Search Documents

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

The Beaconsfield Gold Mine within the township of Beaconsfield in northern Tasmania has been established in recent years to exploit a known resource in the Tasmania Reef which was mined to a depth of 450 m below surface between 1877 and 1914 yielding 850 000 ounces of gold. Activity at Beaconsfield over the past 30 years has involved drilling to assess the resource and rehabilitation of the top 100 m of the Hart Shaft that had collapsed since the original closure. More recently the mine has been dewatered to the 375 m Level and work is well advanced establishing infrastructure aimed at recommencing production during 1998 - 99. This paper reviews geotechnical studies undertaken to-date and provides a brief overview of some practical methods of analysing ground conditions. It pursues simple observation and analysis as a tool for assessing mine design and ground support options without recourse to extensive monitoring and measurement and avoids the use of elaborate models before the basics are understood.

Jan 1, 1997

Ferromanganese metasediments in the immediate vicinity of the Mid-Proterozoic Broken Hill Pb-Zn-Ag lodes, have undergone high grade (upper amphibolite facies) metamorphism,to form Mn-pyroxenoid (rhodonite,pyroxmangite) and garnet-rich lithologies. Such lithologies bear compositional (bulk rock,rare earth element)and morphological similarities to recent and ancient ferromanganese hydrothermal sediments of the Pacific.The non-metasomatic,stratiform garnetites are predominantly composed of magnesia-rich, calcium-poor almandine spessartine and quartz, which possess a bulk chemistry comparable to alumina-rich ferrommanganese oxide deposits of the Pacific. Such sediments are attributed to a mixed protolith comprised of clay and ferro-manganese oxides (mainly amorphous goethite with lesser todorockite-birnessite). Manganiferous pyroxenoid rocks are probably derived from alumina-poor ferromanganese cherts,similar to Japanese tetsusekiei.Rare earth element compositions ofBroken Hill garnetites are very similar to those of recent ferromanganese seafloor accumulations, suggestive of some genetic link.

Jan 1, 1990

The techniques originally developed to process digital images of Mars, later gained widespread acceptance when applied to Landsat data: they are now making a significant impact in fields of geology outside remote sensing. The three ingredients of success are seen to be firstly, the perceptual attributes of image displays and the use of colour; secondly, the absolute ability to register data from a variety of sources; and thirdly, the speed of specialist "interactive" digital image display systems. The future lies in further exploiting these attributes through a Geographic Information Systems (GIS) approach to data handling, integration and display.

Jan 1, 1986

By Corner NG

A sea bed sampling programme by CRA Exploration Pty. Limited over an area of 12000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 100 m and contained a high grade core of 33 km2 which averaged 283 mghn3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10-40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 It turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

By Valery W, Morrell S, Loughlin P, O&apos

Traditionally, blasts in mining operations are designed to prepare the in situ rock mass for excavation and transport without much consideration being given to the downstream comminution processes. Blasting is in fact the first step in a chain

Jan 1, 1998

By Thomas MJ

The Cannington silver-lead-zinc deposit is located at latitude 21¦ 52' 9" South, longitude 140¦ 55' 10"" East, on the south-eastern margin of the Proterozoic Mount Isa Block (Figure 1), 135 kilometres south-east of Cloncurry. Access is via a graded shire road for 80 kilometres south from the small pastoral community of McKinlay.REGIONALThe deposit is hosted by the Proterozoic Soldiers Cap Group within the Mount Isa Block Eastern Succession. South of the Cloncurry Beardsmore et al (1988) have grouped part of the Eastern Succession stratigraphy intothe Fullarton River and Soldiers Cap groups (1760-1740 million years) which together make up the Maronan Super Group. This is an apparently conformable sequence 10 kilometres thick and consists of metamorphosed sediments and volcanics with intrusive amphibolite bodies.The Maronan Super Group has experienced a complex history of deformation with up to six events having been recognized. The stratigraphy trends broadly north-south and is predominantly characterized by tight, upright isoclinal fold structures.

