Search Documents

By Lightfoot BW, Bultitude-Paull J

The Sirosmelt top submerged lancing system has many applications in the smelting of base metal and complex materials. It has particular advantages for smaller scale smelting and the treatment of recycle materials in smelters where its low capital and operating costs and its operational flexibility are of immediate benefit. The system can be fueled by oil, gas or coal, as well as by mixtures of fuels. For many applications, the use of coal as a fuel has operating cost advantages over oil and gas, but conventional pulverised coal feeding systems entail very large capital expenditure and this militates against the use of coal. The methods available for improving on conventional technology for coal firing of Sirosmelt systems are discussed and operating experience with alternative systems are outlined. The use of coal as a reductant in the Sirosmelt system is also discussed.

Jan 1, 1987

Tokyo Metropolitan Government designs the stormwater storage plans in underground, as a measure of flood control in completed urban district and improvement of combined sewarage system. This time, introducing those plans, we report about IKEJIRI and SIN-KOMAZAWA STORAGE TRUNK LINEs design and construction. They are located in Meguro river basin of the Morigasaki drainage area. Both storage trunk lines have capacity to store 15O,000m3 of stormwater. They are in use for countermeasure of flood till Meguro river's strengthening (intensity 50 mm/h) is ended. And after the strengthening, they will be in use for improvement of river water quality, through the storage of combined sewage and first runoff, which, otherwise overflows weirs and flows to river in a rainy day. These storage trunk line's full length is about 5700m. Boring diameter 66140 mm (f = 2672m) and 47800 mm (I = 2866m) of these tunnels are constructed by Mechanical Shield tunnelling method. And boring diameter 3600 mm x 4000 mm (R = 180m) is constructed by NATM tunnelling method. We began works in 1983, and have a mind to complete in 1987.

Jan 1, 1987

By K Matsui, R N. Gupta, H Shimada

Roof falls and failures of powered supports were major threats at longwall face. Abnormal geological conditions were caused roof falls and shield damage. Therefore continuous monitoring and analysis of strata behaviour was imperative on real time for forecasting adverse behaviour. Novel PXI instrumentation system was successfully developed for continuous monitoring and analysis of supports pressure, leg closure and gate roads convergence. However, this paper briefly examines the novel gate roads convergence monitoring system with field applications.

Jan 1, 2003

Refractory gold concentrates and their roasted products have been examined by mineralogical and chemical methods, and the distribution of gold in the tailings after leaching has been Investigated.

Jan 1, 1989

Ridgeway Gold Mine (Ridgeway) has a clear mission to maximise its cash flows in order to deliver shareholder value and is developing strategies to achieve this. Business process management using leading measures is core to this approach. Leading measures indicate potential outcomes ahead of time, allowing time to adapt and improve. Ridgeway is making strategy a central organisational agenda, creating a focus to æput first things firstÆ by controlling æleadingÆ activities and mobilising employees to act. Feedback using specific, leading measures gives employees the opportunity to proactively adapt their behaviour in order to deliver internal business outcomes that generate cash flows and shareholder value. This paper will outline RidgewayÆs business approach to track and control processes from resource to revenue, with a focus on delivering cash flows and shareholder value. Ridgeway is implementing a Balanced Scorecard approach (Kaplan and Norton, 1996). A total business focus is taken and leading measures are identified. Specific measures are used to score our success from the perspectives of learning and growth, internal business processes, customer and stakeholders, and finance. These measures and improvement plans are targeted at strategies to maintain our ælicence to operateÆ with our community stakeholders, produce accurate plans and forecasts, improve our operational effectiveness and grow our business.

Jan 1, 2002

By Lawson F

The leaching behaviour of BHAS copper matte in oxygenated acidic sulphate chloride solutions at 85¦C has been studied using samples containing 34% copper, 41% lead and 12% sulphur. Copper sulphide in the matte, essentially Cu2S was found to leach in two distinct stages. Similar to the behaviour of pure chalcocite, copper dissolution in the first stage was affected by the availability of oxygen in solution. The presence of chloride ions in the leachant was essential if there was to be any leaching in the second stage (which usually commenced after about 40% of the copper had been taken into solution). Lead sulphide in the matte was oxidised to lead sulphate and formed a shell around the partially leached matte particles. Electrochemical studies showed that this lead sulphate and/or sulphur produced during leaching can form a passivating layer around the copper sulphide. However, this layer was disrupted when chloride ions were present. A Plackett-Burman analysis was used to determine the species in the recycled leach solution that affect the leaching of copper. Under the experimental conditions used, in the first stage the rate of copper dissolution was influenced by the concentrations of sulphuric acid, Zn(II), Cu(II), Fe(III) and Cd(II). In the second stage, the rate was futher modified by the concentrations of Cl(I) and As(V) ions. In solutions of low acidity and high As(V) concentration, insoluble copper arsenate formed which coated the partially leached matte particles and acted as a barrier to futher reaction.

