Search Documents

By Fiedler VA, Threadingham GM, Leckenby DF, Clarkson CJ

The Utah Development Company Research and Development Laboratory has embarked upon a programme of optimisation of the company's coal preparation plants. This goal is being accomplished in a three-fold manner - use of pilot plant equipment for optimisation and modelling of the various unit operations, evaluation or development of on-stream ash analysis for process control, and evaluation or development of alternative processes. In each of these areas, digital data acquisition- and at a later stage, process control feedback, is being extensively utilised, based largely upon the use of the HP85 and HP9915 desktop computers. A variety of input/output configurations such as HPIB, BCD, GPIO are used, and at times supplemented by microprocessors such as the Intel 80/05 to assist in data transfer. This paper will discuss a number of specific projects, especially in relation to the manner in which the variables are monitored, and the data later retrieved and analysed.

Jan 1, 1983

The paper considers the nature of outbursts of coal and firedamp as they occur. t follows the development of methods of working used to try and induce outbursts safely under controlled conditions and details the life support systems used to provide maximum rotection to persons who may be affected by s_lontaneous outbursts. Tilt: NATURE OF OUTBURSTS IN THE UNITED KINGDOM .1y some areas in the coalfields of the ingdom are affected by outbursts of :hal and firedamp. The main area affected is he western end of the Anthracite coalfield r: West Wales. In this area 206 outbursts .eve been recorded resulting in the loss of 8 lives. Anthracite is a high rank coal produced v the geological effects of age, depth and ynamic metamorphism. Outbursts have been xperienced over a wide area of the anthracite field but have been most frequent, and most evere, in the areas where carbon content is its highest and where the coal measures cave been subjected to the highest degree of eulting and overthrusting. Most outbursts ire associated with geological abnormalities ,:id the coal ejected during outbursts is sually of a soft and powdery nature.

Jan 1, 1980

By Flierman GA, Van Toor CH

Investigations were carried out of burden distribution using a full scale model of the furnace top. Various charging sequences were used and large differences were found between ore charged as sinter-pellets and as pellets-sinter. These were attributed to the differences in the angle of repose between the two materials. Permeability index was defined which was independent of the driving rate from which a furnace resistance index was obtained for use in weekly reports. Results are summarised as a single expression between blast rates and pressures and the values of Qbl and Qmax are continuously measured to aid the operators in controlling the wind rate in the safe AP region. Results also indicate a reserve in capacity of No. 7 BF.

Jan 1, 1975

Buoyant levels of world economic growth and recovery in intensity of metals usage suggest that demand for minerals will remain relatively strong into the 1990's. Supply constraints, low stock to use ratios, financial and political factors imply lower elasticities of supply for minerals in the future. The outlook for minerals and metals prices from a pro-ducers viewpoint is, accordingly, promising.The recent recovery in world minerals prices, following strong growth in the world economy over the last few years, makes it appropriate to consider the structural forces at work in the formation of world demand and supply of minerals. This paper will review past trends and consider some of the main economic issues facing the mining industry in the 1990's.

Jan 1, 1990

By Kuipers A. J

Aberfoyle has been applying computer methods to mine geology in small to medium-sized underground mines since the early 1980's. Recently, the installation of DATAMINE software at the Hellyer Mine in Tasmania has allowed development of computerised applications which assist both mine geologists and mine planning engineers on a daily basis.Comprehensive data is entered into a database prior to survey coordinating to produce a processed database which can be accessed for construction of a variety of plots. The folded and faulted nature of the orebody contacts at Hellyer has necessitated the use of the structure contour method to provide a complete 3-D spatial interpretation. Computer-generated contact intersection points are hand-contoured before digitising and wireframing as a digital terrain model. This wireframe model can be sectioned in any plane for mine planning.

