Search Documents

By I. Orford, V. Rozon

"The Sä Dena Hes Joint Venture Mill was designed to process 450,000 tonnes per year of ore grading 11.3% lead and 13.2% zinc.Run of mine ore is crushed in a jaw crusher and then ground in a closed circuit SAG mill and ball mill. A standard differential float in conventional flotation cells produces quality lead and zinc concentrates. Dewatering of concentrates is achieved using high rate thickeners, lamella clarifiers and pressure filters. Process water is 100% recycle.Plant design was based on metallurgical test work performed on drill core samples. The plant is operating at better than design specifications.INTRODUCTIONSä Dena Hes Joint Venture was formed in 1989 to develop the Sa Dena Hes lead/zinc sulphide mine, located approximately 45 km north of the Town of Watson Lake, Yukon. The mine is owned by a Joint Venture partnership between the operator, Curragh Inc. (87.5%) and Hillsborough Resources Limited (12.5%).The project was completed in a record ten months, working throughout the severe Yukon winter and through an abnormally wet spring and summer. The first truckloads of concentrate were shipped from the mine on August 1, 1991.The mill currently processes 550,000 tonnes of ore per year grading 6.9% lead and 11.5% zinc. Ore is crushed in a jaw crusher and ground to 60% passing 75 microns in a closed circuit operation of one SAG mill and ball mill. Using conventional flotation cells a 150,000 tonnes of concentrate is produced in a year with lead concentrate grading 78% lead and a zinc concentrate grading 60% zinc at overall recoveries of 89% and 90% respectively.Concentrates dewatering is accomplished using high rate thickeners, clarifiers and pressure filters. The lead concentrate and zinc concentrate contain 5.4% water and 7.8% water respectively. Concentrates are trucked to Skagway, Alaska for subsequent shipping to overseas smelters."

Jan 1, 1993

By Z. Zhang, X. -G. Chen, F. Breton, A. Arici

"The microstructure of Al-10Si-0.3Mg-0.5Mn alloy with 0.27% Zr and 0.19% V addition was quantitatively analysed and compared to the base material. The addition of Zr and V in the AlSi10Mg alloy exhibit a beneficial effect on the Si modification, resulting in the reduction of the size of eutectic Si particles on both as-cast and T6 conditions. The quantitative image analysis results show that the Zr and V addition and T6 treatment can reduce the size of the intermetallic phases. In addition, the presence of Zr and V is favour to the partial dissolution of the intermetallic phases during the T6 treatment. Different heat treatment procedures were tested to optimize treatment parameters. The mechanical properties of the alloys were evaluated using hardness measurements and tensile tests. The results show that the addition of Zr and V can remarkably improve the mechanical properties on as-cast and T6-treated conditions. The correlation between the microstructure and mechanical properties of the alloys is discussed.INTRODUCTION Al-Si-Mg foundry alloys have been widely used in automotive and aerospace industries due to their high strength-to-weight ratio, heat-treatable capability and excellent castability. The alloying elements such as Cu, Mn, Fe are traditionally added into Al-Si-Mg alloys to improve their mechanical properties (Mohamed, Samuel, Samuel & Doty, 2009). In recent years, the attention has been paid to the effect of the transition elements such as Zr, V, Ti, etc, as minor alloying additives, on the properties of aluminum alloys (Elhadari, Patel, Chen, & Kasprzak, 2011; Kasprzak, Amirkhiz & Niewczas, 2014; Shaha, Czerwinski, Kasprzak, Friedman & Chen, 2015; Shaha, Czerwinski, Kasprzak & Chen, 2014; Mahmudi, Sepehrband, Ghasemi & 2006; Meng, Cui, Zhao & Zuo, 2013). Kasprzak et al., (2014) and Shaha et al., (2015) reported that additions of Zr, V, and Ti in Al-Si-Cu-Mg cast alloys can improve the alloy mechanical properties at high temperature by forming stable intermetallics and precipitates on as-cast and heat treatment conditions. On the other hand, the mechanical properties of near-eutectic and eutectic Al–Si cast alloys depend not only on the chemical composition but also, even more importantly, on microstructural features such as the morphology and size of eutectic silicon and intermetallic particles, which are present on both as-cast and heat treatment conditions (Mohamed et al., 2009). However, there is rather limited information on the effect of Zr and V on the microstructure features and mechanical properties of near-eutectic Al-Si-Mg cast alloys."

