Search Documents

By Kavanagh M. E, Henley R. W

The Meekatharra mining district lies in the northern pan of the Murchison Province of the Archaean Ynlgam block of Western Australia. Since dis- covery of the Paddy's Flat belt in the district in 1897 total gold production has been 67 tonnes and a further 33 tonnes in resources have been defined by drilling. The Paddy's Flat gold deposits occur within the Gabanintha Formation, a basal formation of the Murchison greenstone sequence containing komatiitic basalts, ultramafics and minor banded iron formations. The regional control on the distribution of deposits is an anastomosing shear belt which extends over 350 km and incorporates the Mt Magnet, Reedys and Meekatharra deposits. The following gold deposit styles may be recognized based on lithological association and alteration: Albite porphyry hosted, Carbonate-fuchsite- quartz alteration hosted deposits, Banded Iron Formation hosted sulphide replacement gold deposits and quartz vein deposits. With the exception of the banded iron formation hosted deposits, the Paddy's Flat alteration zone shows strong similarities to the alteration styles at Kerr-Addison (Ontario).

Jan 1, 1991

By I Zulkarnain, H Permana, R A. Binns

Through an ambitious but relatively low-cost program of marine fieldwork, laboratory investigations and technology-transfer and training activities, three Indonesia-Australia-led marine expeditions were undertaken aboard KR Baruna Jaya VIII between 2001 and 2003. These IASSHA (Indonesia-Australia Survey for Submarine Hydrothermal Activity) cruises have sought to discover and investigate a variety of potential ore forming hydrothermal systems in a range of tectonic settings. All cruises have been successful, both scientifically and from the point of view of training, creation of capabilities and capacity building for such research in Indonesia. Over 60 scientists and technicians from Indonesian and Australian institutions and agencies have been involved. Three new sites and a possible fourth site of hydrothermal activity were discovered in the Sangihe arc in northern Sulawesi. Surveys in the Tomini basin tested a hypothesis based on previous data which suggested this might be an isolated anoxic, brine-filled basin over 2000 m deep where igneous heat sources existed to generate hydrothermal mineralisation. The bay, however, was found to be open to adjacent deep ocean circulation, and there was no evidence of massive base metal sulfides. Subdued evidence of hydrothermal activity was found in the Sunda Strait associated with the famous Krakatau volcano and the extension of the seismically active Semangko Fault. The BANDAMIN program (Indonesia-Germany) covered a portion of the Banda arc in eastern Indonesia, and also found evidence of recent hydrothermal activity and epithermal sulfide mineralisation.

Jan 1, 2004

By A Hutton, C Dick, D Fletcher

Mine and facility closure planning is a dynamic and rapidly evolving landscape. In this landscape, mining companies and industry consultants are generally good at estimating the associated earthworks and rehabilitation costs, because it is æcore businessÆ. Through our extensive work in mine closure, we have found that the safe and cost-effective demolition of mining related infrastructure is often grossly underestimated. Or alternately, it is simply assumed that the returns on scrap steel and the sale of re-usable plant will cover the related costs. With fluctuating steel prices and no guaranteed buyer for the assets, the estimated monetary return is often unreliable and in many cases unrealistic. On this basis this logic is fundamentally flawed. We have found that on most occasions this has meant that closure cost estimates fall well short of what the actual costs are to close the mine.GSSE and Liberty Industrial have worked on over 60 mine closure projects in Australia and overseas of varying scales and across a range of commodity types. An evaluation of these projects has shown that costs associated with the safe demolition and removal of a mining related infrastructure is in the order of 20 - 30 per cent of the total cost at closure. We believe it is one of the top three risk areas associated with mine closure planning and cost estimation, alongside bulk earthworks and the capping of tailings and waste rock storage facilities.Our paper uses examples from recent projects to demonstrate all aspects outlined above. We have also endeavoured to address the following key points related to the demolition and removal of mining related infrastructure:If companies fail to plan appropriately, complicating factors such as contamination, hazardous materials, mobilisation/demobilisation, geographical location, decommissioning standards, site constraints and weather, can add considerable costs to the project and result in variations for the demolition contractor.Closure planning often assumes infrastructure that is no longer required can be utilised by a third party and/or the new land holder. We intend to show that unless adequate consultation and planning is undertaken, this is not beneficial to the mining company, the environment, or the local community.CITATION:Fletcher, D, Hutton, A and Dick, C, 2012. The æsmoking gunÆ of detailed mine closure cost over-run - A review using case studies of the real costs associated with the demolition and removal of infrastructure in mine closure, in Proceedings Life-of-Mine 2012 , pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By P Sha

