Search Documents

By A Kindred

The Bogong Hydropower Development is a 140 MW high head power project currently under construction in Northern Victoria. The project is the final link in the Kiewa hydroelectricity scheme, which was originally constructed in the 1950s. Due to its location in the Alpine National Park, the waterway for the Bogong project must be located entirely underground. A series of shafts and tunnels is being constructed to transfer the water from the headworks at McKay Creek to the new power station located on the shores of Lake Guy in Bogong village. The difference in elevation between the headworks and the power station is greater than 420 m, which poses particular issues for the design and construction of the waterway. The purpose of this paper is to describe the design and construction planning aspects of the tunnelling and shaft excavation and lining works for the waterway. The tunnelling works includes 5.7 km of hard rock tunnel boring machine (TBM) driven tunnel, 1.1 km of drill and blast tunnel and two deep shafts. The tunnels and shafts are lined with a mixture of permanent rock bolts and shotcrete, concrete lining and steel lining. The viability of the Bogong Hydropower Development relies heavily on the ability of the TBM to excavate at high speed through the East Kiewa Grandiorites. Particular attention was given during the construction planning stage to understanding the excavation characteristics of this material, and designing a suitable hard rock TBM that would be capable of meeting the program requirements of the project.

Jan 1, 2008

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

The Banda arc, a U-shaped orogenic belt which separates oceanic crust of the Banda Sea from continental crust underlying the Australian- New Guinea shelf, has been interpreted to mark the convergent boundary between the northward-moving Indian Ocean- Australian plate and the Southeast Asian plate (Hamilton, 1979; von der Borch, 1979; Bowin et al., 1980). East of the island of Sumba (Fig. 1), the oceanic crust of the Indian Ocean has been completely subducted and Australian crust is now thrust under the Banda arc. Controversy has centered over the interpretation of the Timor trough as the surface location of subduction and the significance of the Savu Sea between Timor and Flores as either a forearc basin or the continuation of the Java trench (Karig et al., 1987). Two concentric island ridges, called the inner and outer Banda arcs (Hamilton, 1979), separate Australian continental crust from the oceanic crust of the Banda Sea (von der Borch, 1979) (Fig. 1). The inner arc is a typical volcanic island arc composed of calc-alkalic volcanic rocks of Neogene age, while older (Permian and younger) complexly deformed sedimentary and metamorphic rocks make up the outer arc. Timor is the largest and most extensively studied island of the outer arc and is separated from the inner arc by the Savu Sea. The triangular-shaped Savu Sea appears to be a complex forearc basin divided by a series of buried basement ridges (Karig et al., 1987). The outer, convex side of the Banda arc is followed by a major negative bathymetric feature known ne rho Timor trnnnh

Jan 1, 1987

Based on a principle developed at a South African Mine, the CSIR developed a device with which the alignment of guide rails in mine shafts could be measured. Originally the technique could only be used to obtain guide misalignment values at the bunton sets. At the time this was considered adequate since it was assumed that guide realignment could only be done at the support points anyway. The technology was developed further and now it is possible to obtain æcontinuousÆ guide profiles from the measurements. Software was developed with which a guide realignment schedule can be drafted and the shape of the realigned guides can be predicted. A measuring system based on this technology is being used to conduct guide alignment measurements in shafts. The data is then analysed and a realignment schedule is recommended in consultation with the mine. Such a schedule may be prioritised so that the worst sections in the shaft are dealt with first. The measurement hardware and analysis software are described. Examples are presented that illustrate the principles and highlight measurement errors. A case study illustrates measurements recorded in a newly equipped shaft. A repeat measurement, 18 months later, shows the effect of recommended realignment as well as the change in guide alignment over this period.

