Search Documents

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By D. S. Salonine

Aluminum alloys are widely used in modern industry. Tubes and hollow shapes give great opportunities for structural purposes as well as fluid transport due to their stiffness and lightness, Extrusions on a mandrel or through a bridge die, that requires splitting of the billet with re-welding, produce hollow shapes with varied contours, fins and multiple cavities. Moving and stationary mandrels, mandrel lubrication, tooling for ribbed-tube heat exchangers, and for drilling pipes are considered. Bridge dies can be classified by the bridge position relative to the die face, by mandrel support structure, and by assembly type, The main parameters influencing the quality of the die-welded seams are considered, The difficulties of extruding various alloys through bridge dies are discussed in terms of metallurgical factors, Some approaches to the calculation of the stresses in a bridge are presented.

Jan 1, 2005

By François Robert

The rate of new mineral discoveries in Canada has been declining in the last two decades. In response to the challenge and to stagnating investments in mining-related R&D, twenty Industry partners, supported by PDAC and Natural Resources Canada, established in 2010 the Exploration Innovation Consortium (EIC). This Consortium seeks to promote the discovery of new resources in Canada through coordination and sponsorship of industry-focused innovative and collaborative research and technology development, as well as training and education in mineral exploration. The two main themes of the integrated R&D program focus on exploration targeting in Deep and Mature Environments and in Remote and Covered Terranes.

May 1, 2011

By F. K. McKean

Introduction The present paper may be considered as a sequel to a paper, A Process for Cleaning Molybdenite .Concentrate, which was presented by the author at the annual meeting of the Institute last year. In that paper, a description was given of the laboratory work leading up to the adoption of a new process for treating complex molybdenite ores of the Molybdenite Corporation of Canada. A bare outline of mill performance with the new flow-sheet was included. With this writing, the purpose is to describe the highly interesting work of translating laboratory experience into mill practice, to show what changes were required in design to put the scheme on an operational basis, and to point out the gratifying improvements in mill products which resulted from the new procedure. The process has been placed in operation at the La Corne mine of the Molybdenite Corporation of Canada. This mine was operated during the war by Wartime Metals Corporation, and, earlier, by the Molybdenite Reduction Company, which installed a small plant. The property is situated on the highway from Amos to Val d'Or, Quebec. The claims held by the Company are at the boundary between La Corne and Vassan townships.

Jan 1, 1947

By Jie Zhou

Mining mobile equipment is becoming larger in order to lower operation cost and increase productivity; however, their performance characteristics are often limited by the tire capabilities. Although considerable progress has been made in the field of tire research, the lack of comprehensive knowledge on tire performance characteristics impedes the advancement of off-the-road tires. Longer haul roads, and a severe operating environment make tires more vulnerable than other components of a vehicle. Furthermore, due to a limited availability of large tires, mines are facing shortages. Thus mines and tire service companies are keen to improve tire performance, extend tire life and hence lower operating costs. This paper reviews the relevant tire performance research, analyzes tire interactions with the surrounding environment, tire maintenance practices and operational issues using a case study based on data collected during an ongoing project with Fountain Tire.

May 1, 2006

By W. A. Lang

RESEARCH has been defined as the link between the present and the future. Science, wonderful though its achievements may be, has but scratched the surface of the unknown. Research is directing its attention to winning new facts in order that their application to the processes of today may open up new sources of wealth for the common benefit. Two classes of research investigations are often recognized-fundamental and applied, but these classes merge into each other and it is often hard to distinguish one from the other. Fundamental research is carried out primarily to develop basic facts, but frequently these are found to have immediate economic value, while applied research, specifically aimed at economic values, often necessitates a preliminary fundamental investigation. Both are essential and both should proceed by scientific method. It is obvious in fuel technology that a knowledge of the physical and chemical constitution of the various coals is fundamental to their industrial utilization, and further, a knowledge of the way these coals react under different conditions of temperature, atmosphere, etc., is necessary in solving such problems as storage, combustion, carbonization, gasification, or con-version to liquid fuels. The wide range of coals, the complexity, of their constitution, and the many uses for coal, makes fuel research no simple subject but one with unending possibilities. The Research Council of Alberta, formerly known as the Scientific and Industrial Research Council of Alberta, was established in 1919, to promote the development and conservation of the natural resources of the Province. The work of the Council was arranged in six major divisions: Fuels; Geology; Road Materials; Soils; Natural Gas; and Forest Products. The office and laboratories are located in the University of Alberta. The Council was financed until the depression of 1933 by a separate vote of the Legislature, but since then has been continued, though on a much smaller scale, as one of the activities of the University. It might, however, be noted that although the Council is now in abeyance, a skeleton organization has been maintained so that it can be brought back to active service as soon as conditions warrant. Annual reports are still submitted to the Legislature. Funds have not been made available, however, for the publication of the last five reports.