Jan 1, 2018

By Jacob Wood, Robert Matusewicz

The Outotec® Ausmelt Top Submerged Lance (TSL) Process has achieved widespread commercial acceptance over the past 40 years for the processing of copper, nickel, lead, tin, zinc and precious metal bearing feeds. The continual development and evolution of the technology during this period has resulted in a more intense smelting process with higher energy efficiency and lower operating costs. More recently, considerable effort has been invested in decarbonisation of the process through improvements such as increased oxygen usage, dry feed injection and use of low-carbon auxiliary fuels. This paper covers a number of these recent advances to the technology and highlights their impacts on energy consumption and CO2 emissions for a range of non-ferrous smelting flowsheets. INTRODUCTION Relentless demand for improvements in the profitability, safety and environmental performance of non-ferrous smelting plants has driven a continual development and evolution of processing technologies in this industry. In response to these demands, a number of bath smelting technologies have emerged over the past 40 years and have been implemented for the treatment of primary and secondary feedstocks. The Outotec® Ausmelt Top Submerged Lance (TSL) Process (henceforth Ausmelt Process) is one such bath smelting technology which has been widely adopted in a large number of greenfield projects and brownfield plant modernisations (Wood & Hughes, 2016). Emissions of CO2 from the production of non-ferrous metals represent approximately 4-5% of global totals (Rankin, 2012), comparable with the almost 10% attributed to iron and steel production. Despite significant improvements in the energy efficiency of modern smelting technologies (Coursol, Mackey, Kapusta & Cardona Valencia, 2015), primarily through increased oxygen usage, further innovation and development is still required to address their reliance on fossil fuels such as coke and coal. Transformation of the non-ferrous smelting industry to low-carbon technologies and process flowsheets is lagging behind the power and transport sectors, which have witnessed significant growth in clean/renewable energy technologies to reduce CO2 emissions and address the issue of anthropogenic climate change (IRENA, 2018; IEA, 2018).

Jan 1, 2019

By Unkown

The Province-wide road ban on movement of heavy loads has had the effect of curtailing or stopping development in several areas. In the Leduc area, the discovery well has been restricted in flow to only a fraction of normal due to limited storage space, but drilling at Imperial Leduc Nos. 2, 3, and 4 has been continued for the past few weeks. The No. 2 well is within 100 feet of the producing horizon and should be completed within the next few days. According to reports, it has been logging slightly lower, structurally, than the discovery well, but, regardless of the outcome, it has been an important test to determine westerly cross-section of the Leduc structure. No official reports have been made available of any tests made during the drilling of the well, but it is understood that promising oil and gas shows have been indicated in higher formations. Actual drilling operations have not been commenced by any of the other companies holding leases in the immediate area but it is expected that, when road bans are removed and equipment is assured, several wells will be commenced. Announcement has been made that Imperial Oil, Limited, will drill a well near Battle lake, about thirty-five miles southwest of the Leduc field. Location of the well has been made following an extensive seismograph survey of the area, with total depth of the test well expected to be in the 8,000- to 8,500-foot range. Drilling will be done with the heavy-duty rig last used at the De Winton test. Imperial Oil have abandoned hope of oil production in the Provost area after drilling nine wells, but will retain their interest in the gas field that has been developed. Of the wells drilled, four indicated gas flows ranging from 1,060 to 13,200 M.c.f. per day.

