Search Documents

By Colquhoun L

Flooding velocities were measured in a laboratory column (96 mm 4) provided with both bottom and side air entry Packings used were 6 mm glass rings and spheres and -16 +8 mm coke. Results showed that when air was introduced through side nozzles flooding velocities were much higher than those obtained when air was introduced at the bottom of the column. Significance of the results and application to blast furnace flooding is discussed from the viewpoint of assymmetric gas flow.

Jan 1, 1975

By Smit J. G

Following an increase in the number of methane ignitions in South African coal mines a new ventilation system was developed. The "Hydravert" system conceived in late 1979 for use in low seam coal mines, where the bord and pillar method of working is used, has been extensively developed to include applications for mining seams up to 4.5 metres high. A brief history of the development is supplied including some of the pitfalls encountered in the hydraulic equipment design and selection.

Jan 1, 1988

By Will D. P

A 328 m, 2.4 m diameter raise-bored shaft has been equipped with a modular ladderway system to provide a second means of egress from Aberfoyle's Hellyer Mine in Tasmania. The modular ladderway consists of platforms, ladders and service pipes assembled at the surface and progressively lowered down the shaft. This system provides a rapid, safe and economical non-entry approach to equipping a shaft. The modular construction and single suspension allows for future extension or for reuse in another shaft.

Jan 1, 1988

By R Willis, D Cooke, G J. Davidson

Mine-groundwater interaction at the Pasminco Rosebery Mine (PRM), western Tasmania, deserves special attention due to the unique climate and mining environment present. High rainfall and low evapotranspiration result in an excess of water, an uncommon problem at Australian sulfide bearing mines. Research is being undertaken to delineate current subsurface fluid flows and predict future fluid flows in order to improve management after mine closure. Acid mine drainage generation is well developed in abandoned mines throughout the area. If acid mine drainage is not controlled after mine closure, significant environmental degradation could occur in the receiving waters of the Pieman River system. The study area encompasses the heavily forested Mount Black, and underlying PRM workings. Groundwater flows beneath Mount Black through a crystalline fractured rock aquifer with faults and underground mine workings observed to act as the major hydraulic conduits. Recharge is controlled by local precipitation, and the ultimate discharge is thought to be the Pieman River system, which forms the topographic low in the area. Slug tests have been used in conjunction with the mineÆs extensive geotechnical database to spatially evaluate variation in hydraulic conductivity. In fractured rock terrain associated with mining, rock quality designation data can be a useful tool in delineating areas of similar hydraulic conductivity when combined with conventional hydrogeological methods. A GIS, mine planning software, an environmental and a geological database are linked to form the input for groundwater modelling.

Jan 1, 2003

By Wu H. W, Just G. D

Australia's mineral resources boom in the two decades up to 1980 saw the establishment of about 25 new mining towns across the continent Quality housing and a high standard of community services were incorporated to attract a labour force for the major mine or mines i eing serviced. Town construction costs were high and were principally born by the private enterprise mine developer. There has been a change in the pattern in recent years and over 20 new mine developers have adopted a fly-in fly-out arrangement rather than construct new towns. Employees are drawn from a home base which is typically a large city, coastal community or established mining town and flown to the mine site for intensive work periods of about two weeks. The change has occurred for many reasons. Mining companies have been unwilling to support the high construction costs of towns, short life and smallermining operations do not justify a town, fast jet aircraft are available and there is a better perceived family lifestyle in established (coastal) communities. On the other hand reduced permanent development at new mine sites does not assist Australia's perceived need for decentralization. There have been questions as to the social problems which may develop from the artificial separation of the "breadwinner" from his family. The paper reviews a recent survey of the attitude of Australian mining companies employees, governments and unions to fly-in fly-out arrange- ments. The support for this approach is analysed and conclusions drawn that the concept is likely to be with the Australian mining industry for some time in the future.

