Search Documents

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By D. C. Fuller

"CoaLiquid, Inc. (CLI) has been in the coal-oil-mixture (COM) business for over five years. The initial pilot processing facility was replaced by a 2000 barrel per day commercial production facility in August 1979. For over two years CLI has been expanding its efforts and conducting large-scale production and combustion demonstrations successfully in many locations across the United States. To facilitate the marketing effort, CLI has recently constructed a special trailer containing all equipment needed for a temporary COM retrofit.CoaLiquid has conducted commercial-scale combustion demonstrations in the following types of combustion units: kilns, calciners, industrial boilers, blast furnaces and driers.IntroductionCoaLiquid, Inc. officially dedicated its plant on August 31, 1979, at a ceremony presided over by the then Governor of Kentucky, The Honorable Julian Carroll. The dedication marked the culmination of over three years of research and development work and marked the beginning of a new era of coal-oil-mixtures as a commercial commodity in the marketplace. As the first such plant in the United States, it set the tone for construction to follow.CLI was originally owned and managed by a group of entrepreneurs from Kentucky who had developed the process and constructed the plant on purely private investment and conventional financing. Beginning in late 1976, with a pilot-scale operation, also located in Shelbyville, Kentucky (near Louisville), CLI began producing a stable mixture of 50070 coal, 30% to 40% oil and 10% to 20% water by weight. The technology employed was developed by Eric C. Cottell of Long Island, New York and is covered by U.S. Letters Patent No. 3,941,552. Since the pilot plant operation, CoaLiquid has made many refinements to its process and in fact has added new technology to its portfolio of patents and patents pending. Further refinements to the product now produce a stable mixture of 50% coal, 40% No.6 fuel oil and 10% water by weight."

Jan 1, 1985

By S. Mostaghel, Fariba Azgomi, Steven Goodman, M. Oliazadeh

"It is known that copper loss to the slag phase can be in the forms of chemical dissolution and mechanical entrainment. The contribution of each mechanism to the total Cu-loss depends on different parameters and may vary significantly. To reduce emissions to the atmosphere and to shorten the converting cycle, most industrial processes are aiming at production of high matte grades. Increased oxygen-to-sulfur potential, required by these processes, results in a highly oxidized slag, which in turn leads to an increased concentration of the chemically dissolved copper in the slag phase. Hence, slag cleaning processes are becoming increasingly important for economic viability of the smelting operations. Hydrometallurgical, pyrometallurgical, and mineral processing routes have been used for copper recovery from slag. The current article reviews a trade-off study evaluating two of the commonly used methods (namely flotation and electric slag cleaning furnace) by comparing the technical pros and cons, operability/maintenance requirements, and capital/operating costs of the operations.INTRODUCTIONLarge volumes of smelter and converter slags are produced by copper smelters around the world. It is estimated that for production of each ton of metal 2.2 tons of slag is produced (Gorai, Jana, & Premchand, 2003). Considering the current pressure on the mining and metals industry for “zero-waste, sustainable and environmentally friendly” extraction of metals, it is absolutely essential for metal producers to improve their efficiencies in order to remain competitive. To meet these objectives, almost all metal producers, from steelmaking plants, ferroalloys, base and precious metals producers, are trying to reduce their metal losses to the slag phase. In particular, copper producers are aiming to produce higher matte grades in their smelting furnaces to reduce the converting time and improve their overall throughput. Copper smelters need to minimize their copper/precious metal losses to the slag phase before final landfilling/use of slag. The current article, therefore, briefly reviews the copper loss to the slag phase, methods of metal recovery from the slag and then presents a trade-off study conducted for a green field flash smelter of the sulfide concentrates. A comparison was made between two of the major process routes for metal recovery from slag, namely slag cleaning furnace and flotation."

