Search Documents

Teleseismic travel time residuals measured on 600-1000 km seismic arrays across the Rio Grande and East African rifts provide evidence for upper mantle low velocity zones beneath each rift of velocity contrast 6%-8%. Refraction studies show thinning of the crust below the rift axes. Regional uplift which extends hundreds of km either side of the axes, is isostatically compensated by negative density contrast at depth. Since the refraction argues against compensation by thickened crust, compensation in the upper mantle low velocity zones is suggested. Temperature effects alone can not explain the reduced velocities. Generation of a few percent of partial melt is the most probable source of the reduction. A passive extensional mechanism is investigated for the Rio Grande rift in which hot asthenosphere intrudes the lithosphere raising its temperature and generating moderate melting. It requires less than 1% extension to explain the melting but a prodigious 26% to raise the temperature from a pre-rifting continental geotherm to the solidus. Geological estimates find that extension is less than 10% over the uplift zone. Such a mechanism is possible only if the prerifting lower lithosphere geotherm lies closer to the solidus than that of stable continent. This is supported by the observed high heat flow in the Rio Grande rift uplift region which, given the long time constant for thermal diffusion, reflects elevated temperatures at depth well in advance of the onset of rifting.

Jan 1, 1987

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

By Y Lin, B J. Seligmann, M Hassall, S Micklethwaite

For multi-site mining companies, checking the quality and consistency of the data recorded in risk registers is important for confirming how well mine safety management systems have been implemented. However, this task is complicated by the differences in scope of the site, their particular nature, the complexity of the operations and many other factors that can introduce nuances to the characteristics of the risk registers. We present here an application of a technique called Causal Network Topology Analysis for comparing the quality and consistency of risk registers. By quality we refer to, for example: - missing causal relationships between risks - location of missing controls - focus of risk treatment strategies: prevention versus mitigation controls. By consistency we refer to how causally interdependent are the risk events. There are often causal interactions between the lines of a risk register that mean that the likelihood and consequence scores that are applied to each risk event are not independent. We measure this degree of interactions by: - proportion of independent scenarios per register - efficiency of risk treatment strategy comparison. This approach can indicate quality and consistency differences between registers irrespective of the actual details of the site or operation. This occurs by comparing aspects of the structure of a causal network extracted from how the risk events, causes, controls and consequences causally interact. In this work we compare pairs of registers to demonstrate the approach.

Apr 16, 2024

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

Effective domaining is fundamental to geostatistical modelling for grade control. Through analysis of lithological, structural and alteration logging data, effective groupings (domains) can be identified and employed for estimation or simulation purposes.The poor definition of domains can adversely affect the grade control model resulting in a misinterpretation of the optimal ore-waste boundary and ultimately reduces the quality of recovered ore. The implementation of an appropriate domaining strategy is therefore expected to improve recovery and reconciliation.A thorough understanding of the geology of the deposit and adequate sample data is required for selecting domains. For new deposits, a resource drill database and resource model may be the only information available. Where extension to a previous operation is taking place, historic grade control, mapping and exposed geology may be used to improve domain selection. Preconceptions about domains, should they exist, need to be re-evaluated and tested to ensure they are fit for the purposes of grade control.While mining progresses, the domain model is re-evaluated to ensure that the previous interpretation is still suitable for the present configuration and geology. The grade control process, being iterative, lends itself to regular review and continuous improvement as further data is collected during the grade control cycle. Regular updates to the geology model, mapping, geostatistical data analysis and review of variography will provide indications of a changing domaining environment.Narrow vein gold deposits, which may have several factors influencing mineralisation, present considerable domaining challenges. By scrutinising the data, sample populations can be grouped into domains, which not only improve ore recovery, but help assist in the development of a mine geology model.CITATION:Matthews, G D, Haylett, M E, Weeks, A and Khosrowshahi, S, 2014. Effective domain selection for grade control in narrow vein gold deposits, in Proceedings Ninth International Mining Geology Conference 2014 , pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

P'his per describes the training and methods development programme in the Concen- trators at Isa Mine. The benefits of such a prosoo .n:e '.__-. _ 'ueen highlighted.

