Search Documents

By G. S. Dobby, J. A. Finch

"I. INTRODUCTIONA significant development in flotation over the past few years has been the increasing industrial use of flotation columns, primarily in Canada. The column differs dramatically from conventional mechanical flotation machines, both in design end operating philosophy, which has been a principal reason for its slow acceptance by the mineral industry. Boutin, Tremblay and Wheeler (1. 2) developed the concept in the early 1960's and since then plant and laboratory columns have been marketed commercially by Column Flotation Company of Canada Ltd. In 1980-81 at Mines Gaspe, Quebec, three columns replaced 13 conventional cleaners in a molybdenum upgrading circuit, with superior results (3). Since then many of the copper producers in British Columbia have installed columns for copper and molybdenum cleaning, including Gibraltar, Lornex, Highmont and Island Copper. There now appears to be widespread interest in flotation columns.The column is particularly attractive for applications involving multiple cleaning stages and can upgrade In a single stage compared with several stages of mechanical cells. This results in simpler, more controllable circuits. Importantly, the column itself is well suited to computer control. A significant problem, however, has been that of translating laboratory data to plant performance. The purposes of this communication are to address the problem of column scale-up and to describe some of the transport mechanisms of a flotation column, leading to a kinetics based model.A schematic of a flotation column is shown in Figure]. Industrial columns are up to 13 m high and 0.3 to 1.8 m in cross section (either square or circular). Three zones can be identified:a collection zone, with feed entering 2 to 3 m below the top of the column and descending against rising bubbles generated at a gas sparger; a washing zone, where a packed bubble bed is generated by a downward flow of wash water; and a conventional froth (2 - 5 cm thick), the sole purpose of which is particle transport to the launder. The tailings withdrawal at the bottom of the column is controlled at a rate slightly greater than the feed flowrate (called a positive bias).An important element is the washwater, added just below the froth zone. The component of the washwater that flows downward (to make up the bias) is sufficient to prevent coalescence of rising gas bubbles. The packed bubble beg so generated is very efficient at suppressing gangue entrainment to the concentrate."

Jan 1, 1985

By J. T. Kalala

The High Pressure Grinding Roll (HPGR) is gaining acceptance in the mineral processing industry and has become a competitive technology in reducing the specific energy consumption in Mineral processing plants. The amount of samples required for HPGR amenability testwork and HPGR wear tests is usually high and often cannot be available at early stage of projects were only a few drill cores are available. Although HPGR was initiated from small scale piston die compression tests, the development of small scale piston die test to predict the performance of HPGR has been slow. The objectives of this paper was to present the designs, operating procedure of piston-die press and operating conditions which have resulted in similar particle size distribution obtained from a piston die test and HPGR Labwal unit starting from the same feed size distribution. Testwork were conducted using a 2 MN piston-die press and a Labwal HPGR unit on major South African ore types, viz, gold, platinum and iron ores. The results obtained show that piston-die test can generate data to predict energy consumption, product size distribution, and even to evaluate the edge effect.

Jan 1, 2012

By W R. Honeywell

Two series of laboratory flotation tests were carried out to study the treatment of Faraday ore by two-stage flotation. First the acid-consumers and then the uranium minerals were floated. On ore ground in the Faraday mill grinding circuit, and using Faraday mill water in the flotation step, a recovery in the flotation concentrate of from 91 to 93 percent of the uranium was obtained in 45 to 50 per cent of the weight at a grade of 0.24 per cent U30s. The saving of acid in leaching the uranium-bearing flotation concentrate, as compared to leaching the whole ore, ranged from 30 to 46 per cent. The average over-all extraction resulting from flotation and leaching of the flotation concentrate was 88.1 per cent. The best collector for the acid-consumers was sodium oleate. Acintol F A-1 emulsion was the best collector for the uranium minerals, and, in the uranium flotation step, an acid pH in the slurry was found to be necessary. The reagent costs were estimated to be 22 to 26 cents per ton of ore.

