Search Documents

By R. W. Seedsman

In 1984 and 1985, two 7.6m diameter TBM tunnels were driven from the Donkin-Morien peninsula in Nova Scotia to access the Harbour coal seam. The design of the ground support was based on identifying zones of rock failure through the application of the Hoek Brown failure criterion and the early use of finite element analyses. In 1992, the mining project was abandoned and the tunnels allowed to flood. Monitoring data from the tunnel was subsequently used as a case study in the development of the concepts of brittle rock behaviour. In 2007, the tunnels were pumped out as part of a feasibility study into the reintroduction of longwall mining into the coalfield. There is a good match between observations of the collapse zones in the roof and sides of the tunnel and a simple elastic analysis using brittle parameters, a spalling limit of 5, and a low independent shear modulus. The brittle analyses form the basis of the design for the resupport of the tunnels.

May 1, 2009

By Ju-hyung Ha

New automated curing system for mass concrete has been developed to improve the quality of concrete structure and to save construction time and cost. The principle of this system is the automated water circulation system of heated curing water. Applied curing water on the surface of mass concrete keeps the temperature difference between center and surface of the structure below the threshold of specification. Mock-up test and field application have been conducted to investigate the performance of this system. In the results, new automated curing system reduced the chance of thermal crack occurrence and improved quality of the concrete structure as well.

Aug 1, 2013

By T. Stergiou

An extensive research is being carried out on the shaft furnace operation in order to minimize down-times and reduce operational cost. The need to increase the scrap percentage on the charging mix, together with the need of cheaper spare parts has led to the investigation of alternative materials for the burner system on the shaft furnace. This system consists of a burner block and a flame holder. Traditionally these items are constructed either from SiC ? oxide bonded or SiC-nitride bonded. A lot of problems have been confronted over the past 8 years of operation. Usually, large cracks are formed on both flame holders and burner blocks. This resulted in leakage of combustion gases to the back of the lining and a quick erosion of it. Additionally, the burner blocks suffer from chemical erosion, due to the increased amount of scrap used in the charging mix and the presence of slag inside the furnace. Alternative materials such as stainless steel for the flame holder and alumina-chromia refractory for the burner block have been tested in terms of life-time and resistance on chemical erosion. Furthermore, additional changes have been made on the burner block design in order to alter the flame shape and improve the scrap melting operation.

Jan 1, 2007

By Jeffrey D. Smith, William G. Fahrenholtz, Jose M. Soto

Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy.

Jan 1, 2004

By Laxman (Lucky) Amaratunga, Hisham Madi

Final disposal of mine wastewater neutralization sludge continues to be one of more pressing problems in the mining industry. The disposal of mining and metallurgical waste products into underground reduces the environment impact and improves the safety of the mining operation and the economics of the enterprise. This current research focuses on an investigation of utilization of mine wastewater neutralization sludge obtained from Kidd Creek Mine site, as a supplementary material for their proposed deep mine pastefill system. Their proposed pastefill consist of combination of rock aggregate in a matrix of imported sand and tailings with binder (Portland cement + Slag cement). Pastefill mixes containing various percentages of the waste sludge 0 (control mix), 1, 2, 3, and 5% by weight as replacement to the fine sand were prepared and tested with different percentages of binder. Hypothesis behind this approach is to study the behavior of sludge as replacement of sand in matrix as well as its ability to act as a binder. Compressive strength, percentage of sludge, binder dosage, slump, water to cement ratio, percentage of solid, and curing time are being observed. The results indicated that sludge can be incorporated into the pastefill and enhance its strength without compromising the pastefill quality and integrity.

Jan 1, 2004

By Par G. Jönsson, Joachim von Scheele, D. S. Sarma, Mukul Goyal

Dust from flue gas cleaning systems at iron and steel production is frequently considered as a waste problem, but it is actually a potential raw material source. By using a technology like the oxyfuel based OXYFINES technique, it can be melted into a suitable form. The product from this processing, however, needs to meet the requirements of a recyclable raw material, here particularly a top-charged blast furnace feed. The present work has been focused on characterization of the product produced from these dusts by OXYFINES technology. The investigation has been carried out on samples of processed dusts from a European integrated steel mill. It was done by means of chemical analysis, density measurement, light optical microscopy, X-ray diffraction, scanning electron microscopy combined with energy dispersive spectroscopy, and micro indention hardness measurement. Special attention was paid to the presence of zinc, an element that might be harmful while recycling the material (e.g., in a blast furnace). The results show that the product contains four different regions with different morphologies and properties in the material, which are discussed in detail. The overall conclusion is that by processing the dusts in this way, a raw material suitable for recycling in a blast furnace can be obtained.