Jan 1, 1978

By B Lumsden

During periods of high metal prices and strong metal demand tailings retreatment can be economic. Most tailings retreatment operations are technically challenging, low margin operations, because the easily recovered mineral has already been removed, therefore, process improvements can potentially yield large economic benefits. The Hellyer tailings dam was owned by Intec Ltd and contained 10.9 million tonnes grading 2.8 per cent zinc, 3.0 per cent lead, 88 g/t of silver, 0.16 per cent copper and 2.6 g/t gold. In November 2006 the Polymetals Group, as operator, restarted the Hellyer plant to retreat these tailings. Within a few months the operation had stabilised and Polymetals was meeting budgeted targets of throughput, metal recovery and concentrate quality. Polymetals and Intec then investigated methods that would improve the metallurgical result for this difficult to treat tailings. Since the tailings are fine-grained with 80 per cent <45 ¦m, magnetic aggregation of the paramagnetic sphalerite was evaluated. Magnetic aggregation of an oxidised tailings feed has not been tested before, nor had the technology been available when Hellyer ore was originally processed. Extensive statistical test work showed magnetic aggregation of the sphalerite fines in the zinc cleaner circuit increased total zinc recovery. The increase in the mean zinc recovery with magnetic conditioning was 3.63 per cent, at a statistical level of confidence of 97.8 per cent, and at the same mean zinc concentrate grade.

Jan 1, 2009

By C W. Lu, Y F. Chen, M J. Lian, W W. Guo

This paper proposes a set of new approaches for the optimisation of planning and designs in mines by means of evolutionary algorithms, which include the determination of ore grade, layout of development system, selection of mining methods and production scheduling in underground mines. The applications indicate that evolutionary algorithms are particularly suitable to the complex and complicated problems in mines.

Jan 1, 2003

By A Fyans, B Ghahreman-Nejad

This paper discusses the method and results of an options study into selection of the optimal form for a 130 m high tailings/water retaining dam, located in a region of high seismicity in central Iran. The proposed dam is part of a planned expansion project for Sarcheshmeh Copper Mine (SCM), which after construction will provide 550 million tonnes of additional tailings storage over the next 27 years. Geotechnical investigation at the proposed site indicated that adequate suitable low permeability materials (i.e. clay) were not available in the immediate vicinity of the dam site and would need to be imported from a distance of well over 10 km (direct). Given the magnitude of the estimated quantity of material and construction cost it was considered prudent to compare the cost of alternative dam design options for the proposed storage. A total of five dam design options are considered including a conventional rockfill embankment dam with an upstream sloping earth core (ECRD), a geomembrane face rockfill embankment dam (GFRD), a sloping asphalt core rockfill embankment dam (ACRD), a roller compacted concrete dam (RCCD), and a filter rockfill embankment dam for tailings storage together with a separate smaller earthfill core rockfill dam (ECRD) located downstream for storage of decant water. The risks, costing and design of all options are discussed in detail and the outcome of the study is presented.CITATION:Ghahreman-Nejad, B and Fyans, A, 2018. Optimum embankment design for a tailings dam, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Cannington Mine is an underground, hard rock, metalliferous mine located in North-Western Queensland, Australia. Weld mesh is installed to prevent the failure of rock from between the installed reinforcement elements. Corrosion reduces the capacity and life expectancy of mesh and presents a real hazard to underground personnel and equipment as it reduces the effectiveness of the support system. Corrosion influences the economics of the mining operation through the need to conduct rehabilitation of the ground support which involves re-installing new mesh or shotcreting over the affected mesh to protect it from further corrosion. The requirement for rehabilitation is determined by the geotechnical engineer based on an individual visual assessment with little or no engineering input. It was identified that a more quantitative method was required that considered the safety and economic risks involved. A project was undertaken to develop a simple method to evaluate corroded mesh and to provide selection criteria for rehabilitation. A weld mesh corrosion classification has been developed that relates the average wire diameter of corroded mesh to the remaining capacity of the mesh. Accompanying selection criteria provides recommendations as to when rehabilitation may be required based on the estimated residual mesh capacity, the remaining development life, and the level of personnel exposure.

Nov 25, 2010

This paper cites selected, prominent examples of current, major projects in Southern Africa in both the mining and civil fields. Differences and similarities in the life cycle of mining and civil projects are discussed. A closer relationship between the mining and civil fraternities is beginning to develop and should be encouraged because of the resultant exchange of experience and technology which benefits both disciplines. An attempt is made to assess future potential for new, major projects and trends in the implementation thereof.

