Search Documents

By P D. Munro

The spatial distribution of ore with similar processing properties or domains within an orebody may be identified early in the assessment of an orebody to provide a sound basis for later development of the orebody. The assignment of domains in the primary sulfide portion of an orebody is often more difficult than recognition of the oxidised, supergene and related domains usually located towards the top of the mineralised volume. This paper will discuss some approaches to assigning domains within the primary sulfide portion of an orebody. The processing properties of each mining block will be known if the contained domain(s) and their proportions are known. The use of both physical and chemical ore properties to assign the domains is discussed. The domains based on similar processing properties do not necessarily coincide with geological zones assigned by geoscientists. As part of assessing the physical properties of ore, the modal analysis of the ore with respect to the valuable sulfide minerals and the sulfide and non sulfide gangue minerals has to be known, along with the traditionally used elemental assays for valuable and penalty elements. Two scales for determining other physical ore properties will be considered: the mesoscopic scale (examined by human eye) and the microscopic scale (examined via a microscope under high magnification). The strengths and weaknesses of the data obtained at the two scales are discussed in the paper. Broadly, data collected at the mesoscopic scale are much less expensive but the types of data available are more limited. Methods for evaluation of chemical ore properties are also discussed. After establishing a basis for establishing the spatial distribution of domains, variability testing is required to verify the integrity of the designated domains. In contrast, each block of ore in some orebodies has been assessed principally via the results of a laboratory separation on a number of drill core samples or composites from throughout the block, with minimal or no attention to the concept of domains.

Jan 1, 2008

The papers in this section of the conference and indeed the conference as a whole will rightly focus on the recent û the state of play around the Pacific Rim. However, to set the scene I propose to take a longer-term perspective. In so doing I wish to illustrate and emphasise that change is normal and natural û to paraphrase Bob DylanÆs 1963 classic, æThe times they are (always) a-changinÆ Æ. The challenge is how to cope with such change, in an industry, a corporate and a personal sense. A further challenge for geologists, both exploration and mine-based, and indeed for anyone, is to understand where they fit in the broader picture. For several reasons it is appropriate first to look briefly at the minerals industry in the Pacific Rim around a century ago. It was here in Adelaide in April 1893 that the first general meeting of the Australasian Institute of Mining Engineers (or The Australasian Institute of Mining and Metallurgy as it later became) took place and where the Centenary Meeting was held in 1993. The late 1800s and early 1900s was a period of extraordinary change in the minerals industry regionally and worldwide. The industry benefited from the economies of scale provided by improved mechanisation. It further benefited from the introduction of technically qualified professionals, such as chemists, metallurgists and mining engineers, although the usefulness of geologists had yet to be recognised commercially. With the rise of such professionals, technical societies formed and flourished. At the same time international financial markets and trade were expanding, a gold standard was widely supported and the financing of mining ventures was well established. Mining was an international business and its people travelled widely. As a consequence of the better-educated mining professional, the ready exchange of knowledge and the availability of finance, new processing techniques such as pyritic smelting, the cyanide process and flotation were developed. These, together with much improved materials handling in the mining and processing phases, dramatically changed the economics of the minerals industry.

Jan 1, 2004

By G Steward

Gravity Leaching of high-grade gravity gold concentrates, such as Knelson Concentrates, with the ACACIA Reactor represents a new generation of concentrate treatment methods. The ACACIA Reactor is a complete packaged plant for the maximising of gold recoveries from gravity gold concentrates. This paper will introduce the process technology and provide process results from the Porgera ACACIA Reactor installation. The advantages of the ACACIA Reactor are many, and justification for installation has been varied. The typical advantages of the process include: increased recovery of gold from the Knelson Concentrate; no return of high-grade table tails, often grading several thousand g/t, into the mill circuit; reduction in tails grades of slow leaching gold; reduction in the requirement for operating staff by the removal of the manual tabling process and replacing with a fully automated treatment system; improved security by removing the tabling step where operating staff come into direct contact with visible gold; improved health and safety, by the removal of the treatment steps for the table concentrate, which often include operators handling corrosive chemicals and the production of sulphur and arsenic compound fumes; and improved metallurgical accounting, by allowing daily head grade calculations. The ACACIA Reactor was developed by Anglogold for Union ReefÆs Gold Plant and has been in production for over two years, and has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, there are now four full installations of the processing plant, including Anglogold Union ReefÆs, Anglogold Sunrise Dam, PACMIN Carosue Dam and Porgera Joint Venture.

