Search Documents

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By Joseph L. Fournier

Suncor Oil Sands employs delayed coking technology in converting bitumen into synthetic crude oil. Currently up to 10,000 m3 of delayed coke (coke) is produced per day as a byproduct of the upgrading process, of which up to 9,000 m3 per day is placed in dry storage on Lease 86/17. A review was completed to examine the case history of leachate potential experiments from the dry storage of coke and the environmental relevance of coke leachate studies conducted over the past decade. The review included an evaluation of the potential impacts of environmental conditions within the location of coke storage, including precipitation pH, as well as daily and annual ozone trends. Coke leachate potential has historically been characterized using standard leachate testing protocols (i.e., TLCP, SPLP) together with other studies that have employed strong acids and oxidizing agents in the extraction fluids. The present paper highlights prevailing conditions in the Athabasca Valley air-shed with emphasis given to ambient ozone (oxidizers), as well as precipitation pH and acid input deposition rates, and will demonstrate that TCLP / SPLP tests lack the intended environmental relevance relative to the conditions under which coke is stored.

May 1, 2011

By R. E. Phelan

Introduction The Flin Flon deposit was discovered by Tom Creighton, an experienced prospector and trapper, who in 1914 made his headquarters at The Pas, Manitoba, and still lives there. The discovery was made in the fall of 1914, and Creighton and his associates spent the next summer in investigating the find. In August of 1915 the first claims were located. The property was optioned to Hayden Stone & Company, and in the spring of 1916 they started a diamond-drill campaign. Hayden Stone spent $50,000 on the property and, among other things, completed over 7,500 feet of diamond drilling. The ore not being as high grade as expected, and also being complex in character, Hayden Stone then abandoned their option. In the spring of 1917, Messrs. Earle, Faskin and associates took an option on the property and started an extensive drilling campaign. This campaign accomplished approximately 18,000 feet of drilling and secured for the Faskin interests a 32 per cent interest in the property. In 1920, W. B. Thompson and The Mining Corporation of Canada secured an option, and, while this option was in force, sunk two shafts in the ore-zone and did a considerable amount of drifting and cross-cutting in the ore to study the manner in which it occurred in place, and, by actual channel sampling, to check the grade indicated by the previously accomplished diamond drilling. All of this work had indicated that an ore-body existed on the property containing at least 18,000,000 tons of ore, assaying as follows: gold, 0.074 oz./ton; silver, 1.06 oz./ton; copper, 1.71 per cent; and zinc, ). 45 per cent (1). Complete analyses of composites from the drill holes showed that the ore was very complex in character. It contained the above values in gold, silver, copper, and zinc, as well as large amounts of sulphur and iron, and traces of lead, arsenic, antimony, cobalt, and various other metals. Although the ore was obviously pyritic in character, pyritic smelting, the usual method of treating this class of ore, could not be used to beneficiate the ore with any reasonable expectation of making such a venture a financial success, since coke and coal landed at Flin Flon would be expensive, and siliceous flux was known to be scarce locally and low in grade. The property therefore lay idle until 1925.

Jan 1, 1935

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability.The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employees to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed. IntroductionThis article is the second of three on predictive maintenance at the Louvicourt mine operated by Aur Resources Inc. The first article, published in the October 2002 issue, was about vibration analysis for rotating machines. This article describes how lubrication and oil analysis for stationary machines permitted Louvicourt to save more than $150,000 within two years and presents the evolution of the oil analysis program.Louvicourt mine, located near Val-d’Or, Quebec, is a copper and zinc mining and milling operation that processes 4300 t/d of ore and employs 289 people. Production began in 1994. Louvicourt mine is a partnership between Aur Ressources (30%), Teck Corp. (25%), and Novicourt (45%)."

Jan 1, 2003

By E. Viljamaa

In this research, earlier developed information integration method and novel web technologies are applied to intensify infrastructure construction process control. The applied method uses semantic methods to integrate scattered information that is later on exploited by process management using state-of-the-art web technologies. The applied method and web technologies not only improve the process management situation awareness by integrated up-todate multi-source process data but also provide platform independent access and visualization tool for process data. Utilization of such technologies potentially lead on cost savings, make processes safer and also more environmentally friendly. The integration method also enables intelligent queries to the integrated data making possible to use machine based inferring to the data.

