Search Documents

Management at all levels continually strive to optimise, or make the most of resources available to them. Daily, decisions are being made on how to most efficiently locate and exploit an ore body, then process and market the recovered metal. At one level this optimisation process in the Australian mining industry appears to be successful, for example, witness the improvement in productivity and reduction in operating costs through the 1980s. Yet, at another level the industry's performance has been appreciably below expectations as measured by rate of return criteria. Companies likely to exhibit superior performance are those that are able to co-ordinate, through good planning, the optimisation process at all levels of the organisation. An important role for general management is therefore to provide the context or boundary conditions in which optimisation can Proceed.

Jan 1, 1991

By D Monaghan

Pumping water for dewatering and water supply is a major component of electricity consumption at mining operations and hence is a significant contributor of greenhouse gas emissions. Pump systems at a typical mine site can be broadly split between above ground centrifugal pumps (generally used for water transfer) and submersible borehole pumps (generally for dewatering and/or water supply). In contrast to above ground pumps, submersible borehole pumps can be subjected to varying duty points (total pumping head and flow requirements) as a result of changing bore water levels and yields, particularly in mine dewatering bores. Typically, much higher pumping rates are required at the commencement of dewatering to remove groundwater storage and to intercept sufficient groundwater throughflow to achieve target drawdowns. Once target drawdown levels are reached it often only requires much lower pumping rates to maintain target drawdowns. Pumps sized to remove the large initial volumes of stored groundwater often end up too large for the lower flow rate required for æmaintenance pumpingÆ. This often results in pumps operating inefficiently, a problem which can be made worse when pumps are throttled to reduce the pump output to better match the reduced bore yield. Current standard operating practice places little emphasis on the electricity consumed by pumps, with the focus often being on minimising capital expenditure (æIf it ainÆt broke donÆt fix itÆ). Submersible pumps can have extended service lives of ten to 20+ years. However as the capital cost of a pump typically represents only five per cent of the life cycle cost, the vast majority of the life cycle cost is energy usage.Through the implementation of a regular review of the operation of borehole pumps, significant reductions in electricity use and associated greenhouse gas emissions can be achieved without impacting the dewatering schedule. In most cases, the capital cost of replacing pumps is more than offset by savings in operating costs. These potential savings become even more significant when considering proposed future carbon tax levees.This paper presents examples of the opportunities for significant reductions in energy, greenhouse gas emissions and overall costs that can be achieved for a range of dewatering scenarios.

Jan 1, 2009

By D A. Shushkov

Analcime-bearing rocks are one of the varieties of raw zeolite material, although the characteristics of analcime are not as good as other kinds of zeolites such as clinoptilolite or mordenite. However, some fields of application of analcime-bearing rock have been found, eg a method of water purification has been developed and patented. Analcime-bearing rocks are rather widespread in the Timan region of the Komi Republic of the Russian Federation. They are represented by Upper Permian siltstones and mudstones. The analcime-bearing rocks have the following mineral composition (per cent): clay minerals (50 - 70 per cent), quartz (ten to 30 per cent), analcime (one to 30 per cent), feldspars (two to ten per cent), carbonates (two to five per cent) and pyroclastic material. Analcime aggregates encrust cavities and infill microfissures in rock. Both microcrystalline (crystals <0.01 mm in size) and medium-crystalline (~0.5 mm) aggregates are observed. The mechanical, gravitational, magnetic, sorption and ion-exchange properties of analcime-bearing rocks have been studied. They are characterised by a high index of grindability and a low index of abradability and crush resistance, low values of the benzol-based pore volume and toluene-based specific surface area, and a medium porosity value. The magnesium based ion-exchange capacity (IEC) ranges from 28.7 to 196 mg+equiv/100 g. Analcime-bearing rocks of the Timan region are characterised by low beneficiation potential. Preliminary ultrasonic treatment of the analcime- bearing rocks is efficient for the destruction of intergrowths along their boundaries and production of free analcime aggregates. The proposed beneficiation procedure yields 95 per cent analcime concentrate. In the Komi Republic, analcime-bearing rocks are utilised in agriculture. They are also used for domestic needs (eg as biotoilets for domestic animals) and the solution of ecological problems (regeneration of soil polluted by oil). We have completed experiments on the purification of potable and industrial water using analcime-bearing rock subjected to thermal treatment. The experiments demonstrated that it was possible to decrease water colouration by 20 per cent, turbidity by 79 per cent, permanganate oxidation by 30 per cent and total iron content by 70 per cent.

