Search Documents

By C Wu, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Halasu porphyry copper belt, located in the East Junggar basin bounded by Chinese Altay to the north and the Tianshan mountains to the south in the Central Asian Orogenic Belt, is one of the major porphyry copper belts in Xinjiang province, north-west China. Combined with previous studies in this area, the magmatism can be divided into three periods: pre-mineralisation activity of 390 Ma syn-mineralisation activity of 380–370 Ma post-mineralisation activity of 360–330 Ma.Through the comparison of zircon chemistry from ore-bearing and barren syn-mineralisation intrusions, negative correlation was identified between Ti-in-zircon temperatures and oxygen fugacity, corresponding to the fact that late-stage syn-mineralisation granitoids contain high water content, high oxygen fugacity and low temperatures with higher mineralisation potential. In addition, the relative low initial 87Sr/86Sr ratios, high eHf(t) and eNd(t) values and mantle Pb isotope characteristics in this study support that the magma forming these intrusions was probably derived from juvenile crust generated during subduction-accretionary processes.CITATION:Wu, C and Chen, H, 2015. Zircon trace elements and Sr-Nd-Pb-Hf isotope systematic of the Halasu porphyry Cu belt, north-east Xinjiang, China, in Proceedings PACRIM 2015 Congress, pp 637–640 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

In 1939 at the annual meeting of the Australasian Association for the Advancement of Science, held at Canberra, a paper was contributed by E. de C: Clarke and H. A. Ellist in which a plea was made for more "facts" concerning metasomatism near ore-bodies in Western Australia. From time to time writers here, and in other parts of the world, have discussed the alterations in wall rocks of various reefs and lodes, but little has yet been attempted in the matter of accumulation of quantitative data, both chemical and mineralogical, and in the correlation and comparative study of this data. Such a detailed comparative study is needed to determine the economic value of a practical application of our accumulated knowledge of the phenomena of metasomatism.When in 1939 the opportunity offered for an examination of the core from 4 bores recently put down by the Big Bell Mines Ltd., to explore the ore-body of the Corinthian G.M. 10 miles N.W. of Southern Cross, Western Australia it was hoped that some small beginnings might be made of an accumulation of comparative and quantitative data regarding the metasomatism of the wall rock immediately adjacent to this ore-body.By the courtesy of the Big Bell Mines Ltd., the core from the 4 bores was delivered to Survey Headquarters, Perth;in the middle of June, 1939 and copies of assay plans of part of the underground workings at Corinthian, and of the results of assays of the bore cores, were also supplied by the management of the above company.It was not, however, until March, 1940, that it was 'found possible to investigate the core. At that time the writer's colleague, Mr. R. S. Matheson, conducted a: megascopic examination of all the bores and selected material from two of these for possible future chemical analyses. Late in 1940 the writer commenced a microscopic petrological examination of this material.AIM OF THE INVESTIGATIONThe object of the petrological part of this investigation was to determine whether from a megascopic and microscopic examination of the core, any evidence could be obtained indicating changes, in mineralogical composition...

Jan 1, 1942

By A McEwan, J Masters, C A. Jackson, A Catanzano, V Sharp, M Millen, S Rainey, S J. Spencer, G Roberts

A passive acoustic emission (AE) monitoring system has been developed and trialled on two M10000 IsaMillsTM. The analyser detects AE stress waves generated by grinding media impacts with the mill liner during mill operation. Locally propagating stress waves can be detected on the exterior liner surface using strategically mounted broadband accelerometers.The analyser has been developed into a robust commercial prototype system, and has been designed, installed and commissioned with Xstrata Technology at two mineral processing plants.A six-month field trial showed large-scale variation in AE power signature with process conditions. Analysis of the enveloped AE power output demonstrated a strong correlation with mill process conditions – more specifically grinding media relative loading, feed pulp density, feed volumetric flow rate and feed type.Placement of accelerometers along the length of the mill body provided key information on the grinding media relative deportment. The enveloped AE power detected by the mill body, discharge pipe and bearing housing sensors all captured information strongly correlated with mill operating parameters and process state.The prototype analyser demonstrates suitability as a long-term online tool for stirred mill performance monitoring, and potentially for optimisation and control, in beneficiation plants.CITATION:Jackson, C A, Spencer, S J, Masters, J, Sharp, V, McEwan, A, Rainey, S, Catanzano, A, Roberts, G and Millen, M, 2014. Monitoring of M10000 IsaMill™ process performance by passive acoustic emissions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K J. Grohs