Jan 1, 2002

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

In November 1992, the Internal Revenue Commission (IRC) was formed from the rperggr of the Papua New Guinea Taxation Of- fice (PNGTO) and the Bureau of Customs, and now has the re- sponsibility for the administration of direct and indirect taxes on a national basis in Papua New Guinea (PNG). Since that date we have undertaken many initiatives to make the new organisation more efficient and responsive to clients' needs. Income Tax The mining industry is catered for, in respect of income tax, un- der a separate taxation regime within the Income Tax Act (ITA), Division 10, as well as some general provisions within that Act as may be applicable. Division 10 is itself broken up into subdi- visions to cover the different types of mining leases, namely Spe- cial Mining Leases (SMLs) and Mining Leases (MLs), and peri- ods of time during which those sub-divisions apply. Ring Fencing Income tax assessed on the mining industry, with the exception of Mining Leases (these will be explained later), has a project basis of assessment, that is, each project is assessed separately as if the taxable income of the taxpayer from operations attributable to the project was the only assessable income derived by that taxpayer. This is often referred to as "ring fencing". This is an important point to consider because losses from unsuccessful projects cannot be set off against income from those that are suc- cessful, except in very limited specific circumstances, such as where an unsuccessful exploration licence is cancelled or surren- dered. The project basis of assessment applies to both resident and non-resident companies. A relaxation in the 'ring fence' provisions was applied from 1st January 1995, where ten percent of exploration expenditure, in- curred in areas outside of Special Mining Leases and Petroleum Development Licences in a particular year of income, can be claimed as an outright deduction which is limited to ten percent of the tax otherwise payable in that year. This was introduced to encourage exploration in PNG.

Jan 1, 1997

By L E. Setiawan

The mining and milling groups at Batu Hijau are tasked with increasing SAG mill throughput by approximately ten per cent. Avenues used for this process are blasting and crushing optimisation, ore blending and predicting SAG mill throughput in relation to the geological model. This is in line with traditional æMine to MillÆ studies. At Batu Hijau, mill and mine sequencing cannot readily be configured to perform the surveys traditionally required by a æMine to MillÆ study while meeting the daily production target of 140 000 tonnes per day and processing from varying ore types in one pit. A program called BOCCOST (blasting optimisation crushing conveying optimising SAG throughput) has been implemented to capture approximately 200 variables from blasting, mining and milling operations and assign them to a common point in space in the geological model in real time. Interpretive analysis of data from BOCCOST is used to model relationships between the 200 variables to determine which and how these factors affect SAG throughput. Once these relationships are determined, the blasting, ore blending and crushing process can be optimised to generate a product that maximises mill throughput. The relationships modelled from BOCCOST are also used to generate a SAG mill throughput estimator, which can be coded into the production block model. The block model can be reconciled with the geological block model for correlation by geological domain. Once this relationship is established, SAG mill throughput domains can then be established for predicting SAG mill throughput. This SAG mill throughput estimator is then used in conjunction with revenue calculations to determine an ore cut-off, which combines these two elements to maximise metal production.

