Search Documents

By W. T. Martson

ABSTRACT Sooner or later, every producing mine faces the question of fill. This paper invites consideration of mill tailings as an economical, efficient, and quantitatively adequate source of such fill. Some of the advantages, disadvantages, methods of utilization, and methods of treating mill tailings for sand recovery are covered. ADVANTAGES AND DISADVANTAGES OF SAND FILL DISREGARDING economic com-promise, that material which supports the greatest applied load with the least compression is the best choice for fill. Table I, reproduced from U. S. Bureau of Mines Bulletin 60, is offered as evidence of the adequacy of hydraulically placed sand. Table II gives the results of tests made in an effort to determine the reason for the difference between load hearing qualities of dry-placed and hydraulically-placed sand. From these, it would appear that hydraulic placing gives a denser initial packing, with corresponding higher, and faster development of, load bearing qualities. Assuming this to be true, then if sand from mill tailings can be placed underground economically, it is the superior fill material. Table III summarizes cost data available. The most cursory glance through the available references (2, 5, 6, 7, 8, 9) will show .that the major benefit from the adoption of sand fill is a decrease in the non-productive fill ?cycle of a working place. This, it is estimated, increases the output of an individual stope by from 25 to 50 per cent. The advantage of reducing the number of required working places for a constant daily production is obvious.

Jan 1, 1951

By L. D. Eccleston

Any man-made structure will eventually decay, but we are basically concerned with the prevention of corrosion within a fairly limited time span. How corrosion can be minimized by design, the removal of oxides and a careful choice of paint systems is discussed, and mention is made of the electrical nature of most anticorrosive systems. Also discussed are the characteristics of certain paint binders and how mechanical properties will differ for various environments. Corrosion of a substrate by acidic breakdown products of some paints is mentioned in conjunction with a discussion on convenience versus ultimate performance. A brief mention is made of the three main components of a paint system, and the principal types of paint are placed in broad categories, with the main strength and weaknesses of each type listed.

Jan 1, 1979

By Sean Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by using assets more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the ?productivity paradox,? where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the true source of benefits is in how effectively IT is used. Most business sectors have accepted that the reengineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors but unique operational processes. The lessons of changing business practice in more common business processes such as inventory control and customer-supplier relationships can be adequately transposed into a mine. The unique operational processes in mines, in turn require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manger training simulators. This paper reviews the latest IT products and ou lines the processes and kinds of change that will be required in order to benefit from these new investment options.

May 1, 2002

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By G. Grassmück

The question of whether the air curtain principle could be used under conditions prevailing in Canadian metal mines was investigated. A vertical, portable BERRY air curtain was tested, at first in a wind tunnel built at Ecole Polytechnique at full scale (8-by 8-ft cross section) to simulate a drift and its lateral connections, and then in the haulage ways of a metal mine under actual conditions. The results permit us to predict under what conditions this type of air curtain is capable of acting as an air stopping or flow regulator and how it could be further developed.

Jan 1, 1969

By Charles Camsell

At the Annual General Meeting of the Institute in 1924. I endeavoured to present the position held by the mineral industries in the commercial life of this country. The facts and figures were presented at that time in a detached way. Since then, however, I have made some attempt to analyze them in order to determine the causes for that position and to draw some conclusions as to the future of the mining industry. As everyone knows, our trade figures are very often used in political discussion, especially in discussion of tariff policy. It would be entirely out of order for me to say anything touching the tariff issue and I want to have it clearly understood that, in my opinion, the material I am about to present contains not a single statement or conclusion which anyone would be warranted in using as an argument for either a lower or a higher tariff or for tariff changes of any kind. As a starting point, let me re-state, very sketchily, Canada's general situation in external trade. In the last calendar year, 1924, we sold Canadian merchandise of all kinds to other countries to the value of $1,045,000,000 in round figures. Our purchases abroad reached about $893,000,000. Thus our sales exceeded our purchases by roughly $152,000,000. In other words, we had what is known as a 'favourable balance of trade' - one of the biggest favourable balances we have ever had in our history. The proceeds of our sales of Canadian products enabled us to meet the bills for all our purchases of foreign commodities and, in addition, placed a large surplus to our credit with which to offset our interest charges and other obligations abroad.

Jan 1, 1925

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By Elmer Palmer

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large ?state of the art? concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By G. R. Webber

CHEMICAL AN AL YSIS by x-ray emission spectrometry has become increasingly important during the past few years. The method is analogous to optical spectrography ?with x-rays being used instead of light and should not be confused with methods of x-ray diffraction used? for identification of minerals and chemical compounds. X-ray emission spectrometry has many advantages for both qualitative and quantitative analysis. Its optimum concentration range is higher than that of the optical spectrograph, and the group of elements which can be detected is not identical to that which can be detected by the optical spectrograph. Elements which can be detected by the x-ray spectrometer are those elements from magnesium (atomic number 12) to uranium (atomic number 92) in the periodic table. The lightest elements in this range have low sensitivities and more specialized equipment is necessary for their detection than for the heavier elements. A large number of applications of x-ray analysis have been directed toward the analysis of ores, metallurgical products, and related materials (see References at end of paper). A more complete bibliography is presented in the Norelco Reporter, Vol. 3, 1956, pp. 37-39. The periodicals Analytical Chemistry and Applied Spectroscopy are a good source of current articles and references.