Jan 1, 1993

The 250 metric tonnes of gold and 360 000 metric tonnes of copper recovered from the Mt Morgan Mine in Central Queensland justify its fame. The mine ceased operation before the advent of three-dimensional computer graphical modelling of orebodies became common practice in mine planning. The Mount Morgan Mine records however remain and are the database for this study. The Mount Morgan project takes ore deposit modelling one step further by examining the relationship between grade distribution within the orebody and key geological features, as a tool for exploration and development.The Mount Morgan gold and copper mineralisation is shown to be strongly lognormally distributed. The deposit has been split into three areas, using geological boundaries, each with different geostatistical characteristics. Important features include: the spatial relationship of near-vertical, high grade shoots with a ring dyke thought to be related to the North Dyke; separation of the high grade eastern stopes from the others along the Andesite Dyke; and lack of concentrated mineralisation along the Slide Fault.Recognition of these features is useful to those currently exploring the Mount Morgan district for similar style deposits, by stressing the importance, or lack thereof, of the geological features.

Jan 1, 1993

It is difficult with inadvertent explosions to establish fundamental data, especially of original dust, of pressure, temperature etc. and of ventilation oscillations, as exposed personnel rarely survive. Retrospective data from explosions must be derived from damage, from fatalities, from ventilation analyses, from analyses of dusts and other indications of temp- erature and duration of temperature. The five disastrous explosions selected for analysis provide examples of what data can be established as to the cause and extent of explosions. Such information is required for legal etc., inquiries subsequent to explosions, but most importantly to give the best guidance for avoidance of possibility of further Disasters.

Jan 1, 1981

Discovered in 1896, the Sons of Gwalia orebody is located in a ductile mylonite zone within a sequence of Archaean pillow metabasalts and minor metasediments of greenschist facies which are variably sheared.The ore zone has good continuity, being 110 m wide and 500 m long, dipping 45 degrees east and plunging 70 degrees to the south to a depth of 1500 m downplunge. A strongly-developed foliation is present together with a prominent lineation paralleling the plunge. The mylonite zone consists of unmineralised chlorite schist and a 'U' shaped mineralised zone of chlorite-sericite schist with varying amounts of quartz-carbonate as veins parallel to foliation, boudins, and locally as massive quartz-carbonate. Pyrite is the dominant sulphide present.Grade control utilises RC holes on a 10 m x 10 m pattern, with infill blast rig holes 5 m deep where necessary.Some visual control of ore boundaries is present and, combined with good ore continuity and a knowledge of the structure of the orebody, enables cost-effective grade control to be achieved. To-date, over three million ounces of gold have been produced from the orebody.

Jan 1, 1993

The nickel ores mined in New Caledonia for one century are mainly silicate ores. These ores are nickel enriched saprolites, formed by partial weathering of peridotites (predominantly harzburgites and some dunites), serpentinised to varying degrees. Saprolites constitute the lower horizon of lateritic soils, sometimes up to 100 metres thick, developed on peneplains now greatly modified by erosion. Saprolites are generally overlain by laterites, a more weathered horizon, where the main components are iron oxy-hydroxides with a low nickel grade. The structure of saprolites depends essentially on the serpentine content of peridotites and, on the other hand, serpentine minerals may have a high nickel content and, so, represent important nickel bearing minerals in silicate ores. Two types of serpentines can be found in nickel ores from New Caledonia: ò primary serpentines, formed by hydration of olivine at temperatures below 400¦C, during overthrusting of peridotites in late-Eocene (Paris, Andreieff and Coudray, 1979), are generally very abundant; ò secondary nickeliferous serpentines, associated with other sheet silicates in garnierites, are now relatively scarce but garnierites were selectively mined one century ago, because of their high nickel grade.