Martabe gold and silver mine is situated in northern Sumatra and comprises several deposits in steep terrain that are required to be developed in the optimal sequence for the best possible Net Present Value (NPV) return on the project. In addition, the waste from the excavations is a by-product to be scheduled and used for construction of the tailings storage facility (TSF). These plans need to be aligned to ensure the tailings can be contained relative to the production rate. The TSF embankment construction includes potentially acid forming (PAF) waste that needs to be progressively sealed and rehabilitated to meet the closure requirements of the future.The mine is situated approximately 3 kilometres north of the township of Batangtoru in a seismically active zone between the off-shore subduction zone and the trans Sumatran fault. The mining operation currently includes two open cut pits with a third in development stage, an integrated TSF and dualpurpose valley-fill type waste rock storage facility (WRSF) and TSF embankment. Mine waste is used in construction of the WRSF / TSF embankment, including PAF waste rock, which needs to be scheduled for optimal use in construction activities in a manner that mitigates future acidic and metalliferous drainage (AMD) risks (Pearce and O’Kane, 2017).The Life-of-Mine (LOM) plans must satisfy both optimal pit development to maximise NPV and suitable delivery of waste for effective TSF construction matching the rate of rise of tailings, and consider AMD management, progressive rehabilitation and ultimately effective sustainable mine closure. This paper outlines the methodology to optimise the system to deliver these potentially opposing objectives.CITATION:Grohs, K J, 2018. Martabe integrated life-of-mine optimisation, in Proceedings Life-of-Mine 2018, pp 83–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By N L. Turner, D J. Robinson, A J. McFarlane, N M. Chapman, L L. Kuhar, R L. Meakin, R Martin

A number of geometallurgical tests have been developed within the AMIRA P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project, an interdisciplinary collaborative research project involving four research groups and over 20 global mineral companies. Researchers at the Commonwealth Scientific and Industrial Research Organisation (CSIRO) have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. One of the focus areas has been the development of a leaching scheme for determination of the mineralogical deportment of copper in a large number of samples for geometallurgical applications.Various leaching schemes have been used over the last 20 years to identify the mineralogical deportment of copper. Typically, weak sulfuric acid and cyanide are used to target copper oxides and æsecondaryÆ copper sulfide minerals, covellite, chalcocite and bornite, respectively. Residual copper is assigned to chalcopyrite and/or bornite. Adaptations of this scheme have included the use of a weak organic acid to target oxides or ferric sulfate to target secondary copper sulfides. Testing of the weak acid/cyanide scheme in the GeMIII project using head and residue QEMSCAN mineralogical data analysed with a statistically reliable comparison method indicated that the inferred mineralogical deportment from various leaches could differ markedly from the theoretical or assumed value. Based on this initial work, test development and leach tests on samples from multiple sites has resulted in the development of a scheme to target copper oxides, chalcocite, covellite, bornite and chalcopyrite. This paper presents results from leach tests conducted on a large sample suite from two pits in a Cu-Au ore deposit with results calibrated using mineral liberation analyser (MLA) mineralogical analysis. This study has assisted in the development of a protocol for determining the mineralogical deportment of copper in a large number of samples for geometallurgical applications.CITATION:Kuhar, L L, McFarlane, A J, Chapman, N M, Meakin, R L, Martin, R, Turner, N L and Robinson, D J, 2013. Calibration and testing of a geometallurgical leaching protocol for determining copper mineralogical deportment, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 177-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By P N. Nkrumah, A van der Ent, G Echevarria, P D. Erskine

Nickel phytomining is a low cost alternative to traditional nickel mining and a complementary process to existing mining operations in areas with low-grade nickel soils or nickel waste material. The process of nickel phytomining consists of growing selected hyperaccumulator plant species (‘metal crops’) on Ni-rich (ultramafic) soils, followed by harvesting and incineration of the biomass to produce a ‘bio-ore’ from which Ni salts or Ni metal may be recovered (Chaney et al, 2007). The ‘metal crops’ are selected on the basis of high biomass yield combined with high Ni concentrations (>1 per cent) in the above-ground biomass (Chaney et al, 2007). Currently, Alyssum murale and A. corsicum have been used for Ni phytomining trials, mainly undertaken in Albania and USA (Bani et al, 2015; Li et al, 2003), while the agronomy of <10 species has been tested in temperate regions (Nkrumah et al, 2016). Nickel phytomining has high economic potential; however, large-scale demonstrations are needed to provide ‘real-life’ evidence for commercial operations (van der Ent et al, 2015). Unrealised opportunities exist in tropical regions for commercial scale Ni phytomining. To date, the agronomy of tropical ‘metal crops’ has not been tested. This extended abstract presents the progress of tropical phytomining, and reports on agronomic trials undertaken to determine whether the trends in temperate regions could be confirmed in a wet tropical environment.CITATION:Nkrumah, P N, Erskine, P D, Echevarria, G and van der Ent, A, 2016. Progress in tropical nickel phytomining, in Proceedings Life-of-Mine 2016 Conference, pp 135–137 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R Badreddine, J Rose, L De Windt, P Chaurand, L Raimbault

