Search Documents

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By A. McMullen

"IntroductionTHE LOW-VOLATILE bituminous coals of the Brazeau field, Nordegg, Alberta, are soft and weak in structure. The seams contain .bands of inferior material, locally designated 'black jack', and thin bands of friable carbonaceous shale having no definite horizon but usually 'floating' in the seam. Because of the weakness• of the coal and the friable nature of the shale bands, run-of-mine coal usually contains a very high percentage of fines, as •Shown in the following table:SIZE WEIGHT. %Plus 1/2 in 25.61/2 – 1/4 in 13.31/4 - 1/8 in 14.6Minus 1/8 in 46.5The most convenient way of cleaning the fine coal would be by treating it in association with the coarse coal, so that no additional plant would be necessary. To a limited extent this is possible in certain types of equipment, notably the jig. A system of washing without pre-sizing is not •attractive, however, when dealing with the friable coal under consideration, which contains •a preponderant proportion of fines. At the new Brazeau washery, separation is made at 3/8-inch on •a Robins 'Vibrex' •screen, the coarse sizes being cleaned in •a standard pulsator-type jig. A feldspar jig is used to clean the minus 3/8-inch fraction."

Jan 1, 1954

By A. R. Farkoosh, J-P. Fortin, M. Pekguleryuz, S. Bagherpour

"Titanium aluminides are structural intermetallics which offer an attractive combination of high temperature strength and light weight. For such properties, these intermetallic alloys have become front-runners in replacing nickel-based superalloys used for several high temperature applications. These alloys are produced from metallic titanium, aluminum and master alloys involving an expensive and difficult process. A low cost alternative to current industrial production method is the new modified aluminothermic process which directly reduces titanium oxide (TiO2) to titanium aluminides. Nevertheless, this process has itself significant challenges in achieving alloys free of oxide inclusions; the close densities of the slag and the titanium aluminides makes slag/molten metal separation a challenging task. Usually, the alloy produced requires a second refining step. In this study, thermodynamic calculations based on CALPHAD method were performed to determine the solidification path and an attempt has been made to develop a criterion to increase the density deference between the slag and the alloy by alloying with appropriate elements. Furthermore, scanning electron microscopy (SEM) and x-ray diffraction (XRD) techniques were utilized to examine the microstructure and phase selection of three Ti-Al alloys produced by the aluminothermic reaction, including the as-cast, refined in a controlled atmosphere and inert-gas-refined alloys. The composition range of the alloys studied was restricted to the a2-Ti3Al + ?-TiAl phase field (Ti-30Al) in the binary Ti-Al phase diagram leading to a lamellar structure with different complex intermetallics as shown in Figure 1.INTRODUCTIONTiAl based alloys are promising structural materials for high temperature aerospace and automotive applications. This is due to some attractive properties such as low density, high specific strength, high specific stiffness and high temperature strength retention (Wen-bin, Xue-wen, Hong-fei, & Yong-feng, 2011). These alloys have become leading candidates to replace Ni-based super alloys in gas turbine engines. Replacement of Ni-based super alloy parts with titanium aluminides is expected to reduce the structural weight of high performance gas turbine engines by as much as 20–30% (Kothari, Radhakrishnan, Sudarshan, & Wereley, 2012)."

Jan 1, 2016

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By Y. Chunhua, L. Chunsheng, W. Sheng

"Countercurrent solvent extraction is the dominant industrial rare earth separation method. For the rare earth separation, with low separation factors and multiple components, designing and optimization plays an important role in reaching product quality and reducing separation plant costs. Based on the theory of countercurrent extraction, cost-efficient methods, such as third-outlet separation and hyperlinked extraction processing, have been introduced following computer simulation. The consumption and fixed investment of industrial practice are compared, by which advantages of the optimized rare earth separation process are indicated. INTRODUCTIONThe rare earths (RE) have outstanding optical, magnetic and electric properties in advanced material applications and have therefore received much international attention in recent years. Liquid-liquid extraction is the major industrial RE separation method and is widely used in the industry. Supported by the government and with collaboration from the institutions and enterprises, China has made great progress in RE separation, and has become the dominant supplier of separated RE products. Complicated by multiple elements and low separation factors, careful design of RE separation processes is vital for the quality and cost of production. The theory of separation is the key to basic of flowsheet design and industrial applications.BASIC SEPARATION PROCESS AND THEORYGeneral ProcessAcidic extractants such as P507, P204 and naphthenic acid, are the most popular extractants in modern RE separation industry. In the general separating process, the extractant is saponified with a base, then ion-exchanged with RE solutions, thereby to provide stable and high RE loading in the extractant to fulfill the requirement of production quantity and quality. The RE-loaded extractant is then countercurrently extracted and scrubbed with RE solutions and the RE element thereby is purified. After the countercurrent extraction process, the RE-loaded extractant is stripped with acid to obtain an aqueous RE product, and prepare the extractant for recycling (Xu, 1995)."