Aug 1, 2013

By G. Major-Marothy

"INTRODUCTIONA beneficiation plant to upgrade earthy iron ores is being installed by the Iron Ore Company of Canada in Sept-Iles, Quebec.The crude ore for the plant will come from the Knob Lake area, located in Northern Quebec, where mining has been in progress since 1954.Some 170 million tons of ""direct 11 ores have been mined and shipped in the past eighteen years, with an overall silica content of 7 to 8 percent. No beneficiation - except the reduction of the top size to about 2 inches - took place during this period, but extensive research work has been carried out, in order to find a feasible process.Since “washing"", gravity separation, roasting and magnetic separation experiments did not indicate positive enough results, flotation was tried and found to be feasible.The beneficiation complex being installed will consist of grinding, flotation, dewatering - i.e.: thickening, filtering and drying - balling feed preparation, and agglomeration - i.e.: balling and induration.This process will result in a product superior to the ""direct shipping"" ores and will also expand the ore reserves by allowing material with a higher silica content to be utilized.THE OREThe Knob Lake ores are grouped by mineralogical composition and by grade.BLUE ORES, representing roughly two thirds of the reserves, carry their iron content mostly in the form of massive, blue hematite and martite.YELLOW ORES, about one sixth of the reserves, have predominantly hydrated iron oxides as the iron bearing minerals.RED ORES, the other sixth of the reserves, carry the iron mostly in the form of red hematite.The gangue in all ores is mainly quartz, but aluminum oxides and hydroxides are also present, particularly in the red ores."

Jan 1, 1972

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the 'bumps' which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By Kathleen A. Altman

"This paper supplements the information provided annually at the Canadian Mineral Processors Operators Conference regarding the education of Mineral Processors in Canada. The purpose of the paper is to provide information regarding the engineering accreditation process in the United States and the universities that offer programs in Mineral Processing and Extractive Metallurgy in the U.S.There is a critical shortage of trained Mineral Processors and Mining Engineers world wide. The Society for Mining, Metallurgy and Exploration (SME) formed a task force to evaluate the national needs for trained engineers and to track the number of engineers who graduate from U.S. universities each year. The statistical information for Mining Engineers is well-developed. The current effort is to assemble similar information regarding students who graduate with expertise in Extractive Metallurgy and Mineral Processing as well as to explore the limitations of the accreditation system in the United States and its impact on the education of Mineral Processors. The long-term objective is to develop a data base regarding Mineral Processing programs and Mineral Processing graduates that is as complete as the one that has been maintained by the Canadian Mineral Processors.INTRODUCTIONIn the United States engineering curricula are accredited by ABET, which was formerly known as the Accreditation Board for Engineering and Technology. The objective of ABET accreditation is to ensure that educational programs in applied science, computing, engineering and technology meet quality standards set in conjunction with the professional organizations that represent professionals in the industries which hire students graduating from those educational programs. For example, the Society for Mining, Metallurgy and Exploration (SME) is the lead society for accrediting Mining Engineering programs in the U.S. For Materials Science and Metallurgical Engineering programs, the lead society is The Mineral, Metals and Materials Society (TMS). SME is a cooperating society for accrediting Metallurgical Engineering programs. Cooperating societies for the accreditation of Materials Engineering include the National Institute of Ceramic Engineers (NICE), the American Institute of Chemical Engineers (AIChE) and the American Society of Mechanical Engineers (ASME)."

Jan 1, 2008

By Eric Schraml

Wardrop Engineering and the Placer Dome?s Campbell Mine Design Team utilized leading edge directional raise boring techniques and an innovative, remote controlled application of steel fibre reinforced shotcrete ground support to achieve improved mine ventilation and a superior, safety focused secondary emergency egress. While more standardized methods may have provided a sufficient solution to either the requirement for a ventilation raise or for a traditional escape ladder way, innovative methodology ensured both objectives were met with a single, enhanced solution. Placer Dome committed to provide a solution that minimized energy consumption, optimized air delivery and facilitated an escape way focused on minimizing the negative physiological aspects associated with mine evacuation. The project was successful in providing a new airway, returning 47 m3/s (100,000 cfm) from the 39 Level to 30 Level, minimizing risk to the raise equipping crew and providing a fully equipped escape hoist. The resulting secure escape environment provided an efficient means of evacuating personnel working at depth without necessitating a potentially dangerous exhausting climb to surface. The project has substantiated, that optimized safety focused design can be achieved without jeopardizing project economics.

