Search Documents

Winzes are usually sunk 9 ft. 6 in. long by 6 ft. 0 in. wide and are divided into two compartments, 4 ft. 0 in. by 5 ft. 0 in. inside the timbers. The general practice is to sink the winze to a depth of from 9 to 12 ft., put in bearers and three or four rings of timber, and then erect a sinking headframe before continuing sinking operations.GENERALThe main feature governing the design of the headframe was that all parts could be transported on timber trolleys in No. 2 Shaft. Except for some minor details the structural members consist of steam pipe. Joints are sections of steam pipe welded to one member and into which the other member fits and is held in place by a 1-in. bolt. The headframe consists essentially of two bedpieces to carry the winch and to form a seat for the four legs. The legs support the sheave bearers, the tipping door and the brace.Except during tipping operations the door is in a nearly vertical position. For tipping it is lowered to an inclined position and a hook suspended from one of the bracing members of the headframe is attached to a "D" welded to the bottom of the kibble. This causes the kibble to tip when it is lowered on to the tipping door. The capacity of the kibble is 4 cubic feet.THE HEADFRAMEThe dimensions of the headframe are:Height to top of sheave .. .. 14 ft. 10 in.Distance centre to centre of legs 4 ft. 4 in.Length of bedpieces .. .. .. .. 8 ft. 9 in.The weight is approximately 2,000 lb., the tipping door and bedpieces being the heaviest members. They weigh 240 lb. and 170 lb. respectively.One compartment of the winze is decked over, and the bedpieces, which are 8 ft. 9 in. lengths of 6 in. pipe with three short lengths of plate welded to the underside, are placed over the sinking compartment, either transversely or parallel to the winze. Three 3 inch pipes act as spreaders between them.Welded to the top of each bedpiece is a 6-in. by iHn. plate 3 ft. 0 in. long with four 4-in. by 1.5-in. slots cut longitudinally at 10 in. centres. Two 10 in. by 4-in. timbers are bolted to these plates, the distance between them being adjusted to suit the holes in the winch bedplate, which is bolted to the 10-in. by 4-in. timbers.Two short lengths of 3 in. pipe are welded to each bedpiece at 4 ft. 4 in. centres. These form the seats for the legs of the headframe, which are...

Jan 1, 1941

In general, the metallurgical industry has so far been slower than the chemical industry to adopt ion exchange materials for industrial processes. The atomic energy industry presents a marked exception to this general situation, and the literature shows a rapidly increasing use of ion exchange techniques for the recovery of atomic energy metals on scales ranging from the ultra micro up to that of the largest mining operations. In many cases, the processes used would be equally applicable to more common metals and it is hoped that this review will be of interest to metallurgists outside the specialised atomic energy field. The review is intended to describe developments of ion exchange processes made during the last three years. Earlier studies have been summarised by Kunin and Preuss (1956) and Roland (1957). In order to restrict the number of references discussed, purely analytical procedures have been omitted and only those processes which have been conducted on a reasonably large scale or which, from their nature, areclearly capable of being upscaled, have been considered. The paper is divided into five main sections concerning respectively:Water treatment and effluent disposal.Metal recovery and purification.New ion exchange materials.New ion exchange equipment.Membrane cells.WATER TREATMENT AND EFFLUENT DISPOSALA high proportion of atomic reactors, and particularly those of American design, are cooled by water which is...

Jan 1, 1961

By Parker A. J, Giles D. E

Solutions of copper(II) sulphate in acidified aqueous acetonitrile leach copper from copper-lead matte derived from the drossing of lead with sulphur to produce solutions of copper(I) sulphate. The reactivity of the matte constituents towards copper(II) sulphate is Cu2S> PbS > CuS > > Pb. According to the leach conditions, part or ,all of the copper may be leached 'leaving a residue of CuS/PbS, or S/CuS/PbS04, or S/PbS04, to be recycled to the lead smelter. Complete extraction of the copper requires leaching with oxygen which occurs under mild conditions in the presence of acetonitrile and sulphuric acid in water. Copper is selectively recovered as a pure product by electrochemical or thermal disproportionation of copper(I) sulphate solutions. A notional process is proposed.

