Search Documents

By B Bamford

High speed diamond cutting has extensive applications in civil and mining engineering. A project involving the diamond sawing of black granite is investigating the nature of the diamond cutting process. A sawing machine was devised to adjust the cutting load and measure cutting speed. Cuttings were collected for size distribution analysis. The surface produced by interaction between diamond. grits and the rock was subjected to microscopic investigation. Increasing load prompts the proportional increase in the cutting rate. But the mean size of cuttings shows little change. The photomicrographs of the cutting tracks indicate neither patterns of crack formation nor signs of the ductile behaviour of the rock. A diamond cutting model for hard rock is formulated on these observations. Diamond cutting is a process of surface failure, which advances in four stages. The polycrystalline characteristics of a hard rock and the action of high-speed diamond grits guarantee the creation of crack nuclei which develop into cracks in various directions. This network crisscrossing cracks enable the stripping of this surface layer from the rock.

Jan 1, 1992

When we are beset with the economic problems the world faces today, we are always inclined to look at the shorter term future. Today I would like to take a long-term view of our industry, project historical demands for our products into the future and discuss opportunities for our members. Perhaps we could firstly look at the long-term demand trends for our metals. If I tend to use non ferrous metals as a basis for my figures it is because this data is more readily available to me. I am sure that most other products of our industry show similar trends.

Jan 1, 1992

By J Samosir, L Snyman

Northparkes was the first mine in Australia to use block cave mining method which relies on gravity and natural rock stresses to fragment and recover the ore. It was also the first hard rock mine to use hydraulic fracturing, in conjunction with CSIRO, to promote caving of E26 Lift 1. The technique was later used on E26 Lift 2 wedge and E48 prior to undercutting.Northparkes production is currently sourced from the E48 Lift 1 block cave mine and E26SLC. The E48 block cave contains economic ore to the north and south of the current cave footprint. To recover this ore the footprint has been extended on the north and south with two extraction drives and one extraction drive, respectively. Modelling of cavability above the additional drives indicated that the cave would not readily propagate to a sufficient height of draw to mobilise the ore and tended to arch over into the existing cave. To address the modelling results and to reduce the risk of the project, rock mass preconditioning was adopted.This fracturing campaign was performed from surface drill holes adjacent the subsidence zone angled to intersect the higher grade and higher elevation ore zones.Optical televiewer surveys, run prior to fracturing, picked intervals and fault zones to be avoided. Holes were resurveyed post-fracturing to detect newly created fractures and as a measure of success of the program.During fracturing operations water and gel fractures were run at varying depths and pumping pressure was logged for each fracture. The mine seismic system monitored significant events and dye in the fluids utilised for tracking water inflow locations during underground inspections.Towards the end of the project, guar fibres from gel were detected within the mill circuit and required treatment to resume optimum processing.CITATION:Webster, S, Snyman, L and Samosir, J, 2016. Preconditioning E48 cave extension adjacent to an active cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 471–478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Mineral exploration and mining in New Zealand has had almost five years of new legislation. The requirement for different consents is a challenging, time consuming, expensive exercise but in most cases the new procedure is working, although the matter of obtaining access to land is still a major issue. Priority is critical. After lodgment of an application for a minerals permit there are many other matters to address such as identifying land owners, occupiers and administrators, preparation of access applications, consultation and preparation of various resource consent applications.

Jan 1, 1996

Thirty mixed cultures of microorganisms from soil, water and mineral samples from the Groote Eylandt Mining Company mine site were approximately three times more effective in biodegrading manganese dioxide (34± 18 mg Mn++/1/day) than sixteen purified strains (11 ± 10 mg Mn++/1/day) isolated from the primary enrichment cultures. Two pure bacterial genera identified as a Pseudomonad and a Bacillus, with an excess MnOz and nutrient, were able to dissolve 106 mg Mn++/litre/day in mixed culture compared with 29 mg Mn++/litre/day when grown separately.

Jan 1, 1983

In common with general experience in the iron-making industry overseas, Australia has in recent years suffered a deterioration in the physical quality of her iron ores in their suitability as a direct blast furnace feed. The increasing amounts of fines and the more friable nature of lump ore, especially in the ore from the Cockatoo Island deposits in Yampi Sound, Western Australia, have focused attention on problems of ore preparation and agglomeration, particularly sintering.Although very small pilot scale Dwight-Lloyd type sinter machines were operated at the steel-making centres at Newcastle and Port Kembla during World War II, no sizeable capacity was installed, so that ore was charged to the blast furnaces almost entirely unscreened, and the resultant flue dust was stockpiled.Towards the close of the war, the pilot plant at Newcastle was replaced by a small machine, adjacent to the flue dust stockpile, with a rated capacity of some 20 tons per hour. After approximately five months of part-time operation, this plant was closed down in January, 1945. Production was not resumed until December, 1950, when, due to a temporary ore shortage, it was decided to supplement available ore with sinter produced from the large flue dust stocks of about 300,000 tons. In spite of mechanical and process difficulties, inherent to the design of the plant, operation was continued on a two-shift basis, with several shutdowns for extensive overhaul and plant alterations, until September, 1954, when production was put on a three-shift basis. Addition of Yampi ore fines to the sinter machine burden was not commenced...