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Elaine Dorothy Cu-Au (REE-U) skarn deposit in the Mt Isa Inlier, Queensland, Australia is characterised by extensive metamorphic calc-silicate hornfels long before hydrothermal skarn and complicated deformation history. The deposit is hosted by the Corella Formation (1780–1740 Ma) and exhibits two phases of skarn formation in the study area – banded fine-grained diopsidic hornfels (Phase 1) and coarse-grain pyroxene skarn (Phase 2). Phase 1 skarn is predeformation and is interpreted to have been caused by the 1743–1734 Ma Burstall Magmatic Suites, whereas the coarse-grained pyroxene skarn (Phase 2 skarn) postdates the deformation and peak metamorphism events. Phase 2 skarn consists of prograde pyroxene, less garnet and titanite, retrograde epidote, REE-allanite, amphibole, biotite, and later sulfides, carbonate, quartz, anhydrite and chlorite. It hosts most of the copper mineralisation, with the REE elements occurring mostly in allanite. Titanite coexisting with allanite and Cu-Fe sulfides in Phase 2 skarn has been dated by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) at 1524 ± 9 Ma (207Pb/206Pb). The ages are similar to Williams-Naraku Batholiths, which outcrop approximately 40 km to the east in the Eastern Fold Belt. In Elaine Dorothy, the isotopic compositions for calcite cluster around 12.2‰ d18O and -3.7‰ d13C. It probably resulted from a mixing processes between marine sourced carbon-oxygen (ca 20‰ d18O and -0.5‰ d13C) and other distinct geochemical reservoirs, eg magmatic C-O. These features indicate that Phase 2 skarn and Cu-Au (REE-U) mineralisation may be related to unexposed intrusions at deeper levels.CITATION:Sha, P, Spandler, C and Chang, Z, 2015. Elaine Dorothy Cu-Au (REE-U) skarn deposit, in Proceedings PACRIM 2015 Congress, pp 445–450 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P J. Bangerter, J Pan

Optimising for Net Present Value (NPV) with a strategic optimiser such as COMET, Prober-E, Blaser or Minemax has hitherto lacked a dynamic method for analysing the so-called third-order outcomes (such as Carbon emissions) of optimisation within life-of-mine planning. Optimisation, per se, has natural effects on carbon emissions in a life-of-mine plan. Contemporary strategic planning employs a mathematical optimiser to make sense of non-linear data (ie a block model) and produces a best-NPV optimised mining schedule, within a set of constraints. The very act of optimisation influences emissions, and in a dynamic way.

Aug 2, 2023

By R Steinhaus, D M. Frantois-Bongarton, P W. Cleary, G K. Robinson, M D. Sinnott

Multotec Process Equipment and Dominique Frantois-Bongarton have a patent for a mineral sampling device, which they call a æTrue-Belt SamplerÆ. This uses a plough, which is rotated about an axis parallel to a conveyor belt to throw material off the belt. A fixed sample cutter takes a sample from the material thrown off the belt.Discrete element modelling has been used to consider a range of plough designs, plough speeds, positions for the cutter relative to the plough, cutter apertures, cutter designs and frictional properties, prior to the building of a physical prototype. This modelling work will be discussed, both as an illustration of the role of modelling in the development of new materials-handling devices and in order to explain the likely strengths and weaknesses of this new type of sampling device.CITATION:Robinson, G K, Sinnott, M D, Cleary, P W, Steinhaus, R and Frantois-Bongarton, D M, 2012. Modelling of a ætrue-belt samplerÆ - A new device for sampling from a conveyor belt, in Proceedings Sampling 2012 , pp 33-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By D Fargher

