Search Documents

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By D. Mu

A method is presented for evaluating the effective gas diffusion coefficient of porous media. A series of random-distributed porous solids with different porosity are generated, a solution of the gas diffusion equations inside the porous media is obtained using the finite element method (FEM), and then the effective gas diffusivities are computed. The results show that there is a percolation threshold sp, and this percolation threshold decreases with an increase in the connectivity of the pore network; the relationship between the effective diffusivity and the porosity is strongly nonlinear when the porosity £ is less than about 0.2; and is quasi linear for higher porosities. The threshold decreases with increasing the connectivity of the pore network. A formula relating the effective diffusion coefficient with porosity is proposed.

Jan 1, 2005

Presentation Overview ?WRDC Purpose and Activities ?Women in Trades, Technology and Operations (TTO) Occupations ?Factors in Successful Recruitment / Retention of women (VBNC) ?Recruitment and Retention Strategies ?Conclusion Women in Resource Development Committee (WRDC) ?Incorporated in 1999 as a Not for Profit Organization ?Based in Newfoundland and Labrador ?Works to Increase the Participation of Women in Natural Resource Industries ?Research (Using Gender-Based Analysis) ?Career Exploration Programs for Women and Girls ?Outreach and Advocacy ?Policy Development ?Public Awareness and Education ?Gender Sensitivity Training ?WRDC Educational Resource Centre

May 1, 2006

By Norman M. P. Low

"IntroductionIndustrial applications of mica utilize two commercially important varieties of mica: muscovite and phlogopite. Muscovite mica is a potassium mica with a general chemical formula, H2KA1(Si04)3 h, and is sometimes referred to as a potas hsilicate. Phlogopite is a magnesium mica having a general chemical formula, H2KMgSi(Si04)3, and is distinguished from the muscovite mica by its decomposition in sulphuric acid.Canada is one of the major natural mica producers in the world. A large tonnage of the mica powders is at present mined and processed in the Eastern Townships of Quebec. This Canadian mica is of the phlogopite type. A closely related mineral of the mica family which is widely used in the construction industry is vermiculite. It is a dehydrated magnesium-aluminum-iron silicate characterized by a foliated structure. Expanded vermiculite, which is often referred to as exfoliated mica, is used as many types of thermal and acoustic insulation, as loose fill in buildings, as an aggregate in concrete, as an ingredient in plaster and insulating concrete , and in fire-proofing compositions. Natural phlogopite and muscovite mica powders are used extensively as reinforcing agents in organic polymers. They also have a wide range of applications in commerical products. For example, dry-ground mica powders are used in large tonnage as a surface finish in roofing materials and as a bonding agent in wallboard joint cement. Common products such as paint, rubber, plastics and welding rods contain mica. Recent studies have also shown that mica powders can be added to portland cement in the preparation of concrete products, as they could improve the tensile strength of the concrete products. The potential and possible"

Jan 1, 1982

By M. R. Henzinger, W. Schubert

"The quality of the backfill applied at a shield driven tunnel is of significant importance failure of the lining. The used material also affects the interplay between support and excavation behaviour.In this research the state of the actual bedding situation is investigated by an analytical approach, laboratory tests and numerical simulations. The numerical simulation using continuum methods have shown shortcomings. These shortcomings regarding the instability of large strain simulations restrict the possibility to reproduce the relocation of the backfilling material. The performed scaled model tests have shown that the regripping process of a double shielded tunnel boring machine affects the soil failure within the gap. With the analytical results the influence of the wall friction can be predicted. Therefore the angle of the failure surface can be determined. The results have shown that the wall friction significantly increases the failure angle. INTRODUCTIONFor tunnel boring machines (TBM) with single (SM) or double (DSM) shield, precast liningsegments are used as rock support. These segmental linings are installed within the protection of the TBM shield. In order to reduce the friction while advancing, the shield diameter is smaller than the diameter of the cutter head and therefore also smaller than the excavation boundary. The difference depends on the expected radial convergences. Since the lining segments are mounted within the shield the steering gap between the shield and the excavation boundary increases and is hereinafter called annular gap.In the process of tunneling in hard rock, the annular gap is usually filled with fine grained and closely graded gravel, termed as pea gravel. The backfilling process starts as soon as possible after the shield tail passes the lining. Due to the operational procedure within the working area of a TBM, a fully backfilled annular gap might not be established after every ring closure. This leads to an unfavorable distribution of the pea gravel leaving the segmental lining partially without bedding. Segmental linings can develop sufficient resistance only when properly bedded."