Municipal solid waste of incineration (MSWI) bottom ashes are recycled as aggregates in civil engineering. These heterogeneous materials are composed of crystalline and glassy solid phases which contain trace metals, presenting a potential risk to the environment. Secondary ion mass spectrometry (SIMS) can provide quantitative chemical information, in particular the localisation of metals at trace level. Unstable glassy phases formed during incineration are present in relatively high proportions. Their analyses suggest a continuum between melilite-bearing glasses and dark glasses enriched in iron with abundant spinel aggregates. These primary glasses are enriched in zinc (~4500 ppm) but depleted in lead (~800 ppm) by comparison with the bulk chemical composition and reference materials. Heterogeneous cementing and encrusting admixtures on coarse grains are studied in a second step. SIMS imaging suggests a superposition of band zones including an intermediate layer enriched in iron oxyhydroxides and a superficial layer with calcium accumulation. A strong spatial association between lead and iron is systematically observed. Extended X-ray absorption fine structure (EXAFS) supports these observations by demonstrating that lead co-precipitation within iron oxyhydroxides, or sorption on their surfaces, may be a main containment process in the cementing and encrusting admixtures, whereas lead speciation is globally more complex in MSWI bottom ash.

Jan 1, 2008

By McLennan R. G

Mr. F. Cavanaugh (E.R.S. Co. of Aust. P'ty. Ltd.) ; What is your opinion of the expendable gauze type respirator? Would you give your views on what type of training is most effective to improve the safety consciousness of "new" New Australians?Mr. Lewis: For many jobs, the expendable gauze respirators are quite satisfactory. However, where silica dust of less than 10 micron sizing is present, they Cannot be recommended. Generally, they are more acceptable to the men than the heavier but more efficient types of industrial respirator.The best avenues of approach to training appear to be:(a) Liberal use of vi~ual aids (posters, photos, slides, etc.)(b) Efficient interpreter service.(c) Constant follow-up and check by foreman and fellow workmen.Mr. W.Marsden (B.H.P. Collieries); Most colliery employees only wear masks when they can see dust which, of course, is not the hazardous dust, and they take the mask off when they can't see the dust and so expose themselves to the hazard which is often present.Mr. W. W. SoIIy (S.A. Mines Uranium Treatment Plant) ; Safety equipment as supplied by manufacturers is inefficient and short of safety and common sense requirements-operators don't wear equipment because it is uncomfortable, clumsy, or unsightly. In the case of face masks,* they are not completely, effectively sealed; hard hats should be made even lighter and yet efficiently strong; concerning gloves, it seems not too much to ask of suppliers to put up a durable glove, preferably lined for comfort, with the maximum amount of "feel". Adaptation of, say, tubeless tyre methods...

Jan 1, 1958

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By Lock PR

The Silver Swan nickel mine is located at the Black Swan Nickel Project, 53 kin north east of Kalgoorlie, Western Australia. The Silver Swan orebody is a massive sulphide nickel deposit dipping 70¦ east with an average in situ grade of 14 per cent. Mining of the massive orebody is by Mechanised Ramp Cut and Fill (MRCF). A mining recovery of 98 per cent and minimising dilution are primary goals in extracting the high-grade ore. Placing a distinguishable marker bed (working platform) on rock fill was identified as a key method to achieving these goals. Gravel from a pit located onsite was considered the most suitable material for the marker beds. Research undertaken to design the marker beds using the gravel revealed conventional methods used in mining would not suffice, but that road stabilisation methods could be a viable alternative. Trials used a road recycler to mix cement and gravel in situ and several test beds were constructed on the surface to determine the final design. The trials attempted to replicate a marker bed's life cycle of construction and placement and mucking of ore from the marker bed.