Jan 1, 1947

By A. Fyson, M. P. Smith, Margarete Kalin

"Drums containing 0.07 m3 of pyritic waste rock from a zinc/copper mine, with and without Natural Phosphate Rock (NPR) additions (40 kg/t waste rock) were set up outdoors. The effluent chemistry has been monitored over a period of 709 days. In the presence of NPR, the cumulative acidity discharged from 7 out of 8 drums was 80 % less than that discharged from drums without NPR. Mixing NPR throughout the drums was more effective in reducing acidity than placement of the NPR in a layer in the drum. NPR treatment was more effective for 'fresh' waste rock than for material which had weathered for more than 4 years. It is concluded that application of NPR to pyritic waste rock could greatly reduce acidity generated.IntroductionWaste rock dumps are significant sources of acid, generated by the oxidation of sulphides. Oxygen and water supply are oxidation rate-controlling factors, and oxygen supply is the reaction-limiting component. If secondary minerals can be formed on the surface of the rocks, pyrite oxidation and therefore acid generation may be reduced or inhibited. Neutralizing agents such as limestone do not prevent the oxidation of pyrite but treat the resultant acid mine drainage (AMD) or acid rock drainage (ARD).Meek et al. (1991) determined in pilot scale experiments that apatite mixed with tailings was more cost effective than liming or use of PVC liners to reduce oxygen and water penetration into the tailings. Phosphate is not acting as a neutralising agent but it creates a chemical condition on pyritic surfaces which prevents reactions of the oxidising agents. Precipitation of principally iron phosphates physically isolates the pyrite surfaces from further oxidation (Ziemkiewicz 1990; Evangelou 1994). The chemistry of the phosphate effects has been described by Spotts and Dollhopf (1990). Secondary mineral formation was evident in the leach pile at Gibraltar when leaching was impaired (Scott, 1991) indicating a link between oxidation and the mineral-formation process. This paper reports on effluent characteristics when waste rock is generating acid in the presence of NPR."

Jan 1, 1995

By M. Falutsu

"The PSI-200 is a rugged, innovative, and easy to install on-stream size analyzer. Its calibration is simple and can be done on-line, during operation. Two measurements are displayed on the panel, which are expressed as percent passing a selected size, or as any statistical diameter. These two measurements are given as two continuous 4-20 mA output signals. Operation alarms are displayed on the screen or are given as digital output signals.The PSI-200 has been used in various applications at Lakefield Research. Particle sizes ranging from 10 µm to 450 µm have been monitored successfully, with an accuracy of 1- 2%. Having the size measured continuously and reliably, optimum conditions have been established for the grinding circuit, resulting in a superior quality in pilot plant testing.INTRODUCTIONThe challenge of any operating plant is to optimize product quality, maximize throughput and minimize operating costs. The importance of particle size measurement at a grinding circuit is well recognized. Monitoring continuously the particle size and keeping the product as uniform as possible is crucial to the whole mill operation regardless of the nature of the operation.Various techniques and instruments have been developed over the years attempting to give reliable on-line size analysis data. The operating difficulties and the reliability of these equipment still present major drawbacks and none of them proved to be widely accepted.PSI-200 is a relatively new on-line analyzer. The operation is simple and of low cost and the maintenance required minimal. It measures particle size and it displays two parameters of the solids size distribution, either weight fraction of passing a certain size or any statistical diameter. Two analog outputs can be sent to a process control system and through a supervisory control loop the correct action can be taken to maintain the desired particle size (perhaps adjust the feed rate to the grinding mill)."

Jan 1, 1993

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was' put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

By R. R. Potter

"New Brunswick became a separate province in 1784, shortly after the influx of a large number of Loyalists from the United States. Many of these people settled along the Saint John River, including the area of excellent farmland near the present town of Woodstock. There were indications that some of these early settlers recognized iron formations in the vicinity of Woodstock about 1820, however the nature of the deposits was not known until 1836 when Dr. C. T. Jackson, a geologist commissioned by the State of Maine, investigated the mineral potential of the area. Jackson(1) described the ""ore"" as compact red hematite yielding 44 per cent pure metallic iron, and suggested that sizable tonnages may be present. It was about this time that an extensive limonite deposit was found in north-central Maine, near Mt. Katahdin. Other iron depostis were found in the Nictaux area of Nova Scotia, and a few years later at Londonderry* (Fig. 1). In 1837, Richard Ketchum of Jacksonville, on whose land iron ores had been found, petitioned the provincial government to incorporate a company. After much study, the York and Carleton Mining Company Bill was passed on March 15, 184 7. Several other petitions were passed permitting the company to construct roads, obtain woodland, etc. (2) . The first blast furnace was erected in 1848 on the west bank of the Saint John River near the mouth of Lanes Creek."

