Search Documents

By J. -C. Parisien-La Salle, D. Blais, G. P. Demopoulos

"In this work the dissolution, precipitation and adsorption behaviour of gold in acidic iron sulphate media containing small amounts of chloride ions is investigated via batch laboratory tests and OLI thermodynamic calculations over the temperature range 25-250°C. Chloride ions may be present in industrial pressure oxidation/pressure leaching (POX/PL) operations due to elevated water salinity levels or due to intentional addition as is the case of the CESL Copper Pressure Leaching Process. Thermodynamic calculations show that AuCl4 - may form depending on the free Cl-/Au ratio and temperature, its stability increasing with increasing Cl- concentration and decreasing with increasing temperature. On the other hand during POX/PL, we know that massive precipitation of iron in various hydrolysis products and compounds occurs. Hence of interest is the question how AuCl4 - that may form during leaching interacts with the iron precipitation products. Gold(III) chloride was found to co-precipitate with iron(III) (oxy) hydroxides and arsenates forming in the autoclave but not with natrojarosite. Upon further investigation it was discovered that activated carbon added in the autoclave (as done in CIL) acts as preferential sink for the mobilized gold, hence opening the potential for the development of a direct cyanide-free gold recovery process in acidic sulphate leach reactors.INTRODUCTIONThe recovery of gold from ores and concentrates has evolved over the years with processing routes becoming increasingly complex. Given the high value of gold, any reduction in losses during recovery operations constitutes an important economic benefit. One such loss that needs to be addressed is the potential solubilisation of gold during pressure oxidation (POX) of refractory sulphidic gold feedstocks. For example, Agnico Eagle Mines reported a loss in gold recovery due to the formation of a gold chloride complex (Garofalo, 2009). Gold is known to form complexes in solution, such as gold(III) chloride, if an excess of chloride ions are present. The fate of such soluble gold chloride during pressure oxidation and the subsequent neutralization of the acidic discharge slurry will determine if gold is lost or recovered in the downstream cyanidation operation. Thus it is of interest to know under what conditions gold chloride may stay soluble or co-precipitate along primary (formed in the autoclave) or secondary (formed during neutralization) precipitates. Furthermore, the mode of co-precipitated gold, such as adsorption on iron compounds, like goethite and hematite (Machesky et al., 1990; Nachayev, 1984); substitution in one of the precipitated phases; or finally chemical reduction to metallic state would have consequences in terms of gold recovery."

Jan 1, 2012

By Deborah A. McCombe

"There are a number of important dates that must be disclosed when a Qualified Person (QP) is preparing a technical report for securities purposes. The dates are discussed in NI43-101 and the Form of the Technical Report, NI43-101F1. •,Effective date of the technical report •,Possible revision date of the report •,Effective date of mineral resources and mineral reserves •,Date of the personal inspection (site visit) •,Signature date of the date report (execution date) •,Date of the certificate of the QP •,Date of the consent of the QP The effective date of the report is basically the cut-off date for the information that is included in the technical report. The effective date should be close to the signature date. If there is too long a period between these dates, the QP runs the risk of new material information becoming available and then the technical report would no longer be current. The effective date is disclosed on the title page of the report and on the signature page. If a technical report needs to be revised to correct problems or disclosure deficiencies identified by the regulators, the QP will normally need to include a revision date on the title page of the report to distinguish the revised version from the original version. In these circumstances, the regulators will request that the original date of the report remain on the title page and the revised date will be below it. When a technical report must be revised, the QP must resign and date the signature page of the report and provide a new certificate and consent."