Jan 1, 1991

By P Cameron

Many products and technologies have been developed from outcomes of research projects carried out by the Julius Kruttschnitt Mineral Research Centre (JKMRC). When these products and technologies are applied to the design and optimisation of blasting, comminution and separation, improvements in profitability can be realised. In 1970 Alban Lynch promoted two practical ideas to improve plant operations: Ore and equipment properties can be separated allowing experience with one type of ore or equipment to be transferred to other types of ore and equipment. If this experience was encapsulated in a mathematical model, then these properties could be combined and used to simulate (ie to design and to optimise) complete mineral processing circuits. Many problems associated with scale-up from laboratory to industrial equipment could be eliminated by experimental work on full-scale equipment in the plant. Many JKMRC research projects have focussed on the development of models of unit operations in mineral processing and their application to process simulation. Models of comminution and classification developed at the JKMRC have been used since the early-1980s. Ore characterisation techniques developed to support these models are licensed world wide through JKTech. The application of comminution modelling techniques to blasting, which optimises the process feed size distribution is used in Mine-to-Mill? projects. The advances in the understanding and modelling of froth flotation over recent years have provided the opportunity for integrated ore characterisation and process optimisation from resource to product. JKMRC project outcomes often provide proven opportunities for the mineral industry to improve performance and productivity. JKTech was established in 1986 to commercialise and market the most promising outcomes and thus ensure their continuing availability to the mineral industry. These include: commercial software (JKSimMet, JKSimBlast and JKMetAccount); monographs (Comminution and Blasting); technologies (Mine-to-Mill? and flotation optimisation); and hardware products (JKFrothCam, JKJetLift? and the Mineral Liberation Analyser). This paper summarises these technologies and their benefits.

Jan 1, 2002

Through partnering with mining customers, DYNO has been able to develop some specific technologies that benefit blasting operations particularly in underground mining. Some of these areas are: 1. Cost allocation and product tracking systems; 2. Borehole video surveys of breakthrough blastholes; 3. Borehole video photography for logging VRM blastholes; 4. Toe-load uphole loading for sublevel cave mining operations; 5. 3D blast modelling for underground ring blasting. This paper outlines these developments in the context of a Canadian underground metalliferous mine.

Jan 1, 1995

By Willett, Jacka

Group 3 were asked to discuss the treatment of spontaneous combustion. Before discussing specific cases we agreed that certain preliminary information should be available. The following questions are typical of the information which might be requested: 1. Have workmen been withdrawn? 2. Have gas samples been taken? 3. Is the mine gassy? 4. What are the details of water supply? 5. Are mine plans available? 6. What equipment is available? We discussed treatment in four different circumstances as follows: 1.

Jan 1, 1973

By Van Rooyen F

An introductory review of the current grade control blasting techniques (selective mining strategies) used in the Eastern Goldfields has recently been undertaken. The survey was initiated and conducted by the Western Australian School of Mines. Four distinct selective mining strategies have been identified and a number of trends have been highlighted. Many operations, however, have developed techniques which use a hybrid method to suit the site conditions. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and experiences no mixing of the various identified ore and waste blocks and is fully reco- vered at the minimum overall operating cost. Due to this unified aim all of the grade control blasting techniques have many common design Features.

Jan 1, 1988

By R Polmear, G Mauger

You wouldnÆt start excavating before testing core samples, so why would you approve a project plan before all factors have been identified, reviewed and addressed? Even a champion sports team made up of the best players canÆt produce optimal results without a well understood and agreed game plan. Could an F1 racing team produce their outstanding performance without rigorous evaluation and testing of the factors for successful performance? Why would we expect a capital works project team to be able to get it right without an understanding and an involvement in setting and implementing the overall game plan and without an understanding of all stakeholder requirements? For International PowerÆs Hazelwood (IPRH) mine in Victoria, the challenge was development and delivery of a 40 year mine plan, ultimately involving relocation of existing mine operations into an adjacent new coal field, land acquisitions and major environmental and other approvals to allow diversion of three streams, a highway, an Over Dimension route and other infrastructure in a political and environmentally sensitive atmosphere. The lessons from International Power HazelwoodÆs (IPRH) experience are: that the clear set of project principles and guiding values ensured delivery of a robust plan; a robust plan can withstand significant change; and value management (VM) played an important role in providing assurance, to all, that the plan was sound at both the strategic and micro levels. This Hazelwood mine project included five major VM workshops. The first was a critical review process in addition to design and cost reviews. This VM workshop was used to analyse, at a high level, the preferred coal mining sequence and design concepts, together with the interaction between design elements, risks and costs. In addition to this, the workshop provided an agreed common pathway for all downstream decisions. A second VM study was conducted to ensure that the proposed plan and design for relocation of the conveying systems from the existing mine into the new field were planned for optimum achievement from a whole of life cost, time, operational and maintenance perspective, plus the logistics of continuing operations while relocating assets. A third study followed to review the Conveyor Transfer Alliance and review functional design. A fourth VM study workshop was formed at the start of Phase 2 Alliance to ensure that the best value for money was being achieved through the current design, schedule and project arrangements and that all interfaces between parties had been reviewed and responsibilities were clear and understood. Other studies are outlined later in this paper. This paper details the evaluation criteria and processes used in the project evaluation that led to the WestField Mine Development.