Jan 1, 1999

By Barbara A. Filas

The IFC goal is to promote private sector investment in developing countries which will reduce poverty and improve people?s lives. The developing country goal is to promote health, education and employment opportunities that improve their economies and their standard of living. The mining company goal is to Promote successful ?triple bottom line? mining projects that will grow shareholder equity

May 1, 2002

By L. Long

Stirred milling of nickel laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on siliceous goethitic (SG), goethitic (G), and saprolitic (SAP) nickel laterite samples (- 2000 ?m particle size) to evaluate the effect of stirrer speed, solid content, water salinity and grinding time. A fine mineral product (-38 µm) was used to evaluate the effect of selective grinding and Ni upgrade. The optimum grinding time for the highest Ni upgrade was 0.25 min, 0.1 min and 0.1 min for the SG, G, and SAP nickel laterite, respectively. A new feed (38-2000 µm) for each nickel laterite sample was prepared for batch grinding tests under the optimum grinding conditions. Upon grinding the 38-2000 µm feed, the - 38 µm product confirmed the effect of selective grinding and nickel upgrade. Size classification followed by stirred milling is a suggested process for Ni upgrade. The best Ni upgrade result was achieved on the SG nickel laterite among the three samples. The Ni grade increased from 0.85% to 1.37%, with 27.8% Ni recovery. Bottle roll leach tests showed that for SG and SAP samples selective grinding had no dramatic effect on Ni extraction due to the slow leach rate of hard mineral particles. Stirred milling of G sample increased the surface area of goethite, resulting in higher Ni extraction. Gravity concentration through a Knelson Concentrator was not effective in the further treatment of the stirred milling products either due to the poor operating conditions or due to the mineralogy characteristics of the feed samples. The energy requirement in the stirred milling was investigated. The first pass of the signature plots study is critical for the purpose of selective grinding, because the best result on selective grinding is achieved in the early stage of the grinding process.

Aug 1, 2013

By Z. D. Hora

Brick shales and refractory clays are mined at Sumas Mountain near Abbotsford. Sholes and stoneware clays elsewhere in the province have not been developed. THE SUMAS MOUNTAIN deposit near Abbotsford, 80 km east of Vancouver, has been in continuous production since 1905. The deposit is exposed in a small outlier and comprises a sequence of alternating beds of clay and sand. Beds are of Eocene age. Within the 400 m thick ness of sediments are seven distinctive conglomerate members, some up to 20 m thick, interbedded with fine grained sediments including claystones and siltstone , or "shales". Shale is quarried to produce a variety of bricks, sewer pipes and similar products; it is also used for cement. Several different shale beds have been mined over the years and exhibit a variety of fired colours ranging from buff-pink grey to deep red; pyrometric cone equivalents (PCE) range from 3 to 20. A layer of fireclay 3 to 4 m thick that occurs at the base of the sequence has pinkish white to light buff fired colour and PCE of 30 to 33. It is used as a 266 primary component to produce refractory bricks. The shale is quarried and processed by Clayburn Industries Limited of Abbotsford. Another similar but smaller outlier of the same geological formation is known from Blue Mountain, about 20 km northwest of Mission. Other ceramic clays in British Columbia are reported from Quesnel (7 m bed of white stoneware clay, PCE 17 to 19), Giscome Rapids (25 km north of Prince George, 10 m bed of stoneware clay to PCE 31) and anaimo-Comox area (buff to red firing "shales", PCE 8 to 10-1 12) . From 1959 to 1974 Cretaceous shale from Saturna Island in the Strait of Georgia was used to produce lightweight aggregate. Similar deposits of expanding shale are known from the vicinity of Duncan on Vancouver Island.

Jan 1, 1984

By H. S. Bostock

"The study of the geology of Mayo district began in 1900 with R. G. McConnell's exploration of Stewart river; and has been carried on intermittently for the Geological Survey of Canada by J. Keele; D. D. Cairnes; W. E. Cockfield; C. H. Stockwell; and the writer. It has revealed a thick group of schists; quartzites; and crystalline limestones; almost certainly Precambrian in age; placed in the Yukon group; and a group of younger intrusive igneous rocks varying in composition from granite to gabbro. These include bodies of many sizes and forms; from stocks 8 miles across to small dykes and sills.Prospecting in the district began about 1897 and has disclosed the presence of gold, silver, lead, tungsten, tin, zinc, antimony, copper, arsenic, manganese, and mercury, both in placer and lode deposits . Of these metals gold, silver, and tungsten have been produced from placer deposits, and silver, lead, and gold from lodes. This paper deals only with some structural relationships of the lode deposits, generally referred to as the silver-lead veins, which have yielded the greater part of the mineral production of the area. From 1938 to 1941 the geological mapping of the district for publication on a scale of 4 miles to 1 inch was carried out by the writer, and the ideas expressed here are based on this work. No comprehensive detailed study of the silver-lead veins has been made, but the mapping has brought to light several important facts. The rocks of the Yukon group, although of a striking sameness throughout their section, can be divided into a number of distinguishable members by means of which the main structures can be traced . The most important and readily distinguishable rock in the group is referred to here as the quartzite member. This is composed of quartzite and schist in about equal proportions. The quartzite is resistant to erosion and forms most of the outcrops of the'member and the peaks of the Gustavus mountains and mount Haldane (Lookout)."