Jan 1, 2003

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By P .. H. Grimley, N. Champigny

"Fourteen companies (Appendix) representing senior mining organizations in Canada were canvassed in order to assess: (1) the current usage and trends, and (2) the usefulness of computer applications in ore reserve estimation and grade control. The results of the questionnaire suggest that:• computers are unsurprisingly, predominant in the mining industry for calculating reserves and performing grade control;• time and cost savings are realized;• computer-based approaches are applicable to underground situations;• geological information is incorporated to the computerization process; and• computer usage does not hinder the collaboration of geologist and mining engineer.A clear need is identified for case histories comparing computer-calculated ore reserves and actual production data.IntroductionAmong the management and technical staff of some mining companies there is a perception that the application of computer based technology for the estimation of ore reserves and grade control, has as many drawbacks as benefits. Some of the objections raised against the utilization of computers for ore reserve estimation are that:• computer-based reserve models work for large open pit mines but not for underground situations;• computer-generated reserves ignore the geologist's knowledge base; they are strictly a number crunching exercise; and• the use of computers for ore reserves hinders collaboration between the geologist and mining engineer.In order to determine (I) the extent of current computer usage and future trends and (2) whether the objections noted above are borne out by experience, a number of senior Canadian mining companies were canvassed.The respondents were asked to provide:• an assessment of the importance of the computer in the ore reserve estimation and grade control process;• the level of involvement of individuals and staff groups with computer-based ore reserve estimation;• the advantages perceived and realized from the utilization of computer-based ore reserve approaches;• the current and future human resources requirements for the evaluation, implementation, maintenance and development of computer-based ore reserve systems;• the hardware and software resources presently used and planned; and• the developments needed to increase the use and acceptance of computer-based ore reserves."

Jan 1, 1990

By P. G. Thornhill

EARLY in 1951, Falconbridge undertook a research program aimed at the development of a sulphate roasting process for the recovery of the non-ferrous rnetals from the nickeliferous pyrrhotite fraction of Falconbridge ore, in order to reduce the tonnage of iron entering the srnelter. Such a method, it was hoped, would permit a high recovery of the nickel from pyrrhotite otherwise entering the smelter feed, thus not only raising the grade of the latter and reducing its iron content, but also providing an iron oxide residue useful as a source of by-product iron ore. At an early stage in the exploratory laboratory test work it was found that the degree to which the nickel could be solubilized by the sulphating roasting treatment was limited by particle size and the ex-tent to which the pyrrhotite concentrates were freed of the nickel occurring as physically separable pentlandite, a mineral relatively difficult to roast. ( 1) Thus the program

Jan 1, 1961

By A. W. Jolliffee

ANY attempt to forecast the mineral resources of a largely unknown region is hazardous and, in the case of the Northwest Territories, such a task is even more hazardous than usual. This is not merely because of the immense territory involved (over a million and a quarter square miles), only a small fraction of which has ever been explored or prospected, but also be-cause both the geology and mineral deposits thus far examined show many unique features, and, finally, because the region is being actively prospected at the present time. However, in view of the present widespread interest in Canada's mineral resources, a brief compilation of what is known regarding mineral occurrences and geology in the explored parts of the far north seems timely. From these assembled data, a few inferences are warranted as to future mineral production from this region. HISTORY The story of mineral discovery in the Canadian northwest is a fascinating one. As well, it abundantly illustrates the importance of mineral occurrences in indicating future mining possibilities. The same sequence of events has repeated itself too often to be merely fortuitous.? In most cases, the dis-covery of a mineral deposit of possible economic value has been foreshadowed by the finding of the valuable mineral or an associated mineral in the same district, generally in small quantity, by an early explorer or traveller. Thus, John Franklin reported oil seepages from the base of Bear Rock, near Nor-man, at almost the very spot where oil was struck nearly one hundred years later. Again, some would-be Klondikers, deterred by the hardships of the route, remained to prospect around Great Slave lake, and were the first to report the Pine Point lead-zinc occurrences there and the gold-bearing veins on Yellowknife bay. Sporadic prospecting followed at the latter locality for over thirty years before the recent rich strikes were made. Similarly, in 1847, Dr. John Rae picked up a boulder of copper ore south of Rankin inlet, on Hudson bay. More than eighty years later, a body of copper-nickel sulphides carrying values in platinum metals was found at this locality. Also, the report of cobalt bloom on the east coast of Great Bear lake brought back by a Geological Survey of Canada party in 1900 was a factor in the events leading to the discovery of silver and radium there in 1930.

