Search Documents

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011

By D J Williams

Coal washery wastes comprise tailings, finer than 0.5 to 0.1 inn depending on the sophistication of the washery, and coarse reject, typically finer than 50 mm. Subaerial disposal of coal tailings slurry at about 30 per cent solids by mass results in the formation of a delta with an average slope of about 1 in 100, representing one extreme. The ravelling of coarse reject on loose-dumping, results in an angle of repose slope with an angle of about 37" (1 in 1.3), representing the other extreme. The pumped co-disposal of coal tailings and coarse reject results in the formation of an upper delta with an average slope of about to one in ten, between the two extremes. The depositional behaviour of these three waste streams is discussed and compared in this paper. The important depositional and material parameters, and a theoretical description of the processes involved, are also presented. Comparisons are made between the depositional behaviour of the various coal washery waste streams, and natural depositional systems, such as rivers, alluvial fans, and scree slopes.

Jan 1, 1998

The paper studies the flotation process of native Rare Earth minerals such as: bastnasite, monazite, mixed minerals of bastnasite and monazite, respectively, using the new effective collector - H205 which has been developed by Baotou Research Institute of Rare Earth, and describes their flotation properties. The test results of different ore samples show that at moderate pulp pH values, Rare Earth minerals can be effectively separated from barium and calcium bearing intergrowth minerals (barite and calcite) and high quality Rare Earth concentrates can be successfully obtained by H205 as collector with water glass as depressant. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and reagent dosage on the flotation were investigated in the test. Simultaneously, the paper explores the mechanism of the flotation separation of Rare Earth minerals from intergrowth minerals. The infrared spectra for H205 and RE cations by theorical analysis shows that H205 formed chelate complex with RE cations and adsorbed on the surfaces of RE minerals. The mechanism of the intergrowth minerals depressed by water glass can be explained as: H2Si03, HSi03 and gummy SiO2 hydrolised from water glass are selectively adsorbed on the gangue minerals, making them hydrophilic and depressed, under pulp pH value 8.5 to 9.5.

Jan 1, 1993

By S Ferguson, G Noble

The mining industry is facing economic pressures to treat more challenging and lower grade ore types, as well as pressure relating to environmental impact and social license to operate. Preconcentration through bulk ore sorting has the potential to benefit all these areas by enabling mining operations to divert material of low economic value prior to processing, thereby achieving higher feed grades and recovery, while reducing the processing plant and tailings dam footprint and capital required throughout the life of mine. The effectiveness of bulk ore sorting depends on the heterogeneity of material at the measurement location, as well as the accuracy and precision of the measurement. An understanding of ore heterogeneity can be assessed using drill core data, which provides metre by metre elemental assays. This paper reviews such data and assesses the grade distributions over different scales, which suggests that sufficient heterogeneity exists at mining scales to allow the potential for bulk ore sorting. Prompt Gamma Neutron Activation Analysis (PGNAA) technology has proven to be a successful measurement technique within many industries, including mining. PGNAA was first developed in the early 1980’s for the measurement of the elemental composition of bulk materials on a conveyor belt. Today, Pulsed Fast Thermal Neutron Activation (PFTNA) technology is also applied in elemental analysis of bulk materials and has some advantages for bulk ore sorting. In order to enable effective bulk ore sorting, however, a PGNAA/PFTNA analyser must be designed to provide a representative bulk ore analysis with the necessary accuracy and precision. Examples are presented to provide an understanding of the factors affecting PGNAA/PFTNA performance in relation to effective bulk ore sorting.

Nov 10, 2020

By B Chapman, R Nievergelt, J Hill

A major component of Sydney’s new South West Rail Link project is the Hume Highway Underpass (HHU), an 80 m long twin track mined tunnel excavated at a depth of just 5 m below the pavement of the Hume Highway; one of Australia’s busiest road corridors.In order to ensure a safe and efficient construction of the underpass without disruption to the Hume Highway traffic, design of the HHU required specific focus on the prediction and control of ground movements. This paper describes the design and construction solutions adopted in response to these challenging constraints. The paper also provides discussion on the observed behaviour of the underpass during construction and the results of a back analysis that was undertaken during construction.CITATION:Hill, J, Nievergelt, R and Chapman, B, 2014. Design and construction of Sydney’s South West Rail Link Hume Highway Underpass, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

It is no longer adequate when starting a new mine to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency which requires systematic involvement of people in continual improvement of production and commercial processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. The presentation will show the practical and successful use of these principles. This paper will introduce the case study and provide background material on True TQM.