Jan 1, 2008

By P Church

What is the best method of splitting a sample from a reverse circulation drill rig? How important is it to obtain a correctly split sample? What is the impact of an incorrectly split sample? These are just a few of many questions asked daily in the mining industry with regard to sampling. Modern sampling theory is well described in the literature in texts and is taught in short courses throughout the world, however little has been published on the relative performance of sample splitting devices used in the field. This paper compares the performance of the Jones tiered riffle splitter with a cone splitter manufactured by SGS Metal Craft in Western Australia. The testwork was carried out at AnglogoldÆs Sunrise Dam Gold Mine, 55 km south of Laverton in Western Australia. Mineralisation at Sunrise Dam is hosted in a structurally complex framework of shear zones with dips that range from steep (70¦) to shallow (25¦). The deposit is characterised by significant amounts of coarse gold, which presents a challenge in sampling, analysis and grade estimation. The three major areas where sampling errors can occur are in drilling, sampling, sample preparation and analysis. Sampling errors attributable to drilling and sample preparation often far outweigh the errors made at other stages in the process, however historically most effort to identify sampling errors has concentrated on the laboratory and analytical procedures. Splitter design and cleanliness can have a large impact on sample collection and preparation. Splitter performance was tested with respect to sample weights, particle size distribution, and gold grade consistency. The aim was to determine if each particle has an equal probability of being sampled, the resulting sample has integrity, and if any segregation problems occurred. The cone splitter was found to provide the best split in terms of particle size distribution, with no apparent size bias. Duplicate samples had more comparable masses than those provided by the riffle splitter. Most importantly, the cone splitter gave less grade variability between duplicate samples than the riffle splitter. Testwork also confirmed that, like the riffle splitter, the cone splitter must be oriented vertically and the design of the rig or cone splitter trailer should accommodate this requirement.

Jan 1, 2003

By P Stoker

The need for quality assurance and quality control (QA/QC) in the sampling and assaying of minerals is fundamental to the reliability and confidence of a mineral resource estimate, reserve estimate and possibly profitability of a mine. In spite of this, QA/QC practices in the mining industry are commonly applied poorly, or misunderstood. As New Leaders, we should aim to correct the poor practices and become fully informed on appropriate procedures. This paper uses worked examples that show the usefulness and importance of best practice QA/QC procedures. Fundamentals of reviewing the performance of the laboratory by examining the results of client inserted standard reference material (standards), blank material and duplicate samples are discussed. To do this, three examples from Australian data sets have been used. For each example, simple and efficient plotting techniques are suggested with subsequent evaluations of each plot. The first case study compares the results of internal standards from a laboratory with blind standards (where the expected value is unknown to the laboratory) submitted by the client. It was demonstrated over time that the laboratory was unintentionally analysing the internal standards in a different manner to the remainder of the sample batch. In this example, not understanding the cause of a high negative laboratory bias could have led to poor understanding of the depositÆs grade and in the extreme a proposed mining operation may have reached operational stage with a subeconomic grade. The second case study discusses the quality of blank material submitted by a mining operation to monitor cross-contamination within the laboratory. The blank material contained background levels of the element under investigation. This created uncertainty in the assay results, which could have led to the need for additional assays and drilling programs. Finally, the third case study demonstrates the use of the relative paired differences (RPD) technique to cross-validate the results from duplicates and repeat analyses from two laboratories. The three examples given show either laboratory or operational error. If left undetected, each example could have had serious implications for the mineral resource estimate and ultimately, the mining operation. These examples are not isolated occurrences; poor QA/QC practices are an industry wide problem exacerbated by rapid staff turnover and increased contractor positions on-site. New Leaders must be equipped with a thorough grounding in QA/QC best practices to improve its application and confidence in the results of sample analysis.