BHP BillitonÆs Cannington operation began production in 1997 and is presently the largest tonnage and lowest cost single mine producer of both lead and silver in the world. The original design capacity was 1.5 Mtpa and this has progressively increased via a series of debottlenecking projects in both the mining and milling operations. In 2003, 2.39 Mt of ore was mined, whilst 2.31 Mt of ore was milled. In February 2003 Cannington received approval to expand the project to a sustainable capacity of 2.4 Mtpa. This resulted in underground development into the northern zone, upgrades to the concentrator, increased accommodation at site and power station capacity. The Cannington project development team implemented a partnership approach to the project. Fraser Osborn Engineering and Outokumpu Technology worked closely together with the Cannington team to meet all of the project constraints.

Jan 1, 2004

By J Andrina, D Richar, R Smart, A Neale

The Grasberg is a large copper and gold open pit mine operated by PT Freeport Indonesia and located in the high equatorial mountains of Papua Province, Indonesia. The climate is alpine/sub-alpine with little seasonal variation in temperature and rainfall. The annual precipitation varies from about 3000 to 5000 mm over short distances around the Grasberg, but in general, an average daily precipitation of 10 mm per day applies and leaching of the overburden is continuous throughout the year. Mining commenced in 1988, and almost all of the overburden mined up to 2003 was potentially acid forming. From 2003 to the end of the Grasberg pit operation in 2014, approximately 70 per cent of the overburden will be potentially acid forming and 30 per cent limestone. A major focus of the investigations is developing strategies to maximise the beneficial use of the limestone that will be mined. Laboratory columns and field test pad investigations have been ongoing for six years examining limestone blends. Trial dumps utilising truck placement and conveyor/stacker placement and blending of limestone and acid generating rock have recently been constructed. In addition, based on initial results, investigations aimed at further evaluating the performance of limestone covers in this high rainfall environment have commenced. A significant finding has been the identification of strong armouring layers on sulfide surfaces within well-blended material and under limestone covers. These layers effectively isolate sulfides and thus progressively slow the oxidation rate to a level where the alkalinity load from the limestone exceeds the rate of acid generating. ARD is controlled and neutral low metal drainage results. The results have demonstrated that although limestone blending is effective, it is necessary to ensure that all size fractions within the blend receive adequate acid neutralising capacity to buffer the potential acidity. Because the sulfur content generally increases and the acid neutralising capacity decreases with decreasing particle size in limestone blends, the amount of limestone required greatly exceeds the stoichiometric requirement. This paper describes the development of limestone blending specifications for potentially acid forming overburden and presents the results of the ongoing limestone cover trials at the Grasberg mine.

Jan 1, 2003

This paper is for mine managers. It is about maintenance of mining equipment. This is an extremely broad subject so this paper is given with the caveat that it necessarily contains generalisations, not true in all cases, but broadly correct. The job of mine managers is to be good at making money from the excavation and preliminary treatment of mineral. To do this well, they need to understand the cost and value drivers in the business. This includes understanding the drivers associated with maintenance. Maintenance is often identified as a problem at mine sites. It is frequently listed as the cause of production shortfalls when reporting. The state of maintenance within mining as an industry is generally among the lower end of the range, when compared to manufacturing, petrochemicals, etc. Why is this? Experience and review of many audits and evaluations of maintenance has shown that some patterns are consistent with good performance and some consistent with poor performance. These often centre around the time horizon of the management team and are associated with knowing the sensitivity of the business to certain maintenance drivers and the mechanisms of maintenance and their results. To summarise, some common misunderstandings can be listed as statements that are obvious and extrapolations from those, which are not necessarily correct. For example: High availability of equipment is necessary for production. Incorrect extrapolation:focus on availability will produce high production. Design is often the greatest factor in determining the reliability of a mining machine. Incorrect extrapolation: the newest and biggest machines generally have the lowest cost operations. Operation has an enormous impact on machine productivity and reliability. Incorrect extrapolation: the fastest operators are generally the best from a productive point of view. Some maintenance improves the performance and reliability of machines. Incorrect extrapolation: more maintenance will give you more reliability. Some maintenance depends on disassembly and reassembly of components. Incorrect extrapolation: assembly is basically the reverse process of disassembly. Maintenance improvement in the mining industry in the last 15 years has focused largely on planning and systems improvement. Incorrect extrapolation: most of the problems in maintenance can be traced to a lack of planning. Actions based on flawed extrapolations will steer a business suboptimally. It is therefore important that the mine manager understands these issues so that the improvement effort can be directed to the greatest benefit.