May 1, 2002

By E. Bongajum

We present results from petrophysical studies to characterize a Zn-Pb-Ag deposit in Nash Creek, New Brunswick. The measurements are part of an integrated study that includes geological and geophysical data acquired on the property. In order to successfully characterize the ore body, an understanding of the relevant physical parameters and their change with vertical and lateral variations of the target lithology is necessary. The quality of the estimated 3D variation in the physical properties is supported by the presence of several boreholes that randomly span the survey region. Density was measured from cores of thirty-two boreholes across the area. Seventeen of these boreholes constitute two intersecting borehole profiles, which is ideal for locally modeling the 3D distribution of the ore deposit. High densities (>3.2g/cm3) correlate strongly with Zn-rich mineralization zones (low resistivity). Compression and shear wave velocity measurements made from representative core samples of the regional geology range from ~2.91 to ~6.41 km/s for P-waves and from ~1.41 to ~4.20 km/s for S-waves. The lower bounds of these velocity values correspond to regions with a high degree of alteration. Moreover, porosity estimates from rocks on the property suggest that porosities range from 0.35% to 11.79%. Induced polarization (IP) measurements confirm that mineralized samples show a significant chargeability and resistivity contrast with respect to the host rock. Thus, chargeability and resistivity information can be combined to adequately identify conductors associated with mineralization in electrical survey data. Information on these physical parameters and their 3D statistical distribution have serious implications on various aspects of mineral exploration that include: resource estimation, choice of geophysical data acquisition and interpretation, and information for preliminary rock stability assessment.

May 1, 2009

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By I. Nakatsugawa

Chemical conversion coating is a process to create thin oxide/hydroxide film containing several inorganic/organic compounds by way of chemical deposition reaction. In case of the application to Mg mobile electronic housings, the film should possess a good electric conductivity while keeping adequate corrosion resistance and working as a paint base. The use of toxic/hazardous chemicals is strictly prohibited from the environmental aspects. This paper describes the recent trend of conversion coating used for Mg electronic housings and analyzes critically from the point of surface technology. The importance of cleaning process and understanding of surface microstructure are particularly emphasized with several experimental results.

Jan 1, 2006

By A. Vien, B. C. Flintoff, R. P. Edwards

"A major thrust in industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements in control performance can be achieved by getting back to the basics.IntroductionEvery modem concentrator has a state-of-the-art computer control system in place. Several of these are contemplating installing, or have installed, advanced control systems, such as expert systems, but the foundation of their control system remains the PI controller. Although the authors are not aware of any survey or published information for the mineral processing industry, it is reasonable to assume that it would be similar to the pulp and paper industry. ""The average [pulp] mill has some 2000 control loops of which 97% use PI control. This means that PID, dead time compensation, adaptive controllers, specialized algorithms, ... , constitute only 3% of the installed base."" (Bialkowski [1992]).Bialkowski [1992] also stated that ""If you have been keeping score, only 20% of the loops surveyed actually decrease variability in automatic over manual mode of operation, in the short term."" He attributed the problems to: poor tuning (30% of all loops), control valve problems (30% of all loops) and process problems (20% of all loops). There appear to be a serious need to go back to basics and review the existing control system."