Jan 1, 2012

By S. Hunt, S. Jayasekera, J. Kyle, N. Perera, K. Stone

A preliminary investigation has been conducted to determine the conditions for the precipitation of phosphate from the liquor produced after a hydrochloric acid pre-leach and rare-earth recovery from a rare earth containing fluorapatite concentrate from the Nolans rare earth deposit in the Northern Territory of Australia. The results show that at 50oC the phosphate can be precipitated in two stages using limestone to produce a Stage 1 precipitate containing most of the impurities including iron (94%), aluminium (92%), fluoride (98%), uranium (84%) and thorium (94%), followed by a relatively pure Stage 2 dicalcium phosphate precipitate (DCP) containing only 0.05% Fe, 0.05% Al, 0.1% F, 0.01% U, and <0.01% Th. The initial Stage 1 precipitate contained about 25% of the phosphate while the remaining 75% reported to the Stage 2 phosphate precipitate. Depending on the required radioactivity specifications, the amount of phosphate in the Stage 1 precipitate could be reduced. Reagent requirements were 11.4 kg limestone (as pure CaCO3) per cubic metre of solution for the Stage 1 precipitate and 39.7 kg limestone (as pure CaCO3) per cubic metre for Stage 2. The analysis of radionuclide balance indicated that radionuclides deported mainly to the final filtrate (86.4%) compared to Stage 1 precipitate (5.4%) and Stage 2 precipitate (8.2%). Settling and pressure filtration tests indicated the precipitates were both readily settled and filtered. The final moisture contents of the Stage 1 and Stage 2 precipitates were 62.5% and 49.3%, respectively.

Jan 1, 2014

By F. Tanaka

Copper losses to discard slag have long impacted on the profitability of copper smelters. Businesses based on the treatment of secondary materials have also revealed that copper losses are indices of precious-metals losses. Many custom smelters are thus required to obtain more reliable controls for reducing copper losses than ever before. Mitsubishi Materials Corp. has cooperated with academic research institutes in conducting research projects on the pyrometallurgical fundamentals of copper smelting systems, including mutual evaluation of magnetite behavior between synthetic and industrial slags. The state-of-the-art pyrometallurgy has subsequently been introduced to Naoshima smelter for controlling the Mitsubishi process. The revised controls function successfully and the operational results demonstrate that avoiding the discharge of solid magnetite from the S-furnace is quite effective to reduce copper losses. Magnetite behavior has been controlled over the Mitsubishi process so as to reduce copper losses while satisfying the needs of recycling businesses growing in Japan. In-situ estimation of magnetite behavior using the absorbed heat from the melts to cooling water will also be discussed.

Jan 1, 2007

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973

By N. Dobrin, R. Sheinman, Y. V. Kokotov, L. N. Braginsky

Increasing the production of a Mixer-Settler unit requires either increasing flow rates or increasing extractant concentration. The mixers still have to ensure complete emulsification and to maintain high values of specific interface surface area in order to provide a high rate of mass transfer. Theoretically, an increase in mixing intensity can support increased flow rates without reducing extraction efficiency. Unfortunately, conventional pump mixers and mixing systems create small droplets that do not separate easily. As pumping action and mixing intensities are increased, the quantity of small droplets increases. We describe the development and industrial application of a novel mixing system for efficient mass transfer without forming significant quantities of small droplets, targeting both high mass transfer rate and low entrainment values.

Jan 1, 2014

By L. E. Gutiérrez

A new filtration model based on porous media transport theory is presented. It predicts capacity and final moisture content in the filtered cake as a function of design and operational variables at the plant. FilterSim® is the computer code where this new model is programmed. Application of FilterSim® to ten-month operation of an industrial copper concentrate filtration plant is shown on a daily basis and using a single set of internal parameters for the whole period. Average error is less than 5%, both in capacity and moisture estimation. FilterSim® abilities to optimize industrial filtration plants as well as to estimate future budgets are illustrated with several real examples.

