Search Documents

By Emerson D. W

The search for economic mineral deposits is becoming more difficult as exploration goes deeper in the established mining camps and spread out to the surrounding covered areas, which may have an `overburden' some hundreds of metres thick. Geophysics is finding an ever increasing role in such exploration. When the target is zinc, the task often becomes even more difficult since sphalerite, the most commonly mined mineral, is non-magnetic, resistive, and relatively light compared to other sulphides. Fortunately, sphalerite commonly occurs in association with other sulphides, which are magnetic and/or conductive and/or heavy, thus most zinc-rich orebodies have at least one contrasting physical property to aid exploration. This paper presents the physical properties of sphalerite and other potentially important zinc minerals. Results of petrophysical measurements of samples from various zinc-rich ores are presented together with examples of geophysical surveys over a number of zinc deposits. The results show that the physical properties are not merely dependent upon the properties of the orebodies' constituent minerals. For example, the small (0.4 Mt) and low-grade (five per cent Zn + three per cent Pb + two per cent other sulphides) Flying Doctor deposit at Broken Hill, New South Wales (NSW) is much more conductive than the large (3+ Mt) and high grade (14 per cent Zn + five per cent Pb) Cadjebut deposit in Western Australia (WA). In the former case, tectonic stresses have

Jan 1, 1993

By O Ostrovski

Iron ore reduction and iron cementation by CH4-H2-Ar gas was investigated in a laboratory isothermal fixed bed reactor. Iron ore was first reduced to metallic iron by hydrogen, then carburised to cementite by methane. Increasing temperature and hydrogen content accelerated the reduction process. Methane had almost no effect on the reduction process. Meanwhile, higher temperatures increased the rate of cementation and also the rate of free carbon deposition. The optimal temperature for cementite formation was found to be 750¦C. At this temperature, reduction of iron ore to cementite by gas containing 55 vol per cent hydrogen, 35 vol per cent methane and 10 vol per cent argon was completed in about 15 minutes. Addition of sulphur into the reducing/carburising gas strongly retarded the process of cementite formation and free carbon deposition. Cementite is an unstable phase which decomposes to iron and carbon. The rate of cementite decomposition increased with temperature up to 600¦C and above 750¦C . In the temperature range from 600¦C to 750¦C the rate of cementite decomposition decreased with temperature. Cementite was the most stable at 750¦C and least stable at 600¦C. The two-interface grain model was used to describe the process of iron ore reduction and the volume reaction model was employed to model the iron cementation process. The simulated results for both reduction and cementation are consistent with the experimental data.

Jan 1, 2000

By Bulters J, Sheppard I

Two blasthole density logging programmes have been conducted on the Mt Whaleback iron ore mine to evaluate the use of this type of logging as an aid to blast pattern design. The first programme also involved the setting up of a Density Test facility with which to calibrate the density probe. The programmes indicated that about 22-23 blastholes can be consistently logged per day at a cost of $1.30 per metre. Even though this is only half the rate required to log the average number of blastholes drilled daily on Mt Whaleback, testwork indicated that no significant loss of accuracy results if only half the holes in a pattern are logged. The major results of the programmes were: 1. The density range for black pyritic Shale is 2.2-2,9 g/cc. 2. The density range for soft to medium hard BIF is 2.1-3.0 g/cc. 3. The density range for hard BIF is 3.0-3.6 g/cc. 4. The front row blastholes show consistently lower densities than the main body holes due to blast damage. 5. A low density zone extending to a maximum depth of 6 m occurs at the top of most blastholes and results from blast damage from the bench above. These density results have been used to implement savings in drilling and blasting via pattern expansion and charge optimisation of blastholes. Eight ore

Jan 1, 1986

By G C. Snedden

Tandem row stator arrangements are common in the last stage of multirow, gas turbine compressors. Tandem row stators, or stator and de-swirler vane combinations are used to relieve the loading on the stator but ensure axial flow leaving the compressor. In this paper a standard 40” (1016 mm) ventilation fan in the Air Blow Fan’s range is modified to utilise the plate support struts on the barrel to relieve the aerodynamic loading on the aerofoil stator. Performance maps for both versions of the fan were generated using computational fluid dynamics and are compared across a wide range of rotor setting angles showing a clear advantage of approximately 2 per cent in efficiency for the tandem blade design. In addition, the area of high efficiency that represents the practically usable area of the map extends over a greater area in terms of flow rate and total pressure rise.