Jan 1, 1995

By D R. Seaman, B Adamson, P Sharman, M McMahon

"The Telfer processing plant commissioned its pyrite regrind and flotation circuit in August 2012. The circuit was designed to regrind pyrite concentrate to a p80 of <30µm then float a gold and copper rich concentrate before tails from the flotation circuit fed the carbon-in-leach (CIL) circuit downstream. Expected benefits were: improved CIL performance that would result from the finer grind and a reduction in cyanide soluble copper to the CIL circuit, as well as a small increase in overall flotation circuit recovery. While the benefits of a finer grind were soon realised, recovery in the post-regrind flotation circuit (named the ‘pyrite recleaner circuit’) was consistently and significantly lower than that expected based on laboratory test work. Selectivity in the pyrite recleaner circuit was virtually nil and copper reporting to the CIL circuit did not change as a result of the pyrite recleaner circuit operation.A pulp chemistry survey of the plant and comparison with the lab showed that the dissolved oxygen (DO) demand in the plant was much higher than that in the lab. Lab flotation tests conducted using nitrogen gas instead of air resulted in recoveries similar to those from the plant. It was identified that the freshly ground pyrite surfaces exiting the regrind mill were consuming oxygen in the slurry and there was insufficient oxygen available for collector adsorption and pyrite depression to occur. Test work, using a pilot regrind mill, showed that a reduction in grind size resulted in an increase in DO demand.A range of oxidising agents were tested in the laboratory and using a pilot flotation rig set-up in the plant. Oxygen was found to be the most reliable and effective agent and options for increasing oxygen delivery to the plant were explored. Scale-up from the lab oxygen requirement to the plant is difficult and efforts to implement a permanent solution for meeting the DO demand in the plant are ongoing.Citation:McMahon, M, Seaman, D R, Sharman, P, Adamson, B and Seaman, B A, 2016. Optimising the Telfer Pyrite Regrind Circuit - Effect of Dissolved Oxygen Demand, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S H. Begg

"*This is an abstract only*Most technical and economic analyses are performed to reduce uncertainty to help make decisions. Decision-making is about ranking alternatives - rarely are precise predictions required, if even possible. This simple observation has profound implications for modelling approaches, how they deal with uncertainty and the reliability of information provided by subject matter experts.CITATION:Begg, S H, 2013. Some reflections on uncertainty, decisions, models and people, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 3-6 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By B Liu, W J. Zhang, S Saydam, B Li

Rock bolts are commonly used to reinforce ground in underground mining and civil tunnel environments. Rock bolts serve two main functions: i) they suspend large, loose blocks of ground, and ii) provide a protective pressure arch to restrain the deformation in an excavated void. Automated and precise tracking of rock bolt positions can assist with the operational success of ground support by reducing the amount of labour required in current manual practices. A point cloud is a large list of x, y and z coordinates in three-dimensional space, that when visualised, show a precise 3D representation of a physical environment. Point cloud data can be collected using accurate LiDAR scanners. These scanners can be mounted on a stationary tripod or on a moving vehicle. A key way point cloud data is used is in the bolt detection project being completed in conjunction with UNSW Sydney, which aims to provide an automated location of underground rock bolts from LiDAR scans. The immediate challenge with identifying rock bolts is that they constitute a very small portion of the data set amounting to approximately 0.01 per cent of some of the collected civil tunnel data. The process of detecting rock bolts from point clouds therefore requires a quick elimination of large background data while still preserving the bolt data. A further challenge is that the geometry of underground environments can often be very complex and non-uniform. To overcome these challenges, a two-step coarse to fine deep learning approach is taken. The first step is a coarse background elimination step aimed at removing as much of the background data as possible. The second step is a finer classification method, which uses deep learning to further segment the bolts from the remaining background. Additionally, a computer vision module is being implemented, which is expected to increase the detection rate by adding another dimension to the training data set.

Nov 29, 2022

By E Philippa, B Miller

Material characterisation, ore sequencing and process capability are commonly regarded as the key parameters to consider in designing and operating an effective pit to plant supply chain. Therefore, an understanding of rock mass properties is the starting point for controlling the presentation of problematic material to the ore handling plant and optimising process utilisation. There are different methodologies for characterising problematic material and ore handleability which exist across a spectrum of sophistication. At one end of this spectrum are simple indices built using first principles geology and at the other are complex algorithms developed using advanced analytical methods, machine learning and ore traceability. Regardless of the method, without an integrated process for careful management of problematic ore, material handling delays (ie blocked, bridged, blinded and buried events) will interrupt the stable flow of production. The ability of the ore control geologist to mitigate these delays is central to the ore handleability challenge. This paper describes a quick and easy solution that links the presentation of ore to the operating window at the crusher. This operating window is based on material characterisation, using the physical, textural and mechanical properties of the rock mass, and crusher performance. It also describes how a basic problematic ore index (POI) can be developed using ore tracking to the production face, petrographic studies of ore texture and mineralogy, and existing variables in the geological model. Finally, this paper will demonstrate that by coding the POI into the geological model for mine planning, together with performance monitoring through compliance to plan routines, material handling delays at the crusher can be reduced, unlocking significant resource value.