Jan 1, 1963

By H. Watari

In 1998, a voluntary agreement was reached between the European Commission and the European Car Manufacturers Association (ACEA) to reduce average carbon dioxide emissions of new cars to 25% below 1995 levels by 2008, Agreements have also been reached between the European Commission and the Japanese Automobile Manufacturers Association (JAMA) and the Korean Automobile Manufacturers Association (KAMA), However, the target average of carbon dioxide emissions of less than 140g/km in 2008 is a very challenging goal, Therefore, total product weight reduction is an objective for many manufacturers, This can be achieved utilizing materials possessing high strength and low weight, One material that has recently attracted interest is magnesium alloys, The magnesium alloys are expected to play an important role as next-generation materials, which have possibilities of contributing to lighten the total product weight when magnesium products can be used to replace aluminum and mild steel products.

Jan 1, 2005

By Paul M. Clifford, David M. Baird

The Great Northern Peninsula of Newfoundland consists of a Precambrian core of gneisses and granitic rocks, cut by numerous diabase dykes. This complex is surrounded by an envelope of sedimentary rocks of Cambrian to Carboniferous age. Radiometric dates from two granite masses in the core give a mini-mum age of -945 m.y. (Grenville) for the last major tectonic activity. This Grenville deformation conferred upon the core substantially its present structure which has controlled later events to a marked degree. Block movements of the core, dominantly in a vertical sense, have ex-posed it to erosion at intervals. The nature and distribution of the flanking sedimentary rocks and the present relief of the peninsula suggest four such movements. THE Great Northern Peninsula extends some 150 miles north-northeast from the northwest corner of the main body of the island of Newfoundland. It separates the Gulf of St. Lawrence from the Atlantic Ocean, except for the 12 mile wide

Jan 1, 1962

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By Kjell Winther

"Hydralift Scanmec introduced early in the eighties a new and different mill design for very large grinding mills. The design described has actually no size limitation upwards and is so far suggested with motor power up to 40 MW. The mill is furnished with gearless ring motor drive transmission. It is totally fabricated, without heavy castings. The first installation, an 8, 1 MW ball mill dia. 6,5 m x 9,65 m length, has been in continous operation in 13 years without problems. Total grinding costs has been reduced with 3 0% compared to traditional smaller mills. Reductions has been achieved in maintenance cost, power consumption, liner wear and grinding media consumption.So far 3 ball mills of the described design are delivered and in operation, one grinding Iron ore and two grinding Nickel ore.IntroductionThe design of mills for mineral ore dressing has basically been unchanged since grinding in mills started some I 00 years ago, in spite of the fact that mills have grown larger and larger. This has resulted in structural and mechanical problems, causing expensive failures and loss of production.Hydralift Scanmec engineers were designing mills for more than 20 years according to the old «rules». As they experienced interest for an increase in the mill size at the time when reports about failing mills were published, they started analyzing the different mill parts to find new solutions. One goal was to only use elements from proven technology in the new design. Two key items were ring motor (wrap around motor)(Isch et al. 1977, Meintrup and Klein 1982, Ranze 1983) and large diameter pad bearings (wrap around bearings)(Fuller 1984), both acknowledged from other industries."

Jan 1, 1995

By C. S. Touchard, F. Bourgeois, L. Cassayre, Julcour-Lebigue C.

Developing a hydrometallurgical process that can overcome the refractory nature of chalcopyrite (CuFeS2) to leaching still eludes the minerals industry, despite major research efforts spanning decades. The several leaching experiments of this ore in sulfuric acid tend toward the same conclusion that the precipitation of elemental sulfur or iron containing species are the main dissolution inhibitors. Describing both the electrolyte composition and the various solid phases in equilibrium for the Fe-H2SO4-H2O system is essential to overcome this issue and to find an operating window. According to the thermodynamic models and to the thermodynamic data, we demonstrate, in this study, the need to use the Specific ion Interactive Theory (SIT) model to describe complex electrolytic systems through a limited number of parameters. Hence, the binary interactions for our case study have to be defined and estimated. This work develops a methodology to determine these parameters of the SIT model up to 90°C and an acid concentration of 1 mol/kg from published data for H2SO4-H2O and Fe(II)-H2SO4-H2O sub-systems or from new experimental data for the Fe(III)-H2SO4-H2O one. This method will eventually be applied to copper systems to lead to a thermodynamic description of the complete CuFeS2-H2SO4-H2O system. INTRODUCTION A leaching process consists in the dissolution of a solid phase into an aqueous medium in order to extract compounds of interest. It is a key step in the hydrometallurgical processes used in the primary production and recycling of metal components. One of the main leaching issues is the formation of passivating layers on the surface of solid particles, whose consequence is a partial or total hindrance of the dissolution. The leaching of chalcopyrite (CuFeS2) in sulfuric acid is a prime example. No industrial solution for the atmospheric pressure leaching of this ore has been developed to date because of passivation phenomena caused by the formation of elemental sulfur or iron-containing precipitates on the surface of the particles (Li, Kawashima, Li, Chandra, & Gerson, 2013). In the 1970s, the Pourbaix diagrams established for the Cu-Fe-S-H2O system at 25°C for low concentrated solutions (Garrels & Christ, 1965; Peters, 1976) agreed that copper and iron are fully dissolved at high potential and in acidic medium (pH < 4). However, they neglected the many stable solid phases that can form in these conditions. In addition, the Pourbaix diagrams of chalcopyrite in water, calculated with two recent databases (FactPS and Thermoddem 2017) associated to FactSage and PhreeqC softwares respectively, show large discrepancies at 75°C (Figure 1). Indeed, at high potential, FactSage predicts the formation of goethite FeOOH at a pH value of 1, while PhreeqC predicts the formation of jarosite (H3O)[Fe3(SO4)2(OH)6] for pH greater than 2.5.

