Search Documents

The discovery of copper and nickel sulphides in the Riwaka Complex in 1967 led to considerable exploration activity by a number of companies. Various exploration techniques used by these companies are summarised and discussed. Activity of these companies shows that mineralisation is mainly confined to the southern, ultramafic section of the Riwaka Complex where geological mapping recognised sixteen units within, or associated with the Riwaka Complex. Significant pyrrhotite, pentlandite chalcopyrite mineralisation is restricted to biotite feldspar pyroxenites and to clinopyroxenite units. Lesser and more erratically distributed pyrite chalcopyrite pyrrhotite mineralisation occurs in poikilitic pyroxene hornblendites, melanocratic gabbros, and in marginal diorite lenses. It is suggested that a linear belt of layered ultramafic and mafic rocks described in Fiordland by Williams (1974) may be a southern extension of the Riwaka Complex. The Riwaka Complex has been classified as belonging to the Picritic subtype, (Tholeiitic suite), of Naldrett and Cabri, (1976), and as such it is concluded that it exhibits substantial potential for the discovery of economic copper and nickel deposits. It is considered that the complex is a multiphase differentiated intrusion emplaced in a major tensional fracture zone that developed in a relatively stable tectonic environment, namely a succession of middle Paleozoic shallow water shelf sediments. Based on sparse available evidence it is suggested that the Riwaka Complex was intruded in the lower to middle Permian. It is further suggested that the tensional fracturing was initiated by the onset of subduction process which were responsible for the development of the Permian volcanic arcs and ophiolite belt in the north west Nelson area.

Jan 1, 1977

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

A pilot plant has been constructed for the low temperature carboni-zation of Wallarah (N,S,W6) coal at the rate of 300 pounds per hour. The plant was built and tested at Australian Mineral Development Laboratories for Broken Hill Pty, Ltd. Char product was required within the specifi-cation 15.5 `S' 1 per cent volatile matter. The design was based c atz an entrained state carbonizer developed by Parry and U.S. Bureau of Mines co-workers at Denver, U.S.A. The method involved the carbonizatioan of fine coal by entrainment with air in an externally heated reactor.. The heat required for carbonization of tits coal was supplied to the be, both through the reactor walls and also by internal cambustion of products .

Jan 1, 1963

Powercoal Pty Ltd operates eight underground coal mines in New South Wales and produces coal for both domestic power stations and the export market. Approximately 40% of total production is from continuous miners. Over the past five years, place change mining methods have been introduced to improve productivity from continuous miners. This has involved utilising the existing coal clearance system from the continuous miner to the ratio feeder using trailing cable shuttle cars.By late 1996 average productivity at Cooranbong Colliery using this system had plateaued at 800 tonnes per eight hour shift. A number of factors were identified to increase average productivity to 1500 tonnes per eight hour shift. An improved coal clearance system was one of the factors identified.

Jan 1, 1998

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

By Baguley PJ, Napier-Munn TJ

This paper presents preliminary resu]ts from field studies which were conducted to establish, among other things. the influence of medium viscosity on the partitioning behaviour of dense medium cyclones and drums in mineral applications, using frrrosilicon- ba_sed media. The medium vicoosit.y- was measured on-line, and partitioning behaviour was determined using ore sampling and density t r acers . The results demonstrate that viscosity is an important. operating variable, influencing ,eparat.ing density and efficiency under certain conditions. The implication is that metallurgical performance can be optimised by manipulating viscosity, either by appropriate selection of medium' characteristics or by automatic alarming and/or "ontroi using signals from the on- 1. i ne viscometer.

Jan 1, 1987

The Permian coal in the Muja Coal Measures of Collie Basin of Western Australia has a subdued lustre because of the fine laminations of lithotypes, and the dominance of dull and dull banded lithotypes with minor bright, bright banded and fusinous types. The maceral composition of the coal is variable, however the macerals of vitrinite and inertinite groups dominate and the exinite and mineral matter contents are low. The lithotypes have low concentrations of trace elements and the boron concentration is between 10 - 100 ppm recorded only from the dull lithotypes. On the basis of organic petrology, the inter-seam sediments, flora and the very low concentration of boron, the depositional environment postulated for the coal is braided, fluvial and fluvio-lacustrine with marked fluctuations in the water table. The low water table in the environment accounts for fusain and inertodetrinite in the coal.

Jan 1, 1996

By Clark G

The latest addition to the grinding circuit at Bougainville Copper Limited is another 5.5m by 7.3m primary mill (No.13). The mill can operate in a primary or secondary mode. Its distinguishing feature is its capability for speed variation, by means of a cycloconverter-fed synchronous ring motor. The engineering and metallurgical reasons for selecting such a drive system are described together with aspects of the installation and commissioning. Results of investigations into the relationship between mill speed and grinding efficiency are presented. It is concluded that mill speed variation within the range 70 to 80% of critical speed has very little effect on grinding performance. Beyond this range, grinding performance deteriorates. The same conclusions were reached when mill speed was varied at reduced ball charge levels.