Jan 1, 2006

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

The underground storage of LPG and other hydrocarbons is in current commercial use in Northern Hemisphere countries in Europe, Asia and the USA.Elgas Pty Ltd, a 50 per cent joint venture between AGL and BOC, embarked on a worldwide feasibility investigation in 1989 to establish the viability of constructing an underground LPG storage facility in Sydney, Australia, the first of its kind in the country. Elgas recognised that with the limited 19 000 tonnes of storage capacity at Port Botany and the limitations imposed by use of small coastal ships (up to 10 000 tonnes capacity), a larger storage facility was required to utilise higher capacity ships from more remote sources such as the North West shelf and overseas. This would achieve security of supply in high demand periods and economies of scale. The underground option also provides improvements to safety and environmental standards.

Jan 1, 1999

Single station group velocities of fundamental made Rayleigh waves over the period range 15-100 s are carguted for five provincial profiles of the West Pacific. Based on recordings of earthquakes around the West Pacific by the W~ (World Wide Standard Seismic Network) stations AFI (Afianalu), HNR (Honiara), WEL (Wellington), PAR (Raratonga) and RAB (Rabaul). The inversion of the derived dispersion curves for average shear velocity-depth structure of the crust, LID and LVL shows that (i) the over-all structure beneath the profile 'westernSamoa-Micronesia-Mariana' is in between that of regions 3 and 4 of Pacific Ocean (Yu and Mitchell, 1979), except that the velocity is slightly lower, (ii) the uppermost mantle beneath the 'Vitiaz Trench' profile between AFI and HNR is similar to that of region 2 of the Pacific - in other words, thin LID and thick LVL; (iii) the structure beneath the ' Ibnga-Keradec Ridge' profile has a thick crust with thick sediments, and LID-LVL velocity and thickness are similar to region 3 of the Pacific; (iv) beneath the profiles ' Tonga/ Kermadec Trench events-RAR station' the structure is intermediate between regions 3 and 4 of the Pacific Crean; (v) from decomposition of the 'Solomon-meriana' profile, the structure beneath the Cntong Java Plateau has a thick crust with thick sediments and the uppermost mantle is similar to that of region 3 of the Pacific clean.

Jan 1, 1990

By E Mofya, R Kaunda, P Lever

One of the fundamental requirements for being able to optimise blasting is the ability to predict fragmentation. An accurate blast fragmentation model allows a mine to adjust the fragmentation size for different downstream processes (mill processing versus leach, for instance), and to make real time adjustments in blasting parameters to account for changes in rock mass characteristics (hardness, fracture density, fracture orientation, etc). A number of blast fragmentation models have been developed in the past 40 years such as the Kuz-Ram model (Cunningham, 1983). Fragmentation models have a limited usefulness at the present time because:The input parameters are not the most useful for the engineer to determine and data for these parameters are not available throughout the rock mass. Even if the input parameters are known, the models still do not consistently predict the correct fragmentation. This is because the models capture some but not all of the important rock and blast phenomena. The models do not allow for ætuningÆ at a specific mine site. This paper describes studies that are being conducted to improve blast fragmentation models. The Split image processing software is used for these studies (Kemeny, 1994; Kemeny et al, 1999).