Jan 1, 1989

The Myally Beds, Surprise Creek Beds and Mount Isa Group form the upper part of the Proterozoic Western succession of rocks in northwest Queensland. The latter two units are partly equivalent, and are important for their base metal content at Mount Isa and elsewhere. The arenaceous Myally Beds lie unconform- ably or disconformably below the Mount Isa Group and Surprise Creek Beds; they contain four mappable units which were deposited on a broad, shallow shelf washed by east-trending currents. Emergence of the Myally shelf initiated a series of parallel, possibly intra- cratonic, troughs to the east and west. In the east, the Surprise Creek Beds were deposited between the emergent shelf and base- ment rocks, and consist of a shelf and trough facies divisible into 7 and 10 units, respectively. Trough sediments are continuous north-south, and show turbidite character- istics; algal dolomite characterizes the shelf facies. To the west in the Mount Isa trough, an orthoquartzite facies, the Warrina Park Quartzite, defines the base of the Mount Isa Group. Hinge zones between the shelf and trough environments are marked by east-west facies changes, and provide a focus for later major north-south faulting. However, some penecon- temporaneous faulting near Mount Isa is best explained as complex post-depositional faulting of a disconformable sequence. Subsidence and deposition in the Mount Isa trough continued for a longer period than in the Surprise Creek trough, allowing accumulation of lead and zinc deposits in the upper half of the sequence. The Surprise Creek Beds appear equivalent to the lower half of the Mount Isa Group, and are probably not prospective for lead and zinc. Turquoise and possible other secondary copper minerals are widespread in the Warrina Park Quartzite and equivalents in the Surprise Creek Beds, and further investigation of these formations seems warranted.

Jan 1, 1974

By Segnit R. E

Two suites of dusts (waste-heat boiler and electrostatic precipitator) collected in 1976 and 1980 from the Kalgoorlie nickel smelter were subjected to chemical and XRD analysis and were examined by SEM and optical microscopy. The spherical to sub-spherical particles contained oxide and glassy phases with small amounts of sulfide. XRD showed that the major phase was a mixed Ni-Fe oxide spinel with some hematite. These phases compared well with those predicted by thermodynamics. The particle size distributions showed that in the 1976 and 1980 suites 20 per cent by weight was respectively coarser than 60 and 115/lm (boiler dusts) and 40 and 30/lm (precipitator dusts). Maximum particle sizes estimated from sedimentation chamber theory were found to be in reasonable agreement with the maximum sizes found in the dusts.

Jan 1, 1984

YOUR Excellency, Fellow Members of the Australasian Institute Of Mining Engineers and Gentlemen:- Nearly a decade has passed, since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 which is a great change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everything in my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1911

A simple and rapid method for delennining gold and silver in carbon samples is described. The method involves dissolution of carbon ash in a strong oxidising medium of aqua regia and hydrofluoric acid. Gold and silver are determined in the resultant solution using atomic absorption speetrometry (AAS). The method is efficient and reproducible. Gold results are comparable to the standard fire assay results, with agreement of results within ± 5 per cent. The co-efficients of variation for gold and silver are 0.37 and 0.39 per cent respectively for six replicate analyses. The analysis of gold and silver in a batch of ten carbon samples can be completed in approximately four hours.

Jan 1, 1992

By Alvarez A. R, Garcia H. l

A fuzzy expert system, DIME, has been developed, under Matlab v 5.1. to assess the coal and gas outburst risk in underground mining. Expert systems and fuzzy logic are powerful tools to manage information represented by linguistic statements,