Jan 1, 2009

This paper is directed at the problems flowing from Australia's capital gains tax (CGT) on the disposal of exploration and mining tenements both in Australia and overseas. It will seek to identify the issues and give some idea of the dollar consequences of decisions lacking forethought. The paper should not only be seen in the context of Australian tenements. CGT applies to the disposal of any assets by an Australian resident anywhere in the world. Offshore incorporated companies are not necessarily free from CGT risk where it can be shown that control management and control of the relevant company is in Australia. Also the disposal by non residents of Australian tenements are potentially caught by CGT. Some will ask what has taxation got to do with a valuer who merely determines the value of assets. These days no determination can be blind to the consequences. Whether the consequences can encourage a movement in value is another thing dependent upon the circumstances; but? A role of an experienced taxation consultant is to point out parameters within which associated professionals can work. The parameters will vary from case to case, but these when clearly indicated may be of help to persons such as valuers. When one comes down to it real estate salesmen are never wrong. They have a feel for the market and almost through self fulfilling prophesies achieve sales at their guestimates. Whether they could have achieved higher considerations become virtually academic in the process. Of course I am not suggesting that tenement valuers can be compared to real estate salesmen, or am I? What is the value of a tenement? Is it the DCF/NPV type of generated value based on a large number of variable factors (ie what one may call the fundamental value)? Or is it what another may pay to purchase that tenement if it were on the market at an instant point in time? How big is the market, the quality of the bidders, the size of their purses, the needs of the buyer for comfortable fit, the premiums for foreigners, the standard of the marketing, the industry intelligence level of the bidders, the obligation to farm/sell down? The list goes on endlessly. One question must be.asked-"Is a range of values acceptable for tax purposes". ie Would any tax consultant ever provide a valuation to the Australian Taxation Office that indicates three or more possible values ie

Jan 1, 1987

In order to maintain an accurate survey underground, it is first necessary to connect all shafts used for the transferring of the survey to the levels below by a precise surface survey.This has been achieved at Mount Isa by a careful triangulation survey with stations adjacent to those shafts most suitably located for transferring the survey below.The precedure used is described herein.The Weisbach triangle commonly used is obtained by reading to swingirig wires, the theodolite being placed in line with them as nearly as is possible. The surveyor at the surface places the wires in the shaft as far apart as the size of the shaft will permit, with sufficient space between the wires and walls to ensure their swinging freely. The far wire is fixed in position, while the near one is movable by means of fine adjusting screws to facilitate its being brought into line with the fixed wire and the theodolite. When this is done the surveyor at the lower level is advised by pre-arranged signals and the survey can then commence.The surface portion of the survey is simple; all that is necessary being to read the angle from the backsight to the wires, measure their distance from the theodolite, and keep a check on them throughout the survey to make sure that no movement takes place.The lower portion of the survey is more difficult, the surveyor first qf all having to place his theodolite as nearly as possible in line with the wires.

Jan 1, 1953

By Grady PO

The longwall panels at Clarence Colliery have experienced intermittent sudden weightings on the face that have caused some production delays. These weightings have typically been more severe on the wider faces. A program of surface subsidence and extensometer monitoring was undertaken above Longwalls 4 and 5 to investigate the behaviour of the overburden strata during longwall extraction on two faces of different widths.The monitoring indicated that a dome shaped zone of large downward movement extends up into the overburden strata to a height equal to about the panel width.

Jan 1, 1998

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

By Williams DJ

Preliminary calculations suggest that spoil piles in the Bowen Basin will undergo approximately 4 m settlement as the ground water table recovers after mining is abandoned. Approximately 1 m of differential settlement is possible. Superimposed on this will be a long term creep settlement of 1-3 m/log cycle of time. Depending on the nature of the spoil material, partially submerged spoil piles could be sufficiently stable although to ensure stability during long term creep it may be necessary to flatten the final spoil pile face to approximately 25¦.

Jan 1, 1987

A system of decline mine entries and ore haulages has been designed for the Mt. Windarra mine. This choice was controlled by the nature of the ore- bodies, the mining method chosen and the capital cost of development re- quired for production. Mine entries are being driven 4 metres high and 5.5 metres wide and decline at 11%, to accommodate diesel haulage vehicles of 35 tonnes capacity. The.Mount Windarra haulage system and the design parameters used in its selection and design are discussed, and general design and selection parameters are proposed.

Jan 1, 1973

By Groudeva VI

The biohydrometallurgy of gold is based on different processes which could be grouped into four main groups (Attia, Litchfield and Vaaler, 1985; Karavaiko et al, 1988; Groudev, 1990): 1. bacterial oxidation of gold-bearing sulphide minerals by chemolithotrophic bacteria to facilitate the subsequent chemical extraction of gold; 2. solubilisation of gold from oxide ores by means of heterotrophic bacteria; 3. recovery of gold from solutions by biosorption; and 4. microbial modifications of the surface of gold-bearing sulphide minerals to improve the subsequent gold concentration by physical dressing methods (eg flotation, oil agglomeration).

Jan 1, 1993

This paper presents the results of studying the influence of catastrophic failures arising in mines, on the behaviour of mine ventilation systems. It is very important to take account of this influence for the stable operation of the system and to ensure mine safety when mining underground coal and ore deposits.

