Search Documents

By R. J. A. Fricker

IT is the purpose of this essay to give a reasonably complete description of shaft sinking under a rock pentice in a small Northern Ontario gold property. Hallnor is in many ways an exceptional mine, but the sinking operations here described are but typical examples of the excellent practice for which Canadian mines and mining engineers are justly famous the world over. The worth of the subject lies, therefore, nor in its originality, but in its soundness; not in the spectacular, but in the economical and safe. Attention is particularly drawn to the excellent safety record and to the exceptionally low overall sinking cost. INTRODUCTION Prior to April, 1939, the Hallnor No. 1 shaft had been sunk vertically to a depth of 997 feet below the surface. It is a three-compartment shaft, 19 ft. 10 in. by 7ft. 7 in. outside the timbers (see Figure 1).

Jan 1, 1941

By S. A. Bradford

The twenty years before World War I was the Golden Age of copper smelting in British Columbia. In this short time, the smelters developed from small, primitive units to large, efficient operations. The first copper claims had been staked on Howe Sound and Knight Inlet in 1864, and there was extensive copper mining in the interior by the mid-1880s, but before 1895, all ore was shipped out of the country for smelting, converting and refining. The first interest in smelter construction was undoubtedly inspired by a Provincial bonus and Dominion land grants offered to smelter builders. The early smelters made use of small blast furnaces which were designed to smelt any kind of ore, but usually far too little ore was available. The first smelter seems to have been the McRae furnace on the Spillimacheen River (1883), followed by Vancouver (1889), Revelstoke (1891), and Golden (1891) (1). They each smelted a few tons of galena and then quickly closed down permanently for lack of ore. Only smelters that actually produced some copper matte are described in the following sections.

Jan 1, 1999

By T. Tsutsumi, S. Kukino

"During the diametrical compression test, the tensile stress generated near the loading plate is influenced by the contact area between the loading plates and specimen. However, very few studies have determined the contact area. Theoretical or analytical models have shown that for an orthotropic material (i.e., with material properties that differ along each of three mutually orthogonal twofold axes), the maximum tensile stress is generated at the center of disk when the angle of the principal material direction to the loading direction is close to ?/4. The maximum value is almost constant, regardless of the contact area. Conversely, the maximum tensile stress is generated near the loading plate when the angle between the principal material direction and loading direction is small. The maximum value decreases as the contact area increases. Therefore, in the latter case, the influence of the contact area on tensile strength measurement of is significant.In previous studies, the distribution of stresses applied on the loading plate is assumed to be a uniform load. In reality, the applied stress is highest at the center of loading plate and seems to decrease with distance from center. The applied load disappears at the edge of loading plates. In this study, in order to satisfy this boundary condition on the loading plate, the cosine curve is adopted as the distribution of load applied on the loading plates in a theoretical model of the diametrical compression test. Furthermore, the elastic solution using boundary conditions shown in this study is used to obtain the tensile stress distributions on the loading axis for an orthotropic circular plane. These distributions are compared with empirical results obtained under uniform loading with a loading plate or concentrated loading in previous studies."

Jan 1, 2015

By LUKE O. LINDOE

A major clay products industry in the Medicine Hat area since before 1910 has maintained a continued interest in the clays of the Cypress Hills. For the first forty years the materials used were local red-burning Cretaceous and Pleistocene clays and sands and high-quality stoneware clays of the Whitemud Formation at Eastend, Saskatchewan. Recently a much broader spectrum of raw materials has been brought into use. Including the exposures of the Eagle Butte structure, the Cypress Hills present a 1200 m section of clay-like sediments. Of this 1200 m about 94 per cent, the high montmorillonite shales of the Upper Cretaceous, can be considered useless, or nearly so; the remaining six per cent, all fresh-water beds, presents a wide variety of potentially useful materials. The development of these clay resources is complicated by deep surface creep on the south flank of the Cypress Hills, by largescale slumping on the north flank and by a structural complex in the Eagle Butte area.

Jan 1, 1984

By G. O. Crowell

This paper gives the history of the celestite deposit, now being mined by Kaiser Celestite Mining Ltd., near Sydney, Nova Scotia. Mining and milling procedures are covered, and the regional and local geology of the area are described, including the origin of the celestite.

