Search Documents

Cable bolts have been used extensively in the development of the footwall of the Mt Whaleback Mine as a part of the ground improvement program since 1986. High tensile seven wire stress relieved steel strand similar to that used in pre-stressed concrete and grouted in place with sulphate resistant cement have been employed for rock-mass reinforcement.Most of the footwall is developed in Mt McRae Shale which contains a 20 m thick pyritic shale layer 14 m below the ore/waste contact. Due to extensive folding of the footwall rocks, the pyritic shale layer regularly occurs on, or close to the pit slope. Rain water run-off seeping through pyritic shale becomes acidic to the extent where its pH value can be as low as 1.5.

Jan 1, 1992

By G R. Hancock, W D. D P Welivitiya

is placed in a waste rock dump, which is usually later reshaped to be erosionally stable, initiate and sustain vegetation and ultimately integrate with the surrounding undisturbed landscape. However, it is unclear how this exhumed material will weather and evolve for most sites. Also, there is a lack of data on the weathering of post-mining materials. If weathering is better understood, then there is the potential to improve rehabilitation outcomes. To improve predictions of the evolution of soil properties and weathering-limited erosion, estimating the rate at which fine, transportable material is produced from the weathering of larger, non-transportable particles and the resultant fragment size distribution and how that distribution evolves over time is necessary. This study examines the weathering process for four different coalmine waste rock materials for a Bowen Basin, Queensland site. Materials obtained from various areas of the coalmine were subjected to cyclic wetting and drying and heating and cooling. Particle size distribution and other material properties were explored after each experimental cycle to ascertain how the material changes during the experimental cycles. The particle size distribution data of wet and dry cycles were used as input data in a numerical weathering model to explore the dynamics of the weathering process for each material sample. A Monte Carlo framework was employed to assess the geometry of the weathering products, weathering rate and the number of daughter particles produced within a weathering cycle. Then the SSSPAM Landscape Evolution Model was used to evaluate the influence of weathering on erosion and landscape evolution of a post mining landform. SSSPAM simulations with: (i) active weathering and (ii) without weathering were run for each material. The erosion rate and the overall landform structure were then compared between weathering and non-weathering simulations.

Aug 2, 2023

By B Arthur, K Sexsmith, D Hockley, S D

At the proposed Crandon Project, mill tailings would be depyritised for upland disposal. The resulting pyrite concentrate would be disposed of in the underground workings as a cement-amended paste backfill. In the long term, the underground workings would be flooded and the potential for the paste backfill to generate acid would be limited. However, while the mine is operational, there is potential for oxygen ingress to the backfill that may lead to sulfide mineral oxidation and acid generation. A series of humidity cell tests were completed to assess the potential for groundwater contamination. To assess effects of surface area on oxidation, the humidity cell tests were conducted on moulded cubes of paste backfill. The tests were terminated at different intervals, and the cubes were dissected and examined mineralogically. Various leach extraction procedures were also used to assess the progress of oxidation and secondary mineralisation within the paste backfill. The test results showed that: the cement amendment significantly contributes to acid neutralisation and results in a lag in excess of one year before the onset of acidic conditions (in comparison to less than three weeks for the pyrite concentrate); the depth of oxidation in the paste backfill is restricted to about 1 mm after 107 weeks of testing; and secondary minerals form a distinct ærindÆ at the surface of the paste backfill. The results indicate that acid generation in the backfilled stopes would be minimal. The importance of including the surface area effect in the testing (ie using moulded cubes) is clearly demonstrated.

Jan 1, 2003

By Walker G. S

Infrared and Raman spectroscopy have been used to study a range of solid state and aqueous solution species which are of interest in extractive metallurgy. In the solid state new Cu(II)/CN'/NH3 complexes have been detected, iron impurities in kaolin characterised, aluminium substitution in hematite and goethite quantified, and the crystallinity and orientation of zircon determined in heterogeneous crystals. In aqueous solution metal cyanide complexes and equilibria were readily characterised, the thermal decomposition of SO2 monitored and products identified, and complexation of AI(III) by hydroxycarboxylates observed. Attempts to monitor the early stages of the gelling of silicate solutions were less successful, with only changes in the gel being detected. However, the degradation of 12-tungstosilicic acid was readily monitored as a function of both time and pH.