Jan 1, 2005

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

By A W. Bewsher, T C. McCu, D B. Mapleson

The Miitel nickel sulfide deposit has been overprinted by a family of late stage structures that have acted as conduits for fluids that have contaminated the orebody with arsenic minerals. This has resulted in highly variable and unpredictable arsenic grades throughout the Miitel orebody. The ore produced from Miitel is processed under a toll-treatment agreement with Western Mining Resources Kambalda Nickel Concentrator. Part of this arrangement includes a financial penalty if monthly average arsenic grades in ore delivered exceed 800 ppm. This constraint has provided an extra challenge to the Miitel mine geologist in addition to daily underground duties. Routine development and stope mapping, close spaced sampling and cross-sectional interpretation were used in building an understanding of the structural controls of arsenic mineralisation and ore repetition at the Miitel nickel mine, and in providing maximum input to mine planning and scheduling. The distribution of structures responsible for arsenic introduction is now well understood from detailed mapping, sampling, and interpretation. By applying these insights to mine scheduling, the operation has successfully managed arsenic levels within the required specifications. Geological mapping has also improved the understanding of the structural complexity of the ore deposit, leading to the addition of ore tonnes and an increased confidence in resource modelling. Regular sampling and tight controls on data quality provided confidence in a strongly skewed arsenic data set. Multiple Indicator Kriging has been used for resource estimation of the arsenic contaminated nickel ore since it allows explicit control of the spatial influence of extreme grades in the positively skewed arsenic sample population. Both the grade control and exploration data sets are used to model the arsenic distribution.

Jan 1, 2003

By D Bradshaw

The recovery of molybdenum at Kennecott Utah Copper (KUC) has become increasingly important as its demand and price have risen dramatically in the last few years. Consequently, the flotation behaviour of the molybdenum bearing mineral, molybdenite, has received a significant amount of attention. The flotation performance of molybdenite generally lags that of the copper sulfide minerals and is much more variable. There are many factors including particle size, liberation, surface slimes and oxidation that contribute to this and also much speculation as to the relative contribution of each of these factors. This paper discusses the morphology of the molybdenite found at KUC, the mineral associations in the different lithogical ores types and the effect that each of these has on flotation performance. Quantitative mineralogical analysis and an assessment of particle shapes are used to explain that flotation behaviour does not necessarily follow expected trends and that some behaviour is counter-intuitive. This unique behaviour can be explained by the morphology and anisotropic nature of molybdenite.

Jan 1, 2008

By Smitham J. B

A selection of Australian washed coal samples was examined to determine the effect of sample hydrophobicity (rank) and particle size on froth stability in the flotation process. The results indicate distinct rank-based variations in froth volume and stability for flotation tests conducted without the use of collector, over a series of particle size distributions.High-rank coals showed a greater tendency to generate stable, high-volume froths than coals of lower rank. Implications for circuit design and operation are outlined.

Jan 1, 1988

Since the introduction of the Neil George Five Point Safety System, to the underground sections of The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines in March, 1969, the Disabling Injury Frequency Rate has been halved and shows signs of contin- uing to fall. The total accident frequency rate has also fallen, although the decrease has not been as significant. Before the introduction of the Neil George Safety System, analyses of the direct causes of accidents showed that approx- imately 25 per cent were caused by "unsafe conditions", while 75 per cent were attribu- table to "unsafe acts". Within twelve months of introducing the system, these percentages had significantly changed to 7 per cent unsafe conditions and 93 per cent unsafe acts. Today, the figures are 3 per cent and 97 per cent respectively, and these figures clearly show that the main emphasis in the current programme must be directed towards making the operating men safety conscious. The effort must be focused on changing the minds of men.