Jan 1, 1979

By Wesley, Worner H

During the meeting of the Institute last year at Port Pirie, the opportunity was taken to sample the lead bullion coming from the blast furnace and various stages during the refining process. Also, in the desilverising section, the upper zinc rich phase was sampled as the silver content built up and in the cupellation operation a series of samples was taken as the silver content of the bullion increased. In these two cases, the samples were taken under the supervision of a member of the staff of the Broken Hill AssociatedSmelters.In the following account of the microstructure of the samples taken, only the main phases present have received attention. In this connection deduction from phase diagrams of binary alloys has been used in conjunction with the assays carried out on duplicate samples taken at the same time as those for micro examination.

Jan 1, 1938

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic & Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

A Sun SPARCstation based computer network is utilised to store and process mining data at the Macraes Gold Mine. Techbase and Medsystem software running on the SunOS unix platform is used to generate all data plans, sections and other design data required on a daily basis to run the mining operation. The Macraes site is regarded as a fully integrated site where all geological, grade control, exploration, orebody modelling, resource estimation, pit optimisation and mine design is undertaken on site by MacraesÆ professional staff. The methodologies employed are regarded as æstate-of-the-artÆ where computerisation allows the rapid and efficient evaluation of large quantities of mining data by a handful of professional personnel. Ore reserves are estimated using an indicator kriging method and roving cone pit optimisation, a complex process that would not have been achievable in pre-computing days.

Jan 1, 1992

Since the end of World War n, many important developments have taken place in the investigation of the phenomenon of brittle fracture in mild steel. Fractures in certain classes of welded ships, in welded bridges, penstocks, etc., focussed a great deal of attention on the interrelationships of design factors, service conditions, and steel quality on the generation of catastrophic failures.Much publicity has been given these major failures, and there is perhaps a tendency to forget that mild steel, under certain conditions, as well known to behave in a brittle fashion in a wide range of everyday engineering applications.For instance, many who are connected with the haulage and lifting of heavy loads will be familiar with the bright "crystalline" fractures of crane hooks and chains which sometimes follow sudden jarring; those concerned with the heavy pressing and shaping of steel plate will not be unaware that at times sudden brittle splits or tears will develop for no obvious reason in, say, rolled pipes or in dishings.In fact it will be evident upon reflection that in many cases the conditions which mild steel has to withstand during processing into an engineering part or structure are more severe than those it wili be called upon to endure during service. In this sense brittle fractu;res in mild steel are much more frequent than are commonly supposed.Two modes of fracture are now generally recognised to occur in metals, namely, shear and cleavage. The latter manifests itself by the so-called "crystalline" fracture (here...

Jan 1, 1954

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

By C G. Ryan, T P. Mernagh, S R. Hunns, R A. Both, R R. Large, J B. Gemmell

 The Hellyer and Mt. Chalmers deposits are mound-style volcanic-hosted massive sulphide (VHMS) deposits in Australia. Textural, petrographic and microthennometric investigations of fluid inclusions in the Hellyer stringer system indicate that Type I, primary, liquid-vapour inclusions are 10 - 15 J.UIl in size, and yield homogenisation temperatures of 170 - 220¦C in early 2A veins, 165 - 322¦C in main-stage 2B veins and 190 - 256¦C in late-stage 2C veins. These data suggest a waxing and waning thermal history. However, the average salinity remained between 8 - 11 NaCl equiv. wt % in all Stage 2 veins. At Mt Chalmers, Type I inclusions up to 20 urn are found in quartz from the mineralised zone, and these inclusions yielded homogenisation temperatures of 160 - 268¦C and salinities of 5 - 8 NaCl equiv. wt %. Laser Raman spectroscopic (LRS) analysis indicates the presence of CO2 (<1 mole %) in the Hellyer and Mt. Chalmers VHMS systems. Semi-quantitative SEM/WDS microprobe analyses of fluid inclusion decrepitates indicate that the Hellyer and Mt Chalmers ore fluids were enriched in potassium and calcium but depleted in magnesium relative to seawater. PIXE microanalysis of fluid inclusions in quartz also indicates a significant base metal concentration in these fluids. Cation composition and higher salinities relative to seawater suggest that recycled seawater alone cannot be the sole source of the ore fluids. High base metal content and the presence of CO2 in the fluid inclusions imply that magmatic input of ore metals during seawater leaching of the footwall volcanic pile is a distinct possibility.