Oct 12, 2022

By D Reid, A Fourie, J Ayala

This paper discusses cone penetration test correlations for loose gold tailings that were developed within a critical state soil mechanics framework. The development of a new calibration chamber for cone penetration testing that consists of a modified triaxial cell is described. Some of the early development and commissioning issues that were encountered, as well as the solutions adopted are outlined, including the system to prepare the samples and to acquire high-quality data from the testing. Also, the triaxial laboratory testing required to achieve the critical state line is described, including some of the basic precautions considered necessary as good practice. Additionally, the system adopted for volume tracking of the calibration chamber sample is described, which is essential for ensuring a reliable state parameter comparison against the acquired cone penetration test data. Finally, some laboratory test data from the calibration chamber is plotted against the soil behaviour type charts currently available from various authors.

Jul 1, 2021

By P Dean, M Elmouttie, Y Duan, X Luo

Slope instability is one of the major concerns in open pit mining operations. A significant collapse of the pit wall can result in injuries, damage to machinery and interruptions to production. A broadband microseismic monitoring technique has been developed for diagnosing the healthy condition of a target slope area. This technique has been successfully applied to an open pit mine in Chile. Our research has found that this microseismic monitoring technique can be used in open pits for tracking and locating a falling rock that is rolling on a slope, if a dedicated seismic sensor network has been established. In collaboration with other monitoring techniques (radar, laser scan, aerial photography), more accurate determination of rock rolling trajectories can be obtained. In this paper, an example of using the CSIRO microseismic monitoring technique at an open pit mine is presented. Results from an experiment where we used the microseismic technique for determination of the trajectory of a rockfalling on a slope are also presented.

Nov 8, 2021

By Lewis RW, Tullemans FJ, Gallo JB

Gold mineralization at Kidston occurs in a semicontinuous zone near the margin of a large, late Palaeozoic breccia pipe. The pipe is ovoid in plan, funnel-shaped in cross section and straddles a contact between Proterozoic metamorphic and granitoid rocks which are intruded by a swarm of late Palaeozoic acid dykes. Rock fragments within the breccia pipe reflect the enclosing country rocks and mix in various proportions to form gradational lithological domains. Most of the gold is free and is located in the breccia matrix and in a set of inwardly dipping sheeted quartz veins which kink around the pipe margin. Sulphide minerals, dominantly pyrite, occur as disseminations in the breccia matrix and as aggregates in the cores of quartz veins. Hydrothermal altLration is pervasive within the breccia and is most intense in areas with the highest percentage of acid dyke fragments. Sericite and carbonate are the main alteration minerals. An empirically developed genetic theory for the formation of the breccia pipe and attendant mineralization involves magmatic and post-magmatic processes associated with the intrusion of a granitoid body to a shallow level in the crust. Economic evaluation of the deposit relied heavily on the results of diamond drilling. Both polygonal and geostatistical reserves were calculated and found to be in close agreement. Geostatistical reserves are considered to more closely reflect the tonnes and grade achievable during mining. Daily geological mine routine is strongly biased towards grade control allied with the practical aspects of open-pit mining. Tonnage/ grade correlations between ore blocks geostat- istically generated from exploration diamond core results and ore blocks generated from high

Jan 1, 1986

Fluid inclusions and sulfur isotopic compositions were studied in a possible extension of the Toyoha polymetallic vein deposit. The objective of this work was to gain a better understanding of the ore depositional conditions, sources of ore constituents, and distribution of mineralizing fluid in the region. Fluid inclusions in sphalerite and quartz show that most homogenization temperatures range between 190¦ and 290¦C. Most salinities range from 0.0 to 3.4 wt per cent NaCl equiv. Sulfur isotopic compositions of ore minerals (pyrite, sphalerite and galena), determined by a conventional technique, range between 1.3 and 7.7 per mil. The mineralizing fluids were characterized by relatively low and various temperatures and low to moderate salinities compared to those at the southeast region of the main ore bodies (Izumo and Shinano veins) where rare elements such as tin, tungsten and indium occurred. Obtained temperatures and salinities were attributed to the mixing of hydrothermal fluids with groundwater. Sulfur isotopic data suggest sulfide sulfur was of magmatic origin. Isotopic temperatures, estimated from the isotopic fractionation factor between sphalerite and coexisting galena, are between 195¦ and 322¦C. The temperatures are only consistent with fluid inclusion homogenization temperatures in sphalerite or coexisting quartz when sphalerite was a honey-yellow coarse crystal lacking conspicuous colored growth bands. This suggests the detailed classification of mineral pairs growth textures will be necessary for precise in situ measurements to obtain reasonable eothermometric results.