Jan 1, 1998

By S Grano, M Fordham, H Manouchehri, J Curral

This paper focuses on the impact of high pulp temperature on sphalerite flotation after the zinc regrind circuit in the Zinc Plant of Somincor, owned and operated by Lundin Mining Corporation. In the zinc circuit, the zinc rougher concentrate is reground with forged steel media before flotation with one stage of roughing and scavenging, and three stages of cleaning to obtain a zinc final concentrate (zinc grade >50 per cent). After regrinding, sphalerite flotation has been found to be seriously affected by high pulp temperature which may occur during the summer months. Mineral recoveries were found to be seriously reduced at pulp temperatures above 60¦C. At this high pulp temperature, neither elevated copper sulfate concentration nor a decreased pH alone appreciably increased Zn recovery. However, a combination of these two (eg a decrease in pH from 11.5 to 10.8, and an increase in copper sulfate dosage from 400 g/t to 800 g/t) was found to reduce Zn depression at high pulp temperature. At pulp temperatures below 45¦C, the negative influence of pulp temperature on mineral recoveries was minimal. A systematic series of flotation tests and solution/surface analyses were performed to reveal causes for poor sphalerite flotation at high pulp temperature after regrinding. The decrease in mineral recovery was shown to be associated with variations in the surface species on mineral particles in response to the increased pulp temperature. These variations in the surface species include collector desorption and superficial oxidation to form lead/zinc oxide/hydroxides on mineral particles. The influence of the type of regrinding media on sphalerite flotation at high pulp temperature was also addressed in this work.

Jan 1, 2008

By H Sichani-Teimouri, B N. Noller, J C. Ng, R N. Alsaadi, P L. Breuer, S Shini

Cyanide has been used for over a century worldwide for gold extraction. However, the presence of several metals and metalloids in ore requires greater amount of cyanide for an efficient gold recovery due to their solubilisation in conjunction with gold. The extraction residues are discharged into tailing storage facilities (TSFs) and may cause bird mortality if there is exposure to cyanide-bearing wastewater exceeding the toxic threshold. The toxicity arises from free cyanide released from weak acid dissociable (WAD) cyanide complexes. The International Cyanide Management Code (ICMC) has deemed 50 mg/L of WAD cyanide released into TSFs to be safe for wildlife protection. However, this concentration is based on observations of an apparent lack of toxicity rather than a toxicological approach. The National Industrial Chemicals Notification and Assessment Scheme (NICNAS) identified in 2010 that there is a lack of toxicity data to properly assess the environmental significance of cyanide levels at gold mines. Lack of knowledge for the toxicity of free cyanide and metal cyanide complexes to wildlife led to consider alternative direct assessment techniques for designating safe levels. Whilst toxicity may be assessed by using young chickens with animal ethics approval, the traditional bioassay approach to assess cyanide toxicity is impractical for gold mine TSFs. Bioassays using algal species such as Euglena gracilis, a unicellular alga, are widely used for ecotoxicological studies. A unique feature is that the Euglena gracilis Z cell has plant-like while SMZ cell has animal-like characteristics. The aims of this project are to evaluate the suitability of Euglena gracilis Z and SMZ strains to assess the toxicity of free cyanide and both strong (cobalt) and weak (zinc, copper and nickel) acid dissociable metal-cyanide complexes that may be present in TSFs.CITATION:Noller, B N, Ng, J C, Shini, S, Breuer, P L, Sichani-Teimouri, H and Alsaadi, R N, 2014. Development of a toxicity approach to evaluate free cyanide and metal cyanide complexes in waters associated with gold and other mining, in Proceedings Life-of-Mine 2014 , pp 573–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Butler I. K, Nicholson P. M