Mar 22, 2022

By J D. Illescas, S N. Arnold, D R. Shaw

Ion exchange (IX) as a primary production technique has been applied commercially since the 1950s; its application in the uranium industry continues to be widespread and is utilised to a lesser degree in the gold industry. The majority of ion exchange applications, outside of gold and uranium, have primarily been for secondary metal recovery and impurity removal. Newer developments in the application of ion exchange, as well as changes in regulatory requirements, are bringing about the wider use of ion exchange as a primary production technique not only for high value metals such as uranium, platinum group metals (PGM), refractory metals and rare earths, but also looking at base metals such as nickel and copper. The ability to build lower-cost, safer, less polluting processing plants with smaller footprints is driving a greater interest in IX, with the main competitors remaining solvent extraction and carbon-in-pulp/leach. This paper discusses a number of areas where IX has been applied and its advantages compared with other techniques.CITATION:Shaw, D R, Arnold, S N and Illescas, J D, 2012. Ion exchange in hydrometallurgy - Secondary metal removal or primary production technique?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 17-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By N Murthy

Alumina is a major impurity in Australian iron ores and as the higher grade ores become depleted there will be a stronger focus on treating lower grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the alumina content. High alumina in iron ore is deleterious in that it can:• produce slags with lower desulfurising capacity,• reduce sinter/pellet strength and quality, and• produce higher slag volume and increase slag viscosity.Meeting iron ore quality specifications for alumina by blending ore from different sources will eventually be insufficient. Hence, innovative flow sheets based on new and commercially available technologies will be required. Their advantages and disadvantages, the testing methodologies and the challenges and diffi culties involved in reducing the alumina content of iron ores are presented and discussed.

Jul 11, 2011

By D Connelly

Quartz deposits are common in nature but the presence of quartz suitable for yielding high purity quartz is exceedingly rare. This paper describes a test work study on producing high purity quartz (HPQ) product to meet the tight product specifications of greater than 99.97per cent, including four and even five nines, for uses including, lighting and fibre optics and modern-day high efficiency solar panels. Due to demand in renewable energy applications the market for high purity silica solar panels known for their increasing efficiency and durability is rapidly growing. Demand continues to rise for the use of high purity quartz in semiconductors, electronics, imaging and sensor markets. Microelectronic components are created by chemically fabricating wafers of semiconductors such as silicon to obtain the desired transport of electrical charge and control of the current. The production of silicon metal from high purity quartz has been designated a Strategic Mineral by the European Commission and by the US Department of Justice due to the growing significance of this metal in various industries. The subsequent processing of quartz is the key step to adding value and aiding technological advances. Overall, the high purity quartz market is a highly secretive, specialised market with increasing opportunities for stakeholders. The attempt to produce HPQ in this work was carried out using an Australian quartz ore following a typical HPQ process flow sheet. The unit processes included primary crushing, scrubbing, magnetic separation, flotation, acid leaching followed by hot chlorination. The results indicate that grinding of quartz requires specialist equipment due to the hardness and extreme abrasiveness of the ore leading to additional iron contamination in the ground ore. The critical impurities were aluminium, iron, sodium, potassium, lithium, titanium, zircon, calcium and magnesium. The chemical refining was found effective. The hot chlorination process needed to be done at 1200°C in a chlorine – hydrogen chloride gas atmosphere. The risk of any gas being released during this stage is very serious and only specialist companies should and can carry out this step. More recent studies reported many new options that appear to facilitate the production of HPQ with the requisite purities more easily, but costly equipment along with highly trained operators are required and hence unlikely to become available in standard metallurgical laboratories any time soon.

Sep 1, 2024

By Cloutier JY, Quinn P, LeClerc A, Dube G, Agar GE

Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer. The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared with a readily available but under utilised method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate.