Jan 1, 1990

In recent years new instrumentation and digital technology have Wrote possible a new facet of goo-physics: broadband seismology. From digitally record-ing networks and arrays. broadband scistnograrns of body waves that are flat to displacement and veloc-ity in at least the frequency range from 0.01 to 5.0 liz can now be routinely obtained for most carthquakes of magnitude greater than about 5.5. In contrast to data from conventional narrowband seismographs, broad-band body waves have sufficient spectral information to nvest,igate the many frequency-dependent eflects that may arise from source finiteness and from wave prop-agat ion phenomenon. Besides the usual parameters of depth. moment and focal mechanism, broadband data have sufficient spectral information to provide estimates of radiated energy, associated stresses and the frequency dependence of source parameters. Moreover. teleseis-mically recorded broadband data and near-field strong motion accelerograms overlap in the frequency band be-tween about 0.1-2.0 Hz. Thus. v it h broadband data it is possible to connect far field and near field data in order to make estimates of acceleration for almost any seismically active region of the circum-Pacific.

Jan 1, 1990

By Lyman GJ

Systems for the routine on-line determination of ash content of process streams in coal preparation plants and handling systems have been in use in Australia for over four years. More recently, monitors for on-line moisture measurement have been developed to complement the ash measurement function. The technology for these systems is reviewed briefly. The development of reliable ash and moisture monitors has made the implementation of automatic systems of coal quality control practical. The emerging philosophies of automatic control in Australian preparation plants are examined with particular emphasis on systems involving dense medium circuit regulation. Related developments in flotation control and coal sorting are noted to complete this overview.

Jan 1, 1987

LESLIE BRADFORD GOLDEN JUBILEE ORATION "Not only a metallurgist but a scientist of the highest order" Leslie Bradford and the Australian Metallurgical Industry

Jan 1, 1987

By Nichol R

- PART A The Hoppers Crossing Pumping Station is one of the principal components of the Western Trunk Sewer Project which replaces the 90 year old Main Outfall Sewer and will convey 60% of Melbourne's sewage flow from Brooklyn to the Board's Farm at

Jan 1, 1987

By P G. Gaylard

P754 has been an unusual project in that its main aim was to develop a code of practice for metal accounting with the following key objectives:Development leading to an agreed industry standard at corporate governance level Significant improvement of the credibility of metal accounting from deposit to saleable product Development of guidelines for data collection, data analysis, reporting and audit A data analysis toolbox which provides go/no go testing for metal balance data Promotion of industry adoption of these guidelines to improve transparency and financial credibility. Over time, these guidelines may evolve into a code and eventually into a standard Develop and train engineers to become expert in metal balancing and reporting. Papers like this one and the workshop which follows this conference are part of promoting the code for adoption by industry. Developing a code of practice has traditionally been the provenance of professional bodies associated with particular industries û often on a voluntary basis. Given todayÆs industry pressures, it was felt that funding key input might accelerate the development process as well as offer opportunities to research some of the problems and to train some post graduate students in a difficult discipline. In fact, the project has brought together six industry sponsors from a wide range of process types, three research providers, and funded students in South Africa and Australia. The project has also attracted input from the financial community. A textbook to support the application of the code has also been written. The industry sponsors have made the Code and Guidelines available on request to help to facilitate its use by the mineral industry beyond the sponsor group. The Code and Guidelines have already been translated into Spanish and Portuguese which suggests that industry acceptance may happen quite quickly. The main thrust of the code is to integrate commercial and technical performance to a much higher degree. The Check in-Check out (CI-CO) method has been chosen as the vehicle for this combined approach. The mass and metal values used for CI-CO are 'absolute' and provide the basis of financial transfers. The CI-CO process occurs at each transfer of custody - whether between divisions within a company, or between companies. This approach means that measurement of mass and metal flows becomes the critical element of the process and that a quantitative knowledge of measurement accuracy and precision is also essential. This knowledge allows technical differentiation between differences which are within the expected margin of variation and those which must be formally identified as discrepancies and subject to a process of investigation and sign off. Hence, the application of the code for most companies should be more evolutionary than revolutionary, but with substantially more emphasis on measurement and definition of measurement error. Where this can be achieved, it should bring the mineral industry more into line with other industries competing for investment funds, community acceptance and future employees.