Jan 1, 1942

By P. Kostuik

"Recent interest in the pipeline transport of solid mate-als has been sparked by the idea that, in an inflationary onomy, pipeline costs are more stable than the costs of any other transport systems. Pipelines have proved over 1e years to be dependable, records indicate that main-•nance and operating costs are comparatively low, and 1eir amenability to automation is of considerable im->rtance.The concept of hydraulic hoisting of solids from under-round, or cross-country hydraulic transportation of con-~ntrates and ores, is currently of prime interest to the ining industry. In general, this paper deals with a preliminary investi-ation of energy losses incurred while transporting a rela-vely heavy, crushed mine product, namely magnetite, oth vertically and horizontally. The basis and validity of everal equations derived by other experimenters to com-ute these losses is discussed. A theoretical analysis of ydraulic hoi:,,ting is made, and, based upon test results, calculation of horsepower requirements for hoisting an re under a given set of conditions is presented. Results indicate that:n vertical transport, the friction head losses are identical to those of clear water, and the total energy requirement for hydraulic hoisting then becomes a function of height of lift, concentration and specific gravity of the solids being hoisted. .-In horizontal transport, friction head losses can be calculated with reasonable accuracy using Bonning-ton's correlation curve. Losses computed utilizing Durand's correlation (K = 85) result in estimates which are too low by 10 to 30 per cent, an<l those calculated using Newitt's correlation (K = 1,100, K = 66) give friction loss values which are too high by 10 to 30 per cent . . -The theoretical horsepower (RMS-hp.) required for hoisting hydraulically is approximately half of that required for conventional double-drum skip hoisting."

Jan 1, 1966

By Gorzalczynski. Stan

The recent trend in underground mine developments is ?big is better?. This is most certainly evident in the mine shaft and the conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed for the past fifty years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident, remains conceptually unchanged from Elisha Otis? design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha?s invention with the last major design change occurring in the late 1940?s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment but also, an increased awareness toward safety.

May 1, 2002

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various complex ore deposits and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides and other phases for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay & Gorain, 2014; Chattopadhyay et al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2017

By L. E. Djingheuzian

"IntroductionIN 1940, in a series of articles, M. W. von Bernewitz(l) reviewed in detail roasting of gold and silver sulphide ores and concentrates. Since that time some significant developments in roasting have taken place, and a number of papers have appeared in the Canadian technical literature, dealing severally with the roasting of a particular ore or concentrate.The purpose of this paper is not only to review some of these Canadian papers and bring the information on Canadian roasting practices to .date, but also to analyse the mechanism of roasting. Hence, it is proposed to start with a study of physico-cl1emical factors fundamental in roasting, the knowledge of which, by creating a sound basis for a proper roaster design, makes good roasting possible.Physico-Chemical FactorsRoasting can be defined as heating sulphide ores in presence of air below fusion points of the constituent minerals, at such temperatures as to convert metallic sulphides to oxides. Hence, roasting is a chemical process.The object of roasting is, by changing, chemically, mineral constituents of sulphide ores, to make the economic recovery of the desired •Constituent metal by a subsequent standard treatment possible. For instance, pyritic ores, containing gold in sub-microscopic form which no amount of grinding would release, are roasted in order, by oxidizing the sulphides, to open up their structures to such an extent as to enable cyanide solutions to come into contact with the gold and dissolve it. The production of porous calcine is, therefore, the object of roasting of refractory auriferous sulphide ores or concentrates. Such a porous calcine may be defined as a desirable calcine, and the roasts which produce desirable calcines can in their turn be termed desirable roasts."

Jan 1, 1952

By Juergen Antrekowitsch, Stefan Steinlechner

"Within the last decades, mainly the base metals, like zinc, copper and lead were recycled from different industrial residues without taking into account that accompanied minor side-elements are often also present. A high supply risk for critical raw materials derives mainly due to the high share of the worldwide production in a limited number of countries. Examples include indium and germanium in China, PGM in South Africa and Russia or cobalt and tungsten in the Democratic Republic of Congo. By taking the market of critical metals into account, the recycling of potential residues does not only contribute to an economic treatment but also to the European strategy to decrease the supply risk of certain metals. Depending on the metal discussed, political unrest, decreasing primary resources leading to supply risks in different countries or also simply economic interests moved these mentioned side elements and with this the residues where they are present in, into the focus of the recycling industry.Because of this, the typical routes of lead, zinc and copper production are evaluated concerning generated residues and their typical contents of contained minor elements. Finally, the paper tries to answer the questions how a possible treatment of these wastes could contribute to the overall supply of for example silver but also other minor elements."