Jan 1, 1971

By Lan Vu

"The Ferderber mine consists of a series of Archean gold-bearing quartz lenses within a shear zone that crosscuts the central part of the quartz diorite Bourlamaque batholith. This zone has sharp contacts with the enclosing quartz diorite, and on average strikes N70E and dips 65SE. Along the contact with the shear zone, the quartz diorite is chloritized, sericitized and carbonatized. The chlorite schist within the zone is probably derived from mafic dykes.The geometry and distribution of structural features within the Ferderber shear zone suggest a long history of repeated movements. The majority of gold-bearing lenses were first emplaced during a probable early period of brittle shear which resulted from strike-slip movement. They were then folded and pulled into boudins by a later episode of reverse movement that accompanied ductile shear. New mineralized veins were emplaced in the shear zone and deformed at this time.Mineralized veins are dominated by quartz, carbonates, tourmaline and micas. Gold is more common within pyrite where chalcopyrite is abundant and is generally in contact with both pyrite and chalcopyrite at ""triple point"" grain junctions. This intimate association suggests that copper may have played an important role in gold deposition.Recent exploration has shown that the Bourlamaque batholith is cut by many parallel or en echelon shear zones. Study of ""Landsat"" and aerial photographs has indicated a number of linear structures striking ENE-WSW and ESE-WNW which form a conjugate system. The intersection of these two structural trends presents an interesting exploration target."

Jan 1, 1990

By Gareth Barnes

Traditional approach to improvement is driven by good ideas from good people, but whilst the business case may sound good, when the project is complete, we often have not delivered on expectations.  Why not? The best way to successfully predict the outcomes of an improvement effort in a complex process is through using statistical modelling, which considers the impact of uncertainty within interacting processes.  Applying Theory of Constraints in a model helps leaders to quickly determine: Where the constraining process(es) is/are Where improvements will add the most value How much improvement should be targeted - before the next constraint takes over The confidence level of achieving a given target, which gives us a clear pathway to improvement. This paper presents an analysis of statistical modelling applications at Vale’s Manitoba Operations to achieve the 2025 targets. Using statistical modelling of the Business Structure, the team identified a series of process improvements through a Theory of Constraints Analysis. Value Stream Maps (VSMs) were used to define the required data, apply statistical modelling, and conduct training sessions enabling the Manitoba team to identify the constraining influences. Scenario testing in the Statistical models helped identify the Hierarchy of Constraints and specify the pathway to improvement. How to Improve a Business Video link https://vimeo.com/344418155

May 4, 2025

By George Dogbe

Open pit optimization forms the basis of mine design, production planning and construction of mine facilities. The negative effects of this phase may include substantial reductions in ore recoveries, relocation of waste dumps and surface infrastructure, extraction of unwanted waste, with a cumulative effect on mine value reductions. As a result, this area has received significant research focus using linear and dynamic programming, heuristic, genetic and stimulation algorithms and the graph theory. These algorithms are derived from rigorous mathematical models, but they are built on the assumption that all the periodic production capacities are extracted at the time of analysis. This assumption weakens the models because mining occurs over significant time period. In order to develop a comprehensive model that accounts for the timing of material extraction, the current models, which are built on the economic block value (EBV) concept, must be modified to account for time. In this paper, the authors develop a model of the optimization problem using the 2-D Lerchs-Grossmann?s optimization algorithm. This model is used to investigate the effect of periodic discounting on the optimal pit layout design by designing an integrated pit optimiser (IPO) that incorporates ?production scheduling?. IPO uses the ensuing discounted economic block value (DEBV) as a basis for the pit optimisation process. The time-dependent model is compared with a time-independent model. The results show that discounting has no effect on the optimal pit contour although the reported pit value is overstated if the EBVs are used instead of the DEBV. The authors, however, believe that this conclusion may not be general and could have been influenced by the nature of ore body geometry and the proposed mining strategy.

May 1, 2004

By Glen Robertson, Jeff McLaughlin

"The Clarabelle Mill rock tailings have the potential to generate sulphuric acid through chemical and biological oxidation of sulphide minerals. Current rock tailings assay between 0.80 -1.40 %S, with sulphur occurring principally as coarse pyrrhotite. Acid generation within the tailings area can be substantially reduced by segregating pyrrhotite rich tailings in a submerged storage area and by depositing only low sulphur rock tailings in exposed areas. Laboratory tests confirmed that low sulphur tailings could be produced by flotation at reduced pH with a small xanthate addition. A plant test was conducted to evaluate the production of low sulphur tailings in conjunction with INCO's continuing commitment to environmental protection and progressive decommissioning of the metallurgical site.During the plant evaluation, approximately 5% of the mill rock tailings were reprocessed in a line of 100 tt3 Denver flotation cells. Tailing grades below 0.40% S were easily achieved through operation at pH 6 -7, with xanthate addition (dosages up to 0.02 lb/ton) and 10 -15 minutes of nominal retention time. Froth depths between 1 -3 inches combined with relatively liberal amounts of frother were required to pull the lightly mineralized froth into the concentrate which averaged 11% sulphur and less than 5% mass recovery. In addition, three field lysimeters were each filled with two hundred.ton bulk samples of low sulphur tails (0.35% S), standard rock tailings (0.98% S), and mill total tailings (2.30% S) for long term monitoring. The implications for full scale plant design, tailings area decommissioning, the possibility of increased nickel recovery and preliminary field lysimeter data are discussed."