Jan 1, 2001

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A M. Sardo, D E. Sinnett

This study uses the Q Method to examine how those living in former metal mining landscapes value this heritage and their preferences for the long-term management of mine waste. Such sites are often perceived as derelict or degraded, and of very little value. It is therefore assumed that their reuse, for example for development or recovery of metals, is likely to be beneficial. There are around 5,000 former metal mines in England and Wales, many of which are protected for their ecological, geological or cultural value. The Q Method is particularly suitable for issues where there is no consensus of opinion. We asked 38 residents of six mining areas in England and Wales to ‘sort’ a series of statements based on their resonance with the resident’s perspective; this is the Q sort. The statements covered a range of opinions of the mining legacy, its value and options for its management with a particular focus on the potential for metal recovery from the wastes. Analysis of the Q sorts revealed five perspectives on the mining heritage. All placed a high value on the cultural and ecological value of this heritage, however, they differed in their priorities for long-term management. For example, emphasis was placed on either nature conservation, cultural heritage, water quality or the opportunity for job creation through reworking the mines. Cutting across these themes there were also differing perspectives on the role of experts and local people in shaping the future management of the wastes. This research suggests that the views of local people are nuanced; they value their mining heritage but opinion is split on the most effective way to manage these sites especially where there is an impact on water quality.CITATION:Sinnett, D E and Sardo, A M, 2018. Former metal mining areas in England and Wales – local residents’ preferences for the management of wastes, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 126–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Gilligan P

The Selwyn gold-copper operation is wholly owned and operated by the Arimco mining group. The mine is located 150 kilometres south-east of Mount Isa. The primary extraction method for the gold-copper 251 orebody is by sub level open stoping. Secondary extraction is from the mass blasting of the remaining crown and rib pillars. The final mass blast of the 251 orebody occurred in December 1993. This paper details the design and execution of that firing.

Jan 1, 1994

By L Chaffey, M Buckland

The minerals industry has enormous potential to positively contribute to sustainable development and many leading companies have concluded that their long-term success is directly linked to their ability to leave a lasting positive legacy. While there are many examples of success, there have been failures as well and much work has been done in recent years to define the role of the minerals industry in sustainable development and identify the key elements for success. In the past, our sector could point to the taxes and royalties it paid, the exports it generated and employment it created and felt confident that its contribution would be recognised and duly acknowledged. This is no longer the case. Critics of the industry have highlighted resource-rich countries that have failed to capitalise on their resource wealth and have arguably lower standards of living than their resource-poor peers û the æresource curseÆ hypothesis. Recent research has done much to clarify the factors that contribute to a countryÆs success or failure and all stakeholders in the industry now need to include these learnings in their approaches going forward. We know that our long-term success relies on embedding a company- wide approach to sustainable development into all aspects of our business operations. In this paper we highlight BHP BillitonÆs experience in the development and implementation of policies and systems designed to enhance our contribution to sustainable development. We detail the business drivers for excellence in this area and the key external codes and initiatives that have shaped our approach. The values-based BHP Billiton Charter, Sustainable Development Policy and associated Health, Safety, Environment and Community (HSEC) Management Standards are central to our approach. Implementation is reviewed through our HSEC audit program. One area in which we have placed particular emphasis is our approach to community development. BHP Billiton has a corporate target to contribute one per cent of its pre-tax profit on a three year rolling average to voluntary community programs. As our profit stream has increased with the minerals boom this is approaching an A$100 million commitment. In our paper we detail how we are working to ensure we maximise the value of this contribution for our communities and our shareholders.

Jan 1, 2006

By D Kent, J Bullock, M Wilkinson

Over the last few years at Glencore’s Mount Isa Copper Operations (MICO) mining conditions have become increasingly challenging through lower head grades and higher work indices. MICO has had great success improving operating efficiencies and increasing productivity through focusing on technology, innovation and operational discipline. The recent implementation of the Mine Site Technologies (MST) ImPact System has supported the continued transformation of the MICO operations through improved personnel safety and direct measurement of productivity. The ImPact System has implemented new safety systems such as the heavy vehicle proximity detection system, underground personnel tracking system and emergency evacuation dashboards improving the overall safety of the workforce. The ImPact System has facilitated productivity improvements via real-time equipment and personnel monitoring, and the implementation of exception reporting (personnel productivity), KPI reports and production dashboards, and transparent reports highlighting developing maintenance issues.This paper discusses the components of the ImPact System, the current installation at MICO, and critically analyses the implementation processes and right sizing of the system to meet the needs of the business today and into the future.CITATION:Bullock, J, Kent, D and Wilkinson, M, 2017. Productivity and safety improvements supported by MST’s ImPact System at Glencore’s Mount Isa Copper Operations, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 279–286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