Jan 1, 1998

By John G. Payne

The Pebble deposit contains three contiguous zones. In the Pebble West zone, granodiorite stocks intrude gently warped volcanosedimentary rocks that had been intruded by diorite sills and two felsic intrusion breccias. In the Central zone, volcanosedimentary rocks are cut by diorite and granodiorite sills; the latter are genetically associated with the granodiorite stocks. In these zones, widespread potassic alteration consists of brown biotite and K-feldspar, with abundant quartz-carbonate-sulphide vein stockworks. Chalcopyrite/pyrite ratios range from 2/1 to 1/20. Diorite hosts the highest-grade mineralization, with much of it being disseminated. Patchy, later phyllic alteration is moderate and commonly depleted in copper. The Pebble East zone occupies a granodiorite stock and intruded host rocks below an eastwardly thickening wedge of barren Tertiary volcanic and sedimentary rocks up to 600 m thick. Brown biotite alteration and copper mineralization are strong, with chalcopyrite/pyrite ratios commonly over 1/1. The zone extends to a depth of at least 1200 m below surface; some drill holes bottomed in strong mineralization. Later, weak to moderate sericitic alteration removed some chalcopyrite and locally remobilized gold. The Pebble deposit has a Measured/Indicated resource of 3 billion tonnes grading 0.28% Cu, 0.32 g/t Au and 0.015% Mo (= 0.5% copper-equivalent) and an Inferred resource of 1.13 billion tonnes grading 0.30 g/t Au, 0.27% Cu and 0.015% Mo (0.55% copper-equivalent). The Pebble East zone has an Inferred resource of 2.13 billion tonnes grading 0.55% Cu, 0.34 g/t Au, and 0.037% Mo (0.97% copper-equivalent). The Pebble East zone is open to the east and to a lesser extent to the north, south, and to depth.

May 1, 2006

By Jayne Somers

Methane (CH4) is a potent greenhouse gas, accounting for 15 percent of all global greenhouse gas emissions in 2005. Since methane has a much shorter atmospheric lifetime than carbon dioxide (CO2), reducing methane emissions can achieve considerable climate benefits over the next 25 years. Coal seams often contain significant quantities of methane and CH4 released to the atmosphere from gassy mines during coal extraction is a major source of greenhouse gas emissions. Methane (CH4) emissions from coal mining activities constitute approximately 6% of total global human-related methane emissions. Coal mines around the world have recognized that methane is a clean energy resource that can be captured and used productively. Coal mine methane (CMM) is currently utilized for power generation, natural gas pipeline injection, vehicle fuel, industrial process feed stocks, on-site mine boilers, mine heating, and home heating distribution systems. Upgrading mine degasification systems can often improve gas quality and create favorable project economics. The United States has been a leader in coal mine methane (CMM) recovery and use since the 1990?s. There are now 15 projects at active underground mines in the U.S., as well as 26 abandoned mine methane projects. Recovery and use projects at active underground U.S. mines reduced methane emissions by approximately 49 Billion cubic feet in 2010. In an exciting new development, a ventilation air methane (VAM) mitigation project at the CONSOL McElroy mine in West Virginia was installed by Verdeo. Operational since September 2012, this is the first commercial-scale VAM project in the U.S. and the project will reduce methane emissions by an estimated 920 MMCF/yr. As part of the U.S. Greenhouse Gas Reporting Program, actual data on methane emissions from underground coal mines was collected for the first time in 2011 and reported to U.S. EPA in September 2012. The data collected will help inform stakeholders, particularly the underground coal mining industry, of CMM emission sources on public and private lands. The detailed data will also shed light on the specific sources of methane from active underground coal mines and highlight project opportunities for the U.S. coal industry. The paper will cover U.S. coal mine methane emissions, U.S. CMM utilization and destruction projects, Federal policies and State incentives for CMM capture and utilization. 2011 CMM data from the U.S. Greenhouse Gas Reporting Program Subpart FF will be analyzed and compared with previous U.S. Greenhouse Gas Inventory estimates. Other developments, including the voluntary carbon market, will be discussed.