Jan 1, 1998

By J Ralston, G B. N Kaggwa, L Huynh

Three polymers of varying chemistries and molecular weights have been used to depress talc in a model sulfide ore consisting of talc, pentlandite, and chalcopyrite. Flotation testing revealed a distinct hierarchy of effectiveness of the polymers in the depression of talc (HP Starch > Polymer-H > Dextrin WY) but a different order of effectiveness for depression selectivity (Dextrin WY > Polymer-H > HP Starch). Adsorption isotherm determinations for the gangue and valuable mineral phases indicate that the differences in selectivity are partially due to adsorbed amount variations, with Dextrin WY adsorbing marginally less on the sulfides than Polymer-H. Contact angle measurements on packed particle beds have revealed that the polymers have differing abilities to reduce the contact angle of talc and the sulfide minerals. An explanation of the observed trends is given in terms of the binding mechanisms of the polymers on the talc and the sulfide mineral phases. Order of addition effects between collector and depressant were also investigated using adsorption isotherm determinations for the polymers in the presence of a pre-adsorbed layer of collector and vice versa. Adsorption of the polymers was not affected by the presence of the collector. Similar results were obtained for the adsorption of collector in the presence of pre-adsorbed layers of polymer.

Jan 1, 2005

Rock bolting has become the most important method of ground support at Mount Isa. Various types of rock bolts are used to suit the different applications and requirements. To apply rock bolting techniques satisfactorily, it is necessary to have some knowledge of the nature of the rock, the type of rock failure, any stress redistribution which may occur during the intended life of the rock bolt and the time for which ground support is required. At Mount Isa there are a number of dif- ferent applications of rock bolts for ground support, and some trends in rock bolting techniques.

Jan 1, 1971

THE millng methods employed in the Mount Lyell Mining and Railway Company's mines are, perhaps, less known to the milling world than those of other important districts, due to the geographical remoteness and isolation of the Mount Lyell field,but they present many features which are unusual, and should be of interest to the mining engineer. Typical mining is carried out on an open-stope system, details of which are the result of local experience and evolution, and of which the outstanding feature is that the ground is so worked as to be largely self-supporting by virtue of domical form given to the stope roofs. It is locally termed "rill" stoping,' but differs widely from what is generally understood by that designation, chiefly in that the "rill" or slope is developed in every direction from a central focus, and not merely in directions followllig the strike of a lode or ore-body whose longitudinal dimensions are very much greater than its width. Such terms as "donie stoping" or "arched-back stoping" would be more appropriate and descriptive.The company's active operations' at the present time extend to the Mount Lyell and North Lyell mines, and, though the fundamental principles of stoping methods are the same in each, the dissimilarity of the ore-bodies, both in nature and mode ofoccurrence, necessitates considerable variation as to details to meet the respective conditions. The Mount Lyell pyritic body lends itself to the adoption of the .system in its simplest and almost ideal form, and a description of stoping in this mine willserve best to illustrate it, while later reference to details of practice in the North Lyell mine will indicate how it may be varied to meet more difficult circumstances.

Jan 1, 1915

By Grimstone LR, Leach JHJ

An analytical technique is described to identify areas of structural disturbance to coal and interseam strata in coal measures. It is based on exploration borehole data which records seam intersections and interseam lithologies. Computerised data bases have been developed to allow processing of large quantities of borehole records. The case study discussed is located in a tectonic setting dominated by thrust faulting. It provides a mechanism for the identification of low angle and bedding plane faults. In addition it allows the preparation of plans showing the areal distribution of the thrust sheets in the statigraphic section throughout the mine prospect. The technique requires the identification of normal undisturbed depositional thickness of coal seams and interseams to be determined. This is done for coal by the identification of coal ply distribution over the area. For interseam lithologies it is based on sedimentological modelling of lithology distributions, related back to the original depositional environments. Variations from the expected values are interpreted as structural Deformations.

Jan 1, 1986

The foundation of our industrial welfare lies in the success of our primary industries, and, so far as mining is concerned, it is hoped that for many years it will be a most important primary industry in Western Australia.

Jan 1, 1927

The paper is aimed at mining engineers and other mining practitioners in the metalliferous mining industry who are considering the use of roadheaders and wish to understand the basic geomechanical and operational principles controlling their performance. The paper aims to address metalliferous minersÆ general unfamiliarity with roadheader technology, which is one of the factors which has limited the application of these machines in such mines. The historical development of drag tool mechanical excavation machines is briefly discussed, and factors affecting the application of roadheaders are mentioned. The mechanics of cutting with drag tools is then reviewed as are the effects of these and tool wear on tool performance. The implications of tool performance to roadheader performance are mentioned, the potential benefits of high pressure waterjet assistance are discussed and the relative performances of different tool types and materials are compared. Roadheader performance factors including productivity and utilisation are mentioned, and the state-of-the-art of conventional roadheaders is discussed in the context of machine weight, power and cutting head configuration. The influence of these and rock strength on machine productivity is analysed. Alternative, developing technologies are discussed which may extend the effective use of mechanical excavation into stronger rock masses which are beyond the range of conventional roadheaders. Finally, conclusions on these discussions are presented, along with recommendations for continuing research and development.