Jan 1, 1994

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By J. W. Gregg, P. M. Dranchuk, D. L. Flock

"From preliminary investigations it has been observed that although evaporation losses may be estimated by comparing single values of certain physical properties of crude oils and their evaporation residues, such techniques possess little accuracy unless both the evaporation process and the variation of the property as a function of the process are completely known. The accuracy of estimation may be increased somewhat through the comparison of property mid-per-cent curves. Further increases in accuracy are possible if bottoms yield •curves rather than mid-percent curves are used. The use of both the mid-percent and bottoms yield curves however involves a prohibitive amount of effort in most cases. Examinations of distillation bottoms from Hempel type distillations carried to end points just short of the cracking point have indicated that these bottoms are not appreciably affected by the evaporation process. It was further observed that bottoms of identical API gravity, obtained from a crude oil and its evaporation residues behave as if they were pure components which were unaffected by evaporation. Based on these observations Hempel distillation bottoms of equal API gravity were obtained for a crude oil and its various evaporation residues from API gravity bottoms yield curves. The volume percent of these bottoms in the crude oil and its residues were used to calculate the evaporation losses suffered by the crude in order to yield the various residues. The results indicate that, although further refinements in technique are required, it is possible to calculate evaporation losses with an accept-able degree of accuracy through the use of this method."

Jan 1, 1960

By Abdelhak Bentriou

The choice of tool for the first well of an oilfield or gasfield is an important factor, given that we will be drilling with the same type of tool for the entire phase and explains why we need to have another type for comparison based on the efficiency of the tool and its ability to crush the rock, and the wear of different types of tools. Development of theoretical and practical tests to determine the optimal regime for drilling is required to take into account the characteristics of rock layers crossed. Classification of boring tools is based on the geometry of the teeth and depends on the hardness, the abrasiveness of rocks as well as their hydraulic system, but it is better to classify them according to the working conditions with a coefficient designating a discriminant. This is called physical characteristic of the drilling tool. The goal is to designate each element of the tool by a coefficient. Results were obtained from laboratory tests. Modeling the initial rate of progress by different types of tools allowed us to determine an adequate mathematical model of the speed initial progress in clean conditions. Using experimental data and statistics we have established the mathematical model of the average speed of progress as a function of time. With these equations we can determine the wear evaluation and analysis of these factors as an approach to classification according to their characteristics. The main equations for the selection of drilling tools will be based on the optimization of drilling parameters for each type of tool. After analysis, we choose the tool that gives a better forward speed with an optimal load and axial rotation.

Aug 1, 2013

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By John Hansen

This paper has been written for presentation at the 103rd Annual General Meeting of the Canadian Institute of Mining, Metallurgy, and Petroleum, April 29 to May 02, 2000. The paper addresses blast pattern fragmentation and diggability versus the blasting technique used. RESUME The author is the Vice President for Thunderbird Mining Systems. In this capacity he manages the mine site installation of surface mining mobile equipment monitoring and navigation systems. These systems are onboard instrumentation and software systems designed to: ??measure and log mobile equipments? production and health; and ??direct the equipment operators via onboard displays that show comprehensive maps and engineering instructions. The author is a mining engineering graduate from the Royal School of Mines. His work experience includes front line supervisor and mining engineer for Hudson Bay Mining & Smelting, mining engineer for Teck Corporation, and mining consultant for PriceWaterhouseCoopers.