Jan 1, 2015

By Don Lemmen

Impacts, Adaptation and Vulnerability ? regional climate changes (temperature and extreme events) have already affected many physical and biological systems ? natural systems are vulnerable to climate change, some will be irreversibly damaged ? many human systems are sensitive to climate change ? Projected changes in climate extremes could have major consequences

Nov 1, 2002

By Desmond M. Connor

"The State of the EnvironmentRecent data from a State of the Environment report prepared in January 1991 and released in April (see references) , indicates that the physical and biological environment across Canada is deteriorating in some important ways. For example: • emissions and atmospheric levels of CO2 are rising at a rate more than 50% of the U.S. increase; global temperature continues to rise, especially during the last decade;• while S02 emissions have been falling since 1984, NOz has declined only slightly since that time; N02 in Canada rose 43% during 1970-87, compared with a 7% rise in the U.S.;• municipal discharges of phosphorus and BOD (biochemical oxygen demand) to fresh water have been rising steadily since 1983);• pulp and paper mill discharges to fresh and Pacific coastal waters have been rising, 1970-87;• migratory game bird populations (Prairie Mallard, Northern Pintail) have been declining for the last 20 years;• total per capita energy use continues to climb.The State of the PublicSimilarly, data from recent public opinion surveys shows that public concerns about the environment are either rising, or are remaining at a high level despite the competing claims of the economy and political events for attention.For example, Professor Reginald Bibby's national survey this year shows that Canadians rank our top three issues as theeconomy, the environment and government incompetence.An Angus Reid survey commissioned by the Mining Association of Canada and other mining organizations in 1989 showsthat, despite general support for its economic benefits:• 67% of the general public perceive the mining industry to be a major source of pollution and environmental contamination;• 68% believe that a new mine should not be developed if it will disturb local wildlife;• 52% would prohibit a new mine if it required a road through a national park;• 49% would disallow mine development if it took as much land as an average farm in an agricultural area or if it limited sports fishing in a local lake."

Jan 1, 1991

By K. E. Waters, N. Brodusch, R. Gauvin, C. Teng, H. Demers

Rare earth elements play an increasingly important role in renewable energy devices and high-end electronics. In this project, the composition and morphology of REEs-bearing minerals are characterized with a field-emission scanning electron microscope at high spatial resolution and high counts rate using an X-ray silicon drift detector system. High spatial resolution imaging and energy dispersive X-ray microanalysis were applied at low and high magnification to obtain the composition of each phase in the minerals. From the standardless quantitative analysis results, the amount of REEs in each phase was measured and the relationships between those phases were identified.

Jan 1, 2014

By R. Phillips, A. G. Doll, D. J. Barratt

"The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less.This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference."

Jan 1, 2012

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By R. J. Rotzinger, K. W. Major

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By Stephen Mcgibbon, Tim Twomey