Jan 1, 2019

By A. Demirci, A. Keçeciler, Y. S. Durutürk

"This paper deals with the results of the variation of thermal conductivity of rocks with pressure on a laboratory scale. For this purpose, the authors have added a pressure-supplying unit to the apparatus developed by Mousset-Jones and McPherson (1986), Önder (1995), Ashworth and Ashworth (1979), and Innaurato and Occella (1989) in order to measure the thermal conductivity under pressure. The values obtained from the tests performed by this new apparatus have been stated using a regression analysis and the related graphs have been drawn. Results have shown that the thermal conductivity of rock varies digressively with pressure. The same results have been obtained in different rocks types. IntroductionOne of the most important tasks of mining engineers is that of establishing, maintaining and sustaining safe and healthy working conditions in underground mines.Heat can have a profound effect on safe and healthy working conditions and is one of the main problems in deep underground mines. In this regard, the temperature of the air passing through the mine openings increases steadily and causes a decrease in the efficiency of workers due to the unwanted physical effects to human bodies in the working area. At the same time, the hot and humid environment resulting from heat and temperature rise causes some important occupational diseases and increases the accident risks in the related openings."

Jan 1, 2002

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By J. E. Gillespie

Introduction Mineral wool may be defined as "rock, slag, or glass fibres made by a process of melting and blowing by steam or air, containing a minimum of oil and unfiberized material" (U.S. Bureau of Standards CS 117-44). The earliest production of the material was in Wales, about one hundred years ago. In the United States, the industry daces from 1870 when a plant, using slag as raw material, was established in Greenfield, New Jersey. It was not until 1897, however, that large-scale production was commenced on this continent at a plant in Alexandria, Indiana, which utilized rock from nearby deposits. Today, mineral wool is manufactured in many parts of the United States and Canada, the plants for the most part being in close proximity to deposits of suitable rock or to sources of slag. In the United States there are some seventy-five producers with a total annual capacity of nearly one million tons of wool. In Canada, in 1946, eleven manufacturers produced about fifty million square feet of batt-type mineral wool insulation material. Mineral wool is, perhaps, the most efficient of all heat-insulating materials and, moreover, it is fireproof, extremely durable, and insect- proof. Its high efficiency is due to the very low thermal conductivity of the fibres themselves and to the fact that the produce as marketed contains up to 90 per cent non-conducting air space. Depending on the degree of compression of the fibres in the manufactured product, the specific gravity ranges from 2 lb. to 10 lb. per cubic foot. Products Marketed Following are the principal forms in which mineral wool is marketed: Blanket. - Mineral wool with or without reinforcing on one or both sides, with various types of confining media, all suitably bound together.