May 1, 2001

By Gonzalo Díaz, Diego Mesa, Willy Kracht

"It is well known that frothers affect the amount of water that is transferred to the froth, which has an effect on both the froth stability and the water recovery. On the other hand, since non-selective recovery by entrainment is directly related to water recovery, it can be said that frothers have an indirect effect on flotation selectivity. Recent research on this subject has shown that the non-selective recovery by entrainment, which is characterized by the entrainment factor, is frother dependent. In other words, the entrainment factor is not unique, but depends on frother type.Having different entrainment factors implies that for the same water recovery, the amount of undesired particles reporting to the concentrate may vary if one changes the frother type, which suggests, as a possible explanation, that it is not only the amount of water in the froth what is affected by frother type, but also the froth structure.The purpose of the current work is to study the effect of frother type on foam structure (two phase froth). A quasi-2D cell operated with a slot sparger was used to study the foam structure in the presence of three different frothers: Methyl Isobutyl Carbinol (MIBC), OrePrep®549, and Octanol at the same gas flow rate and reagent dosage. The foam structure was studied using image analysis, and an algorithm based on textural analysis was developed to classify the foams. The results show that it is possible to classify foams according to the frother used, which proves that frothers have an effect on the foam structure.INTRODUCTIONFrothers are usually dosed paying attention to froth stability, condition that is commonly estimated by sight, according to the operator's criteria and experience. This happens because there is not an established procedure or technique for frother characterization, generating qualitative descriptions such as “powerful” or “selective” frothers, which lack of scientific thoroughness and remain under subjective factors. Nevertheless, several works have been done in this line of research. Moyo et al. (2007) classified frothers based on their water-carrying capacity, proving that this characteristic is related with gas holdup and frother type. Previously, Trahar (1981) had related water recovery and gangue particles recovery, defining the entrainment value (ENT). Nowadays it is known that entrainment affects both hydrophilic and hydrophobic because it is not a selective process. In the last decade some studies (for example the one of Konopacka and Drzymala (2010)) delved into different entrainment behaviours dependent mainly on the flotation type (batch or continuous, agitated or columnar, etc.), but there were no studies on the effect of frother type regarding entrainment, since Rahal et al. (2001) argued that the ENT factor was independent of the frother type and concentration, and froth height."

Jan 1, 2016

By Donald A. Cranstone

Donald Cranstone holds B.Sc. (Honours) and M.Sc. degrees in Geology from the University of Manitoba and a Ph.D. in Economic Geology from Harvard University. He has worked as a mine geologist, a provincial geological survey geologist and as a senior exploration geologist. He joined what is now the Minerals and Metals Sector of Natural Resources Canada in 1971, where he has been a commodity specialist for gold, for copper and another 28 metals. He is a senior mineral economist, currently engaged in analysis of mineral exploration and discovery success in Canada and of the future of the Canadian mining industry. Abstract This paper examines the history of Canadian non-petroleum mineral production. The outlook over the next 25 years, for mining in Canada and in each province and territory, is reviewed. The outlook for mining in Canada and in most provinces/territories is favourable, but problems seem likely in a few jurisdictions unless new orebodies are brought into production. In terms of exploration potential, Canada consistently ranks among the top three countries in the world. Over the last eight years, Canada has consistently been second only to Australia as a destination for exploration investment. For the first time, Canada is ranked in terms of total mineral production, including coal and construction materials, relative to all the countries of the world including countries of the former communist bloc.

May 1, 2001

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By P. Duran

The metallurgical gas handling system at Chagres Smelter, like that of many smelters, can be the limiting constraint to processing more concentrate through the smelter. Mass and energy balances for the metallurgical gas handling system processing off-gases from the flash furnace and Peirce-Smith converters have been used by both operations and process engineering groups to help evaluate different operational scenarios in which the use of the installed capacity could be maximized and/or an operational strategy can be change with the purpose of removing a bottleneck or justifying an investment to relieve a constraint in the gas handling system. The present work describes the development of these process balances that were carried out in Exce®. The results were validated with operational data and, subsequently, some cases of industrial interest were simulated, detecting some conditions that were limiting the operation due to the present installed capacity in the Chagres Smelter.

Jan 1, 2007

By Michael L. Free, Shukla. Abhijeet

The short-circuiting tendency of a copper electrowinning cell (EW) based on the roughness of cathode deposits was investigated with varying parameters such as Cu concentration, guar concentration, current density, and temperature. A bench scale EW cell was set up to produce copper under conditions similar to industrial Cu EW. In addition, a statistical analysis and finite element analysis were performed to analyze the deposited thickness, surface roughness and maximum feature height. Interaction data for the cathode deposits suggest that current density and Cu concentration together affect the roughness of deposit more than the combined effect of guar and temperature. Model predictions of roughness were similar to experimental values. The predicted time to short-circuiting was similar to the measured time. This study provides an industrial relevant baseline against which new operating parameters can be compared.

Jan 1, 2014

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008