Jan 1, 1999

Gold mineralisation at the Kerimenge-Lemenge prospects is a classical example of myltiple, overprinting events, associated with intrusive-related hydrothermal systems. Repeated emplacement of high level dacitic porphyry bodies (Edie Porphyry; 2.4 - 3.8 Ma) was accompanied by a phreatomagmatic eruption which formed a diatreme-maar complex. Later hydrothermal fluids utilised permeable fault zones and diatreme contacts. Mineralisation took place during two main events. Stage I consists of early quartz - illite/sericite - carbonate phase with associated pyrite-arsenopyrite mineralisation. This phase is zoned from quartz - sericite-pyrite/arsenopyrite in the south at depth, to dominantly manganocarbonate - illitic clay - arsenopyrite- pyrite_s significant base metals in the north and at shallow levels. The majority of known gold (18.1 Mt @ 2.0 g/t Au) at Kerimenge is associated with Stage I activity. The gold occurs primary within the lattice of the sulphides and is metallurgically refractory. Fluid inclusion studies indicate early boiling and progressive cooling and dilution of hydrothermal fluids during the evolution of the Stage I event. Near paleosurface condensation of gases, which evolved off the boiling system at depth, produced abundant low pH bicarbonate fluids. During the waning phases of Stage I activity, these bicarbonate condensate fluids descended down permeable structures and formed banded manganocarbonate veins. High grade non-refractory gold mineralisation during Stage II event is restricted to favourable structures at relatively shallow levels and in the northern regions of the prospect area. Gold in this event exhibits a distinctive Au - Ag - Te -Cu geochemical signature, and is associated with hessite - tennantite - chalcopyrite mineralisation within quartz veining. Alteration and fluid inclusion studies indicate that this style of mineralisation is a result of the quenching of pulses of hot, late magmatic mineralised fluids by the cold condensate waters.

Jan 1, 1997

By P Radulovic, W Y. Lui

The Mount Isa Mines (MIM) copper concentrator at Mount Isa processes both chalcopyrite ore from the MIM underground mine and rotary holding furnace (RHF) slag from the MIM copper smelter. There have been numerous changes to the processing practices since commissioning this concentrator in 1973. Current management of the concentrator extends from grinding and flotation to concentrate handling (thickening and filtration) and tailings disposal (fill plants, tailings thickeners and process water systems).Predominant mill feed through the concentrator is chalcopyrite ore. RHF slag is processed when concentrator production exceeds mined ore production. The chalcopyrite circuit has two stages of grinding in parallel lines (Line 1 and Line 2). Each line has parallel preflotation and rougher banks, combining into a common scavenger/retreat circuit (including regrinding) and common cleaner circuit. RHF slag may be milled in parallel with chalcopyrite, utilising Line 2 flotation roughers and a Jameson cell cleaner. All final concentrate produced is combined and pumped to the concentrate handling plant. The concentrate is thickened, pre-fluxed and filtered in hyperbaric disc filters. Fluxing specification is set by the copper smelter, and filtered product transferred via conveyor belt to the smelter concentrate storage facility.Wet fill and paste fill plants utilise flotation final tailings as hydraulic or cemented hydraulic fill for stopes underground. Cement ratios and fill plant utilisation are varied depending on underground stope fill requirements. Tailings from the adjacent lead-zinc concentrator are also processed at wet fill. All tailings that are not utilised for backfill are pumped via wet fill to three parallel tailings thickeners. Thickener underflows are gravity fed to the tailings dams with thickener overflows recycled for site process water use. In addition to summarising historical operations, this paper will provide a detailed outline of more recent changes in the concentrator flotation circuit, equipment upgrades, reagent optimisation as well as product and process optimisation at the final concentrate handling and fill plants.CITATION:Lui, W Y and Radulovic, P, 2013. Mount Isa Mines copper concentrator - An insight into current and historical practice, in Proceedings MetPlant 2013 , pp 553-574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By B G. Lottermoser

The placement of sulfidic waste below the groundwater table ensures limited interaction with the hydrosphere and suppression of sulfide oxidation. However, if sulfidic waste is placed above the groundwater table and remains uncovered, the backfill becomes part of the unsaturated zone and is exposed to atmospheric oxygen and leaching. This study aims to establish the leaching behaviour of sulfidic waste placed above the groundwater table and the impact of such leachate on the local aquifer at the Thalanga base metal mine. Mining of the Thalanga copper-lead-zinc deposit resulted in a large final mining void (600 m + 150 m + 70 m) and extensive underground workings. The underground workings were partly filled with tailings and the open pit was partly backfilled with acid producing sulfidic waste rock. In addition, the pit serves as a sink for acidic run-off from adjacent waste rock piles and mine workings. To date, the backfill of sulfidic waste rock placed into the pit has not been capped with benign materials and for most of the dry season, the surface of the backfill is covered by melanterite-type efflorescences. Results of kinetic column leach experiments conducted on the sulfidic waste indicate that Cd, Cu, Zn and SO4 rich waters migrate from the backfilled sulfidic waste into the local unconfined aquifer. However, the seepage of alkaline (pH 7.3 - 8.0), high conductivity (>10 000 ¦S/cm) tailings waters into the remaining pit void clearly shows that the acid leachate originating from the sulfidic waste rock does not impact beyond the waste repository and its immediate environment. Geochemical modelling implies that minimal or no mixing occurs between the acid waste rock leachate and the alkaline tailings waters.