Jan 1, 1937

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

By A. M. Bell

General Summary THIS paper attempts to describe in a preliminary and general manner the nature of certain copper discoveries now being developed by Gaspe Copper Mines, Limited, in Holland township, in the interior of the Gaspe peninsula. Some copper mineralization appears to have been known here at the time of the earliest French explorations, was rediscovered in 1921, and has been under intermittent development by Noranda Mines since 1938. In the last two years discoveries have enhanced the picture so that the deposit now promises to develop into one of the important Canadian copper producers. As ideas are constantly changing with continuing development, any picture given now is very partial and tentative and must be subject to future revision. The nature of these copper occurrences differs from others known in eastern America. In many respects they have unique features but they are most closely akin to some copper deposits found away from the intrusive rocks in the porphyry copper districts of the western United States. The most important orebodies are replacement deposits in a limestone horizon in which the ore gangue is converted to skarn. These lie at considerable distances from any known intrusive but seem to have been derived from a buried stock of granite that intrudes the sedimentary rocks of Lower Devonian age. This intrusive has produced alteration effects in the overlying rocks that may afford a key to locating other ore areas in the Peninsula.

Jan 1, 1951

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By F. F. Langford

"The Athabasca Basin occupies about 100,000 km2 of the northwest corner of Saskatchewan with its western margin extending about 50 km into Alberta (Fig. 1). The basin is filled with a Helikian sequence of predominantly fluvial sandstones up to 1600 m thick. The sandstone beds are generally flat-lying, and rest unconformably on a crystalline basement which consists mostly of granitic intrusive complexes and quartzfeldspar- biotite gneisses. The basement rocks represent Aphebian sediments and Archaean basement rocks that were metamorphosed and remobilized to varying degrees during the Hudsonian Orogeny (ca 1800 Maj.Since 1968, three mining camps and several substantial unconformity-type uranium deposits have been discovered in the area (Figs. 1 and 2). These deposits lie along the unconformity surface, partially enclosed in sandstones, and partially in the basement rocks. The major deposits have elongate, pencil shaped orebodies that are parallel to the strike of underlying graphitic biotite gneisses. The total tonnage of uranium is in the order of 150,000 to 200,000 tonnes and mining grades range from 0.5 to 2.5 per cent U3O8.IntroductionUranium exploration started in Saskatchewan in 1945 when Jolliffe and Murphy headed field parties to investigate uranium occurrences on the north shore of Lake Athabasca (Kupsch, 1978). Their investigation lead to the development of the Beaverlodge camp in the following years. Some of the early prospectors were impressed by the fact that the uranium occurrences at Beaver lodge were centred on a thick sequence of unmetamorphosed arkosic redbeds which are now called the Martin Group. This sequence was referred to as the Athabasca Series by Christie (1949), and although some occurrences of uranium were found near Stony Rapids and Black Lake, the vast expanse of Athabasca sandstones south of Lake Athabasca was generally regarded as unpromising."