Jan 1, 1975

By J Araya, O Leiva

The mine evaluation process, composed of the designing, planning and valuation of a mine project, is, among other variables, based on an estimated orebody model. However, as the information from the drill holes is limited, it is impossible to know with certainty the mineral content in each block within the estimated block model. Consequently, uncertainty about the value of metal grades, or other geological attributes, arises because of the lack of information at unsampled locations. This is one of the reasons why, in any mine operation, there will always exist a divergence between estimated and real values. Cut-off grade optimisation is the process used to determine the operating mining strategy (long-term production scheduling) that will maximise the total profit value (normally referred as the net present value (NPV)) of a mine operation. This is done by defining a dynamic cut-off grade policy which is constrained by the production capacity of the mining, mill and refining.Real options is a type of contract, written on real assets such as mining, oil and other natural resource industries, that gives you the right but not the obligation to exercise the contract. It is based on operational and managerial flexibility, which allow mine decision makers to react to either good or bad operational and economic events in the future. But, what do geostatistics and cut-off grade optimisation have to do with the application of real options in a mine project evaluation process? The objective of this paper is to answer the previous question by showing how geostatistics combined with cut-off grade optimisation are key tools for corporate/managerial decision makers, which allow them not only to analyse the resource/reserves of their projects, but also to generate operational strategies that can maximise project value by minimising the downside risk due to ore tonnes and grade uncertainties, while achieving operational and physical constraints such as mining and processing capacities. A real copper grade open pit mine project is used as a case study.

Sep 26, 2011

The highland region of Papua-New Guinea is relatively rugged terrain where stream gradients are steep. In areas where porphyry copper deposits outcrop the streams commonly expose primary sulphide mineralization in unoxidized rocks. Stream sediment geochemistry combined with float examination and broad geological mapping proved to be an effective tool for detection of outcropping bodies of mineralization. After discovery, detailed stream sediment sampling, soil sampling and rock chip sampling, together with detailed geological mapping proved adequate to delineate drilling targets. Reconnaissance stream sediment sample density was dictated by geology and access and a density of one sample per 25 Km2, or less, was desirable to ensure a high degree of confidence in the programme. Research indicated that the base metals occur in sulphide form in stream sediment and that the -80 mesh size fraction gave the most reliable results. The evaluation of results from any one area relied on the interpretation of the local geology. Basic histogram methods for determining background and threshold values for metals in stream sediments were

Jan 1, 1973

By E V. Man, O N. Savassi, J-P Franzidis

In flotation, the property that is exploited to effect the separation of a mineral from an ore is referred to as its floatability. Assessment and quantification of ore floatability is of fundamental importance in modelling and simulation of flotation circuits. This paper describes the design, construction and operation of a new laboratory flotation rig that has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to determine the floatability of different ores on a small-sale. The rig is designed for continuous operation. The major features of the rig are highlighted in this paper. An unique characteristic of the rig is a 9.1 L conditioning vessel. This provides a mixing regime close to plug-flow which avoids complications such as different collector coverages for similarly sized particles (which would considerably increase the complexity of ore floatability determination). The main advantages of this rig when compared to conventional batch flotation cells include better control of the chemical environment and the ability to determine froth recovery, entrainment and water recovery with increased accuracy. Preliminary tests undertaken with a high-grade lead/zinc ore from BHP Cannington are presented demonstrating the good level of reproducibility obtainable in operating the equipment.

Jan 1, 2000

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

During the 20th century, the iron ore mining industries of Canada and the United States passed through several periods of transformation. The beginning of the 21st century has seen yet another period of transformation, with the economic failure of a number of steel companies, the acquisition of their facilities by more viable steelmakers, and the consolidation of control within the North American iron ore industry. Changes in Canadian and United States iron ore production and the market control structure involved are analysed. The consolidation of ownership, formation of foreign joint ventures within North America, planned divestitures of upstream activities by steelmakers, and industry changes made to ensure availability of feedstocks will be reviewed. The traditional isolation of the Canadian and United States iron ore operations and their strong linkage to downstream steel production will be discussed in the context of a changing global economy. Management-labour conflicts that have taken place and agreements made during 2000 through 2004 will be discussed in the context of the economic environment leading up to these agreements. Cooperative agreements between competing Canadian and United States companies to resolve client needs in processing and blending will be examined. A joint industry-government project designed to use new technology to produce direct reduced iron nuggets of 96 - 98 per cent iron content using non-coking coals will also be assessed. Changes in iron ore transportation methods, ownership and infrastructure will be reviewed for both rail and inland waterway transport between Canadian and United States companies. A brief analysis of social and environmental issues relating to sustainable development of the Canadian-United States iron ore industry will be included.