Jan 1, 2003

Multiple regression analysis applied to ventilation records of stopes on the Witwatersrand showed that it was possible to estimate the temperature increase per 100 ft for a new stope with a standard deviation of 0' 5°F. The analysis also threw light on the relative effect on this estimate of five different factors.Application of the analysis of variance technique to a factorialexperiment on the production of dust during rock drilling showed that the effects of air and water pressure were quite small but also showed that the between-machine variation was unexpectedly large.Analysis of variance also proved a valuable means for assessing the bias and random error variation of aneroid barometers used in pressure surveys.INTRODUCTIONThree examples are discussed to illustrate the use of the techniques of "analysis of variance" and "multiple regression" in research on the ventilation of gold mines. Although the techniques are basically similar their application to each example has a slightly different emphasis and the examples were chosen for this reason. The variation ofemphasis is as follows.1. Temperature increases in stapes. This work was undertaken as a preliminary to possible extensive controlled experimentation (Lambrechts, 1959). Data collected in routine work by the mine ventilation personnel were used for analysis and no specific experiments were carried out. The main object was to see whether such data could provide any strong pointers to factors which might be worthy ofmore careful study and to factors which could initially be ignored. Of course, there was hope that the study might provide an empirical formula for rough forecasts.

Jan 1, 1962

Analysis of the 2001 Australian census data set can be used to gain a detailed insight into the trends and levels of employment in different industry sectors. There is a common perception that employment of geoscientists within the mining industry and indeed across all industries has decreased significantly. However, the data shows that the number of individuals stating that they are geoscientists employed across all industries has decreased by only five per cent from 5336 in 1996 to 5067 in 2001. Within the mining industry (Australia and New Zealand Standard Industrial ClassificationÆs û ANZICÆs mining class), the number of geoscientists employed has decreased by ten per cent from 2701 in 1996 to 2441 in 2001. These figures, while showing a decrease, do not reflect the magnitude of the decrease commonly perceived. However, further analysis shows the number of geoscientists employed in mineral exploration may have decreased significantly more.

Jan 1, 2003

By Bourne R. W, Smith T

This paper presents initial findings of a project examining novel processes for the treatment of refractory sulphidic gold concentrates. Non-oxidative roasting of such concentrates for 12 hours at 750¦C resulted in the finely disseminated gold agglomerating to form discrete grains. The pyrite and arsenopyrite decomposed to form pyrrhotite, whilst the labile sulphur and arsenic driven off was collected on a condenser as a mixture of elemental sulphur, metallic arsenic and various arseneous sulphide compounds. As a result, the cyanide solubility of the gold contained in sulphidic refractory gold concentrate from the Emperor mine in Fiji improved from 54.5 per cent to 98.4 per cent; from the Fimiston mine in WA (65.2 per cent to 96.6 per cent), from the Windarra mine in WA (69.6 per cent to 91.3 per cent), from the Harbor Lights mine in WA (20.4 per cent to 60.7 per cent), and from the Wiluna mine in WA (12.6 per cent to 28.0 per cent). The non-oxidative roasting conditions have not been optimised for each of these minerals. Subjecting the non-oxidatively roasted minerals to mild oxidative acidic iron sulphate pressure leaching (with typical temperature of 100¦C and typical oxygen overpressure of 500 kPa) to remove iron and so further liberate finely disseminated gold, resulted in the cyanide solubility of the gold exceeding 96 per cent for each of these five concentrate types (including those from Harbor Lights and Wiluna). Thiourea leaching of the sulphur-rich residues under acidic conditions resulted in remarkably high gold extractions being achieved. These novel processing options need to be optimised, and their economic viability established.

Jan 1, 1991

The ore deposits investigated are composed primarily of hcmatite and can be grouped into three categories depending on the amount of leaching of silica and carbonate which has occurred from the original iron formation, and on the amount of recrystallization of the hematite. Minor constituents are magnetite. goethite, and quartz.Texturally. there are five different types of hematite, formed at different stages during the genesis of the ores.These are1. anhedral hematite grains formed by recrystallization of hematite already present in the original iron formation.2. hematite formed by martitization of euhedral magnetite, 3. massive aggregates of fine- to medium-grain hematite formed by recrystallization of (l) and (2).4. tabular or prismatic hematite grains occurring around the boundaries of the massive aggregates or martite euhedra. and in fractures and5. specular hematite. which is present in fractures in ore types (l) to (4).Minor and trace-element analyses, determined using an electron-probe microanalyser. indicated that only silica (less than 0·01 per cent) and cobalt (less than 0·002 per cent) were present in the magnetite and hematite from unaltered iron formation and in the hematite from the ores. Low concentrations of trace elements are typical of magnetite in ores formed as marine precipitates. On the basis of the analyses alone. it proved impossible to distinguish between the five hematite types. A determination of the variation in rare-earth trace element contents between iron oxides in the iron formation and iron oxides in the ores indicates that the rare earths were depleted during ore formation. A possible explanation is that they were removed in solution with silica as it was leached from the iron formation.