Jan 1, 2002

The mining industry was one of the first to be directly regulated by legislation in the 19th century when British public opinion was mobilised by reformers seeking social change. In the next wave of mining safety legislation, account was taken of technological advances in the industry, but again, the amendments were in large measure driven by public expectations following a series of disastrous mining accidents with great loss of life. The result was the prescriptive and detailed type of regulation that has, to a great extent, remained with and become a way of life in the mining industry of today. In 1970, the then British Government appointed Lord Robens, a former Chairman of the National Coal Board, to head a Committee of Inquiry to consider the arrangements then in place for preserving the safety and health of people at work and to consider and make recommendations on the need for change in the legislation governing such matters. The result was the 1972 report Safety and Health at Work which, in turn, resulted in the Health and Safety at Work etc Act 1974 (UK). This Act, which embodied the now familiar concepts of consultation with the workforce on matters relating to health and safety and the statutory application of the previously existing Common Law concept of the duty of care, became the model for much occupational health and safety legislation in many places around the world, including the various States of Australia. As a result of the `Robens style' of legislation, the regulators of the mining industry have had the opportunity to become less prescriptive and to introduce an `enabling' style in their statutes. This has not always been welcomed by the industry which has, to some extent, missed the comfort of knowing exactly what is required of it in order to ensure compliance with the legislation while appreciating the `self-regulatory' opportunities that the new style of regulation offered.

Jan 1, 1995

By D A. Williams

The conventional method of transporting mine tailings from a process plant to a tailings storage facility (TSF) is in the form of a low to medium density1 slurry, which can be pumped using centrifugal pumps. Over the past several decades, therefore, mine operators have generally adopted this default approach. There are, however, some convincing arguments why consideration should be given to thickening the tailings slurry to a higher density paste consistency. In particular, the minimisation of environmental impacts, the reduction in water consumption and the cost savings relating to TSF closure make paste an attractive option for the life of mine tailings disposal. There are several environmental impacts that are associated with a conventional slurry TSF, such as land sterilisation, aesthetics, dust, seepage and acid mine drainage. Some of these impacts, such as dusting, may be difficult to mitigate while the TSF is in operation. Others can be influenced by adjustments made to the tailings slurry density at the plant. Unplanned fluctuations in slurry density and/or viscosity can have a significant influence on TSF performance and can exacerbate the environmental impacts relating to the facility. Relatively minor changes in the solids content of the slurry can affect tailings beaching behaviour, degree of segregation, position of the phreatic surface, amount of freeboard, consolidation behaviour, placed (settled) density (and hence TSF capacity) and in situ strength of the tailings. Paste is a non segregating slurry and many of these effects can be minimised at the TSF when the tailings slurry is thickened to a paste. These improvements are manifested by reduced seepage, flexibility in selecting an appropriate final landform, ability to rehabilitate progressively and reductions in plant water usage. It is possible to minimise environmental impacts of a TSF through the use of tailings paste. Ideally the paste production plant should be part of the initial design of the process plant. However, significant benefits can be gained by adding a paste production plant at some time later in the operational life of the mine to reduce environmental impacts and facilitate an environmentally acceptable TSF closure.

Jan 1, 2002

The perception of the mining industry in the Australian community has changed considerably over the last four decades. This has been partly brought about by changing values and expectations of the Australian community as well as by global factors. The legal environment for the Australian mining industry has undergone significant changes. Among them, the High Court's Mabo decision which confirmed native title rights as part of the common law and environmental legal developments are dealt with particularly. It is suggested that the Australian legal environment is not necessarily the prime cause for Australian mining companies taking their investment off shore. This is a summary on how native title impacts on land tenements and some of the major issues that emerged since the `Mabo decision' and the Native Title Act 1993 are discussed. Environmental legal developments have resulted in liability facing directors and senior management in compliance matters .and in operating mining and other businesses because of changes in community expectations. In the next decade it is suggested there will be many drivers for more changes in the legal environment. Some of these are touched on including the changing roles of the Commonwealth and State Governments, the High Court as -law-makers and the changing relationships with indigenous people in Australia and in overseas countries. The changing legal environment for mining demands a national approach in many areas on the proposition that resource based industries are part of a national industry. The uniform law approach among the States has been taking place but this needs to further. An appropriate task force should be forward to review the entire legal structure and regulations affecting mining on a national rather than a State basis . The mining industry will need to work with expectations of a changing community which have powerful, but sometimes contradictory, interest groups.