Jan 1, 2004

By E. Goodwin

"Maclaren Forest Products Inc.Lime is commonly used for the neutralization of acid, and the removal of heavy metals in mine waste waters. However, the precipitation of heavy metals as hydroxides must take place under conditions of controlled pH, to produce minimum concentrations of dissolved metals. An account is presented explaining the concepts applied to lime-treatment processes at Bell Mine during the period of a supernatant discharge to Babine Lake; October 18, 1982to January 25, 1983. IntroductionBell Mine of Maclaren Forest Products Inc., Babine Mining Division, an open-pit copper mine, is located on Newman Peninsula, Babine Lake approximately 65 kilometres northeast of the town of Smithers, British Columbia (Fig. 1).A depressed market for copper metal in 1982 forced a management decision to suspend operations at the mine for an indefinite period from October 3 I, 1982. For some time prior to the mine closing date, mine management was concerned about the increasing level of supernatant in the tailings pond , and its possible effects on the stability of the dam when cycloning of mill tailings ceased. Consideration of these potential hazards led to an application being filed with the Provincial Waste Management for a permit to discharge the excess water to Babine Lake. This large lake, an important link with several significant salmon spawning sites, is a major contributor to the British Columbia commercial fishing industry. Jurisdiction for the environmental affairs in the area is shared by the Department of Fisheries and Oceans, the Environmental Protection Service, and the Provincial Waste Management Branch. These agencies were directly concerned in the formulation of discharge permit following joint consultation, and exchange of information with the company on environmental concerns. An approval was finally granted to discharge approximately 1,000,000 cubic metres of supernatant from the tailings impoundment at Bell Mine into Hagan Arm, Babine Lake from October 18, 1982 with a daily discharge not to exceed 9000 cubic metres. Provisions were made that a particular discharge procedure be followed, and that the company would be responsible for setting up a sampling and monitoring program to safeguard the quality of the effluent."

Jan 1, 1986

By K. Bowes, M. D. Maley, R. J. Ring

The Honeymoon Uranium Project is an acid In-Situ Recovery (ISR) mine in South Australia. It was previously operated for approximately 18 months before being placed on care and maintenance in 2014, it was then acquired by Boss Resources in 2015. Boss has been performing a number of studies to plan for reopening of the mine, including a successful field leach trial (FLT) in 2017. The current configuration for uranium precipitation at Honeymoon is a batch process. Whilst this achieves effective uranium recovery, the precipitates produced are often very fine, with poor settling and solid/liquid separation characteristics. Continuous precipitation, involving recycling of solids, has reportedly been successfully utilised in other operations to increase the particle size and density of the product, leading to solids that can be more readily dewatered, dried and drummed, with less fines and dust generation. However, no operational data are available from such operations.