Jan 1, 1986

By P Hodkiewicz, K Noormohamed

Gold deposits in the Chirano district in south-west Ghana are hosted in a variety of structural settings along the Chirano shear zone (CSZ), in Paleoproterozoic rocks of the Sefwi-Bibiani belt. Most gold mineralisation occurs in strongly sheared and hydrothermally altered Birimian mafic igneous rocks and tonalite intrusions within the CSZ. A recent program of open pit structural mapping, core logging, and three-dimensional modelling helped to define deposit-scale structural controls on gold mineralisation. These include strain domains, shear zone flexures, shear zone intersections and vein arrays associated with host-rock competency contrasts. Interestingly, the plunge of higher-grade shoots in some deposits appears to be associated with the intersection of the CSZ and broadly folded Tarkwaian sedimentary rocks, which are not significant gold hosts in the Chirano district. This paper presents the results of 3D modelling that were used to define structural controls on mineralisation in several open pits and one underground mine along a 9 km length of the CSZ. LeapfrogÖ software was particularly useful because it highlighted the orientations of structural features that focused hydrothermal fluid flow during alteration and mineralisation. The improved understanding of structural controls provided two main benefits: near-mine exploration drill targets and better definition of structural domains for resource estimation.

Jan 1, 2009

By Felice J. J

The assessment of the face velocity of blasts is important in the analysis and subsequent improvement of blast performance. POWERWAVE RADAR is a new tool which will make the collection of this data easier for blast researchers. The data collection technique ensures that a large amount of face velocity data is collected from a blast, and describes the velocity characteristics of the face at a new level of detail. This results in a greater understanding of the effect of drilling and blasting parameters on blast performance. Several case studies are presented which illustrate the collection technique, the type of data generated and how the data is used.

Jan 1, 1992

By Fleming GJ

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within the Andaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra.

Jan 1, 1995

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

By Flloyd J. M

A continuous oxygen probe,incorporating a SIRO2 solid electrolyte oxygen sensor which measured the oxygen potential of a small volume of gas enclosed above the melt's surface,was constructed and tested. The oxygen potential of iron-silicate slags in equilibrium with solid iron in the temperature range 1250 to 1300¦C were measured continuously for tests of up to 40 hours duration. Results were in agreement with those of previous workers using gas equilibration techniques. Tests on non- iron buffered slags proved unsuccessful due to corrosion of the probe's component in contact with the slag and an alternative material is Required.

Jan 1, 1987

Where tunnel rounds are based on the burn cut, faster advance could often be achieved by increasing blasthole diameter from (the conventional)

Jan 1, 1981

By Grace NC, Lightfoot BW

Small scale trials of the smelting of a copper concentrate in the Sirosmelt submerged lance reactor are described. Pellets of concentrate were dropped into the reactor while injecting air-rich mixtures of oil and air through a lance into a bath of matte overlain by slag. This produced a discardable slag and a matte which was converted in sequential stages in the same reactor to white metal and blister copper. Difficulties were encountered in determining the end points of the converting stages but control techniques were developed to allow successful operations producing blister copper. Deportments of minor constituents of the concentrate to slag, matte,metal and fume for the three stages are reported and possible applications are Discussed.

Jan 1, 1980

By Aziz NI, Bridgwood EW, Singh RN

One of the major impacts of using modern mechanised systems of mining is the production of large amounts of extraneous dirt intermixed with the Run of Mine output. The paper out- lines a proposed system of utilizing liquid tailings from coal mines to replace imported cementitious materials used in ground control and various other safety measures. A geotech- nical and cost assessment of the proposed system are also included. The paper concludes that it is possible to utilize processed tailings to cost effectively replace imported packing material for ground control.

Jan 1, 1986

By Schommarz KH, Dunne RC, Goodall CM

Column cells are widely used today for the recovery of base metals by flotation. Their use for the flotation of iron sulphides has not been as rapid. Australia has pioneered the use of large rougher flotation columns. During the last six years, seven rougher columns have been installed on gold mines treating iron sulphides and the technical viability of this technology has been demonstrated. Laboratory column testwork on a gold bearing iron sulphide ore demonstrated the effects of both physical and chemical parameters. In general the large commercial columns operate over a broad range of conditions depending on the downstream treatment of the flotation concentrate. The addition of wash water to commercial columns is not universally applied and there appears to be a need for a better wash water System.

Jan 1, 1993

By Doxford CI, Perry AJ

Mining Lease 908, situated on Gorge Creek near its confluence with the present Cape River system, has been subjected to intensive recent exploration for alluvial gold.The gold is hosted by a buried palaeochannel, the Gorge Creek Lead and by an overlying remnant meander of the Cape River. The principal, if not sole, sources of gold within the Gorge Creek Lead are the northwest trending Great Australian Reef and Green's Specimen Reef systems which are situated on adjacent high ground. Lower grade gold bearing eluvial ground separates the reefs from the Gorge Creek Lead. The sources for gold within the old Cape River system channel (Canton Lead) are thought to be situated some distance upstream, one source perhaps being the Lolworth Diggings located 30 kilometres to the northwest.Exploration of previously "heavily dug" ground on both leads consisted of detailed geological mapping followed by the collection and treatment of bulk samples from eight costeans. The wash samples varied in size from 120 to 396 cubic metres. Treatment was undertaken through a commercial sized conventional wet screen and jig plant.

Jan 1, 1986

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992