Jan 1, 2003

By N Haque, S Northey

Water in mining, mineral processing and metal production on a life cycle basis has been at the top of agendas for various industries, government agencies, research organisations, academic institutions and communities. As a result, a number of water footprint assessment methodologies have been developed. However, their practical applications in mining and mineral processing industries with specific case studies are still rare.A key objective of the Minerals Down Under Flagship is to contribute to the long-term sustainability of the Australian mining and mineral industries. Researchers in the Mineral Futures theme have developed robust assessment methods to evaluate the impact of mining and minerals technology development on the environment. The future of mining and the mineral industry is strongly linked with its sustainability - better water management strategies will need to be implemented.Life cycle assessment (LCA) has been a recognised method for measuring the environmental impacts of products, processes and services. It provides a scientifically sound method of comparing products and processes using a common basis and identifies so called æhot spotsÆ and opportunities for reducing environmental impacts. The water footprint of mining, mineral processing and metal production using an LCA basis is still scarce in the literature. Research methodology is now being applied in detail for copper, gold and nickel. A primary focus has been the relationship between ore grade and water use for which mathematical models are being developed. These types of models provide inputs for LCA of mining and mineral processing plants and can identify water saving opportunities through scenarios and process route analysis.CITATION:Northey, S and Haque, N, 2013. Life cycle based water footprints of selected mineral and metal processing routes, in Proceedings Water in Mining 2013 , pp 35-50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By T Honeyands, L Jelenich

We are currently witnessing large fluctuations in the relative price of ironmaking raw materials brought on by changes in the dynamics of supply and demand, market conditions, environmental regulations and technical factors affecting the iron and steelmaking process. From a customer perspective, it is the behaviour of iron ores in downstream processing that give them their value; their impact on the sintering or pelletising process and subsequently blast furnace ironmaking. It is therefore important to consider this value when developing projects, making mine planning/cut-off grade decisions and in setting price differentials for differing quality.This paper describes the use of the Marx value-in-use model to quantify the downstream value of lump iron ores. The Marx model consists of heat and mass balance modules for sintering and pelletising and a rigorous two-stage heat and mass balance model of blast furnace ironmaking. Mass balance and cost models are applied for steelmaking, casting and rolling. The use of a heat and mass balance allows accurate comparison of the impact of raw material properties on blast furnace operation. The impact of minor elements, such as alumina, silica and phosphorus, and metallurgical properties on ironmaking is described, and examples are given for the calculation of a lump premium.CITATION:Honeyands, T and Jelenich, L, 2015. Lump ore properties and their impact on value-in-use in ironmaking, in Proceedings Iron Ore 2015, pp 359–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Amer S, Novais A. Q, Limpo Gil J

A proprietary hydrometallurgical ammonium chloride process for the recovery of not only zinc, but also copper, lead and silver from sulphidic zinc-rich concentrates has been developed at bench scale by CENIM and INETI (ex-LNET) as part of a research project supported by the Commission of the European Community (DGXII). This paper deals with the innovative chemical aspects applied to this chloride process and also with the more relevant data relating to mass balance, heat balance and process economics. Under mild temperature and oxygen pressure leaching conditions it is possible to extract practically all the zinc together with the other metals of interest and to precipitate simultaneously the solubilised iron fraction as goethite. The pH is kept close to neutrality in spite of the ammonia released in the leaching of the non-ferrous sulphides. A buffer effect is observed mostly due to the formation of zinc ammines which are very soluble in this medium. The zinc is further extracted by D2EHPA, the acidity being neutralised by the ammonia. Most of the ammonium chloride is naturally regenerated in this step. The zinc is recovered as zinc cathodes in a conventional sulphate electrowinning circuit. All the main raw material consumptions excluding the concentrate, such as oxygen, lime and ammonium chloride are linked to the sulphate formation in the leaching step which must be kept as low as possible by decreasing the reaction time under neutral conditions. The process analysis is complemented by the economic evaluation of a reference case. Difficulties encountered in finding a more convenient method of assessing the economics of the process in the absence of a reference price for a complex sulphide concentrate are examined and discussed. The reason why this analysis was performed with a much more optimistic metal prices scenario is also highlighted. The process economics are primarily dependent on the zinc market quotations and of course on the concentrate cost. Around 70 per cent of the total revenue is due to zinc sales. Assuming an internal rate of return of 17 per cent, the price of the concentrate can be as high as 255 $US/t for a plant capacity of 320 000 t/y (90 000 t/y of zinc).