Jan 1, 1996

By Fitzgerald DE, Taverner MG

The principles, fields of application and equipment design concepts of several new approaches to continuous vacuum treatments of molten metals and alloys are discussed. Partic- ular attention is paid to the results of pilot plant tests evaluating a launder-in-tube method of 1. continuous production of refined zinc from a zinc-bearing lead produced in the lead splash condenser of the Imperial Smelting Furnace (ISF), and 2. continuous refining of crude cadmium. The former trials were not sufficiently encouraging to justify consideration of the process for commercial development. The applic- ation to cadmium upgrading gave very promising results; metal of 99.99 per cent purity was produced continuously at pilot scale (120 lb per hour) from crude metal containing 5.0 per cent Pb.

Jan 1, 1972

By Clarici E, Marsden J. R, Calderbank P. A

Evaluation of previous studies of multi-layer perceptron type artificial neural networks in the modelling of the deformability behaviour of rock have suggested that a deviation from the standard method of laboratory testing of rock under triaxial loading at constant confining stresses and constant axial strain rates may be inappropriate when the data produced are used to train an artificial neural network. In this paper, preliminary results of adopting such a strategy are reported. Of specific concern is the establishment of a suitable schedule for the stress path during testing. Furthermore, the training element of back propagation optimisation was directed towards prediction of new stresses given old stresses and old strain increments. Adoption of this method of supervisation in artificial neural network training facilitates the integration of the trained neural network within existing numerical methods used in rock mechanics. The target code was a finite difference Lagrangian formulation for the analysis of continua. Sandstone rock taken from a quarry in the UK was used in the study which showed that the method has great potential.

Jan 1, 1995

By Clarke DS, Sporli KB

Structure is an important control in the localisation of gold mineralisation in epithermal systems. There has been, however, only limited investigation of the structural elements involved; such a study is currently directed at the gold deposits of the Coromandel Volcanic Zone (CVZ). Here, mineralised veining and brecciation ranges up to tens of metres in thickness. Dips of veins are mostly steep, but not vertical, and there is a significant number of low angle veins.The structural control of epithermal deposits may be considered on four scales. At the mega-tectonic scale, pre-volcanism fault patterns mostly relate to separation of the New Zealand micro-continent from Gondwana. The major structural controls on mineralisation at this scale, however, are associated with the volcanic arc processes responsible for the CVZ. Post-mineralisation faulting are linked to the Hauraki Rift and the Colville Ridge-Havre Trough system. Regional scale faults controlling the distribution of gold deposits are the product of these tectonic events; much of the faulting may relate to rifting and calderas, but further work is required to demonstrate this. Detailed study is also needed on vein systems at the prospect scale to validate models of brittle deformation responsible for such systems. Evidence that a variety of structural mechanisms dominated in different deposits is found at the vein scale, with Coromandel gold deposits being classified according to their different styles of vein-fill texture.

Jan 1, 1990

By Gyasi-Agyei Y

In recent years rapid advances have been made in the technology used for hydrology and erosion modelling of rural catchments. These advances have been driven by the growing availability of digital terrain maps that can be used to automatically define catchment properties that previously had to be manually extracted from contour maps. In addition, these models have, in principle at least, more powerful predictive capability. The author is involved in a number of projects to migrate and further develop these models for application to mine rehabilitation assessment. Current technologies for hydrology and erosion assessment (eg CREAMS, ANSWERS) are reviewed, underlying principles highlighted and deficiencies in the context of mine rehabilitation design assessment addressed. The advantages and disadvantages of the new digital terrain map tools (eg WEPP, SIBERIA) are discussed. Current work integrating these new models with existing rehabilitation design tools (eg ACIRL's ARGUS computer package) highlights the advantages of an integrated approach using digital terrain maps; cheaper, faster, lower impact and more flexible rehabilitation design. The use of novel visualisation tools to aid the design process is discussed. The paper is illustrated by applications to mine sites in Queensland and the Northern Territory.