Jan 1, 1997

By K Gottliebsen

Many hydrometallurgical and chemical processes produce large amounts of acid waste. This is illustrated by the copper S/X-E/W process used at the Mount Gordon mine in North Queensland, which produces a tank house bleed in the form of a concentrated sulphuric acid stream. The bleed stream is necessary to remove impurities such as iron that decrease the efficiency of the electrowinning process. However, this bleed stream comes at a high financial cost due to large quantities of make up sulphuric acid required as well as the need to neutralise the bleed stream prior to disposal. The present work describes the approach taken to develop a solvent extraction process for the selective recovery of sulphuric acid from copper tank house bleed liquor. The proposed extraction system was investigated using a branched long chain aliphatic tertiary amine tris(2-ethylhexyl)amine (TEHA) as the extractant, Shellsol 2046 as the diluent and octanol as a modifier. Computer simulations were used to determine the optimum operating conditions for the recovery process. It was found that the process was able to selectively recover up to 90 per cent of the sulphuric acid from the copper electrolyte. This is recovered as a pure aqueous acid stream at a concentration of up to 130 g/L that can be recycled back into the tank house circuit or other areas of the process. The raffinate acid concentration was reduced from 180 g/L to as low as 18 g/L, significantly reducing waste disposal and the environmental impact of the copper process. The equilibrium data and simulation results were also compared with an alternative extractant, CYANEXR 923. Finally the efficiency of the TEHA extraction system was investigated on a pilot-scale in a pulsed perforated plate column. This information was used in order to scale the process for an industrial application. The same methodology applied in this case study could be used to provide innovative and cost-effective solutions to waste streams encountered in other hydrometallurgical or chemical processes.

Jan 1, 2000

By M Stewart, J Vann, S Dunham

Geometallurgy is an emerging, cross-disciplinary field that integrates spatial models of rock properties with time-based outcomes of mining and treatment processes. Geometallurgical variables include any rock property that has a positive or negative effect on the business. Some of the more critical geometallurgical variables include recovery, grindability, throughput, power consumption, mineralogy and content of deleterious materials. These variables drive project costs and revenues in a fundamental way and thus geometallurgy has potential to positively impact on the value of strategic and tactical decisions across many mining organisations. Geometallurgical models, like traditional grade-only models are based on samples collected from the mineralised and non-mineralised regions of the deposit. The nature of some non-grade variables, particularly those that are dependent on the ore treatment processes, requires special consideration during sampling and subsequent spatial modelling. Failing to objectively consider the characteristics of variables may seriously compromise the validity of the sample selection, sample treatment, data models and the subsequent decisions. In addition to addressing the vexed question of collecting an æunbiased and representativeÆ sample, the sampling and modelling approach must consider issues of scale, both geostatistical support and also the relationship between bench-scale data and operational-scale mineral processing performance. This paper proposes a framework (the Primary-Response framework) for the classification of geometallurgical variables. This framework is designed to assist with developing sampling approaches and identifying the most appropriate spatial modelling approach. The proposed framework can also help identify the risks associated with designing, sampling and modelling of both types of geometallurgical variables. The Primary-Response framework divides variables into two categories; primary variables and response variables. How a variable is classified in this framework depends on the degree to which the variable reflects either an intrinsic attribute of the rock (æprimaryÆ) or its response to measurement processes (æresponseÆ). Depending on the classification in this framework, appropriate sampling and modelling decisions can be made to minimise the risk associated with the incorrect treatment of the variable. In particular, the authors argue that for response variables, the approach taken to building spatial models may need to be different to conventional linear averaging approaches (for example kriging).

Jan 1, 2009

With the advent of the resources boom in the late-1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large-scale Australasian open pit mining generally.