Jan 1, 1993

By T Casten

Freeport IndonesiaÆs DOZ (Deep Ore Zone) mine is scheduled to commence production in the second half of 2000. The DOZ will produce 25 000 tpd using mechanised block cave mining methods and will have a number of major improvements when compared to previous block cave mines in the district. The DOZ will have an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system than in previous underground mines in the district. This paper will describe the mine plan, haulage, and ventilation systems, and compare them to those used in other operations in the district.

Jan 1, 2000

By P Knights

This paper examines the process and specialised skills required to extract insight from data routinely collected by mine operations, maintenance, engineering and environmental departments. Typical insights include: enhanced understanding of root causes; recommendations for next best actions; and simulation of likely scenarios. The skills required for advanced analytics are not currently the domain of mining engineers. The professions required by tomorrow’s mines are likely to be diverse and multi-disciplinary, and will include control engineers, software engineers, mathematicians and statisticians. A case study is presented that correlates mobile equipment production delays with rainfall events across three mines on the east coast of Australia. One mine is shown to have significantly more rain related downtime than the other mines, providing compelling evidence to improve productive performance.

Nov 22, 2011

By R Gilbertson, N Freeman

Metallurgical accounting is key to the control and production planning process of any mining operation. This is even more crucial for complex operations involving mining, concentration, smelting, refining and marketing. The tracking of multiple metal product and contaminant components through the operation can improve process predictability and inventory management. Appropriate use can be made of æhigh quality dataÆ for strategic reserve utilisation, mining operations, milling operations, etc. This information enables the optimisation of all aspects of the mining and processing operations. This case study discusses a metal balance implementation for WMCÆs Olympic Dam operations; a large integrated mining, concentration and refining operation, which used an existing off the shelf statistical data reconciliation package developed for the oil industry. It was extended to track and balance the metal co-products across the entire integrated mining, mineral processing and refining plant. The key benefits discussed are tight integration with existing data collection systems, formalisation of previously informal processes, and leveraging the development and support available for a widely used package. The project provided a solution for the site metallurgical balance spanning the mine and processing plant. The solution facilitates a bridge between the planning and production worlds, using a common data model across the site.

Jan 1, 2002

By I A. Lamb

The Melbourne City Link Project has two tunnels, the Domain and Burnley Tunnels, which have been constructed by Transfield Obayashi Joint Venture (TOJV) under a design and construct contract. The two tunnels are located essentially under the Kings Domain, the Yarra River and, in the case of the longer Burnley Tunnel, under the inner suburb of Richmond. The Burnley Tunnel is 3.5 km long and reaches a depth of 65 m at the central Swan Street Shaft, the invert being at RL -60 m. The Domain Tunnel is 1.6 km long, with the invert reaching RL -20. The tunnels were driven, for the most part, in the siltstone and sandstone of the Silurian Age Melbourne Formation. Construction aspects of the driven tunnels as related to the engineering geology have been described by Hutchison et al (1998). The Silurian bedrock is a fractured rock aquifer that is connected to overlying alluvial aquifers. Excavation of the tunnels allowed temporary groundwater inflows which substantially de-pressurised portions of the various aquifers. This de-pressurisation provided the potential to accelerate on-going secondary consolidation rates of the Holocene Aged Coode Island Silt (CIS) and the older Quaternary Fishermens Bend Silt (FBS) deposits, in areas where these materials directly overly the aquifers. As a large portion of the urban area of South Melbourne and the old river course of the Yarra River contain extensive CIS deposits, and were within the drawdown influence of the tunnels, the management of the hydrogeological regime was very important. The permanent design of the tunnels comprised drained and undrained sections (a partially tanked design) which, along with some permanent recharge, provide long-term protection against the possibility of accelerated settlement rates. During construction TOJV implemented a comprehensive groundwater management plan to deal with issues related to the temporary drawdown of the aquifers and the temporary acceleration of settlement. This paper describes the hydrogeological regime, the effects of the tunnelling, the monitoring programs, the extensive temporary recharge system, and the consultation program that TOJV utilised to manage the hydrogeological issues.

Jan 1, 1999