Search Documents

By Joo Hyun Park, Hyun-Sik Park

"Gold is one of the most valuable and precious metals. But, the extraction efficiency of gold from natural resources is very low and labor-intensive due to very low concentration of gold, i.e.,1–5 ppm, which means that gold extraction processes produce extensive amounts of tailings. The gold content in printed circuit boards (PCB) from waste mobile phones is about 100 to 400 ppm, which is enormously greater than the concentration found in natural ores. Consequently, processes for recycling waste PCB and gold mine tailings become of increasing importance to maintain a sustainable society. As processing these waste materials by pyrometallurgical methods has become more economically attractive, understanding the thermodynamic behavior of gold in smelting slags under oxidizing and reducing conditions has become increasingly important. Therefore, in this study, the effects of slag chemistry, oxygen potential and temperature on gold solubility in smelting slags are discussed. From the results presented, the predominant species of gold is strongly dependent on the basicity of slag. Furthermore, more basic slags showed higher solubility of gold at a given oxygen partial pressure, and more oxidizing atmospheres enhanced the dissolution of gold to the molten slag phase. As a consequence, careful control of the slag composition during pyro-processing of gold-containing waste materials is required to maximize gold recovery. INTRODUCTIONGold has good physicochemical properties. Thus, it plays an increasingly important role in industrial applications. For example, over 300 tons of gold are used annually in electronic components (Hageluken &Corti, 2010).However, 75% of all gold ever produced has been extracted since 1910 and gold reserves in the world are becoming rapidly depleted (Louis & Pluchery, 2012).The cost of gold production and its price in the market have increased rapidly during last 20 years as shown in Figure 1, and interest in the recycling of gold-containing materials has naturally increased.The wastes from electronic equipment (e-wastes) contain large amounts of precious metals compared to their own respective ores, and therefore such wastes may be considered as a secondary source of valuable metals. For instance, the concentration of gold in natural ore is commonly 0.5–15 g/ton-ore (0.5–15 ppm), while its concentration in electronic circuit boards is over 10 times higher, typically being about 150 ppm in expansion cards and over 10,000 ppm in central processing units(Barbieri et al., 2010).Also, gold mine tailings are discharged after the flotation process as slurry form then stored near the operating plants (approx. 100 ton per day in one Korean gold mine). Gold mine tailings contain gold at about 1–2 g/ton. This is the reason why Au-containing materials such as e-wastes and mining wastes are highly important sources of gold (Yamasue et al., 2009)."

Jan 1, 2017

By Pierre Sauvé, Guy Perrault, Armand Savoie, Pierre Trudel

"La Mine Doyon est une entreprise détenue à parts égales par Cambior Inc. et par Minerais Lac Ltée qui en est l'opérateur. Les statistiques de production au 1"" janvier 1990 indiquent que, depuis le début de son exploitation (1980), 10.3 Mt de minerai d'une teneur moyenne de 5,9 g Au/t ont été usinées. Les réserves sont estimées a 10,4 Mt à une teneur moyenne de 6,6 g Au/t jusqu' à une profondeur de-450m.Trois zones minéralisées sont présentement en exploitation. Ces zones sont caractérisées par la présence de veines de quartz-pyrite accompagnées localement de chalcopyrite. Les roches encaissantes sont les schistes a séricite (zone# 1), les roches volcaniclastiques de composition felsique (zone #2) et intermédiaire (zone #2, zone ouest) ainsi que les roches intrusives appartenant au pluton de Mooshla (zone ouest). Toutes ces roches ont subi un métamorphisme régional dont l'intensité correspond à la limite supérieure du facies schiste vert ( -425°C}.Les zones minéralisées sont situées à I' intérieur des zones de déformation et d'altération les plus intenses. L'étude des structures mineures nous indique que la région a subi plusieurs épisodes de déformation ductile a fragile qui sont antérieurs, contemporains et postérieurs al a minéralisation. L'analyse structurale indique également que la déformation majeure est associée à une importante phase de compression orientée N-S a NNE-SSW.L’ensemble des observations suggère que la minéralisation et I' altération associée sont de type épigénétique. La mise en place du minerai se serait effectuée à la fin de l'épisode principal de métamorphisme et de la déformation."