Jan 1, 1997

By Binns RA, Murao S

The PACMANUS and Jade deposits are two active hydrothermal fields that are forming massive sulfide deposits at the Pacific rim margin. Both are associated with felsic submarine volcanic rocks and both occur in back-arc settings. However, PACMANUS is associated with almost sediment-free dacites and lies on the crest of a volcanic ridge, whereas Jade occurs in a heavily-sedimented tectonic depression associated with a basement of pumiceous rhyolite. The PACMANUS deposit is richer in Cu and Au, and Jade in Pb. Zinc, Ag, As and Sb contents are similar. Sulfide textures at PACMANUS suggest formation of Cu and Zn sulfides by simultaneous double-diffusion involving inwards-moving seawater mixing with outwards-moving hydrothermal fluid. By contrast, at Jade there is a more complex history of formation where initial growth of barite on the sediment surface, probably associated with microbial activity, formed an impervious cap which trapped higher temperature hydrothermal solutions.

Jan 1, 1995

By L Richards, R L. Brathwaite, C Mazenga

Underground mining of gold-silver bearing quartz lodes was carried out in the great mines at Martha Hill, Waihi over 70 years from 1882 until 1952. Shafts and stopes reached a total depth of 600 m on 16 levels, with workings extending laterally some 1.6 km, and as new reefs were discovered the workings extended beneath parts of the township. Over their long life the mines produced 1217 tonnes of gold-silver bullion from processing 12.2 million tonnes of mined ore. In the early-1980s drilling proved large reserves of gold and silver ore remaining in stock-work zones between the previously mined lodes. This led to a new era of mining at Waihi with the opening of the Martha Hill open pit in 1988. A series of three sink holes have formed above unfilled stopes of the Royal lode. In 1999 a sudden collapse crater 40 m in diameter occurred near an occupied part of Waihi, placing in danger several houses and a busy street. This crater formed close to a similar crater that occurred in 1961. The 1999 collapse resulted in subsurface investigations and risk assessment studies being commissioned by the local Hauraki District Council. However, a further 50 m diameter collapse crater in December 2001 formed in a residential area, swallowing and wrecking an occupied house, fortunately without injuring its five occupants. Two other houses were perched on the crater rim. The 2001 collapse led to an acceleration of the work being carried out by the Institute of Geological and Nuclear Sciences Ltd. (GNS) to identify the extent of the old underground workings at Waihi. For the risk assessment detailed rock mechanics analyses were made to consider the stability of the underground mine stopes, in terms of the stope back, hangingwall, footwall and crown pillar failure mechanisms, as well as void migration. The collapse crater areas were analysed using using several methods, including analysis to simulate the probability of void migration from unfilled stopes to the surface using the @Risk program. The analyses show that in the cases of the actual collapse craters, the voids have a high probability of migrating to the surface, thus providing a method of testing the void migration modelling. Modelling analysis applied to the remaining stopes of the old underground mines show there are further areas where void migration from unfilled stopes has a high, medium and low probability of reaching the surface as a collapse crater. The locations of these probabilistic hazard zones were outlined using the @Risk modelling and deterministically by using the dimensions of the historical collapses applied along the length of the stopes. Consideration of the æincubation periodÆ (the time interval between the cessation of mining and the occurrence of collapse) and comparisons with mine subsidence histories overseas, indicates that further collapses are likely to occur over the next 50 years. Risk assessment estimates made using property values and occupancy levels within the three hazard zones, were compared with Societal and Individual Risk criteria. Results indicate that safety within the high and medium zones may be unacceptable.

Jan 1, 2003

By A G. Greenwood

Research into cemented rock fill at Mount Isa Mines Limited since 1992 is described. The key mechanisms controlling segregation during stope filling with cemented rock fill are described and include the gravity flow mechanism which is described in detail. Examples are provided to demonstrate these mechanisms. Comparisons are made between Mount Isa MinesÆ cemented rock fill and slurry-based cemented rock fills. Recent backfill stability modelling using a three-dimensional finite element program is described.

Jan 1, 1998