Jan 1, 2002

By R M. Tosdal

The Manantial Espejo district (Argentina) hosts a low-sulfidation epithermal Ag (-Au) deposit with a proven and probable reserve of 38 Moz Ag and 0.55 Moz Au. The district lies along the southern rim of the Deseado Massif in the Middle to Late Jurassic Chon Aike Province, a large bimodal igneous province dominated by silicic volcanic rocks that were formed during the initial extension leading to the opening of the South Atlantic Ocean. The district stratigraphy consists of 162 to 161 Ma old rhyodacitic to rhyolitic volcaniclastic rocks of the Chon Aike and La Matilde Formations, followed by 160 to 157 Ma old andesites and dacites of the informally called intermediate formation. The main stage of normal faulting post-dates the volcanic activity and coincides with the formation of the precious metal veins that were dated by 40Ar/39Ar on hydrothermal adularia with ages between 152.8 ¦ 0.8 Ma and 156.6 ¦ 0.8 Ma. Economically important hydrothermal veins show characteristic features of a low-sulfidation epithermal deposit with crustiform and colloform banding, bladed calcite replaced by quartz and abundant adularia. In the Maria Vein, the major orebody of the district, six hydrothermal stages are identified, but only stages one and four contributed metal. Lead isotope ratios in hydrothermal sulfides show a close relationship to ratios in feldspars from the district Chon Aike Formation, suggesting a common source for the Pb and possibly the precious metals in both the magmatic and hydrothermal products, or that the Pb in the hydrothermal veins was derived from the volcanic rocks. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Khosrowshahi S

The objectives of grade control remain unchanged but new methods are being developed to attain them. Since the early-1990s, an improvement in the power of mine site computers has made the geostatistical tools of conditional simulation more accessible. Optimisation of the grade control process on mine sites now involves two stages: optimisation of the sampling regime and optimisation of the interpretation of ore and waste boundaries. Optimisation of the sampling regime first requires an understanding of the nature of the mineralisation and in particular the impact of particle size on the sampling precision. This relationship, termed the Fundamental Error of sampling, enables an optimum subsampling protocol to be defined for the sample preparation and assaying. However, the actual sample collection method, whether drilling or trenching, must be correctly selected and the sampling grid should be optimised. The relative costs and benefits of various alternative sampling methods and grids can be determined using the method discussed. The use of the grade control data can also be optimised. In the past ore and waste boundaries were often defined using a linear interpolation algorithm that smoothed the data (such as polygonal, sectional, inverse distance squared or even kriging methods). Frequently the relative impact of ore loss and dilution could not be estimated. Conditional simulation to generate equiprobable alternative maps (realisations) can now be adopted to address these issues. A transfer function is then used to evaluate the similarities and differences between the maps. The Ore Block Optimisation (OBO¬) process is a transfer function that produces a three-dimensional model of the optimal ore block outlines. This provides a clear guide for the mining geologist to refine and mine. The nature of the transfer function and the inputs and outputs are discussed. In the past, reconciliation has been the `acid test' for any grade control system. Any ore blocking method based on conditional simulation can make use of the exhaustive data set to ensure that reconciliation between prediction and production will improve significantly. The OBO¬ method provides a guide to the mining geologist to ensure that the best ore blocks are mined. Misclassification between ore and waste is reduced, ore loss and dilution are minimised (and are measurable) and ore is optimally assigned to stockpiles of various cut-off grades. These advantages significantly enhance mine profitability and control of the mined grade.

Jan 1, 1997

In the mid-1990s, after a long period of antipathy between the company and its detractors, Rio Tinto embarked upon an ambitious cultural change program that sought to transform the fundamental basis of its relationship with global, national and local stakeholders. This has evolved into a broader pursuit of positive cultural change within Rio Tinto as part of the mining industryÆs Sustainable Development initiative. Initially driven from the top down, the communities component of this program comprises an architecture of policies, value statements, social research and verification systems. The commitment to better community relationships is best exemplified in Australia by the scope and scale of the GroupÆs Aboriginal land access agreements, community development programs and the work of the Rio Tinto Aboriginal Foundation. While collectively these form the core elements of an evolving set of internal social competencies, development of second-tier competencies is required to organically embed a culture of sustainable relationships with local and regional communities. Second-tier competencies will include appreciation of social dynamics, social science and diversity at middle management level; rigorous social research that properly informs development options for companies and host communities; career paths and recognition within the mining industry for young professionals both generally and from stakeholder communities; proper community-needs assessments, research into such things as purchasing power and other economics data, and inventories of public goods such as land-carrying capacity and water availability. Without this information it is difficult to gain an appreciation of and to alert people to the consequences of change brought on by a mine. The next decade will see second-tier social competencies promoted within successful mining companies. Measures to achieve this include a range of Human Resource (HR) incentives such as recruitment and career advancement based on broad competencies rather than narrow technical proficiency, humanities training for mining professionals and performance rewards that recognise social competence. A sustainable future for mining in a globally connected social landscape requires selection of people who can listen, relate and act in an open social system. The challenge for the mining industry, its professional organisations and educational institutions is to acknowledge this and develop these new aspects of mining industry professionalism. This cannot be left to individual companies if the industry is to have a sustainable future.