Jan 1, 2007

By Christian Brits, Bob Blain, Lloyd Buckingham, Juliu Stieger, Jean-Francoi Dupont

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By F. S. Thurner

This paper, a description of the new ore-unloading and stockpiling facilities at the Sydney Works of DOSCO Steel Limited, deals with a new approach to arrive at the most economical solution to combine ore unloading facilities for common bulk carriers and for different types of self-unloading vessels. Also discussed is the design and installation of a 1-mile-long steel-cord belt conveyor sys-tem with a most modern type of mobile belt conveyor stacker, along with automatic and semi-automatic controls for the entire ship-unloading and stockpiling operations.

Jan 1, 1968

By G. P. Kundargi

India is one of the fastest growing economies in the world. The role of the Iron & Steel industry is very important for the development of the country. Iron and steel are among the most important components required for the infrastructure development of the country. This is one of the fastest growing sectors. The demand drivers for the Indian Iron & Steel industry are increase in the activities of the manufacturing industry and infrastructure development. Indian Iron & Steel industry with its strong forward and backward linkages contributes significantly to overall growth and development of the economy. The industry today directly contributes 2% of India?s Gross Domestic Product and its weightage in the official Index of Industrial Production (IIP) is 6.2%. Manganese is a main ingredient for production of steel. Almost 90% manganese is being utilized by the steel industry worldwide. Globally, there is no substitute for manganese as on date. There is huge gap between demand and production of manganese ore in the country. To meet this demand gap and to support for growth of national economy, MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprises, producing annually around 1.1 million tonnes (mt) of manganese ore and value added products, has geared up with various infrastructural activities to increase the present production capacity of 1.1?1.5 mt in 2016?2017 and 2.2 mt in 2020?2021. The paper deals with the technological improvements and infrastructural development activities of MOIL; this will help MOIL to become the market leader in manganese ore production globally in the coming years.

Aug 1, 2013

By M. Kowalczyk

The successful application of color sorting machines has established sensor-based sorting in the mineral industry in recent years and is considered today as a significant innovation in processing technology. However, we are only at the beginning of the (market) introduction. New sensor systems have been developed, which exploit material properties such as electrical conductivity, magnetization, molecular structure, thermal conductivity etc. This opens up new exciting pre-concentration and upgrading possibilities for many applications such as nickel, gold, copper and other ores as well as for industrial minerals, diamonds and other gemstones.

Jan 1, 2009

By H. Miki, S. Wheatley

The addition of precipitated silica greatly enhances chalcopyrite leaching in the presence of sodium chloride at moderate temperatures (65-90°C) in acid media with ferric ions as the oxidant. The beneficial effect increases with the increase in chloride concentration and temperature. The addition of sodium silicate and silica sand has no significant influence. The analysis of solubility data in acid/salt solutions indicates that the solubility of silica as Si(OH)4 as the dissolved species is controlled by the activity of water, as expected from the hydration theory. Kinetic analysis shows the trends that copper dissolution from chalcopyrite in the presence of precipitated silica with sodium chloride follows a shrinking sphere model indicating a chemically controlled surface reaction. The effect of temperature on copper dissolution in the presence of both precipitated silica and sodium chloride was also larger compared to the results in sodium chloride alone. The SEM analysis shows that chloride and silica facilitates the precipitation of sulfur on the surface of the silica particles rather than the chalcopyrite particles which avoids the blockage of the mineral surface and thus improves the leaching kinetics.

Jan 1, 2014

By D. Y. Kim

This paper shows an approach that a gondola-typed robot recognizes walls on building facades. It is applicable for autonomous or teleoperated building façade painting robots. The robot may react based on the wall classification data. This approach is based on 2D LRF(two-dimensional Laser Range Finder). The robot acquires relative distances to walls, and a Kalman filter decides correspondence of walls. An ARS(Attribute Reference System) sensor helps convert LRF coordinate to global coordinate. The experimental results demonstrate the conversion of LRF data.