Jan 1, 1957

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

By E Villaescusa, C Drover

Fully resin encapsulated threaded bar and cement grouted cable bolts are common forms of reinforcement for underground mining excavations constructed at great depth. These elements are frequently installed to dissipate the dynamic loads caused by violent rock mass failure mechanisms. Failure of the ground support scheme without rupture of the reinforcement elements implies that the maximum energy dissipation capacity of the scheme was not utilised. The ground support damage mechanisms are useful to identify in this context as they reveal vulnerabilities which limit the scheme performance. This paper presents a number of field observations of reinforcement performance following a range of dynamic loading conditions. It was observed that fully resin encapsulated threaded bars exhibit variable behaviour. In particular, inconsistent resin encapsulation was frequently observed in combination with surface support failure, indicating that the retention function of these elements may allow preferential loading of the surface support system. Observations of cement grouted, twin-strand plain cable bolts reveal a common mode of damage involving differential displacement across the steel-grout interface and slip of the cable within the borehole. This is common where strands are not mutually tensioned with barrel and wedge assemblies. Surface fixtures that exceed the strength capacity of the cable strand are required in order to minimise the occurrence of this response. Improved load transfer from the rock mass and surface support to the cable can thus be achieved, particularly where small block size failure occurs.CITATION:Drover, C and Villaescusa, E, 2016. Field performance of fully encapsulated reinforcement during violent failure events, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 659–668 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Forecasting, particularly when applied to meaningful issues, is known irreverently as 'futurology'. There is quite a range of opinion ext.ant in the world when mineral resources are looked at. The opinions range from the doomsday view that there will be acute shortages of all essential commodities, to the optimistic outlook that new 'discoveries will prevent any possibility of shortages. The environment is, as yet, only studied locally and quite parochially; surprisingly there is little integration when considering the spatial atmosphere, the seas in depth and the earth's crust.

Jan 1, 1981

By G Marling, A Calderon, J Harris, P Kirsch, M Shi, D Sprott, A Kirsch

Large-scale infrastructure construction needs to comprehensively manage risks that can impact the health and well-being of many people, from workers (temporary, contracted or full time), to families and surrounding communities. This paper starts with an analysis of incidents (injury, fatality, other damage) in tunnel construction between 2000 and 2014 and assesses the distribution of these events by continent, year, and severity of outcomes. These incidents are then analysed and mapped to a framework of hazards derived from RISKGATE (2014). A comparative register of current tunnel construction risk management guidance is derived from current Australian codes of practice and this register is also mapped to the RISKGATE framework of hazards to identify where coal industry knowledge may offer utility to the tunnelling industry.An initiative of the Australian Coal Association Research Program (ACARP), RISKGATE is an interactive online risk management system developed to assist the mining industry in implementing continual improvement in the management of major unwanted events. To date, a comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, outbursts, coal bumps and bursts, human/machine interface, manual tasks, slips/trips/falls, inrush and occupational hygiene. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.This paper proposes and outlines how knowledge within the RISKGATE platform could be applied to managing the significant health and safety risks associated with tunnelling. The authors suggest that to varying degrees the knowledge already captured in RISKGATE is likely to be transferable to tunnelling construction operations. Please note that this paper focuses on tunnel construction and does not address risk management of tunnels in operation (eg road transportation or utility networks).CITATION:Kirsch, P, Kirsch, A, Calderon, A, Marling, G, Harris, J, Shi, M and Sprott, D, 2014. Management of health and safety in tunnelling – application of Australian coal mining knowledge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Uceda, E Guerra, Y Choi, J L. Shepherd