Jan 1, 1996

By Grinenko VA

Mineralogical, chemical, and isotopic data have been obtained for samples from 11 volcanoes and 4 kortlandite intrusives on Kamchatka.Similarities and differences in ore-bearing and barren intrusives are discussed. Differences in sulphide mineralization and sulphur isotope compositions of intrusives are explained in terms of the "auto-sulphurization" hypothesis which involves the redox conditions of the host rocks. possible role for carbon in nickle sulphide ore formation is also considered.

Jan 1, 1990

By M Lewis, A Cook

This paper is based on the technology and functionality of a Modular Mining IntelliMINE« system which is a real-time decision-making tool. The IntelliMINE« system, incorporating Dispatch, is a fully Integrated Mine Management System. Measuring, quantifying and analysing the performance of mining is considered a fundamental and strategic step towards changing the nature of technical and operational decision-making at the majority of international mining corporations. Successful implementation of electronic data capture devices and computerised tools have enabled many mining operations to improve their competitive position with an improvement in the utilisation of the key assets, mineral resources, capital mining equipment and human resources. Real Time Mine Management Systems are designed to direct the emphasis away from collecting data and focus decision makers on the real issues with well-presented and reliable information. The systems provide a common stream of information to enable senior management, operations, maintenance, technical and process plant staff to make complementary decisions based on reliable, accurate and timely data. The mine asset information tools focus all employees on performance and give them feedback on their area of responsibility. The resulting tangible benefits can be delivered in different forms depending on the mining method, ore type, workplace culture and the current competitive position. Typical areas of improvement reported by system users are:reduction in capital expenditure on mining equipment fleets; more effective planning and budgeting parameters and procedures; increased control over ore-extraction and processing; increased employee accountability and organisational performance; and improved co-ordination between planning, operations, maintenance and processing. These improvements can be delivered in different forms depending on the status of the mine and commodity markets. In times of market oversupply and low commodity prices, the benefits can be delivered to the bottom line in terms of reduced cash costs, reduced capital and operating resources to maintain constant production. In times of market expansion, existing capital resources will be more productive delivering increased production and revenue. Mine management systems have the potential to transform a traditional mine operation into a learning organisation with an improved understanding of the critical performance issues and enable development of relevant strategies to continually identify and eliminate operational inefficiencies. The effectiveness of each strategy and operational change can be accurately monitored and its success (or otherwise) will be quantified. The latest downturn in the world metal prices has forced many mining companies to focus on cost reduction and productivity improvements as a means of remaining competitive. Maintenance represents a significant proportion of the overall operating costs in the mining industry. A structured proactive maintenance approach such as Reliability Centered Maintenance (RCM) can achieve significant cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled, thereby reducing costs and interruptions to production.

Jan 1, 2000

In this year marking the centennial of the Geological survey of Western Australia, it is appropriate that we should review the value of the contribution of the Survey, and Australian Geological Surveys in general, to the exploration industry. Most geological surveys in Europe and North America had their origins in the first half of the 19th Century when the burgeoning Industrial Revolution was demanding the identification of new sources of coal and iron ore. Australia, as a young nation, essentially dependent on an agricultural and pastoral industry, and with already discovered vast coal resources in Eastern Australia, had, no great need to explore for new mineral resources. However, with the discovery of gold in 1851, the mineral potential of the country became apparent to the whole world and the first Geological Survey in Australia was set up in 1852 in Victoria under A.R.C. Selwyn. After a number of false starts all Australian States had an established Geological Survey by 1900. It is hard to assess the contemporary value of the early work of the Geological Surveys with respect to exploration, almost all major mineral discoveries were made by prospectors and most mining companies had little time for geologists - although the Chamber of Mines in Western Australia in 1910, did recommend that the Geological survey be granted an additional ten thousand pounds over two years to map all existing goldfields and the country between them, and produce a reconnaissance map of the area east of a line between Wiluna and Edjudina as far as the South Australian border!

Jan 1, 1988

An integrated computer system (the Short Term Mine Management System) has recently been developed by B.H.P. Steel Long Products Division in Whyalla, South Australia for use in their open pit iron ore mines.The system incorporates blast design, comprehensive blasthole data handling, grade coilrol, stockpile scheduling and management and reconciliation within a single, user friendly computer package. The blast design system allows the blasting engineer to design the layout of holes for a production blast using geological information projected from the bench above to aid in appropriate blasthole positioniog in particular rock types. The grade control system allows mining blocks to be designed and evaluated from blasthole information using interactive graphics processes. The handling, storage and reporting of blasthole survey, assay and geological logging data forms an integral part of this system. Stockpiles can be constructed from a number of mining blocks to reach a specified target grade using the stockpile management system. Although not yet integrated, the reconciliation system will reconcile stockpiles back to mining blocks and to the geological model.