Jan 1, 1990

By Rodney Trevor Jones, Arthur Robert Barnes

Anglovaal Minerals acquired the Nkana slag dump from Zambia Consolidated Copper mines (ZCCM) in 1998 and embarked on an ambitious project to pioneer the recovery of cobalt from slag using DC smelting technology. Anglovaal Research Laboratories performed initial pioneering smelting tests in a 250 kW DC furnace over a 3-year period before engaging Mintek for three piloting campaigns at the 1.5 MW level. Mintek had previously developed a reductive smelting process, patented in 1995, using a DC arc furnace for the recovery of cobalt from slags. The results of the pilot-plant test campaigns were used as the basis for engineering the commercial 40 MW operation installed at Chambishi Metals plc in Zambia in 2001. This paper traces the development of understanding of the metallurgical fundamentals ultimately used to predict furnace performance, reviews some of the extreme technical challenges faced, how solutions were identified and highlights some of the critical issues identified during piloting and how these impacted both positively and negatively on the final commercial operation.

Jan 1, 2011

By Suzie Poulin, N. Geoffroy, G. P. Demopoulos

Most metallurgical industries generate toxic waste that must be treated prior to being released to the environment. However, in a lot of cases, the waste materials are poorly characterized or the analytical results are not well interpreted. These shortcomings often result in the development of inefficient industrial procedures, thus causing economic waste and difficulty meeting environmental regulations. Fortunately, a wide range of analytical techniques are available to guide researchers and engineers into making sound process development decisions. In this work, an industrial selenium and mercury removal process is used as an example to illustrate the application of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) coupled with Energy-dispersive X-ray spectroscopy (EDX) and powder X-ray diffraction (PXRD) on solid waste. Furthermore, samples of analytical results are presented and interpreted and the modifications to the industrial process that resulted are explained. Finally, a brief description of the advantages and limitations of the aforementioned analytical techniques is given with an emphasis on industrial solid waste material.

Jan 1, 2011

By Hans Lundberg

An electric survey from a 'plane flown over the ground is much faster and cheaper than an electric survey carried out on the ground. The results are obtained as continuous recordings that are resolvable into both a depth expression and a conductivity effect, so that the indications are easier to evaluate, as well as to correlate from one flown line to the other. The prospecting technique adopted in our electric airborne surveys may be brie fly described as follows: A loop of many turns of insulated copper cable is fastened around the fuselage of the 'plane and connected to a generator supplying a few ampere alternating current, usually of a frequency less than 1,000 cycles per second. Just as the current in the primary coil of a common transformer will induce current in the secondary coil when shorted, the alternating magnetic field from this primary current now induces alternating current in electric conductors that happen to be located in the vicinity of the path over which the 'plane is flown. This induced secondary current in each conductive section of the ground causes, in turn, an alternating magnetic field, secondary field, which disturbs or dampens the normal alternating magnetic field from the primary loop flown by the 'plane. These secondary fields are then picked up and recorded by the help of detecting solenoids, amplifiers, and recorders carried in the 'plane. By closer study of such a secondary field it is possible to localize the secondary current causing it and, thereby, the conducting body that contains the secondary current. In the 'plane are continuously recorded, besides the amplitude or intensity of the field, also the phase, which is a measure of how much the recorded secondary field is out of step with the primary field.

Jan 1, 1950

By W. R. Tyson

Imperfections such as lack-of-fusion and undercut are inevitable in field welding of pipelines. Above a certain size, such defects must be removed or repaired. In the present state of the art, determination of allowable defect size is done by Engineering Critical Assessment (ECA). This requires measurement of toughness, and comparison of toughness with crack driving force. ECA methods used in current international pipeline standards will be reviewed and compared.

Jan 1, 2010

By J. D. Stewart

One of the first important questions that should be settled on the opening of a mine or the development of a new deep is the system of haulage to be used, since the layout of the haulage-ways at the pit bottom, or, in case of a slope mine, the arrangement of the surface works, depends largely upon the type selected. Should it later become desirable to install a system of haulage of a type other than that for which the mine roadways were originally laid out, considerable difficulty would likely be encountered in its installation and with the result that it would in all probability be most unsatisfactory and expensive in its operations. It therefore becomes very necessary that full consideration be given the haulage problem at an early date in order that the type best suited to the mine conditions and the required outputs can be intelligently planned for. It is sometimes found, however, that no matter how well the mining engineer explores the seam to be developed, or how accurately he anticipates its eccentricities, there will still remain some unrevealed or unsuspected conditions, or shall we say obstacles, placed by Nature to prevent the too easy winning of her treasures and incidentally to frustrate or modify the application of the plan so painstakingly laid down on paper, and to adversely affect the cost estimate.

