in the frozen ground resulted in several piles becoming severely damaged, requiring subsequent removal. This resulted in a reevaluation of the means and methods for pile installation. Additional fieldwork was performed to further characterize the subsurface soils and their frozen nature. Options for installation of piles in difficult areas were evaluated including ground thawing, predrilling, and reducing embedment depths. Presented within this paper are the findings from the initial and subsequent field explorations, discussion of the design methodology, and the decisions that led to successful installation of piles at this challenging remote village.

By Adel M. Hanna, Ibrahim M. Mashhour

"Collapsible soil is known as one of the difficult soils, which possesses considerable strength when it is dry and significantly reduced when inundated. In practice, in case of a thick layer, pile foundations are often used to penetrate the collapsible soil to firm soil/rock strata. Inundation of collapsible soil is accompanied by a large and sudden settlement, which may significantly increase the negative skin friction and accordingly the drag loads on the pile’s shaft. Inundation may take place from the running surface-water or raising the groundwater. In case of surface water, the amount of settlement varies, depending on the extent of the wetted zone and the degree of saturation in the soil, while rising groundwater will produce full saturation in the ground and accordingly larger settlement.In the literature, there is lack of reports dealing with the prediction of the drag load on piles in collapsible soils subjected to inundation. This is due to the complexity of modeling collapsible soil analytically. Alternatively; the results of a sophisticated experimental investigation may guide the researcher to develop a model to predict the drag load on these piles.This paper presents the results of a small-scale experimental investigation tailored to measure the soil collapse during inundation and the associated drag load on an endbearing pile’s shaft. Based on the results of the present investigation, the effect of the soil collapse potential and the pressure acting on the soil during inundation on negative skin friction is presented.INTRODUCTIONCollapsible soil is a metastable material, traditionally defined as unsaturated soils that experiences a radical rearrangement of particles and significant reduction of volume upon wetting with or without loading (Bara 1976; Houston et al., 1988). A wide range of soils fall into the category of collapsible soil, including naturally existing types of soils such as: Alluvial flood plains, mud flows, residual soils, colluvial deposits, fans, aeolian or wind-blow deposits sands and silts (loess), volcanic tuffs, gypsum, dispersive clays, loose cemented sands , sodium rich montmorillonite clays (Clemence and Finbarr 1981).Soil wetting and soil saturation may take place as a result of urbanization or natural causes, such as: groundwater level rise, landscape irrigation, broken water pipelines or sewer lines, poor surface drainage, groundwater recharge, cut/fill construction, and moisture increase due to capillary rise. The severity of the outcome depends heavily on the so called collapse potential of the soil, which depends mainly on; soil type, compaction effort, initial water content and stress level at soaking (Houston and Houston, 1997; Ayadat and Hanna, 2007)."

Jan 1, 2015

By Richard Shea

Morris-Shea, an Alabama-based deep foundation contractor, is installing foundation piles at the sites of North America's two largest liquefied natural gas (LNG) terminals currently under construction. The contractor has crews working at Venture Global's LNG lique- faction plant in Plaquemines Parish, Louisiana, as well as constructing foundations for the Cheniere Energy Stage 3 Liquefaction Project in Corpus Christi, Texas. This work includes installing ap- proximately 27,000 DeWaal drilled, full displacement, cast-in-place concrete piles to support seven new midscale LNG trains at Cheniere's Texas ter- minal. Deep foundation installation began at Venture Global's Plaquemines facility, located approximately 30 mi (50 km) south of New Orleans, with an initial phase of 24,000 piles. Plans for the Plaquemines LNG terminal include three loading berths on the Mississippi River and four LNG containment tanks. The facility will utilize new pretreatment com- pressors, liquefaction trains and on- site gas turbine power plants to maintain an annual LNG export capacity of nearly 20 million tons (18 million tonnes) per annum. The site's LNG trains are configured in 18 blocks. The contractor is installing piles through an initial 6-20 ft (1.8-6 m) of cement mixed improved soils, which provide a safe work plat- form for equipment to operate on the extremely weak native soils. Drilling continues through soft clay in the subsurface and tips into a stiff clay or dense sand layer. Production piles are drilled to depths up to 124 ft (38 m) below ground surface. The firm is working with engi- neering, procurement and construction contractor KZJV, a Kellogg Brown & Root and Zachry joint venture, at the Louisi- ana location. The foundation team mobilized at the Plaquemines site in May 2022, to install 16, 18 and 24 in (400, 450 and 600 mm) diameter test piles to depths of 90 and 120 ft (27 and 36 m). The piling contractor returned in September 2022, to start Phase 1 of the deep foundation project, beginning installation of production piles.

Apr 1, 2023

By Gerald Verbeek, Erick Baziw

Stone columns are used in geotechnical site remediation to increase load-bearing capacity and reduce settlement of foundations. Stone columns also improve slope stability and increase the shear strength of a soil. A very challenging problem is to characterize the in-situ shear wave velocities from data acquired from Downhole Seismic Testing (DST) after the insertion of stone columns. DST is an important geotechnical testing tool for site characterization that provides low strain (<10-5) in-situ interval compression and shear wave velocity estimates, but the postanalysis of seismic data acquired from DST in the presence of stone columns is very challenging due to the resulting complicated in-situ soil conditions. To obtain the right results it is necessary to use an algorithm that incorporates source wave raypath refraction. Starting with the Normal Moveout Seismic Cone Tomographic Testing (NMO-SCTT) algorithm developed some years ago, this paper outlines the modifications and additions made to this NMO-SCTT algorithm to facilitate stone column site characterization. To dramatically reduce the optimal solution space for the estimated interval velocities the paper also described a priori conditions that are applied based on the unique nature of the stone column site conditions.