Jan 1, 2020

By S. Mamonov, V. ?shikhin

"The purpose of work was the significant increase of copper recovery from slag at a concentrating plant. Analysis of study of slag phase composition showed the perspective of a slow slag cooling method due to its recrystallization and transition of primary copper minerals to secondary.Copper content in base slag varied between 0.71 and 0.96%. The study of a degree of copper minerals release of the slowly cooled slag in comparison with a yielding slag showed that in a flotation size grade –0.071 mm of yielding slag the weight ratio of released copper minerals grains is 58.95% against 86.73% in samples of slowly cooled slag. The process flotation sheet consists of three main, one control and two cleaner flotation operations with aftergrinding of middling products. A reagent mode was differed from a factory one by decreasing the slurry pH from 11–12 to 8–9. This paper shows research results of the slurry alkalinity impact on technological indexes of beneficiation (flotation).Industrial testing of a resulted batch of slowly cooled slag at “SUMZ” concentrating plant showed the efficiency of such processing: copper recovery to a copper concentrate increased by 15–19%.INTRODUCTIONIntensive development of mining and metallurgy industries within a 250-year period in the Ural region led to forming of approximately 315 man-made mineral formations at the territory of the Sverdlovsk region. The region contain over 32.5 billion tons of barren rocks and out of balance ores, over 1.5 billion tons of tailings, over 115 million tons of slimes, and over 100 million tons of metallurgical slag (Demin et al., 2000). Latters, at average, contain 407 thousand tons of copper, 2519 thousand tons of zinc, 7 tons of gold, and 150 tons of silver (Rudoy et al., 2011). Wastes generated in mining processing and metallurgical sector of economy contain not only thousands tons of copper and zinc, but cause significant damage to the environment where they are located. The reduction of negative impact of anthropogenic wastes on the environment as well as the storage volume reduction of valuable metals from dump slags is possible by improving the efficiency of the melting and further flotation of slags formed during this process."

Jan 1, 2016

By L. J. Surges, C. Bazin, D. Hodouin

"A kinetic model was developed for the conditioning and flotation processes of an industrial lead concentrate dezincing circuit. The models were incorporated into a flowsheet simulator. Simulation results demonstrate the advantages of split conditioning of coarse and fine particles and the potential of this approach for the production of the heuristics required for the development of intelligent control strategies.The conditioning model relates the proportions of activated and hydrophobic surfaces and residual reagent concentrations to activator and collector reagent flowrates. The model accounts for the solids and water flowrates, and for the solids grade and size distribution. The flotation model uses the predicted proportion of hydrophobic mineral surface, the aeration rate and the froth depth to estimate cell, bank and circuit performances. IntroductionFlotation has been the object of modelling and simulation studies for more than two decades. The process is usually modelled as a kinetic one in which the particle flotation rate constants are key parameters. Rate constants are related to the operating variables (pH, reagent flowrates, aeration rate, etc), however these relationships are seldom established in the literature.In spite of the large amount of literature on flotation modelling and simulation, few papers deal with the interaction between flotation rate constants and operating variables. This important gap, which was identified in the early seventies by Woodburn (l970), still exists. One of the first attempts to include operating conditions in a flotation simulator was made by King (l973), who explicitly introduced the aeration rate into an air bubble loading model. Lynch et al. (1981) used an empirical model to relate the proportion of slow floating particles to the ratio of collector per ton of ore. Such empirical relationships are difficult to calibrate and cumbersome to use when an activator and a collector are added to slurries in which particle size distribution and surface characteristics are changing. Eascur and Herbst (l982) relate in a fundamental way the mineral flotation rate constants to the aeration rate, froth depth, agitation and frother concentration, however the model does not account for reagent flowrates. Niemi et al. (1982) have proposed a model for the conditioning of minerals and included it into a conventional flotation simulator."

Jan 1, 1988

By M. Hashemzadeh

The efficiency of water use is a top priority for the global minerals industry, especially in regions with limited freshwater supplies. In these areas, the freshwater shortage has prompted mining companies to search for alternatives to freshwater sources. Seawater has been proven to be a potential water source for mineral beneficiation and metal extraction processes. This study compares chalcocite leaching behavior with ferric chloride to that with cupric chloride. We carried out leaching tests with a highly pure chalcocite sample in jacketed reactors under fully controlled pH and solution potential. The effect of chloride concentration, oxidant concentration, and temperature on copper extraction was quantified in both cupric and ferric chloride systems. In the ferric chloride system, increasing ferric concentration showed a positive effect on the first stage of chalcocite leaching. In the second stage, increasing temperature markedly enhanced copper extraction. In the cupric chloride system, chloride concentration presented a considerable effect on both the first and second stages of leaching, while temperature had a remarkable effect only on the second stage. The findings of this study would be beneficial to mine operations aiming to replace fresh water with seawater for heap leaching of chalcocite. INTRODUCTION Mineral processing operations/plants are normally operated adjacent to mines which are often located in remote and arid area, such as northern Chile, southern Peru and Australia with limited access to fresh water (Liu, Moran, & Vink, 2011, 2013). Water scarcity in these areas has prompted mining companies to invest in sustainable technologies to reduce the water use and/or increase the water use efficiency. One of the current sustainable approaches in mineral processing operations is to replace fresh water with seawater. Seawater is now being increasingly used for mineral beneficiation and metal extraction processes (Hernández et al., 2015). Another application of seawater could be for heap leaching of copper secondary sulfides, mainly chalcocite. However, the high concentration of chloride ion in seawater may significantly affect leaching kinetics of copper sulfide concentrates and ores (Watling et al., 2014). Therefore, it is essential to develop a fundamental understanding of the leaching of chalcocite in chloride media.