Aug 1, 2013

By Frédéric Bélanger, George P. Demopoulos, Pascal Coursol, Thomas Feldmann

"The use of scandium in industrial applications is expected to rise in the coming years, in large part due to the expected adoption of new, clean energy technologies such as solid oxide fuel cells or Sccontaining high strength aluminium alloys. Given that the supply of Sc is currently dominated by only a few countries (Russia and China) other sources for scandium extraction need to be investigated. This paper looks at different options for the recovery of scandium from waste solutions generated during the production of TiO2 pigments via the chloride process route. In particular, a direct solvent extraction (SX) approach and possible options for concentrating scandium before the SX step were investigated. It was found that the presence of Ti during solvent extraction causes severe formation of stable emulsions, which can complicate the successful application. This was particularly a problem after multiple contacts of the organic phase with fresh aqueous phase. On the other hand it was noticed that the presence of certain elements in the solution, e.g., iron, could possibly be utilized to concentrate scandium in a solid precipitate.INTRODUCTIONMany newly developed high-tech products depend on the use of chemical elements that are only produced in very small quantities. This can result in high and fluctuating prices, as can be seen from Figure 1, which may cause substitution with inferior alternatives, if possible at all (Reck & Rotter, 2012; US Dept. of Defense, 2013; Whittaker, 2011). One example is scandium (Sc) a member of the extended rare earth element family. There are only a few scandium ore deposits, but most Sc is produced from the processing of by-products of other metallurgical processes (Melcher & Wilken, 2013). Increasing demand for scandium metal and oxide (Sc2O3, scandia) is coming from its increased use in applications such as ceramic lasers (Li, Ikegami, & Mori, 2005; Rainer et al., 1982), high strength aluminium alloys (Lathabai & Lloyd, 2002) as well as solid oxide fuel cells (SOFC) (Thijssen, 2011). Especially, the spread of climate friendly SOFC’s, which are a commercial product today (Bloom Energy, 2014), is expected to be a main driver for future Sc2O3 demand. However, the rate of market penetration of this green technology depends on the availability of high purity Sc2O3 (>99.999%), since it specifically contributes to longer life-time and better safety of the SOFC’s (Bloom Energy, 2014; Irvine, Politova, & Kruth, 2005)."

Jan 1, 2016

By Kevin Bell

About Beltek Inc. For more than a decade Beltek, Inc. has been working with national and international organizations to harness and deliver solutions which gain real ebusiness advantages in today's world. Our objectives are to partner with our customers to achieve maximum results, while reducing costs. At Beltek, we provide a commitment to you and your organization's needs. Whether that be delivered by ensuring our services and products are state of the art or by providing a level of personalized service, which makes you feel like the center of attention, Beltek is about adding value to every job we work on. The individuals who work at Beltek quickly become your friends because we share your passion and enthusiasm for the business we are in. That's why every person is a leader in his or her respective fields. Having these individuals as apart of our business ensures you get the best out of our equipment, receive the very latest in advise, problem solving and support. We also pride ourselves on our ability to remain flexible at all times because we know deadlines and schedules can change quickly, so we always go the extra mile to deliver exactly what you need.

May 1, 2004

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By Manqiu Xu, Glen Robertson, Steve Wilson, Pete Quinn

"The middlings circuit, once called the pyrrhotite rejection circuit, at Inco’s Clarabelle mill was a single flotation stage. It used to process a combined feed consisting of the main flotation scavenger concentrate and the non-magnetic portion of the magnetics flotation circuit tails. The typical circuit metallurgy was 55% nickel recovery at 6.5% Cu+Ni concentrate grade. In the past few years, a research project with the objective of improving the circuit metallurgy was initiated between Inco’s research laboratory and the Mill’s Process Technology group. This project has gone through three steps: a) initial laboratory studies, b) on-site pilot plant investigation, and finally c) full plant implementation.The present paper describes the initial laboratory test work. The development of a two-stage circuit consisting of separate rock and pyrrhotite rejection stages to replace the simultaneous rejection of both rock and pyrrhotite in a single stage is discussed. A two-stage circuit simulation based on batch laboratory flotation data is also presented. Further development work, including the on-site pilot plant test work and the plant implementation of the new circuit design, will be described in a later publication.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill, Copper Cliff, Ontario processes a rich complex sulfide ore from several large production mines around the Sudbury basin (Agar, 199 1). The sulfide mineralization is simple, consisting of chalcopyrite (Cp), pentlandite (Pn) and pyrrhotite (Po). The main gangue minerals are pyroxene, feldspar and quartz with minor amphibole and talc. Estimates of mineral composition are routinely calculated from Cu, Ni and S assays. In the mineralogical calculations, all gangue minerals are conveniently grouped and treated as rock (Rk)."

Jan 1, 2000