Jan 1, 1928

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By J. Wickens

"Campbell Mine is dedicated to quality management in the form of a Continuous Improvement (CI) Operating Philosophy. This paper discusses that philosophy, why and how it is being implemented in the milling facility, and some of the challenges experienced to date. Examples of mill CI team projects and results are described. This paper describes practical experiences for those who are considering or are in the process of adopting a CI operating Philosophy.INTRODUCTIONCampbell Mine is 100% owned and operated by Placer Dome Canada Ltd. The mine is located in Balmertown, Ontario approximately 300 km northeast of Winnipeg, Manitoba. Campbell Mine has produced over s,000,000 ounces of gold since commencing operation in 1949. The operation is profitable and continues to be a major contributor to the gold production of Placer Dome Inc.At Campbell Mine, the concept of Continuous Improvement (CI) is being implemented to make further improvements to safety, quality, productivity, and subsequently profits. CI is not a ""program"". It is a way of doing business that concentrates on improving the system rather than finding fault and being resigned to the status quo.CI focuses on involving all employees in the decision making process and tapping their expertise to improve every facet of the business. In the past, many solutions were simple ""band-aid"" fixes treating the symptom, only to see the problem resurface again. With CI, solutions endeavour to address the root cause of problems and eliminate them permanently. Another primary goal is to eliminate unilateral decisions that benefit a small group but have a negative effect on the whole system."

Jan 1, 1995

By C. R. Fast, G. C. Howard

The loss of fluid to the formation adjacent a fracture governs the areal extent of the fracture and the success of hydraulic fracturing as a production stimulation technique. The three flow mechanisms which control this loss are the result of the viscosity of the fracturing fluid and the permeability of the formation to the fracturing fluid, its wall building properties, and the combined effects of viscosity and compressibility of the reservoir fluid. The effects of these flow mechanisms can be evaluated in terms of a fracturing fluid coefficient, the fundamental concepts of which are developed in the paper. The fracturing fluid coefficient, which may be used in calculating the areal extent of fracturing, affords a direct measure of the effectiveness of fracturing fluids. The area of hydraulically created fractures is in-creased as the coefficient is de-creased. The fifteen-fold variation noted in this coefficient for the commercially available fracturing fluids tested resulted in a six-fold difference m the calculated areal extent of the fracture system.

Jan 1, 1961

By Y. Lizotte

"This paper examines the application of blasthole sloping to narrow vein mining in Canada, for ore deposits where widths are less than two metres. While the technique has now been utilized for more than ten years, it remains in the experimental stage and on-site testing is necessary for its adoption at new mining operations or in differ¬ent geological settings. It is intrinsically a safer method than other narrow vein methods in current use.The investigation describes the main operating parameters for mines recently surveyed. The criteria for method applicability are defined and the problems encountered are studied. It is concluded that blasthole sloping for narrow vein mining is a viable modern method which promises to gain popularity and that emerging fragmentation technology and blasting research can be used to further increase applicability of the stoping method."

Jan 1, 1991

By Gabriel G. Walton

Conventional numerical modelling tools for analyses of underground excavations are well suited for modelling elastic behaviour and yield response of geomaterials with very simple constitutive behaviour. Non-dilatant elastic and perfectly plastic behaviour is most commonly used for preliminary analyses in the absence of the data required to consider more complex behaviours such as strainweakening and dilation. For truly brittle models, this deficiency is more acute. Current state of practice allows only for reliable estimation of the volume of failure, but not for any prediction of displacement. In fact, there is no consensus in rock engineering regarding the most accurate approach or most suitable tool to model the magnitude of the plastic deformation that strain-weakening or brittle rocks experience at tunnel boundaries, particularly when support is incorporated into these models. This problem is largely a function of a poor understanding of how inelastic dilation occurs in different types of rockmasses, the rate controls on strength loss and volume change during yield, and the complexities of rock-support interaction in yielding conditions.