Jan 1, 1986

By S. Utili

"The optimal profile of a rock slope under given geometry constraint is investigated by means of the upper bound method of limit analysis. The optimal condition corresponds to maximizing stability factor. It is assumed that rock failure condition is suitably described by the Hoek-Brown criterion. Genetic algorithm is applied for locating the optimal profile. The optimal profiles turn out to be concave profiles but there are heaps around the toes of the slopes. Compared with plane profiles, the percentage of increase in stability factor can reach up to nearly 50%. The key geometry parameters of the optimal profiles are provided for practical use. The new upper bound formulation is capable of computing the stability factors of slopes of any shape, thus the stability status of a slope under man-made excavation can be monitored during the whole construction period.INTRODUCTIONIn mining industry, man-made slopes are excavated to create working surfaces. It is important to optimize the slope profile in order to maximize slope stability under certain geometry constraint. For instance, when the height and width of an excavation are assigned, a plane profile AC (see in Fig. 1) is widely applied in engineering practice, but it has been proved not the best one in terms of safety (Utili & Nova, 2007; Cala, 2007). A vertical profile ABC is the one with least stability. Thus, it can be deduced that there is a profile within the domain of the rectangle ABCD providing the highest stability. Cala (2007) compared the difference of convex and concave profiles in stability using strength reduction technique. According to Cala (2007), circular concave slopes can increase the maximum slope inclination under given factor of safety. Besides, based on upper bound theory of limit analysis, Utili & Nova (2007) assumed a logarithmic spiral profile to prove it is more stable than a plane profile in terms of the stability factor. Although the above studies attempted to seek the best circular or logarithmic spiral profiles, none of them considered the arbitrary shape of the optimal profile and its contribution to enhance slope stability."

Jan 1, 2015

By M. A. Bergougnou, I. Inculet, K. I. Burgess

This paper describes the electrostatic methods of separating various minerals, reviews the principles of fluidization and outlines the technique of electrostatic sorting in fluidized beds. The application of the method to the benefication of coal is emphasized.

Jan 1, 1970

By R. D. Brown

"""A matter of serious concern to the mining industry in British Columbia""; this comment reflects the attitude of the Mining Association of British Columbia toward the proposed new B.C. Mineral Royalties Act. The proposed legislation, introduced by the provincial government in February and now being debated by the legislature, combines a basic 5% royalty on the selling price, less approved p1ocessing and transpo1•tation costs, of minerals produced in B.C. with an ""excess"" royalty of 50% of any price increases over a predetetmined base. Government estimates project annual revenues of $20 million from the new royalty structure. The accuracy of these figures has been contested by the mining industry. Based on current world prices for copper the industry estimates that the provincial revenues from this mineral alone may run as high as $140 million in 1974 and $150 million in 1975. The Mining Association has warned that the new royalties “threaten to become confiscatory""."

Jan 1, 1974

By Sean McClenaghan

Significance Setting Size Production Value History of Discovery Zn and Pb at Austin Brook Brunswick Belt Exploration Discovery Hole Geology Structure Metal Zonation Directed Research Incremental Ores Precious metals Closure and Beyond Mining Remnants Tailings

May 1, 2013

By Albert G. Zima

THE conservation of strategic materials during war rime gives rise to many problems not commonly encountered in times of peace. During normal times, when world trade is unrestricted, we are apt to become lavish to a point of extravagance in our use of those materials which, during rime of war, become scarce owing to inadequate transportation and production facilities or because the enemy may be in position to control sources of supply. It becomes necessary, then, to enforce rationing of available sup-plies, and in some cases, where such supplies are wholly inadequate, we find we must resort to the use of substitute materials. We are now confronted with such a problem to an extent never before experienced, with the result that many of the commodities upon which our civilization depended are now either shut off completely or, because of the heavy demand occasioned by war production, are not available in sufficient quantities to meet requirements predicated on peace-time standards and manufacturing methods. It has become necessary, therefore, to make many changes, some of them very drastic indeed, to enable us to carry on our war effort effectively. This? discussion will deal briefly with one phase of this problem, namely, the conservation of alloys required in the making of steels necessary for war production. In line with a request from the War Production Board, the Technical Committee on Alloy Steels of the American Iron and Steel Institute made a study of experimental steels embodying the !east amount of alloying constituents, with the objective in mind of substituting these steels wherever possible for the standard alloy steels used heretofore. This study embraced the following phases: (1) The availability of silicon and manganese; (2) The average quantity of alloying elements recoverable from scrap; (3) The effect of increases in manganese and silicon contents on the general properties of steel; ( 4) The elements and ranges of elements which might be used to duplicate the hardenability of the steels now in use; (5) The effect of combining several elements in small quantities upon the properties of steel at various hardness and strength levels; (6) A determination as to whether or not the steels selected would suffice for general application. Working on this basis, the Committee arranged for the manufacture of several heats of steels containing various combinations of different amounts of such elements as silicon, manganese, chromium, nickel, and molybdenum. The steels thus produced were compared by hardenability tests.