Jan 1, 2002

By A F. Idziak

The aim of the present study was an application of coal optical property measurements for analysis of paleostress field existing in fault zones of the Upper Silesian Coal Basin (USCB) during the coalification of organic matter. Measurements of vitrinite reflectance were carried out on coal samples taken near a hanging stope of the Klodnicki fault. Other samples had been taken in vicinity of the Krzyzowicki fault. The Klodnicki fault is one of the main tectonic discontinuities in the northern part of the USCB. It is postulated that its origin is related to the deep-rooted latitudinal discontinuity in crystalline basement of the basin. The Krzyzowicki fault is located in the western part of the USCB where fold tectonic style dominates. Vitrinite, one of the basic components of hard coal is generally considered as optically anisotropic material. Anisotropy of physical properties is induced mainly by stress, which arranges vitrinite structure. Vitrinite anisotropy can be described by an ellipsoidal model called reflectance indicating surface (RIS) which is a geometrical representation of the optical anisotropy tensor. The investigation of the RIS for vitrinite was carried out on coal samples. The apparent maximum and minimum reflectance values measured for a single vitrinite particle were plotted against corresponding bireflectance to construct the reflectance crossplot. Interpretation of this plot yielded the magnitudes of the RIS three principal axes. The data obtained point to differences in optical anisotropy of coal under the study. The coal samples taken from block tectonic zone near the Klodnicki fault had mean reflectance value of less than 0.80 per cent. Their anisotropy coefficients were about 0.1. Optical properties of coal changed from the biaxial positive in the western segment of the fault to the biaxial negative in its eastern part. It suggests that past tectonic stress was greater in the western part of the zone than in the eastern one. Coal originated from a fold tectonic zone at the vicinity of the Krzyzowicki fault has mean reflectance value much greater than from previous region (ÿ1.20 per cent). Its optical anisotropy coefficient is equal to about 0.07. It suggests that paleostress field was more isotropic. The presented study shows the usefulness of coal reflectance measurements in the analysis of paleostress field existing during coalification process.

Jan 1, 2003

The high-shear colloidal mixer is generally recognised as the most efficient method of mixing cement based grouts. Only recently however has this technology been applied to the production of cemented rockfill (CRF) for use in underground mines in North America. Traditionally, paddle type mixers have been used to produce the cement based slurries required for the preparation of CRF. While considerable success has been achieved with these mixers, tremendous advantages are attained with the colloidal mixer. The combined effect of the highly efficient mixing action and the ability to mix low water/solids ratios, allows for reductions in the cement content for a given strength requirement. Cement can also be replaced by cheaper fillers such as flyash, resulting in further cost savings. Although large-scale dedicated CRF batching plants are typical, there is a growing need for mobile plants capable of operating anywhere underground. The compact size and rapid batching speed of high-shear colloidal mixers has allowed them to be incorporated into skid mounted systems capable of producing and discharging cement based slurries onto rockfill aggregate for the production of CRF. In many cases run-of-mine development waste can be used as CRF aggregate with these slurry plants thereby reducing the cost of waste rock removal. These relatively low cost portable plants have now allowed several mines to economically recover isolated pillars and realise positive returns on their investment.