Jan 1, 2005

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

By T Muri

The drying operation of materials from particulate solids, through slurries and suspensions, to continuous sheets represents an important part of several processes in the chemical and mineral industries. The increasing demand of high productivity at low cost and minimal environmental impact makes it complex to evaluate and choose the best available drying technology for each industrial application. The drying technologies are mainly characterised on the basis of how the wet product is related to the drying medium, namely: direct and indirect drying. In the direct drying method (convection drying), the product is brought into direct contact with the drying medium, which may be hot gas or air. Large quantities of gas are necessary for transfer of the required energy. A special case of the direct dryer is the fluid bed dryer, in which the product floats on a cushion of air or gas. The process air is supplied to the bed through a perforated distributor plate and flows through the bed of solids at a velocity sufficient to support the weight of particles. Very high heat and mass transfer values are obtained as a result of the intimate contact with the solids and the relative velocities between individual particles and the fluidising gas. In the indirect drying method (conduction or contact drying), the wet product is separated from the drying medium. The drying unit can consist of a rotor forming the indirect contact heating surface mounted in a stationary or rotating shell. The indirect method uses saturated or superheated steam resulting in low energy consumption and minimal environmental impact. In this paper, a review is given of the technologies available on the market based on different drying methods. The advantages and the disadvantages are summarised with respect to issues such as investment and operating cost, maintenance, product capacity, product handling and environmental impact.

Jan 1, 2006

The selection of the ore haulage system is one of the most crucial decisions made in the development of an underground mining project. The haulage system is, once selected, one of the components of a mine that defines its ability to respond to changes in mining inventory and the market conditions for its products. Over the last decade, in Australia at least, this selection process has largely centred on the debate over the merits of shaft and decline truck haulage. Little attention, if any, was given to the application of inclined conveyor haulage as a real alternative to the shaft and truck haulage. This is despite well established precedents for its application in the underground coal industry and some limited applications in underground metalliferous mines. This paper seeks to explore the case for the application of inclined conveyors as a legitimate ore haulage system for underground mines. The case for conveyor haulage is illustrated by an overview of the application of conveyors at some existing operations, and discussion of what conveyors have to offer as a mine haulage system and the issues that are associated with them. Material drawn from the feasibility studies for NewcrestÆs Ridgeway mine and Telfer Deeps Project is presented as case studies that considered selection of inclined conveyor haulage. The purpose of these case studies is to highlight the value of impartially approaching tasks of this type with a robust plan. This plan should be able to respond to issues identified as the task progresses towards the objective of finding the right solution for an ore haulage system.

Jan 1, 2005

By Govett G. J S, Currie D. A, Cohen D. R

Analysis of mechanical size fractions of soils around the Paddington deposit (W.A.) and the Charters Towers Goldfields (Queensland) shows a bimodal gold distribution, with enrichment in the coarsest and finest fractions; this is probably a common feature of soils in arid terrains. To establish the true distribution of Au within the soil fractions, the effect of bulk Au content and percent weight variations in size fractions can be reduced by a normali- zing procedure. The greatest extent of lateral dispersion of Au recorded in the -125 ¦m fraction at Paddington and the -63 ¦m in the Charters Towers area as compared to the coarser fractions, and increas- ed levels of sample representivity in the finer fractions, favours their use in exploration. If orientation studies indicate the preferen- tial use of coarse or intermediate fractions, only wet sieving can quantitatively dis- aggregate the clays and remove finer contamina- ting material. The collection of extremely fine fractions such as the -63 ¦m is also accelerated by wet sieving. The additional costs of wet sieving may be offset by better interpretation of results through increased analytical sample representivity, anomaly contrast and continuity.

Jan 1, 1988