Jan 1, 1995

By J Finlay, P Betts, D Milton, H Williams

The aim of this paper is to present an innovative method to help delineate potential target volumes for haematite-goethite mineralisation as opposed to more magnetic ores. This is achieved through interpretation and modelling (2.5D and 3D inversions) of ground magnetics and gravity surveys over the Koolanooka South prospect in Western Australia. The targets are assumed to be dense and weakly magnetic and hosted within banded iron formation (BIF) horizons. Geophysical interpretation (2D map) was performed using a variety of processed magnetic and gravity images (Betts et al, 2007) to determine the distribution of lithologies, to understand the structural architecture and to map out any anomalous areas of excess density (possibly indicating goethite alteration). The created geological map is used to build geological cross-sections (geometrically consistent) that were modelled (in 2.5 D) against both potential field datasets. The crosssections are consequently used as the framework to build a 3D geological model. The model defines 3D volumes of rocks including several BIF horizons. The distribution of densities and magnetic susceptibilities of the BIFs is inverted within the GOCAD«-VPmg environment to reduce the misfit between the response of the model and the observed gravity and magnetics. By combining the results of both petrophysical property distribution it is possible to map out (using classical GIS type queries in 3D) volumes of higher density and lower magnetic susceptibility.

Jan 1, 2009

The .subject of this paper is to briefly outline various methods of stockpiling and reclaiming, and the use of different types of bucketwheel re- claimers and stackers in these operations. The paper examines briefly the different types of bucketwheel equipment, their operations and relates them to different stockpile layouts, giving examples of their application in Australia.

Jan 1, 1973

High interest to basic-ultrabasic rocks is ex-plained by their specific, sutural, geotectonic po-sition and by deep level of generation of ultraba-sic magmas. These two factors allow us to treat this group of rocks as valuable source of informa-tion about the lower crust and upper mantle of the Earth. Basic-ultrabasic xenolith series is another source of information about the interior of the Earth. Detailed studies of the xenolith series give valuable material to geologists as to how endogenic deposits are fed and what is their source.Besides, the interest is explained by attempts to understand the relationship between basic-ultra-basic complexes and deposits of metalliferous and non-metalliferous mineral material.Absence of genetic boundaries in manifestation of metalliferous and non-metalliferous minerals, their temporal and spatial relationship allow us to treat the minerogenesis of ultrabasic complexes as a result of one ore-forming process manifested in Koryak-Kamchatsky, Sakhalin-Japanese, Ryukyu-Korean and Taiwan-Philippines island arc systems which re-present, in the opinion of the authors, one eastern Asian chain of the Pacific ore belt (Radkevich, 11)87).

Jan 1, 1990

By Draper J. J, Lang S. C

Regional geological mapping and facies analysis of the Late Devonian to Early Carboniferous Keelbottom Group of the Burdekin Basin have resulted in a depositional model representing six siliciclastic-carbonate facies. The six facies represent alluvial fan, braidplain delta, siliciclastic shoreline, siliciclastic shallow marine, restricted siliciclastic/carbonate shelf, and carbonate shoal depositional environments. These facies are identified in the Star beds which are equated with and included in the Keelbottom Group in this paper. Facies are repeated throughout the Group, as a result of two transgressive-regressive cycles.The first transgression recognised in the Keelbottom Group began in the mid-Famennian, and followed deposition of the Late Devonian Dotswood Group. It was marked by the deposition of Siliciclastic Shoreline facies in the basal Myrtlevale Formation, which was succeeded by Siliciclastic Shallow Marine facies at the peak of the transgression. The return of Siliciclastic Shoreline facies in the upper part of the Myrtlevale Formation marked the onset of the first regression, which resulted in the progradation of Braidplain Delta facies from the northwest of the basin. During the peak of this regression, deposition in the western part of the basin was dominated by Alluvial Fan facies.

Jan 1, 1990