Jan 1, 1998

By C M. Côte, S Worden, K Svobodova

Mines in Queensland are transitioning to the progressive rehabilitation and closure plan (PRCP) framework. Mine operators are required to select and justify appropriate and viable post-mining land uses (PMLUs) following consideration of the surrounding landscape, community views and the objectives of local and regional planning strategies. The new approach offers opportunities for considering innovative PMLU options and collaborative use of post-closure mine assets, such as infrastructure (power, road/rail, buildings), dams and residual voids. Consideration of regional planning strategies will require a shift in thinking as mine closure is regulated and planned on an individual site basis and selection of PMLUs are commonly considered from this perspective. Planning at regional rather than site-specific scale offers strategic advantages, including the ability to align PMLU selection with the regional context and stakeholder aspirations (which could foster sustainable outcomes); address cumulative environmental and socio-economic impacts; consider options that are only viable at scale (ie across larger geographic areas); establish more extensive and connected ecological habitat corridors; reinstate larger expanses of functional agricultural land; and optimise regional resources (Hattingh, Williams and Corder, 2019). This paper presents the findings from a multidisciplinary project that identified PMLU options within Queensland’s four mining regions: the North-west Minerals Province, North Queensland, Bowen Basin and Clarence-Moreton and Surat Basin (Figure 1). To enable spatial analysis at the appropriate scale and to accommodate geographic diversity, North Queensland was divided into three geographical ‘focus areas’ – Weipa, Charters Towers and Tablelands. Delineation of the areas captured most of the mines within the wider region as well as regional characteristics and features.

Aug 2, 2023

By C Xu, B Li

Multi-sensor fusion visual perception technology significantly enhances visual perception capabilities in complex and harsh environments by combining visual data from different sensors. This technology is especially useful for scenarios where traditional single visible light sensors, such as standard cameras, struggle due to poor lighting, adverse visual conditions, or other visual obstructions. In environments with low light, smoke, or dust, the performance of conventional visible light sensors degrades, limiting their application. By integrating data from various sensors like radar, infrared thermal imaging, and others, multi-sensor fusion technology provides a more comprehensive and complementary visual solution. This fusion not only enhances the robustness of visual systems but also greatly expands their potential applications in fields like visual surveillance. In recent years, deep learning methods have become the mainstream technology for addressing multi-sensor fusion issues, demonstrating significant advantages in adaptive feature selection compared to traditional machine learning methods. However, deep learning-based multi-sensor fusion algorithms still face several challenges. The design of network structures is often redundant, lacking effective screening of useful components within multimodal information. Mainstream fusion algorithms focus excessively on improving display effects without adequately considering the needs of downstream applications and tasks. Existing fusion perception algorithms are generally designed for open visual scenes and lack targeted design for complex visual degradation factors present in tunnel environments of mines. Current deep learning methods for designing multi-sensor fusion networks heavily rely on manual experience to create fusion modules. This reliance increases the complexity of network design and can lead to redundancy. Redundant network modules are difficult to identify in end-to-end learning tasks at this stage, significantly slowing down network inference and potentially interfering with the output of fusion perception. Additionally, training these fusion modules typically requires large amounts of well-annotated multimodal data, further increasing implementation difficulty and cost. For instance, the fusion network design proposed by Li and Wu (2018) focuses on extracting multimodal fusion features, while Zhao et al (2020) introduced a feature decomposition mechanism in the feature fusion and extraction modules. Researchers like Zhang and Ma (2021), Xu et al (2020), and Liu et al (2017) have attempted to improve network structures through dense cascades and the introduction of residual connections. Although these methods have improved the handling of multimodal information to some extent, they still face limitations in distinguishing between useful and redundant information, with redundancy persisting in network designs. Ideally, the design of fusion networks should be more intelligent, guiding network structure design heuristically based on the importance of different modal information for the current task. This would reduce information redundancy and network weights, requiring the development of new algorithms or frameworks capable of automatically identifying and optimising fusion strategies, thereby reducing dependence on manual experience while improving fusion efficiency and network performance. Current deep learning designs for multi-sensor fusion algorithms often overlook the

Sep 1, 2024