Jan 1, 2016

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of &apos;bumps&apos; and &apos;outbursts&apos; have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By R. O. Burt

The original flowsheet of the TANCO mill consisted of a simple two-stage gravity circuit for the recovery of the tantalum concentrates. With decreasing grade and grain size of the tantalum minerals, considerable modifications to the circuit have been required. This paper discusses the various recent improvements carried out 011 all stages of the flowsheet, which have resulted in a 10% increase in recovery. Future improvements, including on stream analysis, and the possibility of tantalum flotation , are also discussed.

Jan 1, 1979

By N. W. Bliss

"Bauxite has been the almost universal ore of aluminum for about 100 years, with most of the world's reserves oc¬curring in the developing countries. As a result of fiscal and political activities prompted in part by the energy crisis, the formation of the IBA combined with increasing freight and labour costs, these reserves are no longer as competitive or as secure as they once were. This has given fresh impetus to the development of processes for alumina production that utilize raw material other than bauxite. Canada has no bauxite and it is prudent to look for alter¬native raw materials within our own boundaries suitable for one of these processes.Of the three igneous rocks that have been used as a source of alumina, only anorthosite is considered as a potential source in Canada. The Al content would be extracted by a sinter process, which currently requires a raw material with a. minimum of 28% Al2O2. Thus, about 4 tons of anorthosite and 10 to 12 tons of limestone are needed to produce one ton of alumina. There are two petrologically distinct types of anorthosite, one containing the plagioclase andesine-labradorite and around 26% Al2O3, and the other containing upwards of 30% Al2O3, in by¬townite-anorthite; for our purposes they may be con¬sidered as low- and high-alumina anorthosite respectively. The high-alumina anorthosites are somewhat rare; the low-alumina anorthosites are much more common, partic¬ularly in Eastern Canada. Geologically speaking, there is no shortage of anorthosite in Canada. The reserves are im¬mense, although their low Al2O3 content coupled with con¬siderations of location, access and proximity to limestone could be constraints to their development. Fly ash from coal-fired thermal power stations and nepheline syenite can also be used in a sinter process, but neither is likely to be utilized in Canada in the immediate future.The H+ process utilizes an acid attack to leach Al from a raw material with at least 20% Al2O3. One of the best raw materials is kaolinite-bearing clay; not only is it high in Al, but most of it can be extracted. With the possible exception of the Whitemud clay in Saskatchewan, Canada is apparently deficient in clays with sufficient reserves to support an alumina plant utilizing the H+ process. Low-alumina clays with illite and montmorillonite may also prove to be a suitable raw material if advantageously sited with respect to industrial centers. The average shale con¬tains only 15% Al2O33, much of which may be contained in minerals, such as feldspar, not amenable to acid leaching. If shale is used as a source of alumina, it will be because it contains some other valuable commodity, such as oil or uranium, the extraction of which leaves the spent shale upgraded in extractable Al2O3 and lowers the over-all costs to a point where it is economic, Thus, rejects from coal washing plants are most commonly considered as a source of alumina; they are already mined, are available in large and ever increasing amounts, and may contain significant amounts of combustible material which upgrades the Al2O3, content of the resulting ash. Coal rejects from existing and developing coalfields in Alberta and British Columbia are a possible source of raw material, but present data indicate they may contain insufficient Al2O3."

Jan 1, 1976

By B. Karnath, K. Guha, S. Tandon

At Jhagadia Copper Ltd (India), Copper is produced through secondary route using Top Blown Rotary Converter (Kaldo Furnace). The basic raw material being treated includes Matte-slag Reverts, Copper Cakes, dross & Cement, Oxide Ore, Low S bearing Concentrates & various metallics along with high grade copper scraps. The plant has capability to refine & produce Blister grade copper from Kaldo furnace as well as PS Converter . Blister is fire refined in Anode furnace & electro refined in Refinery to produce cathode copper. Our product , Copper Cathode , has already been established in the market as its quality is better than &apos;LME Gr&apos;. The paper deals with the experiences encountered during commissioning & stabilization of the plant.