Jan 1, 2016

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By Mengsu Hu, Yuan Wang, Jonny Rutqvist

Material interfaces and typical boundary conditions are boundaries influencing the existence, uniqueness and stability of numerical solutions of water flow in heterogeneous media. The Numerical Manifold Method (NMM) with a two-cover-meshing system is an ideal method to handle boundaries, considering its flexibility with no need to adjust mathematical nodes onto boundaries, the meshing efficiency, and its integration precision. In this study, we derive and compare two new approaches for boundary constraints, i.e., a discontinuous approach with Lagrange multiplier and a continuous approach with jump function in the frame of NMM. In the discontinuous Lagrange multiplier method (LMM), Dirichlet boundaries or the material interfaces are regarded as discontinuities which are linked by Lagrange multipliers. In the continuous Jump function method (JFM), the material interfaces are regarded as inner interfaces, where the refraction law is realized by constructing jump terms with discontinuity of hydraulic gradient in its normal direction. Both the continuous and discontinuous approaches make full use of the aforementioned advantages of NMM and are established based on a clear physical meaning of water flow by our energy-work seepage model. The newly derived boundary-constraint approaches were coded into an NMM water flow model and tested for precision and efficiency on different simulation examples. We first tested both LMM and JFM for an idealized heterogeneous model, comparing the numerical results with analytical solutions. Then we tested both approaches with a heterogeneous model and compared the results of hydraulic head and specific discharge. We proved that both approaches are very suitable for material boundaries considering the accurate realization of the boundary constraints and the flexibility with no need for mesh-conforming.

Jan 1, 2015

By J. A. Drozdiak, W. Tse, P. P. Rosario

"In a recent publication (SAG 2015), we presented a non-conventional high pressure grinding roll (HPGR)-ball mill circuit as a lower capital cost alternative to the “standard” HPGR circuit. The circuit was designed for the treatment of a hard ore and relatively high tonnage (50,000 t/d). That paper provided details such as flowsheets, layouts, and equipment lists for the two options and compared their calculated capital costs demonstrating significant savings for the proposed circuit. This paper extends the analysis to a third option, a traditional semi-autogenous ball crushing circuit, giving the same level of details and now including the operating cost estimates for all three options for a more comprehensive analysis. Moreover, this work also provides information about the strengths and weaknesses of the non-conventional HPGR circuit when compared to the “standard” HPGR option.This study demonstrates that the proposed non-conventional HPGR-based circuit not only provides a lower overall capital costs for the project if compared to a “standard” HPGR circuit but also brings the capital cost to the level of the traditional semi-autogenous grinding (SAG)-ball mill circuits. In addition, the innovative HPGR circuit provides similar operational cost savings of the “standard” HPGR and thus a significant advantage when compared to the SAG option. With the current capital cost sensitivity for most greenfield projects, the proposed alternative circuit should help make HPGR-based circuits more competitive and thus promote the utilization of a technology that enables higher energy efficiency and reduced greenhouse gas emissions. INTRODUCTIONThe application of high pressure grinding roll (HPGR) technology in comminution circuits is well established for the processing of cement, diamonds and iron ore (Broeckmann & Gardula, 2005), and over the past 10–15 years, this technology has slowly been applied to hard ores in high-tonnage precious and base metal operations. Unfortunately, under the current economic climate, the ability to finance large capital projects has become very difficult and companies tend to have an easier time securing funding if the capital expenditures (CAPEX) are low with a proven process method. The traditional semi-autogenous grinding (SAG) mill / ball mill circuits easily fit into this mould, having been installed in countless plants around the world over the past 30 years with relatively low capital requirements. In contrast, it has been well-documented that HPGR-based circuits are capital intensive with complex material handling systems (Seidel, Logan, LeVier, & Veillette, 2006). Although these circuits benefit from reduced operating costs with the increase in energy efficiency and the elimination of steel grinding media (Rosario, Boyd, & Grundy, 2009), if the company is unable to secure financing to build the plant, these advantages remain out of reach. With the current trend to retrofit existing SAG circuits with a secondary crushing circuit to achieve design throughput, the opportunity to circumvent this gross inefficiency by making HPGR-based circuits more capital friendly would greatly benefit the industry."