Jan 1, 2002

The equipment and general smelter layout for the Mount Isa Copper Smelter were designed by engineers associated with the American Smelting and Refining Company and by Mount Isa staff engineers. The final notice of site was dictated by the need for 'building the smelter near the existing Mount Isa power house to enable full use to be made of the steam from the waste heat boilers. Although much excavation work was necessary before concrete foundations could be poured, the location lends itself to further expansion should it become necessary. The plant is designed and constructed to involve straight line smelting operations which include the following major steps in the overall scheme.1. Charge make-up.2. Roasthig.3. Reverberatory smelting.4. Converting.5. Refining.6. Casting.CHARGE MAKE-UPA system of proportioning bins is provided for preparing the feed mixture for the roasters, Sulphide concentrate containing 24% copper wiil be delivered by belt conveyor from the filter plant to the smelter storage patio. This is a large roofed concrete floor that provides a maximum storage capacity of 8,000 tons of concentrate. Eight proportioning bins located below but adjacent to the south end of the patio will be used for actual charge make-up from which concentrate, ore and flux will be proportioned to the feed belt and conveyed to the roaster feed hoppers. Four of the proportioning bins, 80 tons capacity each, will receive...

Jan 1, 1953

Gold mineralisation at Wapolu lies within an exposed arcuate zone at the decollement contact between a basement dome of high grade metamorphics and an overlying ophiolite sequence. This contact was originally a thrust fault which has since become a decollement zone for gravity sliding in association with basement doming. Hydrothermal models for the gold mineralisation postulate an epithermal system in which fluids were channelled up the decollement with boiling of those fluids causing hydrothermal brecciation and subsequent gold deposition. The alteration assemblages, fluid inclusion data and geochemistry indicate that the upper levels of the system are exposed.

Jan 1, 1987

By J Vann, C Seymour

Geology is generally treated as a æfront endÆ step in mine development. After infill drilling, the majority of resource estimation, mine-planning, development, mineral processing strategies and operational procedures are planned and implemented with little geological input, particularly in open pit operations. However, significant benefits in overall costs, cash flow, and technical risk reduction can be realised when sound geology is utilised more rigorously throughout the mining process. This under-utilisation of geology in the mining process has arisen due to a combination of factors:A lack of interest in, or knowledge of the full mining process by geologists. Few geologists fully understand where their inputs make critical impacts on downstream users. As a result of this, geologists generally do not focus their inputs towards areas of greatest value added, ie addressing issues critical for other members of the mining team. Most importantly, few geologists effectively communicate their results to the downstream users of their geology models. The results are that the potential benefits of geology, and the appropriate status of geology in the mining industry, are not fully realised. It is fundamental to realise exactly what geologists do. Geologists constrain geological processes and geometry. All geoscientific tools at the geologistsÆ disposal are geared towards one of these goals. An emphasis on geological processes is present throughout the exploration process, whereas in the resource estimation and mine development process an emphasis on geometry is required. The mining process is a web of disciplines that are attempting to optimise development of a resource to provide value to shareholders. Yet few people within these disciplines have a full appreciation of this web, and where sound geology inputs can add value through various feedback loops. Geology inputs do not end at the resource estimation stage, nor are they relegated to grade control implementation. If geologists have an appreciation of the mining process and close liaison with the other disciplines such as geostatistics, geotechnical engineering, hydrogeology, and mining engineering, they can significantly benefit project costs, timelines, and constrain technical risk by addressing their issues at the earliest possible stage. Furthermore, the mining process is not a single pass timeline, but an iterative process where the exploration, resource definition, mine planning and mining loop is continually repeated over the life of a project. Therefore, the potential inputs of geology are critical throughout the mining process. Effective communication of the impacts of geology inputs on downstream users is often lacking on mining projects. The most effective way to communicate geological results is through where it impacts most û project risk. Focussing all geology inputs and communication in terms of potential material risk allows the geologist to be more effective in contributing value to the mining process, and allows the downstream users of geology inputs to better constrain the risks associated with their aspects of the mining project. Through a program of geologists:taking an interest in the entire mining process and identifying critical areas for geology inputs to downstream users (the geologistsÆ clients); focussing geology inputs to address the potentially material issues on mining projects; and communicating their inputs to the æclientsÆ in terms of technical risk, geology will be much better integrated into the mining process. As a result, the potential benefits of geology throughout the mining process will be realised, and the status of geologists within the mining process will be elevated to a more pivotal position.