Jan 1, 1990

By Forssberg KSE

The behaviour of cationic and anionic collector mixtures in the feldspar-quartz flotation system has been investigated througl conductivity, surface tension, zeta-potential and flotation studies. Tht results show the formation of molecular complexes between oppositel; charged collector ions through charge neutralisation. The molecular complexes are found to have a higher surface activity than the individua components. The mole ratio of the mixed composition is found to have, significant effect on flotation. Mole ratio less than unit} (anionic/cationic) of collector mixtures increases the flotation recoveries If the mole fraction of the anionic collector is greater than the moh fraction of cationic collector in a mixed composition, flotation ceases The flotation selectivity principally depends on the inherent differences it the surface charges of feldspar and quartz at the flotation pH values of

Jan 1, 1993

Applications of chlorine metallurgy to the extraction of metals often result in the production of volatile metallic chlorides, most of which condense directly to a solid phase at 1 atm pressure. A stirred-bed condenser suitable for the recovery of these materials is described.The unit, developed from the concept of a fluid bed condenser, has the advantages of versatility of operation and ability to control fog and dust formation. Test work using aluminium chloride vapour (as an example of a volatile chloride) gave recoveries approaching 100 per cent. The yield was dependent upon halide content of the vapour, flowrate, and, to a lesser extent, upon coolant temperature. Analysis of the heat transfer dataindicated condensation side coefficients in the range 10 to 30 B.T.U./hr sq. ft. 0p.

Jan 1, 1971

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004

By Sergeant G. D, Norman J. R

The importance of reducing the moisture content of fine coal, the nature of the retained water and the means of its removal are discussed. A statistical technique, using a balanced block design, was used to isolate the significant factors determining water content of a coal filter cake, The most significant factor was particle size distribution. A simplex evolutionary operation (evop) was used to determine the optimal quantities of additives required to produce the lowest moisture content for a selected coal size. For this optimum condition (18.6 lb xÇ20 per 100 lb dry coal), additions of 0.045 lb magnesium ion, 0.0026 lb separan A.P. 30, and 0.098 lb aerosol O.T., per 100 lb dry coal were required. The work illustrated the uses of statistical evop technique for the determination of optimal conditions in industrial research projects.

Jan 1, 1969

By T McConachy

New opportunities for miners are beginning to appear through new discoveries, improved knowledge and access to vast unexplored areas of the deep sea and continental shelf. Recent discoveries of undersea hydrothermal deposits show evidence of high-grade mineralisation, although in many instances the extent of the resource is still unknown. The promise and the difficulties of undersea mining have been evident since attempts were first made to mine manganese nodules in the 1960s. The physical nature of the undersea resource is a key influence on its mining potential; and environmental issues will also become increasingly important. This paper explores these issues and concludes with a description of the immediate to medium term applied research required to develop this industry and the spin off that such research can provide.

Jan 1, 2000

By Gupta A, Hall ST

The grinding characteristics of quartz which is normally associated with gold bearing ores in Kalgoorlie area was examined in a stainless steel laboratory size ball-mill in the presence of inorganic and organic surface active reagents. The cationic species considered were Fe3+, Cu2+ and Ca2+, and the anions were CO? and S2 as these are normally present during the process of grinding of gold ores in the region. The organic surfactants examined were K-amyl- xanthate, dodecylamine-hydrochloride and the Grinding Aid XFS-4272 manufactured by Dow Chemical The study was primarily based on an examination of the electrokinetic properties of quartz surface in the presence of the grinding reagents. Zeta potential at different reagent additions and pH values in the presence of individual reagents were examined and the corresponding grinding charcteristics determined. A correlation has been indicated between the grinding characteristics, as measured by the -53um size fraction produced, and the surface energy of quartz. It was observed that an

Jan 1, 1978

By Dudgeon RN, Houston ML

When the original Mount Gunson joint venture,between CSR Limited and United Uranium N.L. ceased operations in December 1971, an intensive exploration campaign was launched to prospect for more ore in the Mount Gunson region. This campaign resulted in the dis- covery'of the Cattle Grid copper deposit. A comprehensive sampling pro- gramme including the sinking of over 200 diamond drill holes and two vertical shafts,proved the existence of 4.6 million tonnes of ore, at a mean grade of 2.4% Cu,calculated at 1.00% Cu cutoff.