There are four main types of base metal and gold mineralisation recognised in the central Pine Creek Geosyncline. These are stratiform, polymetallic veins, stockwork/concordant gold-quartz veins and unconformity related uranium-gold-platinoid mineralisation. The stratigraphy of the central Palaeoproterozoic Pine Creek Geosyncline has been simplified into three groups comprising the Batchelor, Frances Creek and Finniss River Groups in ascending order. Stratiform mineralisation occurs within the Frances Creek Group. The earliest mineralisation is found adjacent to circular faults ringing basement highs. Higher in the stratigraphy, stratiform mineralisation is often associated with zones of high compression in the vicinity of basement highs. A synsedimentary-diagenetic origin for stratiform mineralisation is proposed. Polymetallic vein mineralisation occurs within the Frances Creek and Finniss River Groups. Its composition changes systematically through the stratigraphy similar to the stratiform mineralisation. The mineralisation is structurally controlled and usually occurs in the vicinity of basement highs. Stockwork-concordant gold-quartz vein mineralisation is hosted by the upper Frances Creek and Finniss River Groups. It occurs within compressional zones and along the Pine Creek Structure corridor around, above and particularly between basement highs. Mineable reserves occur in thick continuous semi concordant quartz-sulphide veins and/or stockworks. Unconformity related uranium-gold-platinoid mineralisation shows a close spatial relationship with the Palaeoproterozoic/Mesoproterozoic unconformity. The mineralisation is localised by structures formed during Mesoproterozoic deposition and is commonly adjacent to Archaean basement or its remobilised equivalents. The type of mineralisation (stratifom/polymetallic vein) is a reflection of local stress regimes, structure and physio-chemical conditions. An initial phase of stratiform mineralisation is postulated to have occurred with the first significant marine transgression in a tensional regime. A second phase occurred later during a compressive regime. "Ihermochemical sulphate reduction of mineralising fluids by hydrocarbons is invoked as the precipitation mechanism for the polymetallic vein type of mineralisation. Hydrocarbon generation is postulated to have occurred within the Frances Creek Group, in many places contemporaneously with the movement of mineralising fluids and basin compression. Polymetallic veins formed from the interaction of mineralising fluids and hydrocarbons which were trapped in suitable structures. An abundant, continuing supply of hydrocarbons was necessary to form significant deposits. Where these conditions were not net, the mineralising fluids largely continued their ascent to the near surface environment to form stratiform deposits. The stockwork/concordant gold-quartz vein mineralisation is a later event and occurred during the relaxation of compressional defonnation after deposition of the 1-inniss River Group.

Jan 1, 1994

By R Ulusay

Rock mechanics involves characterizing the mechanical properties and behaviour of rock material and the natural discontinuities of the rock mass, while rock engineering is concerned with specific engineering circumstances, for example, how much load will the rock support and whether reinforcement is necessary. Rock engineering models developed depend considerably on the input data such as boundary conditions, the properties of rock material and rock mass. Correct evaluation of these properties frequently requires laboratory and in-situ tests, supplemented with a high degree of experience and judgment. Accordingly, since 1974, the ISRM Commission on Testing Methods has spent considerable effort in developing a succession of the ISRM Suggested Methods (SMs) for different aspects of rock mechanics and rock engineering with the contribution of a number of working groups and cooperation of some other ISRM Commissions. This paper emphasizes the need and importance of standardization of rock testing methods within the context of the ISRM SMs, gives a guideline for developing ISRM SMs and finally discusses on some implementation and contractual issues associated with rock testing and experienced in practice, and briefly introduces main future trends in rock characterization, testing and monitoring. This is an extended abstract only. CITATION:Ulusay, R, 2018. Standardisation on rock characterisation, testing and monitoring with emphasis on ISRM suggested methods, practical issues and difficulties, and future trends, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 17–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Blin, R Walde, R Belli, D Inaudi

A fiber optic distributed sensing system allows the monitoring of parameters useful to determine the short- and long-term behaviour of the structure in response to the external actions, including, eg seismic activities as well as long-term phenomena such as seepage, tunneling, sinkholes, and other geo-structural movements. Monitoring of large retaining structures with such a system provides direct strain/deformation and temperature measurements on the broad interior area with an arrangement of several sensing cable lines, enabling early detection, localisation and sizing of subsurface damages. Measurements are provided every meter along the entire sensing cable, this is particularly important in such cases where the location of defects and damages cannot be predicted. Fiber optic distributed sensing cables are generally available for retrofit installation inside the dam structure using trenches on the downstream face or laid during construction below the geomembrane liner within the bedding sand layer. Mapping the cable route enables exact correlation between a linear coordinate on the cable length and a position in the dam. Cable installation is envisaged to be carried out during further raising of the embankment; additional cable sections are plugged to the previously installed cables and measured with the existing measurement system, requiring only an update of the mapping. The measurement system is placed remotely from the sensing area since a section of sensing cable can be used to link to the sensing area at the storage facility several kilometers away. The system is available for on-line, 24/7 real-time operational data management. Such fiber optic distributed sensing systems allow storage facilities to be monitored with long, accurate, continuous and precise data for geotechnical diagnostic purposes. This contribution will introduce the principles, benefits, and limitations of this technology.