Jan 1, 2019

By V. Labiouse, F. Orellana

"Hollow cylinder samples can be tested for both the characterization of rock properties and the physical modelling at reduced scale of engineering applications. Particularly, this type of experimental setup can be used to simulate different stress conditions around underground openings, as already developed in the petroleum engineering field e.g. to study the instabilities around deep wellbores during either drilling or the oil production phase. Some authors have also used this technique to successfully characterize the damaged zone around underground openings in the tunneling engineering field looking for an efficient design of their support.This article presents a new hollow cylinder testing device developed at the Rock Mechanics Laboratory of the Ecole Polytechnique Fédérale de Lausanne (EPFL), Switzerland. It allows a full and independent control of the confining pressure and pore water pressure conditions at both the inner and outer boundaries of Thick-Walled Hollow Cylindrical samples. In order to mimicking a tunnel excavation in a porous rock mass, after initial recovery of the in-situ stress and pore water pressure, the hollow cylinders are subjected to a decrease in the internal confining pressure. Moreover, X-Ray Computed Tomography scans of the specimens are performed through the testing cell before and after the mechanical unloading to monitor the displacements undergone and the sample damage. The equipment, testing procedure and data analysis techniques are briefly presented in the paper.The good performance of the apparatus has already been checked on weak rock specimens, among others on Boom and Opalinus Clay samples. In many configurations, the mechanical unloading is found to induce a Damaged Zone (DZ) around the central hole. Its geometry and extent show a great similarity with in-situ observations around tunnels driven in the Boom and Opalinus Clay formations. Such similarities contribute to increase confidence in the understanding and modelling of the ongoing processes."

Jan 1, 2015

By N. Molaei, E. R. Bobicki

The continued demand for mineral products, coupled with the depletion of high-grade ore resources, has led to the mining of lower grade ores, which often require fine grinding to achieve mineral liberation. Regrinding of low-grade ores results in the production of fine gangue mineral solids and produces vast quantities of fluid fine tailings which are difficult to separate from water, particularly if they are composed of clay minerals. Organic synthetic polymers and inorganic salts have been widely applied in flocculation of colloidal suspensions in the treatment of mining tailings. However, there are growing concerns regarding their impact on the environment and human health. Recently, extracellular biopolymer flocculants or bioflocculants have attracted much attention as alternative reagents. In this study, much effort has been devoted to considering the effectiveness of protein and polysaccharide-based biopolymers for the dewatering of clay slurries. The interaction between kaolinite and illite clays and biopolymers was investigated via settling tests at pH 7 and 10. Zeta potential measurements were also conducted as a complementary technique. Results showed that protamine and lysozyme protein- based biopolymers were generally the more effective bioflocculants. Pectin, a polysaccharide-based biopolymer, showed a dispersing effect and has the potential to be used as a dispersant and/or depressant for clay minerals in froth flotation. INTRODUCTION With the depletion of high-grade ore resources, the need for mining of low-grade ores has increased over the past few decades (Bourgès-Gastaud, Stoltz, Dolez, Blond, & Touze-Foltz, 2014; Chen, Walshe, Fru, Ciborowski, & Weisener, 2013; C. Wang, Harbottle, Liu, & Xu, 2014). Low-grade ores often require fine grinding and contain clay minerals, leading to the generation of fluid fine tailings (FFT). It is a challenging process to separate suspended clay particles from water (Craciun, Manaila, & Stelescu, 2013; Dompierre, Lindsay, Cruz-Hernández, & Halferdahl, 2016; Kasperski & Mikula, 2011; Mercier et al., 2012). Clay minerals form stable dispersions in water due to their anisotropic nature, non-spherical morphology and colloidal size (Lagaly & Ziesmer, 2003; Olphen, 1977). The difficulty in separating clay minerals from water has led to the accumulation of vast quantities of FFT in oil sands, phosphate, copper and nickel operations, representing a huge liability for mining companies (Chen et al., 2013; Mercier et al., 2012)