The Que River and Hellyer polymetallic massive sulphide ore bodies are located 3 kilometres apart in the Cambrian Mount Read volcanics of Western Tasmania. Both deposits are classic examples of the Kuroko volcanogenic style. Base and precious metal rich hydrothermal solutions rose through a deep fracture system and vented on the sea floor, causing sulphides to accumu- late in adjacent topographic lows. Together the preproduction geological resource is approximately 23 million tonnes at greater than 18% zinc plus lead, with economically significant silver and gold. Exploration by Aberfoyle in the Mount Read volcanics com- menced in 1970. Que River was discovered in 1973 following a comprehensive data review, a regional stream geochemical survey and a helicopter-borne electromagnetic survey. Production began in 1981, and the mine is currently producing 300,000 tonnes per year. The ore is sold to the Electrolytic Zinc Company of Aus- tralasia Ltd mill at Rosebery. Ten years of extensive geological mapping, soil geochemistry, and induced polarisation, combined with continual study of the Que River orebody and its host rocks, formed a strong frame- work for the discovery of the Hellyer deposit, which was found as a result of drilling .a subtle time domain electromagnetic anomaly in 1983. Hellyer is currently being mined at a rate of 250,000 tonnes per year, with the ore being concentrated at Aber- foyle's converted Cleveland tin mill. Treatment of 1 million tonnes per year will begin in early 1989 at a new mill located near the Hellyer site.

Jan 1, 1988

By A L. Stewart, M Baatar

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Middle Palaeozoic Gurvansaikhan Belt (Southern Mongolia) of the Central Asian Orogenic Belt is one of Central Asia’s most significant emerging porphyry copper provinces. The belt has become the focus of extensive exploration for porphyry copper-gold deposits over the last decade following the discovery of the giant Oyu Tolgoi porphyry copper-gold deposit. The Gurvansaikhan Belt is known to host porphyry deposits of Late Devonian (~370 Ma) and Early Carboniferous (~320 Ma) age. The characteristics of Early Carboniferous porphyry systems are poorly known compared to their older counterparts, despite their probable abundance and potential economic significance. Exploration within the Kharmagtai porphyry breccia complex has identified multiple cogenetic gold-copper-porphyry centres and late-stage mineralised magmatic-hydrothermal tourmaline breccias emplacement within a composite high-K calc-alkaline quartz monzodiorite intrusive complex. Early porphyry alteration and mineralisation at Kharmagtai are zoned around vertically attenuated early- and inter-mineral quartz monzodiorite dykes and stocks and comprises a complex sequence of calc-potassic, potassic and propylitic assemblages. Hematite dusting is a common alteration product that gives intrusions and the host rocks a distinctive pink-orange colour. Several of the systems have bornite-rich cores, where mineralisation is characterised by high gold grades (0.7 to >5 g/t Au) that zone outward to chalcopyrite-rich and then outer pyritic halos. Early stockwork mineralisation is overprinted by magmatic-hydrothermal tourmaline breccias. High-grade magmatic-hydrothermal tourmaline breccias form part of a major copper-gold mineralised breccia system with significant exploration potential. The Early Carboniferous porphyry copper-gold systems of the Gurvansaikhan Belt represent a substantial exploration challenge in an area of increasing exploration maturity. This paper summarises the characteristics of the Kharmagtai porphyry system that have helped to define the Early Carboniferous porphyry province of the Gurvansaikhan Belt and discusses implications for future exploration.CITATION:Stewart, A L and Baatar, M, 2015. The Kharmagtai porphyry breccia complex – characteristics of early Carboniferous porphyry mineralisation in the Gurvansaikhan Belt, Southern Mongolia, in Proceedings PACRIM 2015 Congress, pp 383–388 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015