In this paper we describe the leaching characteristics of pure gold in thiosulfate solutions that contain a known chelator; meso-2,3-dimercaptosuccinic acid (DMSA). The interfacial and chemical characterisation of the system was accomplished using both electrochemical methods and inductively coupled plasma mass spectrometry (ICP-MS) analysis after pure gold samples were exposed to solutions composed of 65 mM Na2S2O3, 1 mM NaOH and a range of DMSA concentrations. In the absence of DMSA, cyclic voltammetry revealed the onset of thiosulfate mediated gold dissolution, the degree of which was reduced at more positive potentials due to the formation of oxidised thiosulfate products on the gold surface. The addition of small amounts of DMSA (<10 ¦M) to the electrolyte resulted in minor changes to the voltammograms indicating a subtle interaction of the additive with the gold surface that may improve leaching. However, at higher concentrations of DMSA (up to 100 ¦M), electrochemical evidence suggests the formation of new oxidation products in solution as well as the formation of more compact monolayers of DMSA on the surface, which contribute to partial repassivation of the surface. The influence of DMSA on thiosulfate leaching of pure gold electrodes at the open circuit potential for a period of 90 minutes was tested and the corresponding gold leaching performance evaluated with ICP-MS analysis. Our data shows that small amounts of DMSA (1 ¦M) doubled the amount of total gold in solution when compared to the same study in the absence of the additive. However, higher concentrations (5 ¦M DMSA) reduced the overall amount of dissolved gold. These results may point to a mechanism where small amounts of DMSA improve leaching by adsorbing onto the surface in a highly defective monolayer that partially blocks or disrupts the formation of passivation products caused by thiosulfate oxidation, but excess DMSA can limit the leaching process itself by forming too coherent a monolayer on the gold surface.CITATION:Uceda, M, Choi, Y, Shepherd, J L and Guerra, E, 2013. Investigating the influence of meso-2,3-dimercaptosuccinic acid on thiosulfate leaching of bulk gold electrodes, in Proceedings World Gold 2013 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Real-Time Integration of Mining and Metallurgical Information for Efficient Use of Energy and Water

Sep 13, 2010

The object of this talk is to bring before members the importance of the prospector and the' State Battery system to the wealth and prosperity of the mining industry in particular and the State of Western Australia in general, and to touch on the more important features.Customs plants of any sort are usually subject to a good deal of critioism, usually on the large profits made at the expense of the customer, etc., and this often clouds the real value of the work being done.Prospectors, on the whole, are a good class of men; they work under conditions and difficulties which would deter those less spirited. Food, water and mining supplies are often difficult to obtain and frequently have to be transported great distances. Their mining tools are usually of the most primitive type, yet during last year over 109,000 tons of prospectors' ore were handled by the State Battery system for 73,250 fine oz. valued in Australian currency at over £587,000, the value being 57/- per long ton at par.This production brings the State Battery system into fourth position amongst the producers of the State, the yield being exceeded by the Lake View and Star, Wiluna and the Great Boulder.In passing I might mention that these notes were written at the end of the year 1940, and the above figures were for the previous period. The figures for last year, 1940, were not quite so good, being 101,000 tons for approximately 60,000 fine oz., valued in Australian currency at £572,000.In spite of this drop the State Battery system maintained its position as fourth in order of gold output for the State.The extractions, as a whole, throughout the system, were 92·54%, made up of 68·86% by amalgamation and 23·68% by cyanidation. These figures, for a group of 20 plants treating widely different classes of ore, must be considered satisfactory. The total production since inception is over £11,000,000 in Australian currency.State Batteries are usually more or less of a standard design. Ore is reduced to about 2i in. maximum size before being sent to the bins. Challenge automatic feeeders control the feed to each mill unit, amalgamated copper plates collect the free gold. Corduroy strakes are used with some ores after amalgamation, but in only a few cases has this been found of any advantage to the customer.The pulp from the battery is sampled, after leaving the tables, with a "Tazewell" sampler and pumped to dams for subsequent cyanide treatment.The "Tazewell" sampler is a machine driven by the moving pulp; and takes about fifteen dips per .minute from such pulp through a slotted...

Jan 1, 1941

By S C. Dominy

Grade control programs aim to deliver economic tonnes to the mill via accurate definition of ore and waste. The foundation of a successful program is high quality sampling supported by geology and a suitable data management and modelling system. Underground sampling methods include chip, channel and panel samples; grab/muck pile samples; and drill-based samples. Grade control strategy is related to mining method and orebody type. Sampling protocols must be designed to suit the style of mineralisation in question. Holistic studies focussing on ore mineralogy and gold particle deportment, size and distribution are required for sample collection and preparation protocol optimisation through ‘Theory of Sampling’ application. Where possible, such programs should be undertaken early in the life of a project. Appropriate assaying procedures are also required. Program implementation will require suitably skilled individuals to train and mentor staff, with ongoing Quality Assurance/Quality Control (QA/QC) monitoring and review will allow protocols and staff to be updated as required.