Jan 1, 2019

By W. B. Boggs

A paper describing the Noranda smelter was presented at the 1930 annual meeting of the Institute (1). A lacer article appeared in the Trans-actions of the A.I.M.&M.E. in 1933. Since that time there have been many changes and improvements in plant operation and it is the abject of this paper to give an account of developments up to the beginning of 1939. The Noranda smelter was built originally for a capacity of 30,000 tons a month. At present, the average tonnage being treated is 110,000 tons a month, the tonnage of custom ores alone amounting to almost the total rated capacity of the original plant. This increase has been accomplished by increasing the capacity of the reverberatory furnaces from 700 tons of solid charge per furnace day in 1928 to 1,500 tons per day at the present time. In 1935, it appeared chat the limit of furnace capacity had been reached at about 1,300 tons of charge per day because of the short life of the sprung silica arches. However, the adoption of the suspended magnesite roof, which had been developed at the Flin Flou smelter of the Hudson Bay Mining and Smelting Company, overcame this difficulty and it is believed that the limit of the capacity of the present reverberarory furnaces has not been reached. A brief account of the changes to equipment in the various departments will be given, followed by a description of the more important features of present smelter practice.

Jan 1, 1939

By W. A. Gow, V. F. Harrison, H. H. Mccreedy

A semi-continuous bench-scale, countercurrent-decantation system, in which the ore was moved countercurrently to the flow of leaching solution, was used to conduct acid-leaching tests on uranium ore with the aid of bacteria. This method, which involved a low degree of agitation, was successfully applied to extract uranium in practical amounts and at practical rates. The acidity of the leaching solution was the main variable investigated in the bench-scale tests done at the Mines Branch, Ottawa. Over 90 11er cent of the uranium was extracted in a six-stage system. The results suggest that this technique could be ap-plied in the utilization of bacterial oxidation and leaching as a method for treating Elliot Lake uranium ore.

Jan 1, 1969

WHAT IF? ?Mine closure and reclamation liabilities were fully funded -at all times from current mine revenues ?Unexpected & catastrophic events were insured ?Remediation costs could be capped ?Risk management was improved ?best practice and independent oversight ?Host communities?concerns were adequately addressed If this could be achieved within a cost-effective financial structure, this may be a solution to a complex issue for the mining industry

May 1, 2006

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By R. Salimi

Tricalcium aluminate hexahydrate (TCA) is used as filter-aid for security filtration in the Bayer alumina process. TCA is typically produced on-site by mixing Bayer liquor with slaked lime. Specific properties are required from the TCA to ensure adequate filter throughput, lifetime and importantly effective reduction of solid/colloidal impurities from the solution. The effect of reaction time on morphology and particle size distribution of tricalcium aluminate was studied for a batch experiment at simulated process conditions. It was found that reaction time plays a critical role on the morphology, crystal structure (diameter and crystallinity) and particle size distribution. In the early stages of the reaction, nucleation dominates the crystallization process followed by growth dominated by agglomeration up to a mean particle size of 10 µm. The particle morphology shifted from an irregular shape to more spherical throughout the course of the reaction.

Jan 1, 2014

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By Edward (Ted) R. Lord

The application of thickened/paste tailings for surface disposal has been practiced for many years but has recently started to gain wider international acceptance. With tailings ponds coming under increasing environmental scrutiny, there is growing momentum towards mine/tailings plans that greatly reduce the size or even eliminate tailings ponds completely. This paper provides examples from the author's own experiences of the application of thickened/paste tailings for surface disposal in different countries, under different climatic conditions and in different industries. The paper will also comment on current research initiatives and future trends.

May 1, 2001