Jan 1, 2007

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

By Dunne RC

The physical properties of an orebody require determination for virtually all mining projects, new and existing. The extent and regularity of such determinations being subject to the size and homogeneity of the orebody. Such properties have an impact at the design stage of new plants, with respect to equipment specification, and thus effects capital costs; and also impacts on the operating costs of new and existing plants, with respect to power consumption, production levels and part replacements. All of these can severely alter the bottom line and can be the determining factor in the economic viability of many projects.This paper examines some of the most common properties that are measured, the procedures utilised in determining these properties, and their variability under conditions of reproducibility, and to a lesser extent repeatability.

Jan 1, 1997

By D J. Williams, S Islam

Worldwide production of black coal amounts to about 8 billion tonnes. Perhaps 20% of this annual production is washed to improve its quality, generating perhaps 250 million tonnes of coal tailings annually, generally in the form of a slurry. The coal tailings slurry is typically thickened to about 25% solids by mass prior to disposal to a tailings storage facility (TSF), and hence comprise mostly water (about 85% by volume), plus sand, silt and clay-sized mineral particles and carbonaceous material. While the tailings settle and consolidate on deposition in the storage facility, their high moisture content makes them prone to run-out should the tailings dam fail, and makes rehabilitation of the tailings difficult. Hence, it is important to understand the consolidation and shear strength of coal tailings. Laboratory consolidation testing of coal tailings from a slurry to a soil-like state has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. Laboratory vane shear testing of coal tailings produced at different gravimetric moisture contents has also been carried out. The test results have allowed a regression model to be developed relating the peak vane shear strength of the coal tailings to their gravimetric moisture content.CITATION:Islam, S and Williams, D J, 2018. Consolidation and shear strength of coal tailings slurries, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 62–71 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

I take it the character of addresses to conventions, should, following precedent, avoid details, and treat subjects rather from a philosophical point of view so far as they will permit.In the subject about to be treated on, an endeavour will be made to find here we stand as regards the past, in order that we may the better, hope to look correctly in the direction to be followed.It may be assumed that the main object of the Institute is to forward mining interests and the ways in which engineers can aid those interests are many. If all of us were to try to follow many of those interests we should become like" jacks of all trades and masters of none". Mining engineering is consequently subdivided, all are necessary to the common end, and it is on one of those divisions I have undertaken to address you. The subject or steam pumping is a large one, and I regret, not having received such longer notice as would have enabled me to do better justice to the subject, and more respectful regard for yourselves. I must, however, under the circumstances, crave your generous consideration, and hope the topics mentioned may furnish material for discussion and future papers of far more value than this one, Ind.eed, the subject is so illtimately and historically associated with mining that if treated on its merits would be highly interesting or could be made so in more capable hands.

Mining is a high risk industry where miners seek to secure certainty in all of their dealings. The introduction of native title to the Australian legal system with the High CourtÆs 1992 Mabo decision and subsequent Native Title Act 1993 has added to the risks associated with implementation and the ongoing operation of exploration and mining projects. The High CourtÆs Ward case in August 2002 confirmed Crown ownership of minerals and petroleum. But the Court also found that a mining lease that allowed an exclusive possession for mining purposes did not extinguish all native title rights and interests. Although the Court was specifically considering WA mining tenements, the WA mining lease is very similar to the mining leases and licences that exist across Australia, meaning that these tenements are unlikely to fully extinguish native title. The Ward case means that native title remains squarely on the table now and into the future for those involved in developing exploration and mining projects. However, certainty and workability is capable of being secured and this paper discusses some means by which this may be achieved. The paper starts by considering two of the many 1998 amendments to the æfuture actsÆ regime under the Native Title Act, Indigenous Land Use Agreements (ILUAs) and the application of ægood faithÆ negotiation to all negotiating parties. It then looks at native title agreements, other issues affecting negotiations and tips for negotiation technique.