"Abstract - The High-grade Zone (HGZ) was discovered 5000 ft (1520 m) below surface in the hangingwall of the existing orebody, 46 years after the Red Lake mine first went into production. The very rich ore of the HGZ is characterized by a remarkably abundant distribution of visible native gold. The location of this discovery challenged conventional wisdom at the time and its genesis has yet to be fully understood. Textural observations of ore within carbonate veins as well as crosscutting relationships suggest peak-metamorphic emplacement for at least some of the gold. Post-lamprophyre dike remobilization of gold is locally observed in the HGZ. Structure and dilatancy were the key elements for localizing ore at the Red Lake mine. Ore occurs where a fault trend intersected folded ultramafic volcanic rock that created a semi-permeable cap-rock to ore fluids ascending the "feeder" structure. This was enhanced by strong competency contrasts between the eastern ultramafic rocks, felsic volcanic rocks west of the HGZ, and the mafic volcanic host to ore - an exceptional environment for the development of protracted dilatant fluid pathways for gold deposition.Development in the HGZ began in February 2000 and reached commercial production on January 1, 2001 at a capital cost of US $53 million. December 2001 reserves are 1.9 million short tons (1.73 Mt) at an average cut and diluted grade of 2.05 ounces per ton gold (70.5 g/t) containing 3.8 million ounces of gold. The extremely rich ore presented a unique challenge in grade estimation for the Geology Department at the mine. The historic cutting factor was replaced by a statistical method as more data were collected from mining and mill reconciliation. The mine produced 503 000 ounces of gold in 2001. Exploration at the mine is targeting HGZ-type ore formation within basalts associated with the intersections of fluid pathways and folded ultramafic rocks, as well as other targets."

Jan 1, 2001

By H. Sipilä, H. Vartiainen, H. Paarma

"The carbonatite massif of Sokli includes several low-grade Nb showings composed of ores and wastes as identified by routine analyses. More detailed lithologic proportions were determined in two orebodies in the Kaulusrova Nb-mineralized area by a careful geological study and by thorium radiation measurement on 10 cm-long drill core cuttings with a total length of 460 metres. The distribution of Nb in eight X-ray spectrometrically analyzed drill core sample intervals (totalling 35.8 m) was determined by analyzing the intervals semi-continuously by an X -MET analyzer. The geological studies suggest that Nb-mineralized bodies are feasible fo r the sorting of are and waste. This was confirmed by the semi-continuous determination of Nb on the X-MET analyzer.IntroductionThe Sokli carbonatite complex is located in eastern Finnish Lapland. The main ore of the carbonatite massif is a regolithic phosphorus ore in the weathered crust. Large-scale geophysical measurements and diamond drillings have also established several niobium showings within the magmatic carbonatites. Owing to the complicated geology of the massif, the niobium showings occur as irregular zones o r areas displaying complicated structure, texture, mineralogy and geochemistry (Vartiainen and Paarma , 1979; Vartiainen , 1980). The tonnages in areas such as this are large but the grades in-situ are low . The most intensely studied niobium showing is the Kaulusrova area.The exploitation of these showings depends on the feasibility of applying a sorting technique to upgrade the feed and to minimize the amount of material to be treated in the concentration plant. These possibilities o n the Kaulusrova area have been viewed by a detailed geological and X-MET an analyzing study."

Jan 1, 1985

By Howard J. Handewith

"Tunnel boring machines have been tried in underground mining applications as early as 1957. Although tunneling machines hardly threaten to supplant traditional drill-blast-muck operations for drifting, the latest modern machines offer substantial improvements in progress rates over traditional methods under certain conditions.An evaluation guide is offered which identifies conditions that favour machine boring. Different types of costs related to the use of a tunnel machine are discussed. The advantages of the tunnel machine over the traditional method are reviewed. IntroductionThe first tunnel boring machine ever used in a mine was in Quebec in the year 1957. Although less than successful at the time, this experiment served to illustrate the mining industry&apos; s willingness to try new ideas. Since 1957, the manufacture of tunnel boring machines has developed into a full-size industry. Most contractors in Europe and North America will now consider the use of a tunnel boring machine first on any long tunnel that can have a circular section.The modern tunneling machine offers a great potential to the mining industry. Just as the blasthole and raise drill machines have revolutionized mining in the last decade, it is expected that tunnel boring machines will make an equal impact in the future.This is not to suggest that tunnel boring machines will replace explosives in the foreseeable future, but they can supplement drill-and-blast operations. In areas where long drifts, inclines, declines or cross-cuts are needed in a hurry, the tunnel boring machines offer the fastest way to a production return on investment. Figure 1 shows the range of production that two types of tunnel machines have produced as compared with conventional excavation methods in various ground conditions.Rotary hard-rock tunnel boring machines (Fig. 2) commonly produce progress rates in excess of 20 metres per day in uniform ground from 300 to over 2,000 kgl cm2 in unconfined compression strength . These averages are for the completed tunnels. One 7. I6-metre-diameter tunnel boring machine just completed a 1O.7-km tunnel in hard rock of 700 to 2,800 kg/cm>, The last eight months of production averaged 30 metres per day."