Jan 1, 2000

By P Kumar, J Safarian

Understanding how ore interacts with flux particles at elevated temperatures to create molten slag is crucial since it governs the dynamics of a chemical reaction. This study explores the smelting behaviour of pre-reduced Nchwaning manganese ore when combined with lime, with the objective of examining the evolving interaction between pre-reduced ore particles and lime over time. The research sheds light on the interaction between solid and liquid and the phases that emerge during this process. To achieve this, a sessile drop furnace was employed to rapidly heat the materials positioned adjacent to each other on an alumina substrate and to observe the smelting process as it unfolded over time. This method allowed for the direct observation of the melting temperatures and the flux-ore reaction progression rate, and the potential disruptive events that might occur. By comparing the molten interfaces of the fluxed materials at various time intervals, this study provides insights into the relative rate of slag formation from the two materials. The results indicate that the main slag formation initiated at approximately 1400°C and continued to advance with time, with complete mixing occurring around 1500°C. The possible phases formed were identified using Scanning Electron Microscopy and modelled using Fact Sage thermodynamic software. In addition, the iron particles in the pre-reduced Mn ore were separated and settled from a rich MnO-containing slag. It was found that the separation of molten iron droplets from the slag depends on the rate of solid MnO particles dissolution into the adjacent slag phase.

Jun 19, 2024

By T Berryman

The Fimiston reserve is being depleted at the rate of one million ounces per year; most of which is processed by the Fimiston plant, with the remainder being stockpiled. As for most other large open cut mines around the world, Fimiston has an excellent dispatch and tracking system. Reconciliation is used to determine how the various models used in mine planning (such as a reserve, budget and schedule models) are tracking against production. It is also used to gauge the performance of grade control estimation against production; however, analysing the results of this can be complicated and, at times, misleading. The reconciliation process involves adjusting the monthly production data to equal the mill reported tonnes and grade, plus the change in stockpiles. This adjusted number is then compared to the grade control reported tonnes and grade, the scheduled model (monthly planning model) tonnes and grade and against budget (Reserve) tonnes and grade. This paper includes explanations of all assumptions made in the reconciliation process, including the end of month closing stocks balance, the application of adjustment factors to the dispatch data to create a new balanced set of production data and the monthly sign off to comply with the Sarbanes-Oxley requirements of the North American owners. The reserve is reconciled by proved and probable classification. This tool is used to assess the robustness of the classification scheme utilised and identify any reconciliation issues as they arise. Within the Fimiston deposit there are still issues that are clouded by the assumptions made concerning the scale of observation, poor data support and the mining of the narrow lode areas of the deposit. The declared ore mined (DOM) number (which is defined in the paper) can be significantly affected by these assumptions, and these need to be clearly stated and understood when looking at the reconciliation data. The DOM tonnes and grade is a good indicator of real mine performance as it adjusts mined tonnes and grade to take into account the milled tonnes and grade each month, and prevents cumulative errors from building up in mine predicted dispatch numbers or end of period stockpiles. This number allows monthly monitoring of the mine to mill performance and allows valid comparisons to be made back to budgets and reserves over a period of time. KCGM uses three month rolling averages to monitor performance against reserve and budget models. This ensures that monthly distortions in the figures due to stockpiling issues or over mining in a particular period do not lead to false conclusions. Reconciliation performance over a longer period (12 - 18 months) is used to adjust reserve models should significant variance be observed. By closely monitoring the reconciliation performance at the Fimiston operation, fine tuning of all aspects of the grade estimation process from reserve through to grade control can be made. This allows the most accurate data to be used when planning from reserve data for the Life of Mine Plan through to grade control data for short-term mill feed.