Jan 1, 1943

By J. J. Baz-Dresch

"The Cannon Mine, a joint venture between Asamera Minerals (the operator) and Breakwater Resources, is located in the centre of Washington state at the eastern base of the Cascade Mountains. The mine complex is located three blocks south of the city limits of Wenatchee, part of an urban area with a total population of 47 000. The closest residence is 350 feet from the mine portal.The B-Neath zone is a narrow, high-grade, downward extension of the southern tail of the mine's main ore body, the B-North zone. It also underlies the northernmost portion of the B-West zone (Fig . I) . The ore is usually reasonably competent but completely surrounded by very weak rock consisting of shear zone and unsilicified sandstones and siltstones.The zone has maximum dimensions of 420 ft in thickness, 500 ft in length , and 200 ft in width . The economic reserves extend from the 70-ft elevation (elevation above sea level) to the 630-ft elevation and consist of about 1.3 million tons of geologic reserves (proven and probable) at an average grade of 0.33 ounces per ton.Acquisition and ExplorationInitial DiscoveryThe initial discovery of the B-Neath zone was made by Tenneco Minerals during July through September, 1984. Their 22-hole surface drilling program consisted of 18 200 ft of drilling. Tenneco Minerals had acquired the 91/2 acre lease from United Mining Corporation.Asamera Minerals subsequently purchased Tenneco's lease in July, 1985; Tenneco retained a royalty position which was later purchased by Echo Bay Mining.Follow-up drilling by Asamera Minerals consisted of both surface and underground drilling. Eight surface holes (7200 ft) were drilled commencing in December, 1985. Following evaluation of the geologic data, an access drift was driven on strike along the top of the ore zone on the 500 level. Diamond drilling from this platform consisted of 17 200 ft in 79 holes."

Jan 1, 1990

By W. J. Cherones

This paper describes the history of the development and application of the electric mining shovel in open-pit mining, dea1ing particularly with far-reaching advancements in three primary areas: metallurgy, mechanical design and electrical systems. Hoist drives and crowd drives, including the Magnetorque and Electrotorque systems, and the integral propel drive are given close attention.

Jan 1, 1972

By D. R. Jolley

"The selection of equipment for open-pit mining is an important decision which results in a considerable capital expenditure by the operator. The decision is complicated by the wide product range on the market. Certainly, equipment performance is an important criterion to consider in making the decision. Equally important, however, is the operating inter-relationship among the equipment. A poor balance increases production costs and waiting time as queues form at the bottlenecks. This inter-relationship is dependent on equipment performance, but it is also affected by management decisions (i.e. scheduling techniques).The purpose of this paper is to show how the computer is used to decide which equipment and operating decisions achieve the required production objectives at least cost. Actual mining of the pit is simulated over a period of time using different equipment and scheduling decisions. Production, waiting time and costs are evaluated for each alternative until the operator is satisfied that he has achieved the best result."

Jan 1, 1970

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By B. D. Sparks, I. E. Puddington, F. W. Meadus

The continuous separation of bitumen from Athabasca tar sands, with a high clay content, has been demonstrated. Recoveries of 95 per cent or higher have been obtained. Further processing of this product, to produce an accept-able type of crude oil, would require less heat than currently used in the hot-water process. Also, by comparison, substantial savings in equipment and operating costs are indicated.

Jan 1, 1971