Jan 1, 2008

By Laajalehto K

The basic condition necessary for flotation is hydrophobicity of the surface of the mineral to be floated. For sulphides, this condition usually requires treatment with a collector solution. The conditions for this treatment have until recently usually been chosen by the trial and error principle which has indeed been working relatively well under favourable conditions; ie for simple homogeneous ores. However, the present tendency to increasing use of complex and often relatively lean ores sets increasing requirements for the control of the flotation process. This development is the reason for the present rapid development of process control methods in flotation. In addition to the already well-established practices of pH and reagent feed controls, the importance of measuring and controlling the electrochemical potential of the ore particles to be floated is recognised in the case of sufficiently conductive minerals. In fact, the electrochemical potential seems to be the basic quantity determining the flotation behaviour of such relatively well-conducting minerals as sulphides. Since the hydrophobicity of the mineral and, hence, its flotation properties are ultimately determined by the composition and structure of its surface, information on these under different process conditions is important for design and operation of efficient flotation processes. The basic requirement set for the methods used for obtaining this information is high surface sensitivity of the method. The recent rapid development of surface characterisation has produced several methods which fulfil this requirement. Their application to the problem of characterising surfaces of mineral samples in contact with collector solution is, however, often complicated. The main reason for this is the vacuum environment necessary for the measurement. In the case of flotation experiments this means that in most of these methods the measurement cannot be made in situ, but the sample must be extracted from the liquid and subsequently evacuated in the vacuum chamber of the instrument. It is essential to carry out these steps so as to avoid to the extent possible changes in the sample surface. For the purpose of establishing whether this has been accomplished it is important to compare the results of methods operating in vacuum with some available in situ method. An optimal choice of methods seems therefore to be a combination of the available powerful vacuum methods with in situ measurements. The most usual combination seems to be X-ray photoelectron spectroscopy (XPS or ESCA), Fourier transform infrared spectroscopy (FTIR) and electrochemical measurements. This choice combines the unique possibilities for direct elemental and chemical characterisation offered by XPS (Cecile, 1985) with the in situ capability of FTIR and electrochemistry. In the XPS measurements, it is essential to apply a special sample handling technique to avoid loss or damage of some sensitive species of the collector-based layer on the mineral surface. In the following will be given some examples of the application of the XPS technique in combination with electrochemical methods of sample treatment to studies of the layer formed on sulphide substrates in ethyl xanthate (EX)

Jan 1, 1993

By Favreau RF

Over the last 20 years the blasting industry has progressed from the stage of being artform to a science as it is today. The use of computers to simulate blasting results has allowed blasting engineers to accurately pre- dict blast results and to optimise their blasting. This paper describes the computer blast simulator called BLASPA and its various applications in blasting. BLASPA allows the blasting engineer to predict blast results given known details of explosive properties, their distribution, rock type and properties, hole size, burden, spacing, collar and subdrill. The simulator runs mathematical situations and outputs numerical estimates of fragmentation and muckpile results. The paper discusses results which show that the mathematical outputs correlate very closely with actual results seen in the field, thus confirming the validity of the simulator. BLASPA can be used to help improve blast design by predicting stress levels in the rock mass and consequent rock breakage.

Jan 1, 1986

The results of about 30 years of exploration and mining activities and research studies in the Kambalda mining district, Western Australia, have led to general agreement that the komatiite-associated Ni sulphide ores formed as a result of igneous processes (Ross, 1974; Ross and Hopkins, 1975; Gresham and Loftus-Hills, 1981; Cowden, 1988; Lesher, 1989 and many others). Despite this agreement, the controls on sulphide supersaturation and concentration of the resulting sulphide in a limited zone, remain uncertain and controversial. A major uncertainty is the source of sulphur in the ore deposits. Two principal sulphur sources have been proposed: 1. komatiite lava/magma (Hudson, 1972; Naldrett, 1973; Lesher et al, 1981; Cowden, 1988; Foster et at, 1995), and 2. sedimentary material (Groves, Barrett and McQueen, 1979; Lesher, Arndt and Groves, 1984; Lesher, 1989; Lesher and Campbell, 1993). Resolution of the uncertainty regarding the sulphur source is required for a complete understanding of the controls on ore formation, which in turn would significantly impact exploration strategies in the Kambalda mining district and elsewhere. This paper reviews the constraints on sulphur sources for the komatiite-associated Ni sulphide ores in the Kambalda mining district. The focus is on the general characteristics of the ores and surrounding rocks: individual ore deposits are not described, though specific examples are noted where appropriate. The stratigraphic and volcanic settings and geochemical (major and trace element and isotopic compositions) characteristics of the ore deposits and surrounding rocks are considered within the context of the competing sulphur source models, and future directions of research in the district are noted.