Jan 1, 1954

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. The Ore and ProductsThe mines in the Saskatoon area — Agrium, PCS-Cory, PCS-Allan, PCS-Patience Lake, PCS-Lanigan and IMC-Colonsay — extract the ore from the Patience Lake member. The mines in the southeast corner of Saskatchewan — IMC-K1 and K2, PCSRocanville — extract from the Esterhazy member, while IMC-Belle Plaine, near Regina, solution mines potassium chloride from both potash-bearing members.Ore from the Patience Lake member is a medium-grained mixture of sylvite and halite, with a KCl content of 36%, insolubles averaging up to 5.5%, and little or no carnallite.The ore from the Esterhazy member is a coarse-grained mixture of sylvite (KCl) and halite (NaCl) with a small amount of water insolubles, and some carnallite (a K-Mg chloride). Average run-of-mine grades are about 30% KCl."

Jan 1, 2003

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic metres /day of wastewater containing 30-60 mg/1 zinc. demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic con¬trol equipment, the system has evolved to a full-scale operation capable of treating 800 cubic metres/day of wastewater containing 4-11 gm/1 zinc. Treated effluent contains 0.2-20 mg/1 zinc. The hydroxide sludge produced returns to the metallurgical process for the recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing a return from metal recovery.IntroductionWith the goal of reducing environmental contamination, Hudson Bay Mining and Smelting began laboratory testwork, during the late 1960's, into the methods and technology for neutralizing and removing heavy metals from acid mine drainage. Based on lime treatment, early tests showed much promise and culminated in the construction of a pilot-scale test plant at Schist Lake Mine in early 1971.This pilot system utilized technology developed in laboratory studies, and related to work then underway by state authorities in Pennsylvania coal mines. The basic operation consisted of a lime slurry tank, baffle reactor and a free-settling basin. Through three summers of operation, the Schist plant, capable of treating 600 cubic metres/day of minewater, produced a heavy-metal extraction of 99% under normal conditions. Although successful in proving the treatment chemistry, the plant displayed deficiencies in sludge densification and handling."

Jan 1, 1980

By W. A. Grell

"The oxygen meter has been in use at MacLeod Cockshutt Gold Mines for over a year, At MacLeod about 200 tons per day of reground concentrate containing roughly 10% pyrrhotite and 20% pyrite is cyanided in four 181 x 18' Dorr agitators. A survey by the Department of Mines showed that oxygen content of some of the agitators was rather low. Experience with our oxygen meter indicates that the oxygen content must at times have been too low for good gold dis solution.We have found that in winter, when pulp temperatures drop to about 50° F, oxygen saturation in the agitators is not difficult to maintain. In summer, however, when pulp temperatures rise to 70or 75°F, the oxygen content will drop very readily. It was found that a high oxygen content can be maintained readily if the pulp is sufficiently dilute. Thus at 50° F, a pulp of specific gravity 1. 75 i.e., about 55% solids, will saturate; but at 70 or 75° F, the specific gravity must be decreased to 1 .45, equivalent to about 40% solids, in order to maintain saturation. Very thick pulps, such as thickener underflows, are noticeably difficult to saturate in the laboratory, and lose their oxygen rapidly.Clear solutions, on the other hand, absorb oxygen readily and hold it. The primary thickener overflow, before agitation, is 100% saturated; after storage of 3 to 4 hours it is still 100% saturated at re clarifier tank. Barren solution after spraying in a launder is 100% saturated.We have not yet attempted to determine what percentage saturation is necessary for good extraction, but it is known that there is a point at which extraction decreases rapidly. So far, the measures required to maintain over 80 or 90% saturation have coincided with measures required to hold the reducing power to the point believed necessary."