Jan 1, 2016

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By M. M. C Jiménez, D. C. Buzzi, D. C. R. Espinosa, J. A. S Ténorio, G. F. R Oliveira

In this work the extractive and selective capacities of solvent extraction synergistic systems to recover nickel and cobalt were evaluated. The liquor used was from the high pressure acid leaching process (HPAL). Initially the industrial liquor, processed from lateritic ores, was analyzed to identify the concentrations of the metals. Experiments of synergistic solvent extraction were performed later. The extraction liquid-liquid was carried out with a mixture of Cyanex 272 (CY) and Ionquest 290 (IQ) extractants. The process was executed with the temperature of 65 ºC, pH of 5.2 and the ratio aqueousorganic 2:1. Systems of 80% kerosene and CY 20%, CY 16% - IQ 4%, CY 12% - IQ 8%, CY 8% - IQ 16%, CY 4% - IQ 16%, IQ 20% were studied during 20 minutes. The results of this paper showed that the mixture of these two extractants doesn’t improve significantly the recovery of nickel and cobalt from liquor.

Jan 1, 2014

By J. O. Wheeler

"DEFINITION OF THE REGION, ITS BOUNDARIES, AND PHYSICAL AND GE'OLOGICAL CHARACTERISTICSTHIS PAPER concerns the Western Cordilleran region, embracing most of British Columbia, the southern half of Yukon Territory and the southwestern most part of the District of MacKenzie. It excludes Vancouver Island and the Queen Charlotte Islands, which are discussed in a background paper on the Pacific Continental Shelf. The region is bounded on the south by the northwestern United States, on the west by the continental shelf and Alaska, on the north by the front of the Ogilvie Mountains, on the northeast by the axis of the MacKenzie Mountains and on the east by the Rocky Mountain Trench.The region is dominated by two mountain chains that con tain icefields and glaciers: the St. Elias, Coast and Cascade Mountains in the west; the Selwyn, Pelly, Cassiar, Omineca and Columbia Mountains in the east. The Intermontane region between these mountain chains consists of lower mountains and plateaus. In the mountains, the region above the timberline and many of the steep valley-walls provide good exposures of rock, but these areas are subject to rockslides and landslides and in winter to snow avalanches. Much of the Western Cordillera was covered by ice-sheets at various times during the Pleistocene epoch. Consequently, the larger valleys in the mountains and much of the Intermontane region contain much glacial drift and alluvium and only limited exposures of rock. This same terrain in the Southern Cordillera, however, is the most favourable for agriculture. Parts of the region, particularly in the two mountain chains, are heavily forested. Elsewhere, the forest cover is less, with grassland prevailing in the south and tundra in the north."

Jan 1, 1969

By J. O. Wheeler

"DEFINITION OF THE REGION, ITS BOUNDARIES, AND PHYSICAL AND GE'OLOGICAL CHARACTERISTICSTHIS PAPER concerns the Western Cordilleran region, embracing most of British Columbia, the southern half of Yukon Territory and the southwesternmost part of the District of MacKenzie. It excludes Vancouver Island and the Queen Charlotte Islands, which are discussed in a background paper on the Pacific Continental Shelf. The region is bounded on the south by the northwestern United States, on the west by the continental shelf and Alaska, on the north by the front of the Ogilvie Mountains, on the northeast by the axis of the MacKenzie Mountains and on the east by the Rocky Mountain Trench.The region is dominated by two mountain chains that con tain icefields and glaciers: the St. Elias, Coast and Cascade Mountains in the west; the Selwyn, Pelly, Cassiar, Omineca and Columbia Mountains in the east. The Intermontane region between these mountain chains consists of lower mountains and plateaus. In the mountains, the region above the timberline and many of the steep valley-walls provide good exposures of rock, but these areas are subject to rockslides and landslides and in winter to snow avalanches. Much of the Western Cordillera was covered by ice-sheets at various times during the Pleistocene epoch. Consequently, the larger valleys in the mountains and much of the Intermontane region contain much glacial drift and alluvium and only limited exposures of rock. This same terrain in the Southern Cordillera, however, is the most favourable for agriculture. Parts of the region, particularly in the two mountain chains, are heavily forested. Elsewhere, the forest cover is less, with grassland prevailing in the south and tundra in the north."