Jun 1, 2012

By L. A. Wolff

"Second only to profitability (but not always), productivity is the most sought after measurement for any operation. Whether it is in mining, manufacturing, construction, etc. managers always strive to know how productive various plants are. Even the Federal Government publishes, on a monthly basis, the nation's factory productivity.Just what is productivity and how is it measured? This is an important topic that needs definition. There could be as many definitions as there are people who use it. In the mining industry, the problems of defining productivity would be analogous to the definition of equipment availability. Each mine uses its own definition to suit its needs. Webster's Dictionary primary definition for productivity is ""the quality or state of being productive,"" with productive defined as ""yielding or furnishing results"". This is a definition open to a broad spectrum of interpretation. A discussion of how productivity is currently used in the mining industry and an introduction to a potentially different approach to its measurement and meaning is outlined in this paper.Defining ProductivityTypically, mining companies track several productivity measurements. These are partial measurements and can include the following: tons per specific equipment class per hour, tons per man-hour, and tons per shift. None of these, however, track the over -all performance of an operation, that is, a unit of output per unit of input.For a mining operation, output can be defined as the ore for mill processing. Input includes the required components of production to get to the first step of processing.The Wesbter's Dictionary definition exposes a major fault with the popular conception of productivity. The critical issue of accountability is not addressed. Anyone can produce, but how effectively and efficiently are resources used? Quantifying an inclusive measurement is difficult. Statistics referring to an increase in productivity are often published. For example, the statement, ""gold productivity has increased by 10%"" has many potentially dangerous interpretations. One must ask, what does this statistic really mean? Did gold companies produce 10%” more gold? Were less manpower or equipment required to produce an equivalent amount of gold? Did ore grades increase resulting in more ounces of gold produced, etc. Obviously, production and productivity can have similar implied applications and meanings, but also two different, distinct meanings.To mitigate a problem like this, a standard needs to be developed within the mining industry. Because of varying ore grade, changing waste to ore ratios, different mining methods, etc. all of which have a direct impact on mining, development of a standard is difficult. Kendrick(1) discusses the use of Total Factor Productivity as a productivity measurement. Summarized, the total factor productivity measure is an indication of the change in efficiency in the use of basic labour and capital factors associated with an operation.This measurement has little meaning when calculated at a given point in time. It should be an on-going calculation, tracking an operation over a period of time, to evaluate trends. These trends can be used to determine if an operation's productivity is what it should be, and alert management to potential problems before they become major and adversely affect an operation."

Jan 1, 1990

By C. Lapointe

"IntroductionTen years ago, when nuclear fission became practical, the element uranium, until then a not very desirable by-.product of the radium industry, became overnight the strategic material par excellence. One of the several important problems that had to be solved at that time was the rapid and precise determination of uranium in ores and concentrates.GeneralThe chemical analysis of uranium ores is a long and difficult business and is complicated by the presence in most ores of a large number of interfering elements. True, much progress has been made, during the past few years, toward simplification of the analytical methods, but the chemical determination still remains the job of a skilled operator. For this reason, the chemical method has been replaced, whenever possible, by a physical determination based on the measurement of the radiations emitted by the elements of the uranium family. There are several types of instruments suitable for these measurements, but of all the radiation detectors known to the physicist, such as ionization chambers, crystal detectors, scintillation, proportional counters, and the like, the Geiger-Mueller counters have proved to be the most satisfactory for routine determinations, because of their simplicity.The Geiger-Mueller counter is a very versatile instrument; it can be constructed to detect any type of radiation, corpuscular -0r electromagnetic. Here, however, we are interested in these counters because of their ability to detect the beta and the gamma radiations, both emitted by some members of the uranium family. The beta radiation is corpuscular, and is composed of fast electrons, while the gamma radiation is electromagnetic."

Jan 1, 1950

By Kevin Azocar, Jim Hazzard

"Slope stability analysis is performed most commonly using limit equilibrium calculations or numerical models assuming a two-dimensional slice through an infinitely long slope surface. In areas such as open pit mining, where most slope surfaces are not planar, the importance of curvature becomes important due to the economic gains associated with creating a steeper slope. With advances in computing capabilities within the last decade, three-dimensional slope analysis can be performed within reasonable time frames. Some work has been done on the potential importance of curvature on slope stability, mainly assuming homogenous materials with a circular shear-failure mechanism. However, many open pit mines are excavated in jointed rock mass where a completely different set of failure mechanisms can be seen. Depending on the geometry and radius of the pit, the curved geometry may influence the factor of safety and failure behaviour compared to a two-dimensional slice.A series of numerical analyses were performed to investigate the effect of curvature on jointed rock slope stability compared to an equivalent two-dimensional slope analysis. By using discrete element method models, the influence of joint planes and interaction between distinct blocks can be seen. With a three-dimensional model, the effect of curvature can be combined with multiple joint sets at any orientation, which cannot be seen in a single slice. Numerous three-dimensional models are created, along with an equivalent unit-thick slice. The effect of curvature on a variety of different types of failure mechanisms is observed, and graphical relationships are created to quantify the difference between the three-dimensional factor of safety and the two-dimensional factor of safety based on the degree of curvature."