Jan 1, 2006

It is always difficult to sum up an open forum adequately and instantaneously, so, with the privilege of hindsight, and also with some time to reflect, I am exercising the Chairman's prerogative to put together my view of the overall conclusions. Hopefully, these may provide a focus for each Institute to formulate its own programme with respect to mineral industry education. First, in answer to the question, "Should there be Schools of Mines?", there was a very clear 'yes'. However, I reiterate what I said in the introduction to this forum, specific professional education for the mineral industry exists only because the mineral industry sees a need and wants it. If the mineral industry should decide that it does not need professionals with specific mineral industry training, then such training will cease to exist. As alluded by Dr Hackett, if such training ceases to exist, one must then question the need for Institutes of Mining and Metallurgy. Now, there's some food for thought! Specialist schools of mines (metallurgy and geology) can only exist in an environment of genuine interaction with, and support by, industry. For their part, schools of mines, used here in a generic sense, require leadership that is strong but responsive to industry needs. It is the leader that puts his stamp on a school, and, to a large extent, determines whether that school is 'good' or only 'mediocre'.

Jan 1, 1986

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is an energy efficient way of grinding and a number of operations have utilised this in the design of their comminution circuits. Owing to the large flow of slurry through the mill that results from operating this way the grates and pulp lifters have to be designed to cope. However, the literature has little or no information on how grate and pulp lifter size and design are related to their ability to remove slurry from the mill. Over the last few years the JKMRC has been researching this area and has developed relationships between grate/pulp lifter design and flowrate capacity. At the same time it has determined the major causes of pulp lifter inefficiency and a solution to preventing this inefficiency (the Twin Chamber Pulp Lifter). This paper describes the models that have been developed through this program and uses industrial scale data to illustrate their accuracy. Results from the industrial trials of the Twin Chamber Pulp Lifter are also presented.

Jan 1, 2000

By M I. Pownceby, J Manuel, S Suthers, A Poliakov, E Donskoi, N Ware

"The mining industry is constantly seeking methods for optimising the exploitation of mineral resources, such as iron ore, in a sustainable and eco-efficient manner for economic and social benefit. When faced with resources that have mineralogical or textural complexity, poorer grades or geological variability, it is particularly important to apply a comprehensive geometallurgical approach to the development of the mining operation, from resource definition through to processed product. Integral to this approach is the quantitative characterisation of representative samples across the whole orebody.A key factor that associates the geological characteristics of iron ores to their processing response is ore texture. While the classification of samples on the basis of chemical or physical properties alone is often not sufficient to predict their processing behaviour, classification and quantification of texture types can be effectively correlated to metallurgical performance in processes such as blending, beneficiation, pellet making, sintering and ironmaking. This paper describes some of the research conducted by CSIRO pertaining to the design and rationale of a texture-based classification system for Australian iron ores; some of the tools developed and used to apply such classification; and the application of the generated data to quantifying, modelling and predicting sintering behaviour and performance in the blast furnace.CITATION:Suthers, S, Pownceby, M I, Manuel, J, Ware, N, Donskoi, E and Poliakov, A, 2016. Geometallurgical Characterisation of Australian Iron Ores – from Ore to Processed Product, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The perception of New Zealand as an exploration destination has improved compared with other countries. There has been a realisation that New Zealand's potential is greater than previously thought. Other countries are not as attractive as before, and explorers are looking at alternatives that are geologically prospective and politically stable.   New Zealand is regarded as geologically prospective, especially for gold, with potential for world class deposits. It is also prospective for other metals, coal and industrial minerals. New Zealand is politically stable, and has an economy that is attractive to overseas investors. It is one of the least corrupt countries in the world, which overseas companies see as providing a high degree of certainty for investment.   New Zealand has good opportunities for investment in gold exploration at present. Otago has been the focus for new companies and is the favoured exploration location. Otago is regarded as very prospective, and hosts New Zealand's largest gold deposit at Macraes. There is potential for other similar deposits elsewhere in Otago.   The mineral industry previously had an excessively pessimistic view of New Zealand, which has resulted in little new investment in New Zealand for some years. Previous pessimism is turning to optimism, and there is increasing interest in New Zealand as an exploration destination by overseas explorers.