Jan 1, 1970

By D. L. Morgan, J. A. Butterfield

"Geological data, production trends and current projects underway suggest that enough molybdenum will be available from more diversified sources to meet the world's growing demands. The growth in molybdenum consumption has been primarily related to its beneficial effects as an alloying agent in steel. This rapid growth has been deliberately fostered by stable prices, adequate supply and application research. The molybdenum industry is now in a process of change which has been seen in several other metals, such as aluminum and nickel. As supply sources have become more diversified, the market has become more competitive. The recent drop in consumption has led to excess production capacity, accumulation of substantial producer inventories and increased market uncertainties. While consumption is expected to increase in the next two to three years, it will take some time to absorb the excess capacity and inventory. The increased proportion of by-product capacity indicates that prices may become more variable. Producer discipline will be required to prevent serious price erosion in times of surplus. Future prices may not continue to increase with inflation. For the longer term, several factors favour the increased consumption of molybdenum. Engineering requirements are becoming more severe and molybdenum alloys can help to meet these changing needs. In addition, consumers can rely on a large and increasing supply of molybdenum. A 7 per cent growth rate in consumption can probably be sustained through the next decade, but new applications and reasonably stable prices will be needed to make this possible."

Jan 1, 1972

By Hector Monette

"AFTER SPENDING a lifetime in the mining industry it is normal that one should be concerned with the future of his profession, especially if he is directly responsible for the education and formation of future mining engineers. It is not necessary to insist on the importance of mining for Canada and for the entire world to prove the necessity of the Mining Engineer. A statement was made by Zay Jeffries, former vicepresident of General Electric Co., and here I quote: ""Even though minerals without man are of no moment, man would not be man as we know him without minerals ... ""minerals are as essential to the life of social man as food is to man himself"". This certainly expresses magnificently the purpose of the mining profession. These are the reasons why I have accepted to present my views on the future of the Mining Engineer. If I express some concern it is not because I feel that there is any danger for the profession to disappear; men will always respond to a challenge and this can be found in the extraction of minerals as well as in any other field of human endeavour. However, the first big question concerns the competitive position of Canada in the world of mining. To be made available to Canadians and to the rest of the world, all this tremendous potential mineral wealth that our country has been so generously endowed with by nature must be gained from the earth's crust at a competitive cost. Otherwise it will never become ore and will have no value. Let us not forget that although minerals are discovered, mines are not found but are made. So let us be more efficient mine makers. To accomplish this end, it is the duty of the different responsible organizations at all levels - be they governmental, para-governmental, public or private institutions - to do their utmost to assure the profitable development of our mineral wealth. The University has an all-important role to play in preparing all the specialists required by this intricate machine that mining is. All the different disciplines of engineering, health, social and -managerial sciences are needed for the good functioning of the mining industry. Although they are all essential, some will play a more important role as a member of the structure. In this discussion it is the role of the most important member, the mining engineer, who is actually responsible for the extraction of the minerals from the earth's crust that must be established. From this we will then be able to analyse his responsibilities and try to suggest the mining engineering program most suitable to prepare this engineer for his future role."

Jan 1, 1972

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

By E. V. Manlapig, M. A. Hampton, M. E. Holuszko

Methanol treatment of ZnS particles has been found to remove slimes and facilitate flotation. The removal of slimes renders the ZnS surface more hydrophobic, resulting in an increase in the hydrophobic attractive force between the particle and bubble. Hallimond tube flotation, induction time measurement and particle-bubble force analysis with the atomic force microscope (AFM) was undertaken to link the beneficial effect of methanol treatment of ZnS particles to their increased floatability.