Jul 1, 2021

A mining operation can be identified as demonstrating prudent management when a number of vital characteristics are evident.All risks and opportunities that are critical to the on-going success of the operation have been identified and are being effectively managed. All significant tasks and events are plan driven. All levels of management visibly support the policies of the operation through their attitude, behaviour and actions as well as words. Supporting evidence for required activity and the outcomes is readily available. Improvement mechanisms are working to advance the key business processes. Everyone is working towards satisfying the needs of the stakeholders of the operation. When these characteristics are integrated with the satisfaction of all legislative requirements, all industry codes and optionally all relevant international management system standards then an operation is fulfilling all the requirements of a Due Diligence Process. The majority of mining operations do not show all of these characteristics and therefore unnecessarily suffer from missed profit opportunity and constant cost pressure, less than acceptable safety and health and environmental performance and consequent poor relations with employees, unions and regulators. In these operations the characteristics to be observed are quite different.Serious incidents are occurring with no sign of a rate decrease. The operation lurches from one panic ituation to another. Management are absent in their leadership, but very active in developing rules and enforcement methodologies. The operation has no history. Re-inventing the wheel with employees who come and go at an alarming rate seems to be forever occurring. All efforts are directed at controlling the business outputs with a strong emphasis on blame. Everyone is trying to look busy to avoid the ever-present cost reduction threats. To change to more prudent management utilising a Due Diligence Process is not theoretically difficult. However it does take clear direction, focussed efforts, supporting actions with appropriate tools and perhaps most importantly an internal desire and drive to become such an operation. A Due Diligence Process is about doing the important things that have to be done, providing the understanding of why they are important, demonstrating proof of activity and effectiveness, and leading the way through effective management.

Jan 1, 1998

By C Tapia Cortez, A G. Dempster, R Fradet, S Saydam, T de Roche, R Shishko, J Coulton

Human ventures into space are entering a new phase in which missions formerly driven by government agencies are now being replaced by those led by commercial enterprises – in launch, satellite deployment, resupply of the International Space Station and space tourism. In the not-too-distant future, commercial opportunities will also include the mining of asteroids, comets, the Moon and Mars. This research examines the role of off-Earth mining in a growing space economy. In this investigation, the term ‘mining’ is taken to embrace minerals, ice/water and other in situ resources. As the off-Earth mining initiative could be the engine that drives the space economy, it would be useful to understand what off-Earth mining market conditions and technology requirements are needed for that economy to prosper. These specific elements are studied in the wider context of creating an economy that could ultimately support a sustainable Mars colony. The methodology for developing the model focuses on the extraction of ice from the surface of Mars to produce propellant and water for life support for a possible colony.CITATION:Saydam, S, Shishko, R, Tapia Cortez, C, de Roche, T, Fradet, R, Coulton, J and Dempster, A G, 2015. An integrated economics model for in situ resource utilisation in support of a Mars colony, in Proceedings Third International Future Mining Conference, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By D Matthews

Increases in mining and production capacities can have a major impact on the productivity of a mining and production facility during the construction and commissioning period. With minimised production loss in mind, a multi-phase modular plant design was implemented on the Khumani Mine in the Northern Cape, South Africa. The first phase involved a run-of-mine (ROM) crushing facility and the subsequent modular processing facility with capacity for 8.4 million tons per annum (Mt/a) product. An interim phase comprising modular additions to the processing facility increased capacity to 10 Mt/a product, with tie-ins occurring during maintenance periods. The second phase involves a second ROM crushing facility and modular additions to the processing facility, increasing capacity to 16 Mt/a product. This paper outlines the design considerations and limitations with modular design that need to be considered and shows how effectively construction and commissioning were implemented within shut-down and maintenance periods.

Jul 11, 2011

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

By Marsham B, Baker D. C

The expansion of New Broken Hill Consolidated Limited (NBHC) concentrator necessitated the installation of hydrocyclone classifiers where rake classifiers had previously been used. Commissioning of the circuit and optimisation of circuit performance has highlighted problems related to classification of sulphide minerals. Testwork initiated to solve these problems has been used to develop cyclone models which have been incorporated in a ccnputer control strategy for the grinding circuit as a whole. The modifications to the circuit during the commissioning phase and the control philosophy are outlined.

Jan 1, 1983