Jan 1, 1948

By P. Tittes, M. Deal, M. Spicher, S. McDaniel, J. Wickens

"Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine’s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine’s history, the metallurgical testing, the flowsheet and discusses design considerations.INTRODUCTIONHaile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching in 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that has delineated over 62 tonnes (+2M ozs.) of gold in reserve at an overall grade of 2 ppm (0.06 opt). This paper provides a brief history of the property, a summary of metallurgical testing, description of the process flowsheet and discusses design considerations.HISTORY1827 – 1837Gold was discovered in creek beds on the Haile property in 1827. The property was owned by Benjamin Haile, and the first few years of production came from placer mining. After gold was discovered in schist beds to the sides of the streams, Haile expanded the operation by leasing 18 meter-square (50 ft.) plots to local planters. These planters used slaves to work the small excavations in the agricultural offseason. The gold ore was taken to arrastras where the free gold was liberated and recovered. The excavations were above the water table, generally less than 18 meters (60 ft.) down, and it was noted then that gold could be found embedded in sulfides and difficult to extract."

Jan 1, 2013

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world&apos;s largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

By B. Samanta

Abstract - Ore reserve estimation, based on sparse drill hole data, was conducted for a placer gold property in Nome, Alaska. A problem with sparse data is that random subdivision of the data into modelling and evaluation subsets (as is commonly done) becomes a problem, as random selection may result in biased/skewed subsets. Therefore, a technique that combined data segmentation with genetic algorithms (GA) was applied to divide the samples into three equivalent subsets: training, validation and testing. Data segmentation was done on the basis of the distribution of gold values. Neural network and a variety of kriging techniques were used to estimate gold grades. A multi-layer feed forward neural network along with "early/quick stop" training was used for neural network modelling. A comparative evaluation of kriging and neural network methods was then performed. The results revealed that neural network was generally superior to the kriging techniques for gold grade estimation in the Nome deposit.

Jan 1, 2002

By B. Pewkliang, K. Ehrig, E. Macmillan, M. Smith, V. Liebezeit, Y. Li

The Olympic Dam iron-oxide copper-gold (IOCG) uranium-silver deposit is the largest publicly declared uranium, fifth largest copper and third largest gold resource. Currently, the operation consists of an underground mine and integrated processing plant. Uranium is produced from leaching of flotation tailings and is a co-product to copper cathode with by-product gold and silver bullion. The Olympic Dam geometallurgy team began studying ore from the Southern Mine Area (SMA) in 2006 and soon discovered uranium behaviour was far more variable than the behaviour in the Northern Mine Area, which had been mined from the start of the operation in 1988. The primary objective of Olympic Dam geometallurgy is to develop metallurgical performance predictors that reliably describe the process performance of different ore types and distribute these into the resource block model for use as a fundamental input into mine planning. The nature of the uranium mineralisation (compositionally and texturally complex and highly variable) meant that classic mineralogy techniques alone could not provide the resolution required for prediction of uranium extraction. However, the combination of quantitative mineralogy, results from laboratory-scale leach tests and modelling within the geometallurgy program has enabled prediction of both uranium flotation recovery (via association with sulphides) and uranium leach extraction, including at variable leach conditions. These stope-based predictions have supported trade-off decisions between operating costs and uranium revenue, and have predicted the changing recovery as the mining operations have moved into the Southern Mine Area in recent years.

Jan 1, 2020

By D J. Murray

This paper outlines the principles of friction hoisting and the components involved, and gives a description of a specific mine hoist. Friction hoisting is compared with conventional drum hoisting, and the depth of shaft at which friction hoists become more economical than drum hoists, with respect to power consumption, is determined. Introduction T HE purpose of this paper is to outline the principles of friction hoisting, to describe the components and to show the advantages of multi-rope friction hoisting. Some calculations are made to show that the power requirements and the initial costs of friction hoists are less than those of conventional drum hoists, once a certain depth of shaft has been reached. The use of multi-rope friction hoists is gradually superseding the employment of the conventional drum hoist in many parts of the world. It results in heavier payloads from deeper levels, an increase in shaft safe-ty and a more compact installation for protection against adverse weather conditions. It was observed that where drums and friction sheaves exceeded 30 feet in diameter, a number of mechanical disadvantages were being experienced;

Jan 1, 1965

By L. C. Lien

Tower crane layout (TCL) is a typical construction site layout (CSL) problem, which is suitable for a wide range of work assignments and site conditions. Tower crane is one of the key facilities for vertical and horizontal transportation of materials, especially for heavy prefabrication units such as steel beams, ready mixed concrete, prefabricated elements and large panel formwork such as machinery and equipment, and a wide variety of other building materials within a construction site. However, it is a difficult combinatorial optimization problem to determine the locations of tower cranes with materials quantity supply and demand for engineers. Swarm intelligence (SI) was very popular and widely used in many complex optimization problems which was collective behaviour of social systems such as honey bees (bee algorithm, BA) and birds (particle swarm optimization, PSO). This study applied a hybrid swarm algorithm namely particle bee algorithm (PBA) based on a particular intelligent behaviour of honey bee and bird swarms by integrates theirs advantages. This study compares the performance of PBA with BA and PSO for a proposed hypothetical construction engineering of TCL with materials quantity supply and demand problem. Results show that PBA performs better performance than the mentioned algorithms on a proposed hypothetical TCL problem.