Jan 1, 2003

Iron formation-hosted iron ore deposits account for the majority of current world iron ore production and consist of three classes: unenriched primary iron formation with typically 25 to 45 wt per cent Fe; martite-goethite ore formed by supergene processes, with abundant hydrous iron oxides containing 60 to 63 wt per cent Fe; and high-grade hematite ores thought to be of hypogene or metamorphic origin overprinted by subsequent supergene enrichment with 60 to 68 wt per cent Fe.Individual iron ore deposits range from a few millions of tonnes to over two billion tonnes at >64 wt per cent Fe, although most are within the range of 200 to 500 Mt. In the Hamersley Province of Western Australia, martite-goethite ores are largely developed in the Marra Mamba Iron Formation, although high (>0.08 per cent P) phosphorous mineralisation is also well developed in the stratigraphically higher Brockman Iron Formation. Whilst the vast majority of high-grade microplaty hematite ore is best developed in the Brockman Iron Formation, this paper provides the first textural evidence of locally significant microplaty hematite mineralisation in the Nammuldi Member of the Marra Mamba Iron Formation, in the Chichester Ranges at the Christmas Creek, Cloud Break and Mount Nicholas prospects. Petrographic studies have identified a high-grade Fe texture composed of nanometre scale plates of hematite in mineralised sections of primary microplaty hematite deposits in the Pilbara and elsewhere, well below the normal depth of weathering or dehydration. The population of nanometre to micrometre scale hematite plates is interpreted to represent various stages of nucleation, crystallisation and progressive growth of hematite from the primary ore-forming fluid in areas that were once iron-rich carbonates or silicates in the BIF.

Jan 1, 2005

About 74% of global seismic energy release occurs in the Circum-Pacific zone. Worldwide, about 71% of seismic energy release is in the form of shallow earthquakes, 27% as intermediate, and 2% as deep earthquakes. Seismic energy release is variable in time and has been shown to correlate with the amplitude of the Chandler wobble. It was high during the period 1949 to 1967, and is now at a rather low level, with the latest earthquake over M = 8.0 having taken place in Indonesia in 1971. The average worldwide recurrence rate for the expected largest magnitude earthquake (M "9.5) has been estimated as several tens of years, in marked contrast to the several tens of thousands to hundreds of thousands of years separating the largest volcanic eruptions. Geological studies are needed to establish reliable mean intervals between large earthquakes, and to detect the e;:istence of long-term fluctuations in the ste of occurrence. Seismic gaps have proved seful in static forecasting of large earthquakes, by identifying places where closer study of the variation with time of seismicity, deformation, and other parameters, may lead to the dynamic p_ediction of time, place and magnitude of earthquakes. The model of stress concentration at asperities explains the main features of seismicity in the Circum-Pacific. Slow earthquakes have been detected instrumentally, notably an event immediately preceding the 22 May 1960 Chile earthquake, the largest this century. It seems likely that this type of deformation may explain both instrumentally detected and macroscopically observed pre-seismic deformation, as well as unusual animal behaviour reported before some earthquakes. Seismic and volcanic events are interdependent, with large earthquakes commonly triggering eruptions. Melting of rock and intrusion of magma is likely to accompany many earthquakes.