Jan 1, 1964

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By Patrick Andrieux

Numerous rock blasting design methodologies have been developed over the years, relating either to the primary objectives of blasting, such as the size distribution of the blasted material, or to its undesirable side effects, such as damage to the remaining rock mass. All existing methodologies, while of use, do have serious shortcomings. The question remains whether further improvements can be achieved in the field of practical rock blasting engineering. One approach that seems to hold promise is the relatively new matrix-based rock engineering systems (RES) methodology. It has been conceptually demonstrated that RES could be efficiently adapted to blasting. A brief overview of rock blasting design techniques and their main shortcomings is followed by the basic concepts governing rock engineering systems and a discussion on their pertinence to blasting. The paper concludes with a review of current efforts to develop a useful practical blast design tool using RES. SOMMAIRE Le potentiel d?application des systèmes d?ingénierie du roc aux tirs à l?explosif. De nombreuses méthodologies de conception d?abattage du roc à l?explosif ont été développées au cours des années, qui ont adressé soit les principaux objectifs des tirs, comme par exemple la granulométrie du matériel dynamité, soit ses effets secondaires indésirables, tels les dommages au massif rocheux. Toutes les méthodes existantes fonctionnent dans une certaine mesure et sont utiles - elles sont cependant pour ainsi dire toutes affectées par des limitations ou défauts plus ou moins sévères. La question demeure quant à savoir si des améliorations supplémentaires peuvent être apportées dans le domaine de la conception pratique des opérations d?abattage du roc à l?explosif. Une approche alternative qui semble prometteuse est celle relativement récente des systèmes matriciels d?ingénierie du roc (?Rock Engineering Systems?, ou RES). Il a été démontré de manière conceptuelle que les RES ont le potentiel d?être adaptés aux opérations de sautage. Une brêve revue des principales techniques de conception des tirs à l?explosif est suivie d?un énoncé des principes de base gouvernant les RES, ainsi que d?une discussion sur leur pertinence aux opérations de tir. Cet article conclut avec la revue d?un projet de recherche axé vers le développement d?une méthodologie de conception des tirs à l?explosif basée sur les RES.

May 1, 2002

By Ali Hashemi, Anna P. Perry

The PQ Deeps (PQD) is a production zone located at Newmont’s Musselwhite Mine in northern Ontario. Development started for the PQD in late 2017, and the first stopes were mined starting in early 2021. Unlike most historic longitudinal stoping of narrower orebodies at Musselwhite, the PQD is a wider orebody following the plunge of a fold hinge and is extracted primarily by transverse stoping. Some geotechnical challenges were experienced during early stoping efforts, necessitating design changes throughout late 2021 and early 2022 to optimize the stope design. This work describes the mining methods and design changes to transverse PQD stoping based on geotechnical lessons learned during early stoping efforts.

Jan 1, 2023

By W. F. James

"The property of Siscoe Gold Mines, Limited, comprises about 1,600 acres, including Siscoe island and adjacent claims under water in Montigny lake, in Dubuisson and Vassan townships, Quebec.For many years the property was reached by way of Harricana river and its chain of lakes from Amos, Quebec, about 45 miles distant. In later years a highway has been built from Noranda east through Val d'Or, about 5 miles distant.Gold was discovered on one of the claims on the north shore of Montigny lake as early as 1911, but these gold discoveries have never been economically important. Several years later gold was discovered on Siscoe island and considerable surface work was carried out. Still later, iscoe Gold Mines, Limited, was formed and carried out further work, some of it through shallow shafts. In 1928, larger scale operations were undertaken and a 100-ton mill was constructed. In the years following, production· was on a larger scale with lower grade, until finally a milling rate of over 1,000 tons a day was attained. Approximately 1,500,000 tons were treated between the end of 1940 and mid-year 1945. At present the milling rate is down to about 200 tons a day and work is confined chiefly to some of the less important veins that have been recently developed.The following is a summary of production up to December 31st, 1946:"

Jan 1, 1954

By J. E. Gill, A. R. Byers

The Surf and Pugsley gold-copper mines; owned and operated by Surf Inlet Consolidated Gold Mines; Limited; are about 6 miles inland from; the head of Surf inlet; on Princess Royal island; Skeena mining division; British Columbia. Surf inlet is a fiord 360 miles in an air line northwest of; Vancouver.

Jan 1, 1954