Jan 1, 1996

By Greenwood AG

Research into cemented rock fill at Mount Isa Mines Limited since 1992 is described. The key mechanisms controlling segregation during stope filling with cemented rock fill are described and include the gravity flow mechanism which is described in detail. Examples are provided to demonstrate these mechanisms. Comparisons are made between Mount Isa Mines' cemented rock fill and slurry-based cemented rock fills. Recent backfill stability modelling using a three-dimensional finite clement program is described.

Jan 1, 1998

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Aziz NI, Guo H

Most of the existing models of the mechanisms of drilling and cutting processes are oversimplified in both stress state and failure criterion. On the other hand numerical modelling techniques are a more versatile method with great potential for development. In reviewing drillability and predicting performance of excavation machines the empirical tests, which simulate the physical breakage action in excavating processes are seen to be the best in terms of penetration rate predictability. Future methods of determination of drillability should concern the breakage characteristics and rock abrasivity involved in the two basic types of attack, i.e., percussive and rotary drilling.

Jan 1, 1988

By Jones J. P, Arriagada J, Scherpenisse C. R

A recently-developed model is used as a tool to optimise the design of blasts used to create final walls in large open pit mines. The use of this tool has allowed present blasting practice and proposed designs to be evaluated to predict the likely extent of rock damage behind the final wall. The evaluation of the damage is dependent on the predominant local geology. Modelling of damage using the software allows the potential zones of rock damage to be evaluated under the following criteria: I . the extent of new fractures formed in the intact rock mass; and 2. the distance to which dilation and extension of existing discontinuities and pre-existing fractures will likely occur. The computer model has been used to examine present blasting practice and to estimate the damage induced by final and intermediate rows of blastholes. The results of current practices are presented in a visual form that allows simple comparisons to be made for any proposed changes in design. To confirm the predictions of the modelling, physical measurements are being undertaken at selected mines to quantify damage behind blast patterns, and experimental programs are underway to measure near-field vibration, or shock, levels. The computer modelling software is being used to qualify and improve the design of final rock slopes in large surface mining excavations, and to provide site engineers with well-defined design criteria for consistency in design. The model is seen to be just one of many tools which are being used in large open cut mining operations to gain an improved understanding of blasting and blast control.

Jan 1, 1995

Gold mineralization like other low concentration high value commodities has gained the notoriety of being difficult to sample. This adversely affects the confidence that can be placed in resource estimates and ore reserves. As an example, it is not uncommon to find differences of the order of 30% between duplicates of a single sample sent to two different commercial laborartories. Two halves of drill core generally show marked differences in grade. Again differences of 50% are not uncommon in halved core. In the context of this type of "error" within the base data used for the resource estimate, many of the subtleties of computation methods and expert judgement of resource categories, are almost a case of shutting the gate after the horse has bolted. Managers, financiers and consultants must question the quality of the base data upon which resource estimates are made. They must insist that standard and duplicate samples are used to measure the accuracy and precision of commercial analytical laboratories, that sampling practices have been checked for possible bias and give tolerable repeatability. Further they must ensure there can be a realistic confidence in the estimates by correctly using these measures of data quality to quantify risk.

Jan 1, 1990

Laboratory high tension roll separation and the commercial machines available for this purpose are discussed. The shortcomings of these machines are indicated and a machine that overcomes some of these undesirable character- istics is described. A procedure for evaluating laboratory high tension roll separation is described. The use of this evaluation procedure in conjunction with the laboratory separation is described with examples taken from the Dunwich and Hexham processing plants of Associated Minerals Consolidated Limited. Evidence that laboratory testwork results may be directly transposed to operating plants is given. A discussion of the effects of variables in high tension roll separation of mineral sand concentrates concludes the paper, and uses in support results obtained in the metallurgical laboratories of Associated Minerals Consolidated Limited, Southport, Queensland.

Jan 1, 1972

1880 - 1930 - The Golden Years of Mineral Processing Technology

Sep 13, 2010