Jan 1, 1957

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By J. Buckle

"Recognition of the diamond potential of the Wawa subprovince was initially determined from regional data using a kimberlite model. The world’s largest stable Precambrian craton, the Superior Province, is considered to be favourable for the emplacement of diamondiferous kimberlite. The Wawa area is located near the intersection of intra-craton structures visible in the regional magnetic data.The Enigma project is located north of the town of Wawa in northern Ontario. From field evidence and background research, it became obvious that in the Wawa area there were at least two potentially diamond-hosting events, Archean lamprophyric volcaniclastics and Proterozoic kimberlites. The host lamprophyric rock does not contain the classical KIM signatures. However, to complicate the Enigma, stream sediment samples within 200 m of the diamond-bearing lamprophyre produced a typical suite of kimberlite indicator minerals.The micro- and macro-diamond content of the Wawa lamprophyric volcaniclastic rocks is typically 0.2 ct/t to 1 ct/t, although it can be higher locally. The economic diamond potential of these Archean dykes, sills and irregular lamprophyre bodies is still under-explored (Kaminsky, 2002, unpubl.). Oasis Diamond Exploration is currently exploring the area using geophysical, geochemical, and geological data."

Jan 1, 2002

By N. Ogbonna, D. G. Dixon

Although heap bioleaching has been recognized as an economic alternative for treating low grade mineral ores, the underlying physical, chemical and biological processes involved are complex. A detailed investigation into the dynamics of heap bioleaching processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool - HeapSim. This tool can be of great help in the design and operation of heap bioleaching processes. In this paper, the mathematical model implemented in HeapSim is examined. The model takes into account mineral kinetics, particle level effects, bacterial growth, oxidation and adsorption, gas absorption, pore diffusion, bulk advection, gas balance and heat conservation. Three case studies where the model has been applied are briefly discussed. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists of CIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By R. W. Coburn

The results of field experiments on wells which required stimulation indicated that engineered well-completions will cause an increase in ultimate recovery at reduced costs. Techniques and tools have been developed which can be used to establish well conditions most conducive to successful stimulation. Cementing, perforating and treating are bound together so completely that the success of one phase is completely dependent on the .effectiveness of the preceding phase. A method of determining the efficiency or effectiveness of any given well-stimulation treatment has been derived. Pressure behaviour during a treatment can be analyzed to yield the total percentage of the formation which has been treated.

Jan 1, 1960

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By C. R. Whittemore

PROGRESSIVE industrial organizations have recognized the importance of maintaining an adequate reference library of volumes covering all phases of their particular branch of industry, but it has been the experience of the writer that few engineers know how to use to the best advantage this store of extremely -valuable information which has been accumulated for their service. Nor does the average engineer appreciate the fact that it is only through the current technical literature that he can keep abreast of the rapidly developing fields of engineering. The present-day ramifications of the engineering field are of such wide scope that the human mind is not capable of storing away more than a small fraction of the information available on any particular topie; yet, from time ? to time, such information would prove invaluable. An engineer can know intimately only a small part of his own branch of engineering; but he cannot afford to neglect to take the fullest possible advantage of all that is already known in his own particular field. Technical information may be obtained by one or more of the following methods: (1) by enquiring of the individual who knows; (2) by performing the experimental investigations necessary to ascertain the facts; (3) by consulting the technical literature, where a record may be found of the work of others. This last method is the one we wish to examine. Our main consideration is the question of how to use the library, but first it is necessary to give some attention to the kind of enquiries one takes to the library, and to the nature of the sources of information available.

Jan 1, 1938

By F. A. Forward

Introduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product' (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world's nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By G. Van Weert, O. Wang

ABSTRACT: When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Jan 1, 2011

By G. Van Weert

ABSTRACT When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Aug 1, 2011

By K. Howard Poulsen

Shear zones are tabular tructures which tend to occur either discordantly within, or concordantly along the margins of, competent rock masse uch as plutons, sill or flows. They contain deformed equivalents of their host rock and are common sites for gold mineralization localized in tructure oriented y tematically relative to the shear zones and internal linear fabric. Apan from genetic implications, hear zone analysis proves useful in exploration for this type of deposit because the zones are generally wider and more continuous than associated mineralization and because there is an element of predictability to mineralization geometry (i.e. vein orientation. plunge).

Jan 1, 1986