Jan 1, 1995

IT has often been stated in the past that the materials known as inert fillers were merely adulterants nsed in the manufacture of paint, and that their purpose was to cheapen paints made from more expensive pigments, such as zinc oxide or white lead. In recent years, however, practical tests in various parts of the world have proved that many of the inert fillers, when used with wisdom, possess very definite and advantageous properties.Another oft-repeated statement which had a far-reaching effect in the past, and which is not without influence to-day, is that the very best paint must always be made from a pure pigment, without admixture with either a fellow pigment or an inert filler. Both or either of these statements may be true in a few isolated instances, but for the vast majority of ordinary painting conditions there is an abundance of experimental evidence to prove that neither is true.With the desire to further investigate these points and po 'determine the best combination of pigments and fillers for use as an outside white paint on plant buildings, a number of panels were prepared in the laboratory of this company.

Jan 1, 1924

The construction of the pipeline was completed in June 1956 and the line placed into operation in December 1956, ie. it has now been in continuous operation for approximately three years under an operating pressure of up to 350 lb. p.s.i.In reviewing the operating experiences of the line we must consider three major factors, which are:(a) The effectiveness to date of the protective methods for prevention of corrosion of the pipeline, ie. the preservation of the asset.(b) The maintenance of the line in regard to interference as to its stability which could be occasioned by erosion of the line, land-slides, accidental interference by the public, or construction authorities, etc.(c) The operating techniques employed.PROTECTIVE METHODS OF THE PIPELINESo to permit a clearer appreciation of the effectiveness of the protection of the! steel pipe against corrosion, I will briefly describe the methods used in the construction of the line.The line, which is 18 in. O.D. by %6 in. thickness steel pipe, is located approximately It miles south of the main Melbourne/Gippsland electrified railway.The steel from which the pipe was manufactured conforms to ASA.A33-1937 with the following modifications.Minimum elongation on a 2 in. test specimen...

Jan 1, 1960

I would take this, opportunity of thanking you for the high honour you have conferred on me in electing me to the responsible position of President. You may rest assured I will use my best endeavours to promote the interests of the Institute in every way that lies in my power. In reviewing the work of the past year, it is a matter for congratulation to find the Institute in a position at once so healthy and robust, and that notwithstanding the acute depression which has prevailed in the mining industry.Owing to deaths or departures from the colony, the names of six members have disappeared from the roll of membership, but you will be pleaed to learn that several new members have been elected, the register now, showing 56 Members, 25Associates and 2 Students. A complete record of the papers read and the discussions that took place will be found embodied in the splendid volume of Transactions which has just been issued, and which I am sure will be welcomed by mining engineers in all parts of the world.

Jan 1, 1901

By Alvin J. F

Tin in ores containing 0·025 to 1·5 per cent tin can be determined polarographically by the reduction of the chlorostannite ion at the dropping mercury electrode in 2M hydrochloric acid solution containing 15 per cent ammonium chloride. The tin is separated from interfering elements by distillation as the tetrabromide and collected from the distillate by co-precipitation with aluminium hydroxide. The method can detect 0·01 per cent tin in ore.INTRODUCTIONAn iodimetric method, suitable for routine analysis of titrating tin in concentrations down to 1 per cent, has been available for some years (Low, Weinig, and Schoder, 1939).As concentrations fall below 1 per cent tin, there is increasing difficulty in obtaining a distinct end point due to large amounts of iron and silica normally present after fusion of the ore. Since concentrations of tin down to 0·02 per cent are significant in ore dressing products it was necessary to examine methods to determine such low concentrations, and to adapt these to tin ores containing a wide variety of other minerals.EXPERIMENTALDigestion and separationCassiterite, the principal tin mineral, is refractory but readily attacked by a sodium peroxide flux to yield soluble sodium stannate. In a recognized procedure, a sample of ore is mixed with up to 15 g of sodium peroxide in an iron crucible and swirled over the full heat of a Meker burner for 7 min. The fusion is leached with water and acidified.This solution then contains tin, silica, and other soluble...