Jan 1, 1980

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

Abstract-The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. The batholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering 5000 km2 shows a close connection between a gold-mineralized trend and one of the major shear zones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade (up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W- Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. Thebatholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering5000km2shows a close connection between a gold-mineralized trend and one of the major shearzones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade(up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W-Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By Xu Feng, Han Shufeng, Zhu Bin, Wang Mingming

Due to urban subway tunnels mostly built in the cities with highly density buildings, the geological and construction conditions is complex, especially certain sections of the subway tunnel will pass through from the foundation of the overpass, therefore the stability and surface deformation control of that section’s tunnel excavation is particularly important. Taking Xi'an Metro Line Three interval tunnel as a research object, we have used FLAC3D simulation to analyze the tunnel’s surrounding soil deformation and tunnel lining stress distribution under bridge foundation with shallow buried covered excavation method. Analysis results show: (1) After the excavation of the tunnel right line, due to the bias of the upper bridge foundation the right of the tunnel showed relatively large deformation. In order to ensure the construction safety, we recommended using the grouting anchor reinforcement on the right side wall to further control the deformation zone. (2) The maximum vertical displacement of the ground occurred in the right wall of the tunnel portion which was due to the intensity of soil outside the grouting range of the arch is low, as a result the deformation is larger; this position requires special attention, strengthening the monitoring measurements of this part is necessary to avoid the large deformation and other adverse effects of the upper portion of bridge foundation. (3) The maximum vertical force area of the initial lining of the tunnel is in the middle of the side wall, while the second lining in this part of forces is smaller, thus at the beginning of the construction of the liner, attention should be paid to this area. On-site grouting or steel bracing reinforce support may be used if necessary.

Jan 1, 2015

By D. Seo, P. Au, S. Yandt, N. Tsuno, A. Sato

Nickel-base single-crystal superalloys are used for gas turbine airfoil applications due to their excellent high temperature properties. A good understanding of the mechanical response of these alloys under different temperature and loading conditions is essential for modeling their behavior. In this study, the low cycle fatigue behavior of CMSX 2 oriented with the loading axis along [001] was investigated under zero-compression strain-controlled loading at 1100°C. The experiments were performed with or without a two-minute dwell (hold) in compression. The microstructure before and after testing was analyzed to understand the deformation characteristics including the effect of dwell.

Jan 1, 2010

By A. W. Chan

"An interactive computer simulation model of conveyor systems used in oil sands mining has been developed to aid in the selection of mining equipment and the evaluation of operating policies. The materials handling links between supply points, such as bucket-wheel excavators and draglines, and demand points such as bins and extraction plants are modelled in such a way that the conveyor model can be interfaced with any combination of these equipment submodels. Detailed calculations of the power demand of each conveyor section based on operating characteristics and conveyor design parameters are included to permit the close monitoring of energy requirements. Various interactive features are incorporated so that an operator can not only monitor, but also control, the mining operations in the model and experiment with different operating strategies.IntroductionThe interactive simulation model of conveyor systems described in this paper is one of a number of detailed computer models being jointly developed by the National Research Council and Canstar Oil Sands Ltd. on the mining equipment and operations used in oil sands mining. Reference I presents an overview of this whole series of models, their interrelationships and the underlying motivation for their development.A network of conveyors constitutes one of the practical ways for transporting mined material in an oil sands plant. The materials handling links between supply points, such as bucket-wheel excavators, bucket-wheel reclaimers and bins, and demand points such as dumps, bins and extraction plants can be represented by a series of interconnected conveyor sections. For example, the fluctuations of the feed rate at the bucket-wheel excavator, the flow of ore material through the conveyor network and the arrival of this material at the extraction plant can be simulated."

Jan 1, 1982