Jan 1, 1993

By D Johns, L Murray

This paper discusses pore pressures in the embankments of tailings dams by comparing real world data with common design assumptions. Assessment of pore pressures has implications on material behaviour interpretation from CPT investigations and, therefore, on the design. For example, the assumption of hydrostatic pressure is conservative for limit equilibrium stability analyses but may be un-conservative in assessing the potential for contractive behaviour and strength loss during shearing. This paper presents some real world data, the investigation methods to determine the pore pressures, and subsequent interpretation of CPT data and material parameters such as the state parameter. It also examines the design implications of assuming a hydrostatic pressure distribution, by comparing results from that assumption with those obtained using the real pore pressures.CITATION:Johns, D and Murray, L, 2018. Characterisation of pore pressure in tailings dams and the implications for design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 239–249 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The Porgera gold project is now in its seventh year of operation as one of the world's prime gold mining projects in one of the most underdeveloped and remote regions of the world. The unique gold deposit was development in stages to its present size of operation with an underground mine of 2000tpd, an open pit operation moving 210,000tpd and a complex metallurgical plant treating an average of 16,500tpd of ore. During the past years the operation had to address an array of issues relating to the "development" of the region and this is still ongoing. Development means different things to different people and though the parties that signed the different agreements relating to the Mining Development Contract were aware of this, none has real- ised the extent to which this is true. The developing company (a joint venture between Placer Pacific as the Manager, Goldfields Porgera, Highlands Gold and the Government of PNG), provided funds for risky exploration and the capital for development of the project. Its shareholders ex- pect an economic and viable mine operation from the deposit to ensure them returns on their investment. The local people gave up their land, their isolated way of living and accepted to be out of their comfort zone for some time in anticipation of a better lifestyle and economic benefits in support of that lifestyle. The PNG Government has a leg in both camps and expects both outcomes at the same time. The Government is also the regulator and expects compliance on top of that. If development in general is to be successful, all parties must substantially satisfy all expectations. It is evident that the outcome of some elements of development are reasonably defined (i.e. develop a viable mine to exploit the deposit), whilst other elements are moving targets (i.e. a better lifestyle). The seeds for conflict are thus abundantly present and to resolve them requires the will of all parties in all areas to come to a solution. This path to problem solving is many times torturous as each party comes from a different culture and background and has a different understanding of the parameters in the equation.

Jan 1, 1997

By F Butler, G E. Batley, A C. Hogan, A R. Butler

The ANZECC/ARMCANZ (2000) Water Quality Guidelines (the Guidelines) are the primary reference used in Australia and New Zealand for managing and regulating water quality. For most mining operations in Queensland, the environmental authority (EA – licence) incorporates the national default guideline values (GVs) for ecosystem protection as trigger levels (TLs). Exceedances of TLs ‘trigger’ further investigation and reporting. A review of the surface water compliance history at a metalliferous mine in North West Queensland identified minor exceedances of the cobalt GV as a common trigger for investigation and compliance reporting.The reliability of GVs is dependent on the availability and quality of ecotoxicology data for the relevant contaminant. The current national default GV for cobalt of 1.4 µg/L is classified as a low reliability GV due to the lack of available data at the time it was derived (ANZECC/ARMCANZ, 2000).The Guidelines are presently being revised and the toxicant GVs will be available as a set of web-based values and associated technical briefs. The new platform will enable the timely revision of existing GVs and inclusion of GVs for additional toxicants. Cobalt was considered a priority toxicant for the Guidelines’ revision, but was not included in the revision process.A preliminary review of the international literature indicated that at least 15 additional chronic cobalt toxicity studies had been published since 2000, sufficient to derive a high reliability cobalt GV using the protocols developed for the revision of the Guidelines (Batley et al, 2014; Warne et al, 2015). This presented an opportunity to improve environmental management by increasing the reliability of the performance measure.CITATION:Hogan, A C, Butler, A R, Butler, F and Batley, G E, 2016. Derivation of high reliability water quality guideline values for cobalt in freshwaters – improving water quality guidelines for better water quality compliance management in mining, in Proceedings Life-of-Mine 2016 Conference , pp 205–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By T C. Souza Pinto, M Safari, F S. Hoseinian, D Deglon, L Leal Filhoc

In this study, the effect of hydrodynamic parameters on the iron ore reverse was investigated in a mechanical flotation cell. The work carries out using the case study of Iron ore from Vale in Brazil. The influence of hydrodynamic factors such as froth height, impeller speed, superficial gas velocity and solids percentage were evaluated on the quartz flotation. The results showed that the hydrodynamic conditions have a great effect on the flotation performance, especially on the fine and coarse quartz. The size-by-size analysis of the froth products showed that froth height, impeller speed, superficial gas velocity and solids percentage have a significant effect on true flotation quartz particles. The increase in the froth height decreased the recovery of quartz particles. The increase in the impeller speed increases the recovery of quartz particles to an optimum. The increase in the superficial gas velocity improved the flotation of coarse quartz particles. The increase in the solids percentage increases the recovery of quartz particles.

Sep 18, 2023

By G Hobart

Laboratory flotation tests were conducted to investigate the role of pH, zinc sulfate and potassium metabisulfite in the flotation of galena and marmatite in the Broken Hill orebody. Marmatite was depressed under alkaline conditions alone, however the addition of the two depressants, either individually or combined, resulted in the greatest selectivity. The use of zinc sulfate under alkaline conditions resulted in good selectivity whilst maintaining a high lead recovery. The addition of potassium metabisulfite under alkaline conditions reduced zinc recovery, but high additions reduced lead recovery. The addition of both depressants at alkaline pH produced the best result, with a lead concentrate of 72.6 per cent at 98 per cent recovery with less than four per cent zinc recovery.

Jan 1, 2005