Jan 1, 1962

During the latter part of 1937 consideration was given to the construction of a; local smelting plant for producing blister copper. Previously copper concentrates had been shipped to the United States of America. The proposition had the advantages of a saving in cost of realization, quicker financial return and reduced dependence on overseas shipping.The smelter was designed by the existing staff, who had difficulty in obtaining data on small plants, particularly on the reverberatory furnace. Construction was started in March, 1938, and the reverberatory was blown in on January 16th, 1939. One roaster had been operating for several weeks prior to this date.While results and operating technique on this new departure in small-scale smelting are barely beyond the experimental stage, it is felt that the experience gained to this time should be recorded to help fill the obvious gap in published information covering plants of this type.At present there are three copper smelters operating in Australia; the other two plants are equipped with blast furnaces.LOCATIONThe new smelter is situated in a position convenient to the concentrator and to the power plant. The site is traversed on two sides by a brick flue, from an old smelter plant, which connects with a 250-ft. stack. This stack and portion of the old flue are used in connection with the...

Jan 1, 1939

Kinetic Behaviour of Solid/Solid Separation of Ultrafine Particles in Aqueous Suspension

Sep 13, 2010

By Z S Chang, T F. Zhou, G X. Zhong

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Yaojialing zinc-gold polymetallic deposit is a newly discovered, large skarn deposit in the Middle-Lower Yangtze metallogenic belt, East China. It is located in the transitional zone between the Tongling uplift block and the Fanchang faulted basin. It is mainly hosted in the contact zone between early Cretaceous granodiorite porphyry and Carboniferous-Triassic limestone, or occurs in limestone xenoliths within the intrusion. Skarn and stratabound massive sulfide orebodies are the primary ore styles. Sulfide ?34SV-CDT values indicate a magmatic sulfur source, in common with most deposits in the Tongling block. Calcite d13CV-PDB and d18OV-SMOW ratios reveal that marine carbonates were the major source of carbon in late-stage hydrothermal fluids. The calcite probably formed during interaction between magmatic fluids and carbonate wall rock.CITATION:Zhong, G X, Zhou, T F and Chang, Z S, 2015. Geology, chronology and isotope geochemistry of the Yaojialing zinc-gold deposit, Tongling ore district, Anhui Province, China, in Proceedings PACRIM 2015 Congress, pp 457–462 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

By Pupazzoni P. D, Meissner D. C

Incorporating an iron ore pelletising plant, a MIDREX'"' Direct Reduction Plant, and a mini mill, the conversion of iron ore fines to high- quality steel slabs in Western Australia is among the lowest cost routes in the world. The cost and availability of iron ore and natural gas, government support, and proximity to the growing Southeast Asian market all contribute to the competitive position of the area. Owing to the lead-time required, this is an ideal time to develop a new project to supply semi-finished steel to Asia for rolling to a finished product. A project contracted now will start up in about three years, when the market should have recovered.

Jan 1, 1999

By W E. Vance, B H. Ashton

The emission of seam gases into underground workings in coal mines is acknowledged as a major hazard, particularly methane due to its possible ignition. Acknowledge of seam gas parameters is important for the prediction of gas emission rates into the ventilating air current. They are also important as the basis for the evaluation of the likely contained gas as a possible energy source.   Gas content determinations for the Kupakupa seam have been made at the Huntly West Mine.  Applying the method of Creedy (1986) to face samples, gas contents of 1.80 and 1.66 have been determined. Using desorbed and residual gas content data a content of 1.92 m3/t has been derived. These are on an ash included basis. Calculations using the adsorption equation of Kim (1977) and coal quality have given a gas content of 2.19 m3 t. Long-hole exploration drilling at Huntly West Mine has provided information on gas pressure. A pressure rise test has given a reading of 500 kPa (absolute); this is low compared with the pressure given for the determined gas content from theoretical adsorption isotherms.

Jan 1, 1991

By J Cornejo, A Pinochet, C Caviedes

The ore extraction rate and the incorporation of new areas are key operational parameters. In massive deposits mined by caving techniques they both control the cave back geometry, which is mostly responsible for the induced stress state around productive levels. Early detection of deviations from admissible geometries will prevent stability problems related to geomechanical hazards, helping to improve safety and working conditions and reduce the potential for lost reserves.This paper describes a mine planning tool currently in use at the El Teniente mine. This tool involves the control of the cave geometry based on rules that have been defined as a result of different studies and experience collected during the operational history of the mine.This mine planning strategy achieves an extractive mining process with lower risk than conventional planning methods, ensuring ore reserves extraction if followed as planned while reducing unexpected changes in mining sequences.CITATION:Cornejo, J, Pinochet, A and Caviedes, C, 2016. Geometric control for strategic mine planning at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016