Aug 22, 2011

The Effect of Bulk Iron Concentration on the Copper Activation of Sphalerite at pH 9

Sep 13, 2010

By K J. Davey, J T. Woodcock

Australian steelmakers produce up to 30 000 t/yr of electric arc furnace (EAF) dust. Current disposal techniques include sending EAF dust to landfill, stockpiling, and paying zinc smelters or registered waste removalists/processors to take the dust. Many of the complex overseas pyrometallurgical and hydrometallurgical treatment routes cited in the literature are not considered economic. Governmental, environmental and social pressures on producers to consider more sustainable disposal options are mounting, and there is now a strong push to consider recovering potentially valuable or recyclable components, such as zinc and iron units, from EAF dust. As well, there remain strong economic drivers for producers to find lower cost disposal solutions. Characterisation studies undertaken at CSIRO Minerals have revealed important physical differences in the nature of the zinc- and iron-bearing phases contained in domestic EAF dusts. These differences have been exploited using simple and cheap mineral processing techniques such as water washing, wet cycloning and wet magnetic separation. This has allowed a significant upgrade in the zinc content of EAF dust to be achieved, together with a reduction in the levels of key smelter penalty elements, such as chlorides and fluorides. The zinc-rich portion of the dust is now a more attractive smelter feed while the iron-rich part of the dust could potentially be briquetted or pelletised with a reductant and recycled to recover iron, and thus close the loop on dust processing. The basis of the separations tested together with laboratory results from several Australian dust samples are presented and discussed in this paper.

Jan 1, 2006

By J Player, P Mikula, G Sweby

A numerical modelling back-analysis exercise was carried out at a WA gold mine at which early signs of seismicity (rock noise, scatts from active faces) were becoming apparent as depth of mining increased towards the 500 m mark. Some strain bursting had occurred and it was necessary to discover what the implications of this were for greater depth. The aim of the modelling was to: 1. Establish a correlation between observed ground conditions and model predicted damage, in overstressed areas of the mine. 2. Use this correlation to forecast rock mass damage and ground control requirements for proposed future stoping panels at greater depth. Good correlation has been achieved between observed rock mass damage, and a 3D Finite-Element RS3 model, run in elastic mode. Two candidate stress field orientations were modelled. The model parameter best fitting the observations was the Strength Factor (SF), the ratio of strength/stress. The good match (correlation coefficient of 0.7) between observed and modelled suggests that the elastic approach is justified for the depth range and rock mass properties analysed. The correlation also enabled a link between observed damage and installed ground support performance. Using the linear best-fit between observed and modelled, a forecasting exercise was carried out using the same RS3 model, modified to include future stoping. The resulting damage and ground support categories were obtained from the modelled SF for each proposed stoping level. Also, a series of generic geometries was assessed to investigate the impact of varying stope face lead/lag distance, sill pillar height and stope pillar size, on ground conditions. The key finding of the generic geometries were: • Ground support schemes have been defined for the expected conditions. • All ore drives are expected to have significant damage in the backs and rehabilitation. • Lead/lag distance not to exceed 10 m. • Sill pillar/level intervals of less than 20 m require an increase in ground support scheme. • Pillar sizes for maintaining footwall and hanging wall stability should be at least 10 m × 5 m.

Nov 29, 2022

By R Berry, N Bonnici, K Nguyen, S G. Walters, M Kamenetsky, C L. Evans

Mineral maps produced via optical and scanning electron microscope û mineral liberation analyser (SEM-MLA) automated mineral identification systems are being used to examine the relationships between mineral phases in spatially well-constrained samples of intact and crushed rock. The use of sophisticated image analysis software allows data pertaining to individual or groups of mineral phases to be extracted from the mineral maps. Analyses of the extracted data can be used to identify populations of phases. Data extracted from the images can be compared with mineral processing data, eg hardness, grindability, degree of liberation, from the same sampling intervals, enabling ore characterisation to be linked to processing behaviours in a spatially constrained, quantified manner that can potentially assist with mine planning and optimisation.

Jan 1, 2008

The Influence of Particle Shape in Rock Fracture

Sep 13, 2010

Samples of a refractory copper ore were examined to test their response to segregation roasting, flotation, and acetonitrile leaching. Recoveries in the segregation roasting stage were between 60 and 100 per cent, while flotation recoveries varied between 60 and 85 per cent in cleaner concentrates assaying 25-40 per cent copper.The fraction of the copper which could be leached from the concentrate by an acetonitrile/sulphuric acid/cupric ion leach solution varied from 16 to 97 per cent, the lower recoveries being correlated with the presence of sulphide in the concentrate.

Jan 1, 1973