Aug 1, 2013

By Lian-Jin Tao

With fast development of China modernization, road construction obtains great achievement. However, in the construction process of highway, especially the high-grade highway in mountainous area, there are many unavoidable high cut slopes. Specifications for Design of Highway Subgrades, China, prescribe that the design scheme of slope with height more than 30m should be compared with bridge scheme and tunnel scheme economically. In spite of the existing guidelines, it is still quite common to see many high slopes due to engineering geological conditions, highway line shape, cost and issues related to traditional design ideas. Actually the traditional way with ?high backfill, the high cut? for mountainous highways seriously damages the original ecological environment and groundwater system, especially to those area with weak ecology, where the damage is unrecoverable. It is quite common practice to use artificial vegetation for cut slope virescence, however it still has problems such as low ratio of survivor, high maintenance cost and lack of species diversity. Now people are more and more aware of the importance of ecological environment, it becomes urgent to decrease the damage to ecological environment after ensuring the stability of high slopes. With the aim to reduce ecological damage, we proposed a new design approach which is ecological environment friendly by decreasing cut slope height with steep excavation scheme. This approach requires that (1) the geological condition is good, and the rockmass can be sTable itself; (2) excavation should not badly damage the rock, which means blasting must be controled by using buffer blasting, smooth blasting and pre-splitting blasting; (3) if local geological condition is not very good, excavation should have intervals for one bench, the advised space is 20m; (4) to ensure the slope stability in construction process, the cut slope should be reinforced more strongly than usual and in time. Finally, the deformation of the slope and the working condition of the reinforcement structure should be monitored to ensure the slope stability. The new design is used to a roadside cut slope of provincial trunk highway S223 in Guangdong Province. Based on intensive geological investigation and borehole tests, it is found that the slope rock mass is intact and sound, and the rock strength is quite high. Results from numerical modeling by UDEC reveal that compared with the traditional design scheme with 90.23m high slope, the steep scheme with only 23.46m high is characterized by its relatively large deformation and stress concentration, however the influenced area only appears at the upper slope and tends to sTable. With cable reinforcement, the stability of slope excavated steeply can be guaranteed. Deformation of the slope and the cable force are monitored in details in the period of construction, which show that the deformation of the slope decreases gradually and the final deformation is very small, and the cable tensions change small after the cables were tensioned. It is optimistically estimated that the steep slope should be sTable during operation. Comparison analysis between the steep scheme and the common scheme affirms that the steep excavation is better than the traditional scheme in terms of ecological environmental effect, slope height, the excavated amount, the excavated quantity of slope surface, engineering cost. It is concluded that if geological condition permits, the steep cut scheme should be used with better benefits.

May 1, 2009

By P. N. Saavedra, E. A. Salamanca

"The maintenance strategies in the mining industry are changing from operative and periodic inspection strategies to a condition-based, predictive maintenance strategy centred in vibration analysis plus complementary techniques. Condition monitoring can also help to improve availability by being able to pinpoint and diagnose problems on operating machinery at an early stage. This reduces unscheduled downtime and production losses.However, in mining, for shovels operating in transient modes, with variable load and/or speed, the FFT (Fast Fourier Transform) standard approach is not directly applicable for analysis. This work illustrates how spectral order analysis and new transforms, called time-frequency transforms (TFT), allow us to monitor the shovel when it is working. Some practical examples showing the application of these analysis techniques to occasional vibrations measured on hoist and crowd transmission of a shovel are also presented. It is shown that at present, it is possible to carry out the vibration monitoring in the mining shovel while it is working, therefore avoiding the high cost of a loss of production which can occurr in traditional monitoring, where the measurement is taken while the shovel is out of production."

Jan 1, 2002