Jan 1, 1997

Over the past 18 months the De Beers Consolidated Mines Ltd operations have made a concerted effort to move away from using the traditional shock tube initiating systems. These systems are being systematically replaced by the use of electronic delay detonators (EDD). Various trials were conducted in both host rock and kimberlite rock masses to improve tunnel advance as well as to optimise delay timing during trough openings (Ngoma et al, 1999; Mohle, 1999; Baltus, 2000). The high cost of EDDÆs, when compared with traditional initiation systems, led to a number of detailed studies being conducted on the mines where EDDÆs were being used. These studies aimed to quantify the additional benefits when blasting with electronic detonators. The studies showed that the change was justified on the basis of increased quality control and reliability gained through the use of EDDÆs. However, these benefits attract other related benefits, like fragmentation control, and backbreak reductions. When compared to the shock tube initiating systems the increased development face advance and the reduction of oversize during production blasting using EDDs, compared favourably to the less costly systems. As blasting engineers gained experience and confidence in the use of the system bigger blasts were initiated in mass under-cut blasts and slot raise development, by using multiple hole firing and second delay periods between holes. In the open pit and sublevel open stope mining methods the control of the fragmentation distribution and the effect of the mass of explosive detonated during a blast is detrimental to the loading and hauling production rates and the stability of the rock mass behind the blast. With a stable rock mass the bench cutting can be executed to establish steeper overall slope angles leading to large cost savings due to a reduction in waste stripping. It is the purpose of this paper to indicate through quantification that the use of the EDDs as an initiating system improves all-round blasting performances and assists in meeting customer requirements. The customer being the ore treatment plant.

Jan 1, 2001

By W A. Take, M McKellar, A Walsh, S McDougall, S G. Evans

Recent tailings dam failures have heightened public awareness of the hazard posed by storage facilities for mining waste, illustrating the need for a more critical examination of tailings dam breach mechanisms and the potential mobility of liquefied tailings. Knowledge from tailings dam breach studies will help improve safety and risk management through more accurate inundation maps, dam consequence classifications and emergency preparedness plans. Tailings dams differ from conventional water retaining dams, although dam breach relationships used in practice rely heavily on relationships derived for breach processes from the latter. Physical modelling offers a controlled environment to advance the understanding of tailings dam breach processes, thereby allowing for modelling of simple geometry and boundary conditions to test hypotheses. The performed experiments investigate prototypical tailings dam configurations and material behaviour, with the objective of validating numerical models that will enable practitioners to better assess and mitigate tailings flows resulting from tailings dam failures. Research conducted in the Queen’s University Landslide Flume at the Coastal Engineering Laboratory has investigated the breaching of 1 m high dams with tailings geometry by overtopping initiated by a v-notch incised in the dam crest. This paper presents the initial results of the next stage of this research comparing the outflow hydrograph following loss of containment caused by shear failure to overtopping initiated by notch flow. The two dam experiments presented are constructed with similar dam and reservoir geometries allowing for a direct comparison of the effect on the outflow hydrograph of each failure event. Preliminary outcomes suggest that although both dam failure events are triggered from separate mechanisms their geometries allow for similar values of Q_peak to be reached. Future work is currently planned to expand the shear test series to explore the influence of failure mechanism on the outflow hydrograph.

Jul 1, 2021

A generalised mathematical model for hydrocyclone classifiers was developed by the author (Nageswararao, 1978) using dimensionless groups which include phenomenological characteristics as independent variables. This model is incorporated in JKSimMet, the steady state mineral processing simulator developed by JKTech.Recently, when this model was rewritten (Lynch and Morrell, 1992), in terms of variables other than those used by the author, a few errors have crept in. For example, while the exponent of (Du/Dc) in the equation for d50e should be negative (-0.47), it was recorded as positive (0.47). Also, the exponent of (DoIDe) in the equation for pressure drop should be 0.67 and not 0.60. In the same equation, the exponent of Dc would turn out to be -0.10 and not 0.15. These are clearly attributable to typographic and rounding off errors, while transforming the original equations.More recently, Cilliers (pers comm) has done a comprehensive evaluation of the major semi-empirical models for hydrocyclones.He observed that the major difference between the cyclone model developed by the author and other models lies in the method of quantifying the effect of spigot diameter on d50e. He noted that while all other models predict an increase in d50e with a decrease in the spigot diameter, the model as cited by Lynch and Morrell (1992) predicts just the opposite. However, he conjectured correctly that the discrepancy could be due to a typographic error. As the model is still unpublished, it is felt that the original model equations should be recorded with the correct exponents, so that errors in predictions other than those due to the limitations of the model itself could be avoided. They are given hereunder.

Jan 1, 1995