Jan 1, 2009

By G. W. H. Norman

"During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in mapping major faults by using aeroplane photographs with a scale of about 1,000 feet to 1 inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately.Geology of the Abitibi RegionGeneral GeologyFaults of more than one age and type occur in the Abitibi region. In order to appreciate some of the age relationships of the faults, a brief summary of the historical aspects and major structural features of the geology (fig. 1) is necessary. These historical aspects may be briefly summarized in chronological order as follows:(1) Accumulation of Archæan lavas and associated pyroclastic rocks, either alternating with, or essentially followed by, deposition of sedimentary rocks, and interrupted at least once by local and perhaps regional folding and erosion."

Jan 1, 1954

By M. Pawlik, E. Arinaitwe, V. Ferrera

A series of flocculation tests were performed on dilute quartz suspensions with the use of five polyacrylamide-based flocculants of similar molecular weights but of different degrees of anionicity. The tests were performed as a function of ionic strength and pH. The macromolecular conformation of flocculants in solution was assessed through intrinsic viscosity measurements under the same physicochemical conditions as those of the flocculation tests. It was generally found that the flocculating efficiency of the polyacrylamides correlated with their ability to coil or stretch in solution. Polyacrylamides with the degrees of anionicity on the order of 10-18% showed the highest flocculating efficiency in terms of the settling rates of the flocculated solids and the residual turbidity of the resulting supernatant. At the same time, these most effective flocculants were also found to exhibit the greatest tendency to coil and stretch in solution. This result suggests that the flocculating power of a flocculant is determined not only by its ability to adsorb onto (and bridge) fine particles but also on its ability to conform to the size of the resulting floes.

Jan 1, 2009

By R. I. Kraydenko, A. N. Dyachenko

"The possibility of SiO2 5N production by staged purification of ammonium hexafluosilicate (NH4)2SiF6 is discussed. High-purity silicon dioxide can be obtained with fluoridation of quartz concentrate by solid NH4F at 100 °C, with further sublimation of the product at 320 °C, its dissolution, ammonia hydrolysis, filtration and drying of SiO2•nH2O. This is accompanied by regeneration of the processing reagent - NH4F.INTRODUCTIONProduction of high-purity silica-5N (SiO2 content over 99.999%) is an important and urgent task of the modern chemical industry. This material is used in the manufacture of optical glass, optical fibers for internet cables, silicon for solar power and electronics.Quartz concentrate is raw material for the production of silicon dioxide. The existing technologies of synthetic silicon dioxide were introduced in the mid-twentieth century. These methods are energy-consuming, multi-step and do not meet stringent environmental requirements. In fact, as some conventional technologies became obsolete; it became necessary to develop new methods for the production of synthetic silica. We believe that the fluoride technology of processing of quartz materials by ammonium fluoride is the most promising direction.In industry, silicon dioxide marked ""Silica White"" is obtained by liquid-phase method. The method consists of the precipitation of amorphous silica from sodium silicate solutions with acids. The resulting product is filtered, washed and dried. Depending on the deposition conditions and nature of the coagulant the ""Silica White"" is acidic, neutral or alkaline. The dry product is subjected to grinding. The degree of dispersion and porosity of the particles of Silica White depends on the nature of decomposition agent (a substance that decomposes the silicate) and coagulant, conditions of sedimentation, filtration and drying. During the drying process the silica particles are sintered into aggregates of a few millimeters."

Jan 1, 2012

By Ross Gallinger

In 1997 a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded (i) that Canadian industry and NRCan should fund a small secretariat in Ottawa to support technology transfer in Canada and (ii) that it was important for industry to continue the momentum of MEND on an international scale. The need for INAP (International Network for Acid Prevention) was strongly endorsed by company, university, consultant and government experts from Australia, Canada and the U.S. who were convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP's members to promote the dissemination of successful practices, the identification of knowledge gaps and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry based initiative to globally coordinate research and development in the management of sulfide mine waste. Significant improvements in the management of sulfidic mine materials through knowledge sharing, research and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP.

May 1, 2002