Jan 1, 1987

By B Hall

In feasibility studies the choice of optimum cut-off grade is typically based on an evaluation of tonnage grade curves and manual design of stopes at one or two cut-off grades. In the industry these stope designs are usually based on break-even cut-off grades, but there is little consensus on what cost and price assumptions ought to be included. A new tool for automated stope design has been developed that generates sets of stope shapes for a nominated range of cut-off grades, or depending on the nature of the mineralisation, cut-off values based on net smelter return calculations in the block model. The stope design procedure includes constraints in stope and pillar geometry for the selected mining method and can be used to evaluate sublevel interval and sensitivities to other design parameters in the specific geological and geotechnical environment. These ænested stopesÆ are analogous to ænested pitsÆ in open cut design, and can be used as a key input in the æhill of valueÆ methodology for the evaluation of the optimum cut-off grade in underground design. The results of many consulting studies indicate that a break-even cut-off grade will not be the optimum cut-off grade. A particular benefit of the new stope design tool is that the design rules used to establish stope shapes in the feasibility study can then be used in mine production, in an optimal and repeatable method. This methodology is being advanced in the AMIRA P884 PRIMO project, which is a new research collaboration coordinated by AMIRA International. The project has brought together active research groups in Australia and Canada, with the goal of developing a flexible framework and set of software tools for optimisation in underground mine design.

Jan 1, 2009

By C McIntosh, M Carder, P M. J Durance

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Disseminated, gold-bearing sulfide minerals hosted in sheared, wall rock metasediments and clay alteration zones comprise one of the dominant styles of Palaeozoic orogenic gold mineralisation within the Reefton Goldfield, and is exemplified by OceanaGold’s Globe Mine. This study begins the exploration and characterisation of the gold-arsenic-antimony mineralisation hosted within the dominant lithologies of the Globe-Progress shear zone. The main gold-bearing sulfides are pyrite, arsenopyrite and stibnite. Pyrite and arsenopyrite are not compositionally uniform across the Globe-Progress shear zone. Pyrite from the mineralised greywacke and argillite has higher As contents than pyrite in the host rock and pug breccia. Furthermore, the mineralised greywacke and argillite pyrite are enriched in As from core to rim. The 3D models based on bulk assays reveal a significant correlation in the distribution of Au, As and Sb. The interpolant for Sb envelops those for Au and As, which in turn are very similar to each other in their vertical and lateral extents across the shear zone. This result is consistent with earlier findings that the occurrence of stibnite represents a separate and likely later phase of mineralisation relative to that represented by the formation of disseminated pyrite and arsenopyrite both of which exert a stronger control on the distribution of As.CITATION:Durance, P M J, Christie, A B, McIntosh, C and Carder, M, 2015. The composition of disseminated, gold-bearing sulfides within the three-dimensional framework of bulk Au, As and Sb in the Globe-Progress orogenic gold deposit, Reefton Goldfield, New Zealand, in Proceedings PACRIM 2015 Congress, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Grigorescu, S Crimp, J H. Hodgkinson, P Kokic, W Jin

Mines are typically located in remote, inhospitable locations and movement of materials between site, processor and port are often at risk from extreme weather events. Mining companies have recorded multiple supply chain, production and logistics delays caused by climatic events. Recent analyses of extreme temperature and rainfall events (90th and 99th percentile values) for 1960 to 1985 and 1986 highlighted regionalised increases in the frequency and intensity of extremes. The trajectory of this change is likely to be maintained (IPCC, 2014) in regions where increases have occurred historically, suggesting that some parts of the industry may be faced with management challenges beyond current experience (Hodgkinson et al, 2010; Loechel, Hodgkinson and Moffat, 2012). Reliance on historical data to plan for extremes (such as scheduling production downtime to reduce impact) will become increasingly ineffective as the data become less representative of future conditions. Importantly, mine site remediation and closure management need to consider the future climate to ensure rehabilitation is sustainable under changing conditions.Vulnerability assessments and risk-reducing adaptation will become more common as the industry reaches to secure both a mine’s longevity and the industry’s reputation as shareholders and clients become less tolerant of repeated or prolonged interruptions (Hodgkinson, Hobday and Pinkard, 2014). Climate-resilient new mines may be planned using site planning tools combined with knowledge of future climate scenarios. Scenario tools are valuable for developing a gated risk management approach to reducing climate-risk during a mine’s life, through to the rehabilitation process and for managing care and maintenance or closed mines.CITATION:Hodgkinson, J H, Crimp, S, Jin, W, Kokic, P and Grigorescu, M, 2016. Life-of-mine planning tools for a changing climate – intuitive, interrogative, iterative, in Proceedings Life-of-Mine 2016 Conference, pp 71–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016