Jan 1, 2007

By Matthew P. Wickham

The use of existing mine records in conjunction with an appropriate classification scheme can be used successfully to identify and characterize the composition of existing waste rock facilities where traditional approaches based on sampling may be impractical or costly. This paper describes an alternative approach used in an acid rock drainage investigation at a porphyry copper mine with numerous waste rock dumps of varying ages and composition. The approach integrated detailed lithologic and mineralogic information about the ore body and overburden materials with records of pit development and dispatch. A waste rock characterization matrix was developed for the site to meaningfully classify lithology and mineralogic composition of the waste rock. The approach resulted in a focused geochemical testing program and facilitated interpretation and application of the test results.

May 1, 2002

By D. R. Keck

"SINCE the .Canadian Chemical Company has no direct connection with mining operations, and I have had no experience with mining, there is little I can tell you that you do not already know. However, we have had considerable experience with certain types of metallurgical problems and I would like to discuss with you some of these problems and their solutions by our metallurgists.In order to acquaint you with the type of plant and processes to be employed at Edmonton, I would like first to take a few .minutes to trace briefly the history -of the Canadian Chemical Company's affiliate, The Celanese Corporation of America. In the early •part of the twentieth century, two young Swiss brothers, Camille and Henri Dreyfus, received their P.h.D. degrees in chemistry. They were extremely interested in work which was being carried on at that time to find a suitable synthetic fiber that could compete with natural fibers, both quality and price-wise. Early man-made fibers were both coarse and hard to dye. The Doctors Dreyfus• poured all their earnings into research and ultimately developed cellulose acetate filament. During World War I, the Dreyfus brothers were invited to the United States to produce cellulose acetate 'dope' for airplane wing coverings. Dr. Camille Dreyfus built the first American plant for fiber production at Cumberland, Maryland, in 1924.Due to resistance of textile mills to the new fibers, Celanese was forced to set up its own dying, weaving, and finishing mills to prove the new materials. Through the years, however, this operation has •been retained primarily for fabric development purposes,.. with the majority of the acetate being sold to other textile mills."

Jan 1, 1953

By Laura Mottola

This paper outlines a framework for ensuring the success of the implementation phase that follows research and development of new mining technologies and systems. It is based upon recent and past lessons learned that have demonstrated the critical challenges to effective technology transfer, which frequently receive inadequate attention within the culture of the mining business. The paper focuses on mining automation implementation challenges and then outlines a Roadmap which is proposed as an integrated framework to deal with the key aspects of people, process and technology. This framework is built upon: assembly of a Strategic Team to develop a Roadmap; fully understanding the business requirements of the technology initiative; defining Key Performance Indicators in a Balanced Score Card; performing a Stakeholder Analysis to identify the affected groups; and finally developing a master Project Plan to execute the Roadmap.

Oct 1, 2009

By B. Wasmund, M. Y. Solar, I. Candy

The nickel laterite industry is divided into two camps when it comes to the grade of the ferronickels produced. One group, led by Falcondo and Cerro Matoso, markets high-grade ferronickels in the range of 35 to 40% nickel, while another group, led by SLN and the Japanese smelters, favour lower grades in the range of 20 to 25%. Because the ores processed by these smelters vary widely in terms of nickel content and iron to nickel ratios, it is probably more accurate to classify these smelters in terms of their iron recovery: Falcondo and Cerro Matoso smelt at lower reduction potentials and thus recover only 15 to 30% of the iron in their ores, while SLN and the Japanese smelters are very reducing and recover 45 to 65% of their iron. Low reductions generally imply higher slag losses and lower nickel recoveries, but also lower power and reductant requirements; higher reductions, the reverse. The question is, therefore, whether an economically optimum ferronickel grade exists for processing any given ore. This paper proposes a methodology for determining this optimum grade and concludes that nickel laterite smelters should favour low reductions and production of high-grade ferronickels.

Jan 1, 2008

By William Pitman

Ground instability and subsequent rock falls are a major concern in underground mines. As a result, several mining companies are conducting risk assessments of the ground support installed in their mines. Risk assessment is now commonly used to provide mine operators with a systematic process to assess the strategic risks that could lead to injury to personnel or loss of production, and evaluate possible risk control measures. Risk assessments can be carried out to identify major hazards, assess the likelihood of occurrence and consequences of each hazard and estimate the level of risk. This process allows assessment of possible remediation actions to minimize the risk and likelihood of occurrence or mitigation of the consequences to a level that is reasonable and practical. This paper presents two practical mine applications of qualitative risk assessment of ground support to highlight the benefits of this process. Yearly or bi-yearly risk assessment of mine excavations can assist mine operators in prioritizing resources and areas that require support remediation. In addition, it provides a mechanism for proactive response to reduce potential risks associated with personnel safety, equipment safety and environmental impact. It also provides a baseline against which changes in ground condition can be compared and quantified.

May 1, 2004