By K. Fujita

In order to deal properly with the fundamental aspects of pile construction, the following problems and their solutions are introduced: For driven piles - stresses, damage, movements of surroundings, compaction of ground, deviation of pile direction and location, selection of pile hammers and penetrability of piles are important factors. For drilled piles -loosening of the ground, supports for boreholes, minimizing ground loosening and defects are critical items. Attention should be given to changing soil characteristics. Also, supervision by experienced engineers and good workmanship by skilled laborers are recommended to ensure the quality of the piles.

Jan 1, 2010

By Yuji Yamashita, Kazuyoshi Kamimura, Tsuyoshi Takahashi, Naoya Matayoshi

"The CDM-LODIC method (cement deep mixing - low displacement and control) method enables ground displacement to be reduced by removing an amount of soil equivalent to that of injected cement slurry and the volume of the plunged mixing tool, which causes a certain degree of ground displacement. Since the CDM-LODIC method was developed in 1985, it has been applied to over 930 sites and the accumulated volume of stabilized soil has now reached 7.6 million cubic meters.In the CDM method, the number of blade rotations per unit depth in the ground when the mixing blades are withdrawn is considered a construction item. The blade rotation number depends on the degree of mixing between the cement slurry and the ground Some field tests were performed based on the degree of mixing between the cement slurry and the ground. In these tests, a new concept of evaluating the blade rotation number when the screw rod penetrates to a given depth without injecting cement slurry has contributed to the degree of mixing. Furthermore, a correlation exists between the coefficient of efficiency of soil removal and the cement slurry admixture rate. In this paper, we discus the data collected in those field tests and present some application examples.OUTLINE OF CDM-LODIC METHODThe injection of cement slurry may cause some ground displacement during Cement Deep Mixing (CDM). In recent years, due to an increased demand for ground improvement work in urban areas, there is increased concern that buildings near any CDM site may be adversely affected. The deep mixing method which reduces displacement due to mixing (CDM-LODIC method) enables ground displacement to be minimized by removing an amount of soil equivalent to the injected cement slurry and the volume of the mixing tool, which itself causes some ground displacement. When the construction site is near other structures, regardless of whether on or under the ground, the CDM-LODIC method can be used in order to minimize any ground displacement. There are considered to be two main causes of ground displacement as shown in Figure 1. Displacement A indicates ground displacement caused by the volume of the inserted mixing tool during the penetration stage and displacement B indicates ground displacement caused by the volume of the injected stabilizing agent. Thus, by removing soil equivalent to the volume of the inserted mixing tool and the injected stabilizing agent, ground displacement can theoretically be minimized. Figure 2 shows the amount of observed ground displacement in the cases of CDM and CDM-LODIC at an actual site. These case studies indicate that ground displacement can be reduced by removing the soil."

Jan 1, 2015

By Hyunsuk Yoon, Kiho Lee, Juhyng Lee, Younghoon Jung, Junboum Park

"The environmental double pile method is presented as a device to improve the engineering properties and to clean up contamination of low-permeability soil. This method is one of the novel technologies based on the concept of one step process. It can be applied to low permeable contaminated ground for site reuse. It uses piles to improve drainage, contaminant remediation, and bearing capacity of the ground. To evaluate the on-site applicability of this technology, drainage and strength properties of the environmental double pile were assessed by a series of experiments and numerical analysis. Environmental double pile was found to be a feasible alternative method to improve contaminated soft ground.Korea is a peninsula with many coastal industrial zones. These zones are located in regions mostly underlain by soft ground with low permeability and adjacent to industrial areas that can be contaminated. Therefore, a new region-specific remediation method is required to achieve environmentally sustainable development. This research introduces the Environmental Double Pile (hereinafter, refer to as EDP) for the lowpermeability contaminated ground and focused on both contaminant remediation and soft ground improvement. Basically, the EDP is quite similar to sand compaction pile (SCP). The SCP has been studied extensively to improve soft ground (Braja 1999; Hansbo 1994; Madhav and others 1978; Taylor 1948). But unlike SCP, EDP is filled with oyster shells instead of sand and an inner pile is inserted in the center of this oyster shell filled-zone. Therefore, it is a double pile consisting of the oyster shell pile and the inner pile, as depicted in Fig. 1."

Jan 1, 2005

By Bartho J. Admiraal

"As part of the Schiphol-Amsterdam-Almere project, the largest aqueduct in Europe is being built in order for the A1 motorway to cross the Vecht River. The A1 consists of 12 lanes and the total width of the aqueduct will be 65 m (213 ft). The total length of the structure will be 620 m (2035 ft). Speed of construction is essential for the DBFM-contract, which forms the primary reason for choosing a building method with a horizontal water retaining barrier created by low pressure grouting. After final checks on the water tightness of the silica based layer (softgel), excavation to a depth of approximately 12 m (40 ft) below the water table could be started in order to build the aqueduct.This paper presents a new approach for the calculation of the required grout volumes needed to ensure a “softgel” layer without gaps or holes. The approach applies measurement of deviations due to execution aspects in a probabilistic model. With this model, one is able to study the effects in a field application, i.e. multiple rows of grouted spheres. The results are visualized in order to analyze the risk of holes more easily. It is evident that the existence of a hole means a major leakage. By completing multiple runs, the strategy for grout volumes can be adjusted to minimize this risk.INTRODUCTIONThe Dutch Department of Waterways and Public Works invests over € 4 billion between 2012-2020 to increase the capacity of 63 km (41 mi) motorways of one of Holland’s major corridors. The A1/A6 will be transformed over a distance of 20 kilometers (13 mi). Near Muiden, the current drawbridge on the A1 for crossing the Vecht river will be replaced by a new aqueduct to be located slightly south of the existing bridge."

Jan 1, 2016

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.