Jan 1, 1971

The common notion that the Box Hole Bore mineralization represents a variant of the Mississippi Valley type, has not been supported by the present investigation. Most of the common characteristics of Mississippi Valley type, namely 1. saturated saline brines; 2. low temperature domain; 3. mineralization in intraformational breccias and collapsed anticlinal structures; 4. hydrocarbon-rich or foetid carbonates, and 5. very simple geochemistry seem not to be applicable. The Box Hole Bore mineralization features: 1. moderately saline brines (18% NaCl); 2. very high temperature (495¦-520¦C) and low density brines, of critical vapour:water ratio and low pressure of formation (700 bars); 3. mineralization confined by faults and ex- tending laterally into carbonates of high pore volume such as stromatolitic dolo- mites; 4. ore environment characterized by oxidizing conditions, such as ferruginous carbonate and silica sands of high energy environment (heavy mineral banding) and 5. more complex geochemistry than is normal for Mississippi Valley type deposits (copper sulphosalts, and appreciable silver content). Additionally, the ore has un- usual textures formed by the replacement of carbonates and barite by large idiomorphic galena crystals. The pressure and temperature domains of the Box Hole Bore mineralization indicate post- Devonian emplacement and local high heat flow, possibly related to the Alice Springs Orogeny. Because of high lead and zinc trace element con- tents (100-600 ppm) of the carbonates, even out- side mineralized areas, it is possible that the mineralizing fluids have derived their metal con- tent from a local source, possibly aided by evap- oritic concentrations of the tidal to supratidal sequences. The new model for Box Hole Bore gives treater importance to the confining faults.

Jan 1, 1984

By Wang J, Ma Y, Jia H

The Hedong Gold Mine is located in the Yan(ai area, tihandong hroo%ill, e. China. It is an underground mine with an annual gold output of some 700 0(H) grams. The orebody is located on the edge of the Wanger Shan metamorphism zone, and the hangingwall of orebodies is thus defined by a prominent set of fractures. The proximity of the metamorphism zone and the inclusion of the fracture set ensure that both the orebody and the country rocks are unstable. The main orebodies dip at an angle of between 40 to 45¦, with a strike length of 160 metres and a horizontal width of 50 metres. Surface subsidence in the area is not permitted. Cut and fill mining is usually practiced. As the mining operation proceeds to greater depths, the ore grade is diminishing and it is necessary to find a more efficient stoping method. Sublevel open stoping with sequential extraction and filling of each sublevel has been designed and applied in situ. This new mining method is called 'sublevel open and fill stoping method' in the mine. Experience to-date is that new mining method is Satisfactory.

Jan 1, 1998

By E Werner, B R. Leavitt

The chemistry of acidic mine drainage discharging from flooded coal mines is commonly reported to improve with time after flooding. This investigation describes a 18-year dataset of post-flooding water chemistry for a below-drainage underground coal mine within the northern Pittsburgh coal basin (Pennsylvania, USA). The Montour mine is a 5650-hectare below-drainage coal mine of maximum 260 metres depth. Montour was closed in 1980 and flooded to within 38 metres of land surface within 4.8 years. Pumping averaging 210 L/s was then employed to maintain water levels at this elevation. The flooded proportion of the mine (by volume) at full flooding was 56 per cent. The shaft where water was pumped from Montour for water control is located about 70 per cent of the distance between the mine water table and the back of the mine ù that is, it is close to the back of the mine. The residence time (total water volume at flooding divided by pumping rate for control) is estimated at 5.6 years. Time series of chemical analyses show three phases of chemical behavior in post-flooding discharge. In Phase I (zero to two years after flooding), iron concentrations were high and reached their maximum (1100 mg/L). In Phase II (two to four years after flooding), a transition was begun to alkaline conditions, with decline in iron and other solutes. In Phase III (>4 years), net alkaline conditions began, with iron concentrations declining exponentially to 50 per cent of mined volume. This attainment of net alkalinity in this case may have also depended on abundant calcite in overburden extended up to 30 m above the mine floor.

Jan 1, 2003