Jan 1, 2015

By T. G. Joseph, M. Bolster, M. Curley

"High tirerim loading on haul trucks operating on rough ground frequently manifests as mechanical separations and rim base cracking caused by cyclic fatigue. This paper provides an understanding of the impact of high loads on rim component life and tire footprint, bulge, and deformation behaviour; and develops a maintenance planning tool to predict strain implications of high g loading for a given rim location. Loading tests and analyses were conducted for a tirerim arrangement under increasing load and internal tire pressure. Graphical models were developed, allowing higher g load extrapolation predictions for specific rim components.KEYWORDS g load, Mining, Model, Prediction, Rim, Strain, Tire bulge, Tire footprint, Ultra-class vehicleRÉSUMÉ L’application d’un chargement élevé sur le système pneu/jante de camions de transport rou¬lant sur des terrains accidentés se manifeste fréquemment par des séparations mécaniques et une fissure à la base de la jante engendrée par une fatigue cyclique. Cet article nous permet de mieux comprendre l’incidence de l’application de charges élevées sur la durée de vie des composantes de la jante ainsi que sur l’empreinte, la hernie et le comportement de déformation des pneus. Il développe également un outil de planification de l’entretien visant à prévoir l’incidence des contraintes en cas d’application d’un chargement g élevé sur un endroit donné de la jante. Des essais et des analyses de la charge ont été effectués pour un agencement pneu/jante soumis à une charge et une pression interne du pneu croissantes. Des modèles graphiques ont été développés, ce qui a permis d’établir des prédictions sur la base d’une extrapolation du chargement g plus élevé appliqué à des composantes spécifiques de la jante.MOTS CLÉS charge g, contrainte, empreinte du pneu, exploitation minière, hernie du pneu, jante, modèle, prédiction, véhicule ultralourdINTRODUCTION The purpose of this paper is to report on a proposed and trialed tire performance test based on data obtained from controlled testing that is used to predict the impact of high g loading on hauler rims and tires with greater accuracy. For example, for many years oil sand mining operations have expressed qualitative beliefs that an impact load of the magnitude experienced by a rim and tire arrangement is not detrimental to a rim as a stiff component; however, mining equipment components are subjected to cyclic loading where failure can result from repeated load/unload activity, truncating the peak region of a stress–strain response and resulting in fatigue failure at a stress value that is less than the peak value. The outcome reported by oil sand haul truck maintenance groups indicates they have realized that most high g impacts—such as those experienced by hauler tires and rims operating on poor ground conditions—can result in failure due to cyclic loading, where higher loads require fewer cycles for failure. This high-level loading and the resulting strain transmitted to the rim is evident in the results of the laboratory testing presented in this paper."

Jan 1, 2019

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

By D Martín, G. Díaz, F. Cubeddu, A. B. Mejias

The Modified ZINCEXTM Process (MZP), developed by Técnicas Reunidas, is an industrially proven flexible process. It can handle a wide range of primary and secondary raw materials, producing SHG zinc. The core of the Modified ZINCEXTM Process is the zinc solvent extraction unit. This unit is an effective barrier for any leachable impurities present in the raw material. As a result of this an ultra-pure zinc solution is always obtained. The high versatility of the process makes the application of the technology in different scenarios possible. MZP can be effectively applied when developing a whole new plant (Skorpion) or adapting its scheme to an existing refinery (Akita), in both cases giving the same results. Flexibility in terms of capacity of the plant is a great advantage of the MZP, there is the possibility to adapt the global process to a wide range of production capacities. Zinc production capacities of over 150 000 t/a may be achieved with a single solvent extraction plant train. The robustness of the Modified ZINCEXTM Process has been recently proven on two new plants currently in operation: Portovesme (Italy) and Horsehead (USA) after start up during 2013. The status of both plants is described in this paper.

Jan 1, 2014

By J. F. Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with bucket-line excavator mounted upon it, which has developed to a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant to work economically the shallower gold gravel deposits that the bucket-line dredges do not work. The dragline dredge consists of the drag-line excavator, on caterpillar mounting on the edge of the dredging pond, which feeds the gravel to the washing plant, mounted on a floating barge in the pond. There have been more than twenty-five such plants built and operated in central and northern California and an unknown number in other States. There have been variations in details of design but the essentials are similar in all. I wish to describe the operation of a typical drag-line dredging plant, that of the Wyandotte Gold Dredging Company on the Farnan Ranch in the Oroville district. This organization of six active partners built their first plant on Wyandotte creek in the autumn of 1933. The operation was successful due to wise management, which was based upon good plant design and proper principles of operation. The partners elected one of their number, H. F. England, as manager with full control and responsibility. This plant and operation furnished the pattern for many subsequent ones.

Jan 1, 1937