Aug 1, 2013

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l&apos;horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l&apos;ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d&apos;âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu&apos;un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d&apos;un km au nord des chantiers souterrains, fut découverte vers la fin de l&apos;année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L&apos;amin­ cissement des roches pourrait être primaire ou être le résultat de l&apos;atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d&apos;une zone de sulfures indique un potentiel énorme pour la découverte d&apos;autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By G. Kipouros, M. Dadvand, A. Dadvand

"A novel methodology was developed to obtain a 3D porous layer with a high aspect ratio of porosity on a titanium electrode. The porous structure allowed more active material such as hydrous ruthenium oxide to be accommodated during the fabrication of the supercapacitor, resulting in an exceptionally high capacitance per surface area. The electrode demonstrated a remarkably high capacitance of 4,800 mF/cm2. The porous layer was composed of functionalized nanoparticles of TiO2 organized in a perfect 3D hexagonal close-packed array that resulted in a highly porous 3D structure. The layer was used as a template to electrolessly deposit a thin layer of silver prior to the electrodeposition of active material. KEYWORDS Capacitance, Porous, Ruthenium, Silver, Supercapacitor, Titanium RÉSUMÉ Une méthodologie innovante a été mise au point afin d’obtenir une couche poreuse tridimensionnelle (3D) affichant un rapport d’aspect élevé en termes de porosité sur une électrode en titane. La structure poreuse permet d’utiliser une matière plus active telle que l’oxyde de ruthénium hydraté durant la fabrication du supercondensateur, ce qui se traduit par une capacité exceptionnellement élevée par surface active. L’électrode affichait une capacité remarquablement élevée de 4 800 mF/cm2. La couche poreuse était composée de nanoparticules fonctionnalisées de dioxyde de titane (TiO2) organisées dans un arrangement regroupé parfaitement hexagonal en 3D, qui a engendré une structure en 3D hautement poreuse. Cette couche a servi de modèle pour le dépôt autocatalytique d’une fine couche d’argent avant l’électrodéposition de la matière active. MOTS CLÉS argent, capacité, poreux, ruthénium, supercondensateur, titaneINTRODUCTION There is a growing demand for integrating compact energy storage elements into electronic circuits due to the miniaturization of electronic circuits, sensors, and actuators, and the increasing importance of portable and wear-able devices incorporating more advanced electronic technologies that operate in controlled or uncontrolled environments to gather, process, store, and communicate information (Deng, Ji, Chen, & Banks, 2011; Beidaghi & Wang, 2012; Chen, Ramachandran, Mani, & Saraswathi, 2014). The manufacturing of compact energy storage elements needs to be compatible with the electronic circuit microfabrication processes. Recently, interest in integrating miniaturized supercapacitors into electronic circuits has increased due to their high charge–discharge rate and long operating life; however, ultra-high power miniaturized supercapacitors suffer from low energy density, hence requiring significant enhancement in their energy density for various applications (Deng et al., 2011; Beidaghi & Wang, 2012; Chen et al., 2014)."

Jan 1, 2019

"Dry crushing trials at pilot scale have shown that the IMPTEC Super-fine Crusher has the capacity to generate ultra-fine products from hard mineral assemblages presenting at either coarse or fine feed sizes. The super-fine crusher was introduced at the 27th International Mineral Processing Congress in Santiago Chile, with results from a range of duties, which demonstrated the crusher’s potentially expansive operating scope. This paper focuses on current preparations to progress the technology from pilot scale to commercial scale within a concrete production plant, where lead blast furnace slag will be crushed to ultrafine sizes to generate an active silica product for use as a supplementary cementitious material, which can replace Ordinary Portland Cement. A key objective of the operation is to demonstrate an economical route to reducing the cost of concrete production, improving concrete quality and reducing greenhouse gas emissions. The paper also highlights the potentially key contribution super-fine crushing can make to the long-term viability of iron ore beneficiation by simplifying comminution flow-sheets and reducing operating costs. There is every indication that the technology has the potential to feature universally in metalliferous and industrial mineral flow-sheets. INTRODUCTIONToday’s IMPTEC super-fine crusher is the successful end product of development work over 19 years and is the third particle size reduction device conceived, built and tested over that time. The concept evolved as engineering design progressively developed a mechanism capable of harnessing a highly efficient combination of fundamental particle breakage mechanisms. Early development trials at pilot scale indicated that super-fine crushing had the potential to establish a wet or dry, media free, low energy route to ultra- fine products from hard mineral assemblages. Having achieved some impressive results from open circuit pilot tests on fly ash and granulated blast furnace slag it became clear that the cement industry may well provide opportunities to apply the technology commercially. Following expressions of interest from local cement and concrete plant operators, IMPTEC negotiated an agreement to undertake commercial trials with a SFC 350 super-fine crusher installed on site at a concrete supply plant in South Australia. Super-fine crushing scope was recently expanded following further expressions of interest from research groups involved in the processing of iron ores. Pilot trials are progressing in these areas."

Jan 1, 2016