Jan 1, 1975

By Muir D. M

Highly saline process water has a number of implications for the CIP process during the leaching, adsorption and recovery of gold. The reduced oxygen solubility in saline water can seriously reduce the rate of gold leaching, while dissolved oxygen meters do not necessarily reveal actual oxygen concentrations in saline water. High levels of magnesium in the ground water necessitate operation at lower pH (-9), with the potential for greater cyanide loss via HCN stripping. In addition increasing salinity renders viscosity modifiers largely ineffective.The adsorption capacity of aurocyanide onto activated carbon is improved with increasing salinity, but misleading results can be obtained in assessment of gold loading kinetics of plant carbon samples already loaded, or partially loaded, in saline water if subsequently tested in fresh water. Elevated chloride levels in the Zadra elution process can cause severe anode corrosion in the elecuowinning cell. The Anglo elution process is tolerant to only slight increases in water salinity, but elution times can be reduced by ethanol addition. Care is required in carbon regeneration, as salts can catalyse carbon decomposition as well as increase kiln corrosion.

Jan 1, 1994

By Nightingale RJ

A column (50 cm 4) provided with a bell charging mechanism and a rectangular perspex insert was used to investigate the inter-relationship between charging pattern, size analysis and velocity profile for a number of charging methods. It is shown that a strong correspondence exists between size distribution and velocity profile for bell charged ore and coke and that decreased coke volumes cause higher pressure drops and increased central flow in beds with "V" shaped layers. It is also shown that a bell charged mixed burden exhibits greater segregation than when it is bell charged as layers and that when uniformly charged the mixed burden shows least segregation and a virtually flat velocity profile. A relationship is derived for "V" profile charges showing the extent of central segregation with furnace size.

Jan 1, 1975

By Segnit ER, Jensen G

The decoppering of soft and hard leads was investigated by stirring in an open pot, using sulfur or sulfur plus pyrites, or sulfur plus pyrrhotite, as reagents. Lead samples taken during the process were analysed for copper. Dross samples were examined by optical micro- scope, SEM and XRD. Soft lead containing silver can be decoppered satisfactorily by stirring with 0.1% S at low temperatures - close to 330¦C. Soft lead, whether containing silver or not, can be decoppered satisfactorily at higher temperatures by stirring with 0.1% S plus 0.4% pyrites. Then CuFeS2, Cu5FeS4 and PbS are formed, instead of Cu2S, CuS and PbS when using S alone. Hard lead containing tin can be decoppered satisfactorily by stirring with 0.1% S at temperatures from 320-400¦C. When stirring with 0.1% S plus 0.4% pyrites, reversion of copper from dross to lead on prolonged stirring does not occur. Hard lead without tin can be decoppered with S plus pyrites better than with S alone, but the presence of antimony hinders the decoppering, which is less effective on lead with 5.5% Sb than with 2.3% Sb.

Jan 1, 1980

The paper describes the studies conducted to date on the short term adsorption/desorption of gases in coal from the point of view of developing techniques to predict imminent outbursting conditions in coal mines. A number of different parameters such as'dP express, K' and AV 0/60 etc. which have been effectively used overseas were studied on samples of coal from Westcliff and Leichhardt Colliery. Results indicate that these do not seem to be valid indices for predicting an outbursting condition. Based upon desorption isotherms, a new index defined as "L" has been developed which shows promising results. This index is in a position to differentiate the changes in the structures of coal and its proness to outbursts. The "LZ value determinations and its usefulness opens a new field where it would be possible to determine outbursting conditions from existing drill cores obtained during exploration studies or from long holes drilled in advance from underground workings. The index is more or less independent of the time elapsed between the extraction of a sample and the conduct of the test. The test for "L" can be conducted'on site or in the laboratory. The test is simple, easy to carry out and the "L" value for a sample can be calculated in less than 20 minutes. It could be adapted as a routine test for monitoring outburst conditions in mines.

Jan 1, 1980

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990